Search

Biodegradable polymers have recently become attractive and have been increasingly used as matrix materials to replace fossil plastics due to concerns about the environmental issue. However, their application areas are limited due to their high costs and natural properties. In this study, we fabricated ecofriendly and economical polybutylene adipate terephthalate (PBAT) composites loaded with various concentrations of wood flour (WF) to investigate the effects on the PBAT and WF interfaces as well as the physical properties of the WF/PBAT biocomposites. Then, WF was acetylated with acetic anhydride, and the effect of WF acetylation on the mechanical and thermal properties of the biocomposites were investigated. The results showed that the tensile strength, tensile modulus, flexural strength and flexural modulus increased with WF loading in the composites, and acetylation could not only further increase these properties, but also increase the impact strength and elongation at break. The incorporation of WF would weaken the thermal stability of PBAT, but the thermal stability of the biocomposite could be improved after WF acetylation. The cold crystallization temperature and hydrophobicity of the WF/PBAT samples would be increased with the increasing load of the WF, while the melting enthalpy and the crystallinity of the samples reduced gradually. A morphological analysis of the modified composites revealed that the matrix exhibited greater interfacial interactions with the WF compared to the WF/PBAT. Considering the much lower cost of WF compared to PBAT, the improved properties of WF/PBAT biocomposites will make it economically competitive with other commercial polymers, and these biocomposites should have much wider application areas. [ABSTRACT FROM AUTHOR]

The development of the paper industry has led to the discharge of a large amount of papermaking waste liquid containing lignosulfonate. These lignin black liquids cause a lot of pollution in nature, which runs counter to the current environmental protection strategy under the global goal. Through the development and use of lignosulfonate in papermaking waste liquid to increase the utilization of harmful substances in waste liquid, we aim to promote waste liquid treatment and reduce environmental pollution. This paper proposes a new strategy to synthesize novel glue-free biocomposites with high-performance interfacial compatibility from papermaking by-product sodium lignosulfonate/chitosan (L/C) and waste bamboo. This L/C bamboo biocomposite material has good mechanical properties and durability, low formaldehyde emissions, a high recovery rate, meets the requirements of wood-based panels, and reduces environmental pollution. This method is low in cost, has the potential for large-scale production, and can effectively reduce the environmental pollution of the paper industry, promoting the recycling of biomass and helping the future manufacture of glue-free panels, which can be widely used in the preparation of bookcase, furniture, floor and so on. [ABSTRACT FROM AUTHOR]

Biodegradable polymers have recently become attractive and have been increasingly used as matrix materials to replace fossil plastics due to concerns about the environmental issue. However, their application areas are limited due to their high costs and natural properties. In this study, we fabricated ecofriendly and economical polybutylene adipate terephthalate (PBAT) composites loaded with various concentrations of wood flour (WF) to investigate the effects on the PBAT and WF interfaces as well as the physical properties of the WF/PBAT biocomposites. Then, WF was acetylated with acetic anhydride, and the effect of WF acetylation on the mechanical and thermal properties of the biocomposites were investigated. The results showed that the tensile strength, tensile modulus, flexural strength and flexural modulus increased with WF loading in the composites, and acetylation could not only further increase these properties, but also increase the impact strength and elongation at break. The incorporation of WF would weaken the thermal stability of PBAT, but the thermal stability of the biocomposite could be improved after WF acetylation. The cold crystallization temperature and hydrophobicity of the WF/PBAT samples would be increased with the increasing load of the WF, while the melting enthalpy and the crystallinity of the samples reduced gradually. A morphological analysis of the modified composites revealed that the matrix exhibited greater interfacial interactions with the WF compared to the WF/PBAT. Considering the much lower cost of WF compared to PBAT, the improved properties of WF/PBAT biocomposites will make it economically competitive with other commercial polymers, and these biocomposites should have much wider application areas.

The emerging concepts of sustainable textiles and controlled production strategy demands ideally zero emissions of contaminants into the aquatic environment. However, the currently in-practiced conventional processes in textiles dispose of a number of contaminants especially super toxic synthetic dyes as effluents. In recent years, nanomaterials have become attractive choice for eco-friendly removal of organic dyestuff. Accordingly, this article reports synthesis and characterization of biocomposite wherein copolymer of polyaniline (PANI) and Polypyrrole (PPY) was grafted onto hydroxyethyl cellulose (HEC). Further, adsorption properties of as-prepared composite were evaluated using textile dyes Rhodamine B (RhB) and methyl Orange (MO)- as model adsorbate. The characterization of novel biocomposite (HEC/PANI-PPy) was carried out using Fourier Transform Infrared (FT-IR), Brunauer-Emmett-Teller analyzer (BET), Scanning Electron Microscope (SEM), and powder X-ray diffraction (XRD). The operational parameters such as dye initial concentration, adsorbent amount, pH and contact time were also studied to evaluate the efficiency level of the prepared biocomposite. Interestingly, the composite-mediated adsorption of RhB and MO followed pseudo-second order and the Langmuir isotherm. It is found that the adsorption capacity HEC/PANI-PPy is 30.06 and 29.3 for RhB and MO respectively. Thus, HEC/PANI-PPy is an inexpensive and highly efficient adsorbent that could be employed for could be employed for the separation and removal of toxic organic dyes from polluted textile effluents. [ABSTRACT FROM AUTHOR]

The development of the paper industry has led to the discharge of a large amount of papermaking waste liquid containing lignosulfonate. These lignin black liquids cause a lot of pollution in nature, which runs counter to the current environmental protection strategy under the global goal. Through the development and use of lignosulfonate in papermaking waste liquid to increase the utilization of harmful substances in waste liquid, we aim to promote waste liquid treatment and reduce environmental pollution. This paper proposes a new strategy to synthesize novel glue-free biocomposites with high-performance interfacial compatibility from papermaking by-product sodium lignosulfonate/chitosan (L/C) and waste bamboo. This L/C bamboo biocomposite material has good mechanical properties and durability, low formaldehyde emissions, a high recovery rate, meets the requirements of wood-based panels, and reduces environmental pollution. This method is low in cost, has the potential for large-scale production, and can effectively reduce the environmental pollution of the paper industry, promoting the recycling of biomass and helping the future manufacture of glue-free panels, which can be widely used in the preparation of bookcase, furniture, floor and so on.

The growing concern about environmental pollution has generated an increased demand for biobased and biodegradable materials intended particularly for the packaging sector. Thus, this study focuses on the effect of two different cellulosic reinforcements and plasticized poly(3-hydroxybutyrate) (PHB) on the properties of poly(lactic acid) (PLA). The cellulose fibers containing lignin (CFw) were isolated from wood waste by mechanical treatment, while the ones without lignin (CF) were obtained from pure cellulose by acid hydrolysis. The biocomposites were prepared by means of a melt compounding-masterbatch technique for the better dispersion of additives. The effect of the presence or absence of lignin and of the size of the cellulosic fibers on the properties of PLA and PLA/PHB was emphasized by using in situ X-ray diffraction, polarized optical microscopy, atomic force microscopy, and mechanical and thermal analyses. An improvement of the mechanical properties of PLA and PLA/PHB was achieved in the presence of CF fibers due to their smaller size, while CFw fibers promoted an increased thermal stability of PLA/PHB, owing to the presence of lignin. The overall thermal and mechanical results show the great potential of using cheap cellulose fibers from wood waste to obtain PLA/PHB-based materials for packaging applications as an alternative to using fossil based materials. In addition, in situ X-ray diffraction analysis over a large temperature range has proven to be a useful technique to better understand changes in the crystal structure of complex biomaterials. [ABSTRACT FROM AUTHOR]

Silica is a popular filler, but in epoxidized natural rubber, can act as a cross-linking agent. Unfortunately, a high amount of silica is necessary to obtain satisfactory tensile strength. Moreover, a high amount of silica in ENR/silica hybrids is associated with low elongation at break. In our paper, we propose natural phenolic compounds, including quercetin, tannic acid, and gallic acid as natural and safe additional crosslinkers dedicated to ENR/silica hybrids to obtain bio-elastomers with improved mechanical properties. Therefore, toxic crosslinkers, such as peroxides or harmful accelerators can be eliminated. The impact of selected natural phenolic compounds on crosslinking effect, mechanical properties, color, and chemical structure of ENR/silica composite have been analyzed. The obtained results indicated that only 3 phr of selected natural phenolic compounds is able to improve crosslinking effect as well as mechanical properties of ENR/silica hybrids. Moreover, some of the prepared materials tend to regain mechanical properties after reprocessing. Such materials containing only natural and safe ingredients have a chance of becoming novel elastomeric biomaterials dedicated to biomedical applications. [ABSTRACT FROM AUTHOR]

The emerging concepts of sustainable textiles and controlled production strategy demands ideally zero emissions of contaminants into the aquatic environment. However, the currently in-practiced conventional processes in textiles dispose of a number of contaminants especially super toxic synthetic dyes as effluents. In recent years, nanomaterials have become attractive choice for eco-friendly removal of organic dyestuff. Accordingly, this article reports synthesis and characterization of biocomposite wherein copolymer of polyaniline (PANI) and Polypyrrole (PPY) was grafted onto hydroxyethyl cellulose (HEC). Further, adsorption properties of as-prepared composite were evaluated using textile dyes Rhodamine B (RhB) and methyl Orange (MO)- as model adsorbate. The characterization of novel biocomposite (HEC/PANI-PPy) was carried out using Fourier Transform Infrared (FT-IR), Brunauer-Emmett-Teller analyzer (BET), Scanning Electron Microscope (SEM), and powder X-ray diffraction (XRD). The operational parameters such as dye initial concentration, adsorbent amount, pH and contact time were also studied to evaluate the efficiency level of the prepared biocomposite. Interestingly, the composite-mediated adsorption of RhB and MO followed pseudo-second order and the Langmuir isotherm. It is found that the adsorption capacity HEC/PANI-PPy is 30.06 and 29.3 for RhB and MO respectively. Thus, HEC/PANI-PPy is an inexpensive and highly efficient adsorbent that could be employed for could be employed for the separation and removal of toxic organic dyes from polluted textile effluents.

The growing concern about environmental pollution has generated an increased demand for biobased and biodegradable materials intended particularly for the packaging sector. Thus, this study focuses on the effect of two different cellulosic reinforcements and plasticized poly(3-hydroxybutyrate) (PHB) on the properties of poly(lactic acid) (PLA). The cellulose fibers containing lignin (CFw) were isolated from wood waste by mechanical treatment, while the ones without lignin (CF) were obtained from pure cellulose by acid hydrolysis. The biocomposites were prepared by means of a melt compounding-masterbatch technique for the better dispersion of additives. The effect of the presence or absence of lignin and of the size of the cellulosic fibers on the properties of PLA and PLA/PHB was emphasized by using in situ X-ray diffraction, polarized optical microscopy, atomic force microscopy, and mechanical and thermal analyses. An improvement of the mechanical properties of PLA and PLA/PHB was achieved in the presence of CF fibers due to their smaller size, while CFw fibers promoted an increased thermal stability of PLA/PHB, owing to the presence of lignin. The overall thermal and mechanical results show the great potential of using cheap cellulose fibers from wood waste to obtain PLA/PHB-based materials for packaging applications as an alternative to using fossil based materials. In addition, in situ X-ray diffraction analysis over a large temperature range has proven to be a useful technique to better understand changes in the crystal structure of complex biomaterials.

Silica is a popular filler, but in epoxidized natural rubber, can act as a cross-linking agent. Unfortunately, a high amount of silica is necessary to obtain satisfactory tensile strength. Moreover, a high amount of silica in ENR/silica hybrids is associated with low elongation at break. In our paper, we propose natural phenolic compounds, including quercetin, tannic acid, and gallic acid as natural and safe additional crosslinkers dedicated to ENR/silica hybrids to obtain bio-elastomers with improved mechanical properties. Therefore, toxic crosslinkers, such as peroxides or harmful accelerators can be eliminated. The impact of selected natural phenolic compounds on crosslinking effect, mechanical properties, color, and chemical structure of ENR/silica composite have been analyzed. The obtained results indicated that only 3 phr of selected natural phenolic compounds is able to improve crosslinking effect as well as mechanical properties of ENR/silica hybrids. Moreover, some of the prepared materials tend to regain mechanical properties after reprocessing. Such materials containing only natural and safe ingredients have a chance of becoming novel elastomeric biomaterials dedicated to biomedical applications.