Search

To improve the strength of the metal while maintaining good plasticity, helical fibers are added to the metal matrix. How to form helical fiber and control its parameters in the preparation process are urgent problems to be solved in the study of helical fiber-reinforced metal matrix composites. In this paper, the continuous casting process of helical fiber-reinforced metal matrix composites was proposed. To reduce the difficulty of the experiment, the formation process of helical fiber on metal matrix and the relationship between the continuous casting process parameters and helical shape fiber parameters were studied by preparing helical carbon fiber-reinforced lead matrix composites with a low-melting-point metal matrix. The results show that this process can produce helical fiber-reinforced metal matrix composite stably and continuously, and the helical shape parameters of the composite can be controlled by changing the process parameters of continuous casting. To further improve the practical application of this process, helical carbon fiber-reinforced aluminum matrix composites were prepared. The test result in terms of mechanical property shows that the tensile strength and elongation of the composite were improved. This indicates that the reinforced phase of the helical structure of the metal matrix composite has higher strength and toughness compared with the matrix metal.

The continuous tube-rolling method has been widely used to manufacture high-quality seamless pipes and tubes. However, the analytical model for determining the roll pitch diameter in three-roll continuous retained mandrel rolling from first principles has not yet been presented, which has, thus, hindered the development of rolling control technology in tube manufacturing. In this work, a new analytical model has been established from the force–equilibrium principles. The modelling has taken the tube-roll contact geometry, roll pressure, mandrel pull forces, inter-stand tensions, and friction coefficients into account for its formulations. Seen from the experimental results of the rolling at the plant, the maximum deviation of the predicted projected contact area is less than 6% and the maximum deviation of the calculated roll speed from the satisfactory data in field operation is less than 3.9%. The proposed model has enabled the influence of the friction coefficients on the roll pitch diameter to be quantified in theoretical analysis, and it was found that the changing amplitude of the theoretical roll pitch diameter corresponding to the commonly used data range of the friction coefficients can be above 9%. Having overcome the shortcomings of the empirical model, this model has the required prediction accuracy and flexibility for being applied to flexible tube rolling. By building the key algorithms around physical models, this modelling has advanced not only the rolling control at the plant, but also our scientific understanding of the mechanics of the continuous tube-rolling process.

In order to promote the industrialization of the large deformation technology of carbon fiber composites, this paper studies a new method of forming of helical carbon fiber reinforced aluminum matrix composite. The purpose is to solve the problem of large deformation of carbon fiber with low elongation and metal matrix with high elongation. By introducing carbon fiber with helical space structure into the aluminum matrix, the helical carbon fiber reinforced aluminum matrix composites were prepared and the subsequent drawing deformation was carried out. Here we systematically studied the large plastic deformation behavior of helical carbon fiber reinforced aluminum matrix composite via a combination of numerical simulations and experiments, and analyzed the deformation law and stress of helical carbon fiber in the deformation process. We found that the plastic deformation of the composite causes local stress concentration around the helical carbon fiber, and the helical carbon fiber will move synchronously with the aluminum matrix during the deformation, and receive the pressure from the aluminum matrix. Second, the best process parameters obtained from the simulation, that is, the drawing die angle α = 7°, when five-pass drawing experiments were carried out, the total deformation reached 58%, and the average elongation of a single pass was 18.9%. The experimental show carbon fiber reinforced aluminum matrix composite with helical space structure can achieve large deformation and high strength. The experimental and simulation are in general agreement, which verifies the correctness of the carbon fiber helical structure model.

The coefficients of thermal expansion (CTE) and thermal conductivity (TC) are important for heat sink applications, as they can minimize stress between heat sink substrates and chips and prevent failure from thermal accumulation in electronics. We investigated the interface behavior and manufacturing of diamond/Cu composites and found that they have much lower TCs than copper due to their low densities. Most defects, such as cavities, form around diamond particles, substantially decreasing the high TC of diamond reinforcements. However, the measurement results for the Cu-coated diamond/Cu composites are unsatisfactory because the nanosized copper layer on the diamond surface grew and spheroidized at elevated sintering temperatures. Realizing ideal interfacial bonding between a copper matrix and diamond particles is difficult. The TC of the 40 vol.% Ti-coated diamond/Cu composite is 475.01 W m−1 K−1, much higher than that of diamond/Cu and Cu-coated diamond/Cu composites under equivalent manufacturing conditions. The minimally grown titanium layer retained its nanosized and was consistent with the sintering temperature. Depositing a nanosized titanium layer on a diamond surface will strengthen interfacial bonding through interface reactions among the copper matrix, nanosized titanium layer and diamond particles, reducing the interfacial thermal resistance and exploiting the high TC of diamond particles, even if defects from powder metallurgy remain. These results provide an important experimental and theoretical basis for manufacturing diamond/Cu composites for heat sink applications.

Carbon fiber is mainly distributed in the shape of short fibers and continuous fiber bundles as the reinforcing phase in metal matrix composites, and it is seldom studied as braided rope shaped to reinforce the matrix. For this paper, the pretreatment and the surface metallization of the carbon fiber braided rope were studied. Besides, the casting experiments of aluminum-based carbon fiber braided rope composites were performed without external pressure. XPS analysis shows that the surface of the carbon fiber braided rope treated with ultrasonic degumming contains many hydrophilic oxygen-containing functional groups C-OH, C=O, COOH, etc., which can effectively improve the wettability between the carbon fiber braided rope and the aluminum matrix. SEM, EDS, and XRD were used to analyze the micromorphology and structure of the copper plating on the surface of carbon fiber braided ropes obtained from different pH plating solutions. When pH is 12, a continuous, uniform, and dense layer was formed on the surface of carbon fiber braided ropes. In addition, copper coating can effectively inhibit the formation of Al4C3 brittle phase. Finally, the mechanical properties results indicated that the tensile strength of the carbon fiber bundle and carbon fiber rope reinforced composite materials were 69 MPa and 83 MPa, respectively, indicating that the reinforcing effect of the carbon fiber rope is better than that of the carbon fiber bundle.