Search

In the present work, a series of high-entropy alloys based on refractory metals Hf, Nb, Ta, Ti, V, and Zr with various compositions have been systematically investigated. Our study revealed that a bcc single-phase solid solution of a Hf-Nb-Ta-Ti-V-Zr system is thermodynamically stable only at high temperatures above 1000 °C. At lower temperatures, the phase separation into disordered bcc phases with slightly different chemical compositions occurs. Despite the phase separation, a single-phase random solid solution can be saved at room temperature as a metastable phase by rapid cooling of the sample from high temperature. The microstructure of a single-phase metastable random solid solution was characterized and compared with the microstructure of the as-cast state. Furthermore, the mechanical properties of annealed and as-cast alloys were compared. Interestingly, both states exhibit comparable mechanical properties. It indicates that from the point of view of practical applications, a mechanical mixture of disordered bcc solutions is as good as single-phase random solid solution.

A detailed characterization of phase transformations in the heat-treated commercial 7075 aluminum alloys without/with low Sc–Zr addition was carried out. Mechanical and electrical properties, thermal and corrosion behavior were compared to the microstructure development. The eutectic phase consists of four parts: MgZn2 phase, Al2CuMg phase (S-phase), Al2Zn3Mg3 phase (T-phase), and primary λ-Al(Mn,Fe,Si) phase. Strengthening during non-isothermal (isochronal) annealing is caused by a combination of formation of the GP zones, η’-phase, T-phase and co-presence of the primary and secondary Al3(Sc,Zr)-phase particles. Positive influence on corrosion properties is owing to the addition of Sc–Zr. Positron annihilation showed an evolution of solute Zn,Mg-(co-)clusters into (precursors of) the GP zones in the course of natural ageing. The concentration of the (co-)clusters is slightly negatively affected by the low Sc–Zr addition. A combination of both precipitation sequences of the Al–Zn–Mg–Cu-based system was observed. The apparent activation energy values for dissolution/formation of the clusters/GP zones and for formation of the metastable η’-phase, stable T-phase and stable η-phase were calculated.

Ti15Mo metastable beta Ti alloy was solution treated and subsequently deformed by high-pressure torsion (HPT). HPT-deformed and benchmark non-deformed solution-treated materials were annealed at 400 °C and 500 °C in order to investigate the effect of UFG microstructure on the α-phase precipitation. Phase evolution was examined using laboratory X-ray diffraction (XRD) and by high-energy synchrotron X-ray diffraction (HEXRD), which provided more accurate measurements. Microstructure was observed by scanning electron microscopy (SEM) and microhardness was measured for all conditions. HPT deformation was found to significantly enhance the α phase precipitation due the introduction of lattice defects such as dislocations or grain boundaries, which act as preferential nucleation sites. Moreover, in HPT-deformed material, α precipitates are small and equiaxed, contrary to the α lamellae in the non-deformed material. ω phase formation is suppressed due to massive α precipitation and consequent element partitioning. Despite that, HPT-deformed material after ageing exhibits the high microhardness exceeding 450 HV.

Tungsten-based materials are the prime candidate plasma-facing materials for future fusion reactors, such as DEMO. Spark plasma sintering is a prospective fabrication technology with several advantageous features. The concurrent application of electric current, temperature and pressure enhances the sintering process, allowing for lower temperatures and shorter sintering times than traditional powder metallurgy processes. This in turn helps to avoid excessive grain growth and phase segregation in W-alloys. This study is focused on several factors that may influence the homogeneity of the sintered compacts—namely the diffusion of carbon from the graphite die, purity of the powder and sintering conditions. The following characteristics of spark plasma-sintered tungsten compacts were studied: composition (especially carbon and oxygen content), porosity, mechanical properties (hardness and fracture strength), and thermal diffusivity. The effects of the abovementioned processing factors were quantified, and local variations of selected properties were assessed.

W alloys are currently widely studied materials for their potential application in future fusion reactors. In the presented study, we report on the preparation and properties of mechanically alloyed W-Ti powders compacted by pulsed electric current sintering. Four different powder compositions of W-(3%–7%)Ti with Hf or HfC were prepared. The alloys’ structure contains only high-melting-point phases, namely the W-Ti matrix, complex carbide (Ti,W,Hf)C and HfO2 particle dispersion; Ti in the form of a separate phase is not present. The bending strength of the alloys depends on the amount of Ti added. The addition of 3 wt. % Ti led to an increase whereas 7 wt. % Ti led to a major decrease in strength when compared to unalloyed tungsten sintered at similar conditions. The addition of Ti significantly lowered the room-temperature thermal conductivity of all prepared materials. However, unlike pure tungsten, the conductivity of the prepared alloys increased with the temperature. Thus, the thermal conductivity of the alloys at 1300 °C approached the value of the unalloyed tungsten.