Search

The oxidation resistance of TiAl alloys is crucial for their commercial application. In this paper, a cyclic oxidation test with stable air circulation was designed to investigate the cyclic oxidation behavior of the TNM alloy and 4822 alloy at 800 °C and to analyze the phase, morphology, and thermal stress evolution of the oxide layer. The oxidation weight gain curves of both alloys are found to be in parabolic form, and the oxidation reaction orders of the TNM alloy and 4822 alloy are 2.374 and 1.838, respectively. The Nb and Mo elements enhance the antioxidant performance of the TNM alloy by inhibiting the dissolution and diffusion of oxygen, Ti, and Al atoms in the TiAl alloy. The thermal stress evolution of the two alloys during the heating and cooling phases of the cyclic oxidation process are calculated separately, and it is found that the thermal stresses in the TNM alloy are smaller than those in the 4822 alloy, while the maximum thermal stresses appear at the oxide/substrate interface rather than inside the oxide scale, which quantitatively explains the oxidation peeling resistance of the two alloys.

The surface of hot stamping steel is severely oxidized during heating, holding, and transfer from the heating furnace to the stamping die in the production of traditional automotive parts. Coating-free hot stamping steel with Cr and Si elements exhibits excellent oxidation resistance during hot stamping without the protection of a surface coating. This paper investigates the oxidation behavior of three types of hot stamping steel at 800–1200 °C. The results show that although Cr-Si hot stamping steel performs excellently short-term (≤7.5 min) for oxidation resistance, its long-term (≥15 min) or high-temperature (≥1100 °C) oxidation resistance is much lower than that of the conventional hot stamping steel 22MnB5, affecting the production and surface quality control of the new coating-free Cr-Si hot stamping steel. By analyzing the oxidation kinetics and characterizing the structure of oxide layers in hot stamping steel, it was found that the structural change in the Cr and Si element enrichment layer between the oxide scale and the substrate varied in oxidation performance at different temperatures. When the oxidation temperature was below 1000 °C, the solid Cr and Si enrichment layer acted as a barrier to prevent the diffusion of Fe ions. When the oxidation temperature exceeded 1100 °C, the molten Cr and Si enrichment layer effectively adapted to the substrate and avoided blistering. Meanwhile, Fe2SiO4 penetrated the Fe oxide layer along the grain boundary and became a rapidly diffusing channel of Fe ions, contributing to a significant increase in the oxidation rate.

Cord steel is used for making tire frames and wire saws for cutting silicon wafers. The diameter of mainstream cutting wire has been developed to be lower than 100 μm. The size and deformation ability of inclusions are very important to the wire breaking rate of cord steel during the drawing process. In order to improve the deformation ability of the inclusions in cord steel, alkali metal oxide was added into the molten steel to improve the inclusions in the steel so as to obtain good, plastic, low-melting-point inclusions. Mass fractions of 0.3%, 0.5% and 1.0% K2CO3, Na2CO3 and B2O3 were added into cord steel, which were melted in 10 furnaces (including 0% alkali metal oxides, mass fractions of 0.3%/0.5%/1.0% K2CO3, Na2CO3 and B2O3). The morphology and composition of inclusions were observed by SEM-EDS. Factsage phase diagram calculations and experimental results show that, with the increase in Na2CO3 content in cord steel, the aluminum content in the inclusions gradually decreased. When the mass fraction of Na2CO3 was 0.5% per ton, most of the inclusions in the steel fell in the low melting point region (less than 1300 °C). With the increase in K2CO3 content in cord steel, the silicon content in the inclusions decreased gradually. When the mass fraction of K2CO3 was 0.5% per ton, most of the inclusions in the steel fell in the low melting point region. The deformation ability of the inclusions added with 0.5% Na2CO3 in the steel during forging was better than that of the inclusions added with 0.5% K2CO3. After adding B2O3, the inclusions in the steel were SiO2-MnO-Al2O3 inclusions or inclusions with SiO2-MnO-Al2O3 as the core and BN wrapped around. Boron could not be dissolved into the inclusions for plastic modification.

In this paper, we present the effect of austenitizing temperature on the work hardening behavior of air-hardening steel LH800 by evaluating the influence of austenitizing temperature on microstructure evolution and mechanical properties, using Hollomon, Differential Crussard–Jaoul (DC-J), and Modified C-J (MC-J) work hardening models. The results reveal that with an increase in austenitizing temperature, there is an increase in the percentage of martensite, along with an increase in the strength and hardness of the LH800 steel; on the other hand, there is a decrease in the plasticity. Austenitized at 825 °C, LH800 steel exhibits its highest strength and good plasticity, with a tensile strength of 897 MPa and an elongation of 13.6%. The comparison between the three strain hardening models revealed that the Hollomon model was the finest fit for the experimental data utilized and could illustrate the work hardening behavior of LH800 steel most suitably. This model manifests a two-stage work hardening mechanism; the first stage is related to the plastic deformation of ferrite phase, while the second stage deals with the co-deformation of ferrite and martensite/bainite phase. As austenitizing temperature increases, the work hardening ability of LH800 steel diminishes at each stage, the transition strain decreases, and the plastic deformation of martensite starts earlier.

In this study, the effect of the hot-cold rolling process on the evolution of the microstructure, texture and magnetic properties of strip-cast non-oriented electrical steel was investigated by introducing hot rolling with different reductions. The results indicate that hot rolling with an appropriate reduction, such as the 20% used in this study, increases the shear bands and {100} deformed microstructure in the cold roll sheet. As a result, in our study, enhanced η and Cube recrystallization texture and the improved magnetic induction were obtained. However, hot rolling with excessive reduction (36–52%) decreased the shear bands and increased the α-oriented deformation microstructure with low stored energy. It enhanced the α recrystallization texture and weakened the η texture, resulting in a decrease in the magnetic induction. In addition, hot rolling promoted the precipitation of supersaturated solid solution elements in the as-cast strip, thereby affecting the subsequent microstructure evolution and the optimization of its magnetic properties.

In order to investigate the dynamic mechanical behavior of TiAl alloys and promote their application in the aerospace industry, uniaxial compression of Ti-44Al-4Nb-1.5Mo-0.007Y (at %) alloy was conducted at a temperature range from 25 to 400 °C with a strain rate of 2000 s‒1. Twinning is found to be the dominating deformation mechanism of the γ phase at all temperatures, and the addition of Nb and Mo has a chemical impact on the alloy and reduces the stacking fault energy of the γ phase. The decreased stacking fault energy increases the twinnability; thus, the deformation is dominated by twinning, which increases the dynamic strength of the alloy. With the temperature increasing from 25 to 400 °C, the average spacing of twins in the γ phase increases from 32.4 ± 2.9 to 88.1 ± 9.2 nm. The increased temperature impedes the continuous movement of partial dislocations and finally results in an increased twin spacing in the γ phase.

Multiple strengthening methods, such as high dislocation density, high twin density, small grain size, and metastable austenite phase can give high strength to ultra-high strength steels (UHSSs). However, the high strength of UHSSs often results in a greater tendency for springback when applied in manufacturing vehicle components. In the present study, two types of UHSSs, dual-phase (DP) steel and quenching and partitioning (QP) steel are investigated to study the springback behavior during the bending process. Results indicated that both the strain heterogeneity and the transformation of retained austenite impacted the springback behavior. The springback angle of the DP steel increased with the increase in bending angle, which was caused by the increasing degree of strain heterogeneity. However, the springback angle of the QP steel decreased to a 14.75° when QP specimens were strained at a 104° bending angle due to the inhibiting effect of the phase transformation. This indicated that there was preferential phase transformation in the thickness direction in the retained austenite of the outer and inner zones. The phase transformation caused low strain heterogeneity, which resulted in a lower tendency for springback. The results suggested that QP steel could possess lower springback at a proper bending angle.