Search

The rapid progress of electronic devices has necessitated efficient heat dissipation within boiling cooling systems, underscoring the need for improvements in boiling heat transfer coefficient (HTC) and critical heat flux (CHF). While different approaches for micropillar fabrication on copper or silicon substrates have been developed and have shown significant boiling performance improvements, such enhancement approaches on aluminum surfaces are not broadly investigated, despite their industrial applicability. This study introduces a scalable approach to engineering hierarchical micro-nano structures on aluminum surfaces, aiming to simultaneously increase HTC and CHF. One set of samples was produced using a combination of nanosecond laser texturing and chemical etching in hydrochloric acid, while another set underwent an additional laser texturing step. Three distinct micropillar patterns were tested under saturated pool boiling conditions using water at atmospheric pressure. Our findings reveal that microcavities created atop pillars successfully facilitate nucleation and micropillars representing nucleation site areas on a microscale, leading to an enhanced HTC up to 242 kW m−2 K−1. At the same time, the combination of the surrounding hydrophilic porous area enables increased wicking and pillar patterning, defining the vapor–liquid pathways on a macroscale, which leads to an increase in CHF of up to 2609 kW m−2. [ABSTRACT FROM AUTHOR]

Prior studies have evidenced the potential for enhancing boiling heat transfer through modifications of surface or fluid properties. The deployment of nanofluids in pool boiling systems is challenging due to the deposition of nanoparticles on structured surfaces, which may result in performance deterioration. This study addresses the use of TiO2–water nanofluids (mass concentrations of 0.001 wt.% and 0.1 wt.%) in pool boiling heat transfer and concurrent mitigation of nanoparticle deposition on superhydrophobic laser-textured copper surfaces. Samples, modified through nanosecond laser texturing, were subjected to boiling in an as-prepared superhydrophilic (SHPI) state and in a superhydrophobic state (SHPO) following hydrophobization with a self-assembled monolayer of fluorinated silane. The boiling performance assessment involved five consecutive boiling curve runs under saturated conditions at atmospheric pressure. Results on superhydrophilic surfaces reveal that the use of nanofluids always led to a deterioration of the heat transfer coefficient (up to 90%) compared to pure water due to high nanoparticle deposition. The latter was largely mitigated on superhydrophobic surfaces, yet their performance was still inferior to that of the same surface in water. On the other hand, CHF values of 1209 kW m−2 and 1462 kW m−2 were recorded at 0.1 wt.% concentration on both superhydrophobic and superhydrophilic surfaces, respectively, representing a slight enhancement of 16% and 27% compared to the results obtained on their counterparts investigated in water. [ABSTRACT FROM AUTHOR]

The enhancement of boiling heat transfer has been extensively shown to be achievable through surface texturing or fluid property modification, yet few studies have investigated the possibility of coupling both enhancement approaches. The present work focuses on exploring the possibility of concomitant enhancement of pool boiling heat transfer by using TiO2-water nanofluid in combination with laser-textured copper surfaces. Two mass concentrations of 0.001 wt.% and 0.1 wt.% are used, along with two nanoparticle sizes of 4–8 nm and 490 nm. Nanofluids are prepared using sonification and degassed distilled water, while the boiling experiments are performed at atmospheric pressure. The results demonstrate that the heat transfer coefficient (HTC) using nanofluids is deteriorated compared to using pure water on the reference and laser-textured surface. However, the critical heat flux (CHF) is significantly improved at 0.1 wt.% nanoparticle concentration. The buildup of a highly wettable TiO2 layer on the surface is identified as the main reason for the observed performance. Multiple subsequent boiling experiments using nanofluids on the same surface exhibited a notable shift in boiling curves and their instability at higher concentrations, which is attributable to growth of the nanoparticle layer on the surface. Overall, the combination of nanofluids boiling on a laser-textured surface proved to enhance the CHF after prolonged exposure to highly concentrated nanofluid, while the HTC was universally and significantly decreased in all cases. [ABSTRACT FROM AUTHOR]