Search

With the worldwide rollout of the 5G communication network and 6G around the corner, we have witnessed the rapid development of the Internet of Things (IoT) technology, enabling big data and digital transformation in various fields [...]

In recent years, we have witnessed the revolutionary innovation and flourishing advancement of the Internet of things (IoT), which will maintain a strong momentum even more with the gradual rollout of the fifth generation (5G) wireless network and the rapid development of personal healthcare electronics [...]

This paper proposed a high-performance magnetic-coupled nonlinear electromagnetic generator (MNL-EMG). A high-permeability iron core is incorporated to the coil. The strong coupling between the iron core and the vibrating magnets lead to significantly improved output power and a broadened operating bandwidth. The magnetic force of the iron core to the permanent magnets and the magnetic flux density inside the iron core are simulated, and the dimension parameters of the MNL-EMG are optimized. Under acceleration of 1.5 g, the MNL-EMG can maintain high output performance in a wide frequency range of 17~30 Hz, which is 4.3 times wider than that of linear electromagnetic generator (EMG) without an iron core. The maximum output power of MNL-EMG reaches 174 mW under the optimal load of 35 Ω, which is higher than those of most vibration generators with frequency less than 30 Hz. The maximum 360 parallel-connected LEDs were successfully lit by the prototype. Moreover, the prototype has an excellent charging performance such that a 1.2 V, 900 mAh Ni-MH battery was charged from 0.95 V to 0.98 V in 240 s. Both the simulation and experiments verify that the proposed bistable EMG device based on magnetic coupling has advantages of wide operating bandwidth and high output power, which could be sufficient to power micro electronic devices.

This paper reports the design, micromachining and characterization of an array of electromagnetic energy harvesters (EHs) with multiple frequency peaks. The authors present the combination of three multi-modal spring-mass structures so as to realize at least nine resonant peaks within a single microelectromechanical systems (MEMS) chip. It is assembled with permanent magnet to show an electromagnetic-based energy harvesting capability. This is the first demonstration of multi-frequency MEMS EH existing with more than three resonant peaks within a limited frequency range of 189 to 662 Hz. It provides a more effective approach to harvest energy from the vibration sources of multiple frequency peaks.

This paper proposes an impact-based micro piezoelectric energy harvesting system (PEHS) working with the frequency up-conversion mechanism. The PEHS consists of a high-frequency straight piezoelectric cantilever (SPC), a low-frequency S-shaped stainless-steel cantilever (SSC), and supporting frames. During the vibration, the frequency up-conversion behavior is realized through the impact between the bottom low-frequency cantilever and the top high-frequency cantilever. The SPC used in the system is fabricated using a new micro electromechanical system (MEMS) fabrication process for a piezoelectric thick film on silicon substrate. The output performances of the single SPC and the PEHS under different excitation accelerations are tested. In the experiment, the normalized power density of the PEHS is 0.216 μW·g−1·Hz−1·cm−3 at 0.3 g acceleration, which is 34 times higher than that of the SPC at the same acceleration level of 0.3 g. The PEHS can improve the output power under the low frequency and low acceleration scenario.

A hybrid energy harvester is presented in this paper to harvest energy from water flow motion and temperature difference in an irrigating pipe at the same time. The harvester is based on the integration of thermoelectric and electromagnetic mechanisms. To harvest the water flow motion, a turbine fan with magnets that are attached on the blades is placed inside of the water pipe. Multiple coils turn the water flow energy into electricity with the rotation of the turbine. The thermoelectric generators (TEGs) are attached around the pipe, so as to harvest energy due to temperature difference. For a maximum temperature difference of 55 °C (hot side 80 °C and room temperature 25 °C), twelve serial-connected TEGs can generate voltage up to 0.346 V. Under a load resistance of 20 Ώ, the power output of 1.264 mW can be achieved. For a maximum water flow rate of 49.9 L/min, the electromagnetic generator (EMG) can produce an open circuit voltage of 0.911 V. The EMG can be potentially used as a water flow meter due to the linear relationship between water flow rate and output voltage. Under the joint action of TEG and EMG, the maximum terminal voltage for TEG is 66 mV and for EMG is 241 mV at load resistances of 10 and 100 Ώ, respectively, resulting in a corresponding power output of 0.435 and 0.584 mW.

This paper presents a triple-finger gripper driven by a piezoceramic (PZT) transducer for multi-target micromanipulation. The gripper consists of three fingers assembled on adjustable pedestals with flexible hinges for a large adjustable range. Each finger has a PZT actuator, an amplifying structure, and a changeable end effector. The moving trajectories of single and double fingers were calculated and finite element analyses were performed to verify the reliability of the structures. In the gripping experiment, various end effectors of the fingers such as tungsten probes and fibers were tested, and different micro-objects such as glass hollow spheres and iron spheres with diameters ranging from 10 to 800 μm were picked and released. The output resolution is 145 nm/V, and the driven displacement range of the gripper is 43.4 μm. The PZT actuated triple-finger gripper has superior adaptability, high efficiency, and a low cost.