Search

Due to the classification of Co as a CMR (carcinogenic, mutagenic, toxic to reproduction) as well as the classification of both Co and WC as CRM (critical raw materials) more and more research is being carried out to investigate possible substitutes for WC-Co hardmetals. To directly compare their microstructure as well as mechanical and thermophysical properties, five very different hardmetals were investigated. For this purpose, the compositions WC-Co, WC-FeNiMn, WC-HEA, NbC-Co and HEC-Co were selected in order to investigate alternative binders for cobalt as well as different alternative hard phases for WC. The results of the hardness measurements showed that for the hardmetals with alternative binders (WC-FeNiMn and WC-HEA) hardness values of 1327 HV10 and 1299 HV10 comparable to WC-Co with 1323 HV10 can be achieved. When WC is replaced by HEC as the hard phase, a significantly higher hardness of 1543 HV10 can be obtained, demonstrating the great potential of high-entropy carbides. Furthermore, the hot hardness measurements between RT and 900 °C showed significantly higher values (up to approx. 290 HV10) for the WC-HEA and HEC-Co hardmetals compared to those of WC-Co. However, the fracture toughness of the alternative hardmetals was lower compared to that of conventional WC-Co hardmetals. In terms of thermophysical properties, the results of the hardmetals with alternative binders were close to those of WC-Co. Thus, it can be shown that it is possible to produce alternative hardmetals with comparable properties to WC-Co and that with further optimization they show great potential to replace WC-Co in the near future.

Cermets are composites of a TiCN hard phase and a metal binder, typically a mixture of Co and Ni. They offer excellent combinations of hardness and fracture toughness as well as bending strength. Due to the current classification of both Co and Ni as CRM as well as CMR there is interest that their use shall be limited and their amount within cermets reduced. Within this study, a novel high entropy alloy-based metal binder system, comprising only elements that are not strong oxide or carbide formers is investigated with regard to their mechanical and microstructural properties they offer in TiCN-based cermets. Within the investigated equimolar MnFeCoNiCu composition, small Cu precipitations are found after sintering. Due to this, the Cu content was systematically reduced, and the maximal solubility estimated at which still a full solid solution occurs. With an optimized Cu content, dense cermets with a single FCC binder phase and with hardness values of up to 1213 HV30 and fracture toughness values of 14.8 MPa·m1/2 could be achieved.

In situ composite manufacture is an approach to improve interfacial adhesion between matrix and reinforcements, in which reinforcements are synthesized along composite processing itself. In situ powder metallurgy route, in particular, offers alternatives to some shortcomings found in other techniques. This work aims not only to review the state of the art on metal matrix composites (MMCs)—including cermets—obtained in situ by powder metallurgy, but also to dissect key aspects related to the development of such materials in order to establish theoretical criteria for decision making before and along experiments. Aspects regarding the design, raw material selection, and processing of such composites were observed and divided between concept, intrinsic, and extrinsic parameters. That way, by means of material databases and computational thermodynamics applied to examples of the reviewed literature, we aim at providing tools in both conducting leaner experiments and richer discussion in this field.

In this article, we analyse five types of coatings, in terms of their microstructure, hardness, porosity, and wear resistance, in the as-sprayed state. The coatings are WC-based (WC-FeCrAl, WC-WB-Co, and WC-NiMoCrFeCo), alloy-based (Co-MoCrSi), or nanoWC coating-based (nanoWC-CoCr). Two tests were applied to assess the wear resistance of the coatings: a dry-pot wear test with two impact angles and an abrasive test using an abrasive cloth with two grit sizes. Porosity was determined by image analysis. Vickers impression was performed on cross-sections of the coatings, in order to determine their indentation fracture toughness. The highest hardness of the tested coatings was recorded for the nanoWC coating, followed by the rest of the WC-based coatings; meanwhile, the lowest hardness was recorded for the alloy coating. Minimal porosity was achieved by the alloy coating, due to its different nature and the absence of hard particles with a higher melting point. The NanoWC coating and other WC-based coatings had a higher porosity; however, porosity did not exceed 1% for each coating. The best wear resistance was achieved by the nanoWC coating, followed by the other WC-based coatings, with the lowest obtained by the alloy coating. The same tendency was recorded when determining the indentation fracture toughness. From a microscopic point of view, the structure of the evaluated coatings is not compact; nevertheless, their properties are excellent, and they act as compact coatings under load.

TiB2-Cu cermets with various volume fractions of copper (from 3 to 30 vol. %) were produced via liquid phase sintering at the temperature range 1100–1200 °C in vacuum using spark plasma sintering (SPS) technique. Full densification could not be achieved as the consequence of poor wettability and vaporizing Cu. The quantitative Rietveld analysis indicated that insignificant reduction in Cu content occurred only in sample with initially 3 vol. % of Cu, but then densification was negligible. The relative density improved along with increasing volume content of Cu (10–20 vol. %), but then predominant amount of Cu introduced was reduced as the effect of vaporization or swelling, which caused that pellet with intended 20 or 30 vol. % of Cu contained respectively only 6 or 17 vol. % after sintering. Moreover, Cu droplets were released from the die at the temperature of 1000–1030 °C near the Cu melting point. The effect of vaporization was successfully reduced by increased heating rate and when isothermal annealing process was skipped, however, it could not be entirely eliminated. The experimental results on Cu vaporization are confronted with parameters that are commonly considered in the production of cermets, such as oxidation, wettability, contact angle and viscosity as well as their impact on densification.

Ceramic and metal composites, known also as cermets, may considerably improve many material properties with regards to that of initial components. Hence, cermets are frequently applied in many technological fields. Among many processes which can be employed for cermet manufacturing, thermal spraying is one of the most frequently used. Conventional plasma spraying of powders is a popular and cost-effective manufacturing process. One of its most recent innovations, called solution precursor plasma spraying (SPPS), is an emerging coating deposition method which uses homogeneously mixed solution precursors as a feedstock. The technique enables a single-step deposition avoiding the powder preparation procedures. The nanostructured coatings developed by SPPS increasingly find a place in the field of surface engineering. The present review shows the recent progress in the fabrication of cermets using SPPS. The influence of starting solution precursors, such as their chemistry, concentration, and solvents used, to the micro-structural characteristics of cermet coatings is discussed. The effect of the operational plasma spray process parameters such as solution injection mode to the deposition process and coatings’ microstructure is also presented. Moreover, the advantages of the SPPS process and its drawbacks compared to the conventional powder plasma spraying process are discussed. Finally, some applications of SPPS cermet coatings are presented to understand the potential of the process.

The paper is focused on investigating the quality of two grades of thermally sprayed coatings deposited by high-velocity oxygen fuel (HVOF) technology. One grade contains WC hard particles in an environmentally progressive Ni- and Co-free FeCrAl matrix, while the second coating contains WC and WB hard particles in a cobalt matrix. The aim of the experimental work was to determine the effect of thermal cyclic loading on the coatings’ resistance to adhesive, abrasive and erosive wear. Abrasive wear was evaluated using abrasive cloth of two grit sizes, and erosive wear was evaluated by a dry-pot wear test in a pin mill at two sample angles. Adhesion wear resistance of the coatings was determined by a sliding wear test under dry friction conditions and in a 1 mol water solution of NaCl. Corrosion resistance of the coatings was evaluated using potentiodynamic polarization tests. Metallographic cross-sections were used for measurement of the microhardness and thickness and for line energy-dispersive X-ray (EDX) analysis. The tests proved the excellent resistance of both coatings against adhesive, abrasive, and erosive wear, as well as the ability of the WC-WB-Co coating to withstand alternating temperatures of up to 600 °C. The “green carbide” coating (WC-FeCrAl) can be recommended as an environmentally friendly replacement for Ni- and Co-containing coatings, but its operating temperature is strictly limited to 500 °C in air.