Search

This work focused on the solubility of ethane in three promising ionic liquids {1-Hexyl-3-methylimidazolium bis(trifluormethylsulfonyl) imide [HMIM][Tf2N], 1-Butyl-3-methyl-imidazolium dimethyl-phosphate [BMIM][DMP], and 1-Propyl-3-methylimidazolium bis(trifluoromethyl-sulfonyl)-imide [PMIM][Tf2N]}. The solubilities were measured at 303.15 K to 343.15 K and pressures up to 1.4 MPa using a gravimetric microbalance. The overall ranking of ethane solubility in the ionic liquids from highest to lowest is the following: [HMIM][Tf2N] > [PMIM][Tf2N] > [BMIM][DMP]. The Peng–Robinson equation of state was used to model the experimental data using three different mixing rules: van der Waals one, van der Waals two, and Wong–Sandler mixing rules combined with the Non-Random Two-Liquid model. The average absolute deviations for the three mixing rules for the ionic liquids at the three temperatures were 4.39, 2.45, and 2.45%, respectively. Henry's Law constants for ethane in [BMIM] [DMP] were the highest (lowest solubility) amongst other ionic liquids studied in this work. The solubility ranking for the 3 ILs was confirmed by calculating their overall polarity parameter (N) using COSMO-RS. The selectivity of CO2 over C2H6 was estimated at three temperatures, and the overall ranking of the selectivity was in the following order: [PMIM][Tf2N] > [BMIM][DMP] > [HMIM][Tf2N] > Selexol. Selexol is an efficient and widely used physical solvent in gas sweetening. It has lower selectivity than the three ionic liquids studied. [PMIM][Tf2N], a promising solvent, has the highest selectivity among the three ILs studied and would, therefore, be the best choice if, in addition to carbon dioxide capture, ethane co-absorption was to be avoided. The enthalpy and entropy of solvation at infinite dilution were also estimated. [ABSTRACT FROM AUTHOR]

This work focused on the solubility of ethane in three promising ionic liquids {1-Hexyl-3-methylimidazolium bis(trifluormethylsulfonyl) imide [HMIM][Tf2N], 1-Butyl-3-methyl-imidazolium dimethyl-phosphate [BMIM][DMP], and 1-Propyl-3-methylimidazolium bis(trifluoromethyl-sulfonyl)-imide [PMIM][Tf2N]}. The solubilities were measured at 303.15 K to 343.15 K and pressures up to 1.4 MPa using a gravimetric microbalance. The overall ranking of ethane solubility in the ionic liquids from highest to lowest is the following: [HMIM][Tf2N] > [PMIM][Tf2N] > [BMIM][DMP]. The Peng–Robinson equation of state was used to model the experimental data using three different mixing rules: van der Waals one, van der Waals two, and Wong–Sandler mixing rules combined with the Non-Random Two-Liquid model. The average absolute deviations for the three mixing rules for the ionic liquids at the three temperatures were 4.39, 2.45, and 2.45%, respectively. Henry’s Law constants for ethane in [BMIM] [DMP] were the highest (lowest solubility) amongst other ionic liquids studied in this work. The solubility ranking for the 3 ILs was confirmed by calculating their overall polarity parameter (N) using COSMO-RS. The selectivity of CO2 over C2H6 was estimated at three temperatures, and the overall ranking of the selectivity was in the following order: [PMIM][Tf2N] > [BMIM][DMP] > [HMIM][Tf2N] > Selexol. Selexol is an efficient and widely used physical solvent in gas sweetening. It has lower selectivity than the three ionic liquids studied. [PMIM][Tf2N], a promising solvent, has the highest selectivity among the three ILs studied and would, therefore, be the best choice if, in addition to carbon dioxide capture, ethane co-absorption was to be avoided. The enthalpy and entropy of solvation at infinite dilution were also estimated.

Glycerin, a low-valued waste from biodiesel production, and dopamine were used as precursors for adsorbent materials. The study is centered on the preparation and application of microporous activated carbon as adsorbent materials in the separation of ethane/ethylene and of gases that are natural gas or landfill gas components (ethane/methane and carbon dioxide/methane). The activated carbons were produced by the following sequence reactions: facile carbonization of a glycerin/dopamine mixture and chemical activation. Dopamine allowed the introduction of nitrogenated groups that improved the selectivity of the separations. The activating agent was KOH, but its mass ratio was kept lower than one to improve the sustainability of the final materials. The solids were characterized by N2 adsorption/desorption isotherms, SEM, FTIR spectroscopy, elemental analysis, and point of zero charges (pHPZC). The order for adsorption of the different adsorbates (in mmolg−1) on the most well performing material—Gdop0.75—is methane (2.5) < carbon dioxide (5.0) < ethylene (8.6) < ethane (8.9). [ABSTRACT FROM AUTHOR]

Glycerin, a low-valued waste from biodiesel production, and dopamine were used as precursors for adsorbent materials. The study is centered on the preparation and application of microporous activated carbon as adsorbent materials in the separation of ethane/ethylene and of gases that are natural gas or landfill gas components (ethane/methane and carbon dioxide/methane). The activated carbons were produced by the following sequence reactions: facile carbonization of a glycerin/dopamine mixture and chemical activation. Dopamine allowed the introduction of nitrogenated groups that improved the selectivity of the separations. The activating agent was KOH, but its mass ratio was kept lower than one to improve the sustainability of the final materials. The solids were characterized by N2 adsorption/desorption isotherms, SEM, FTIR spectroscopy, elemental analysis, and point of zero charges (pHPZC). The order for adsorption of the different adsorbates (in mmolg−1) on the most well performing material—Gdop0.75—is methane (2.5) < carbon dioxide (5.0) < ethylene (8.6) < ethane (8.9).

We report on a fiber-coupled, quartz-enhanced photoacoustic spectroscopy (QEPAS) near-IR sensor for sequential detection of methane (CH4 or C1) and ethane (C2H6 or C2) in air. With the aim of developing a lightweight, compact, low-power-consumption sensor suitable for unmanned aerial vehicles (UAVs)-empowered environmental monitoring, an all-fiber configuration was designed and realized. Two laser diodes emitting at 1653.7 nm and 1684 nm for CH4 and C2H6 detection, respectively, were fiber-combined and fiber-coupled to the collimator port of the acoustic detection module. No cross talk between methane and ethane QEPAS signal was observed, and the related peak signals were well resolved. The QEPAS sensor was calibrated using gas samples generated from certified concentrations of 1% CH4 in N2 and 1% C2H6 in N2. At a lock-in integration time of 100 ms, minimum detection limits of 0.76 ppm and 34 ppm for methane and ethane were achieved, respectively. The relaxation rate of CH4 in standard air has been investigated considering the effects of H2O, N2 and O2 molecules. No influence on the CH4 QEPAS signal is expected when the water vapor concentration level present in air varies in the range 0.6–3%.

The biological production of ethanol from ethane for the utilization of ethane in natural gas was investigated under ambient conditions using whole-cell methanotrophs possessing methane monooxygenase. Several independent variables including ethane concentration and biocatalyst amounts, among other factors, were optimized for the enhancement of ethane-to-ethanol bioconversion. We obtained 0.4 g/L/h of volumetric productivity and 0.52 g/L of maximum titer in optimum batch reaction conditions. In this study, we demonstrate that the biological gas-to-liquid conversion of ethane to ethanol has potent technical feasibility as a new application of ethane gas.

Ab initio total-energy calculations of the elementary reaction steps leading to acetylene, ethylene and ethane formation and their decomposition on Fe(100) are described. Alongside the endothermicity of all the formation reactions, the crucial role played by adsorbed ethyl as main precursor towards both ethylene and ethane formation, characterises Fe(100) surface reactivity towards C2Hx (x = 0–6) hydrocarbon formation in the low coverage limit. A comprehensive scheme based on three viable mechanisms towards ethyl formation on Fe(100), including methyl/methylene coupling, methyl/methylidyne coupling followed by one hydrogenation and methyl/carbon coupling followed by two hydrogenations, is the main result of this article.

Supercritical fluid extraction of all-E-lycopene from tomato industrial wastes (mixture of skins and seeds) was carried out in a semi-continuous flow apparatus using ethane as supercritical solvent. The effect of pressure, temperature, feed particle size, solvent superficial velocity and matrix initial composition was evaluated. Moreover, the yield of the extraction was compared with that obtained with other supercritical solvents (supercritical CO2 and a near critical mixture of ethane and propane). The recovery of all-E-lycopene increased with pressure, decreased with the increase of the particle size in the initial stages of the extraction and was not practically affected by the solvent superficial velocity. The effect of the temperature was more complex. When the temperature increased from 40 to 60 °C the recovery of all-E-lycopene increased from 80 to 90%. However, for a further increase to 80 °C, the recovery remained almost the same, indicating that some E-Z isomerization could have occurred, as well as some degradation of lycopene. The recovery of all-E-lycopene was almost the same for feed samples with different all-E-lycopene content. Furthermore, when a batch with a higher all-E-lycopene content was used, supercritical ethane and a near critical mixture of ethane and propane showed to be better solvents than supercritical CO2 leading to a faster extraction with a higher recovery of the carotenoid.

The energy change on each Occupied Molecular Orbital as a function of rotation about the C-C bond in ethane was studied using the B3LYP, mPWB95 functional and MP2 methods with different basis sets. Also, the effect of the ZPE on rotational barrier was analyzed. We have found that σ and π energies contribution stabilize a staggered conformation. The σs molecular orbital stabilizes the staggered conformation while the stabilizes the eclipsed conformation and destabilize the staggered conformation. The πz and molecular orbitals stabilize both the eclipsed and staggered conformations, which are destabilized by the πv and molecular orbitals. The results show that the method of calculation has the effect of changing the behavior of the energy change in each Occupied Molecular Orbital energy as a function of the angle of rotation about the C–C bond in ethane. Finally, we found that if the molecular orbital energy contribution is deleted from the rotational energy, an inversion in conformational preference occurs.

Ab initio total-energy calculations of the elementary reaction steps leading to acetylene, ethylene and ethane formation and their decomposition on Fe(100) are described. Alongside the endothermicity of all the formation reactions, the crucial role played by adsorbed ethyl as main precursor towards both ethylene and ethane formation, characterises Fe(100) surface reactivity towards C2Hx (x = 0-6) hydrocarbon formation in the low coverage limit. A comprehensive scheme based on three viable mechanisms towards ethyl formation on Fe(100), including methyl/methylene coupling, methyl/methylidyne coupling followed by one hydrogenation and methyl/carbon coupling followed by two hydrogenations, is the main result of this article. [ABSTRACT FROM AUTHOR]

Supercritical fluid extraction of all-E-lycopene from tomato industrial wastes (mixture of skins and seeds) was carried out in a semi-continuous flow apparatus using ethane as supercritical solvent. The effect of pressure, temperature, feed particle size, solvent superficial velocity and matrix initial composition was evaluated. Moreover, the yield of the extraction was compared with that obtained with other supercritical solvents (supercritical CO2 and a near critical mixture of ethane and propane). The recovery of all-E-lycopene increased with pressure, decreased with the increase of the particle size in the initial stages of the extraction and was not practically affected by the solvent superficial velocity. The effect of the temperature was more complex. When the temperature increased from 40 to 60 °C the recovery of all-E-lycopene increased from 80 to 90%. However, for a further increase to 80 °C, the recovery remained almost the same, indicating that some E-Z isomerization could have occurred, as well as some degradation of lycopene. The recovery of all-E-lycopene was almost the same for feed samples with different all-E-lycopene content. Furthermore, when a batch with a higher all-E-lycopene content was used, supercritical ethane and a near critical mixture of ethane and propane showed to be better solvents than supercritical CO2 leading to a faster extraction with a higher recovery of the carotenoid. [ABSTRACT FROM AUTHOR]

The energy change on each Occupied Molecular Orbital as a function of rotation about the C-C bond in ethane was studied using the B3LYP, mPWB95 functional and MP2 methods with different basis sets. Also, the effect of the ZPE on rotational barrier was analyzed. We have found that σ and π energies contribution stabilize a staggered conformation. The σs* molecular orbital stabilizes the σs staggered conformation while the stabilizes the eclipsed conformation and destabilize the staggered conformation. The πz* and πz molecular orbitals stabilize both the eclipsed and staggered conformations, which are destabilized by the πv andπy* molecular orbitals. The results show that the method of calculation has the effect of changing the behavior of the energy change in each Occupied Molecular Orbital energy as a function of the angle of rotation about the C-C bond in ethane. Finally, we found that if the molecular orbital energy contribution is deleted from the rotational energy, an inversion in conformational preference occurs. [ABSTRACT FROM AUTHOR]

We report on a fiber-coupled, quartz-enhanced photoacoustic spectroscopy (QEPAS) near-IR sensor for sequential detection of methane (CH4 or C1) and ethane (C2H6 or C2) in air. With the aim of developing a lightweight, compact, low-power-consumption sensor suitable for unmanned aerial vehicles (UAVs)-empowered environmental monitoring, an all-fiber configuration was designed and realized. Two laser diodes emitting at 1653.7 nm and 1684 nm for CH4 and C2H6 detection, respectively, were fiber-combined and fiber-coupled to the collimator port of the acoustic detection module. No cross talk between methane and ethane QEPAS signal was observed, and the related peak signals were well resolved. The QEPAS sensor was calibrated using gas samples generated from certified concentrations of 1% CH4 in N2 and 1% C2H6 in N2. At a lock-in integration time of 100 ms, minimum detection limits of 0.76 ppm and 34 ppm for methane and ethane were achieved, respectively. The relaxation rate of CH4 in standard air has been investigated considering the effects of H2O, N2 and O2 molecules. No influence on the CH4 QEPAS signal is expected when the water vapor concentration level present in air varies in the range 0.6–3%. [ABSTRACT FROM AUTHOR]

We report, to our knowledge, the first optical detection scheme for short-chained hydrocarbon isotopologues. The sensor system is based on photoacoustic spectroscopy (PAS). Two continuous wave, thermoelectrically cooled, distributed feedback interband cascade lasers (DFB-ICLs) with emission wavelengths around 3.33 and 3.38 μm, respectively, served as light sources. The investigations comprised the main stable carbon isotopologues of methane (12CH4, 13CH4), ethane (12CH3-12CH3, 13CH3-12CH3, 13CH3-13CH3), and propane (12CH3-12CH2-12CH3, 13CH3-12CH2-12CH3). They were selected because of their importance for numerous applications from climate and planetary research to natural gas exploration. Multiple measurements of single components in nitrogen and synthetic mixtures were conducted at room temperature and atmospheric pressure. Depending on the investigated hydrocarbon isotopologue, detection limits ranging from 0.043 ppmv to 3.4 ppmv were achieved. For a selective concentration determination, multivariate analysis (MVA) was applied. Partial least-squares regression (PLSR) was used to calculate concentrations from the PA spectra. The implementation of MVA has shown that the PA setup in principle works reliably and that the selective concentration determination of short-chained hydrocarbon isotopologues is possible. [ABSTRACT FROM AUTHOR]

The biological production of ethanol from ethane for the utilization of ethane in natural gas was investigated under ambient conditions using whole-cell methanotrophs possessing methane monooxygenase. Several independent variables including ethane concentration and biocatalyst amounts, among other factors, were optimized for the enhancement of ethane-to-ethanol bioconversion. We obtained 0.4 g/L/h of volumetric productivity and 0.52 g/L of maximum titer in optimum batch reaction conditions. In this study, we demonstrate that the biological gas-to-liquid conversion of ethane to ethanol has potent technical feasibility as a new application of ethane gas. [ABSTRACT FROM AUTHOR]

Silicalite is an important nanoporous material that finds applications in several industries, including gas separation and catalysis. While the sorption, structure, and dynamics of several molecules confined in the pores of silicalite have been reported, most of these studies have been restricted to low pressures. Here we report a comparative study of sorption, structure, and dynamics of CO2 and ethane in silicalite at high pressures (up to 100 bar) using a combination of Monte Carlo (MC) and molecular dynamics (MD) simulations. The behavior of the two fluids is studied in terms of the simulated sorption isotherms, the positional and orientational distribution of sorbed molecules in silicalite, and their translational diffusion, vibrational spectra, and rotational motion. Both CO2 and ethane are found to exhibit orientational ordering in silicalite pores; however, at high pressures, while CO2 prefers to reside in the channel intersections, ethane molecules reside mostly in the sinusoidal channels. While CO2 exhibits a higher self-diffusion coefficient than ethane at low pressures, at high pressures, it becomes slower than ethane. Both CO2 and ethane exhibit rotational motion at two time scales. At both time scales, the rotational motion of ethane is faster. The differences observed here in the behavior of CO2 and ethane in silicalite pores can be seen as a consequence of an interplay of the kinetic diameter of the two molecules and the quadrupole moment of CO2. [ABSTRACT FROM AUTHOR]