Search

In the present study, PHB film was prepared by thermo-compression molding and PHB nanofibers mat was produced through electrospinning process. The nanofibers morphology was confirmed by SEM. The film and nanofibers crystallinity degree was estimated by different methods. FTIR and WAXD indicated that PHB film is more crystalline than PHB nanofibers. However, DSC analysis suggested that a PHB nanofibers phase change might occur while the temperature rises. SAXS indicated that PHB film and nanofibers have low electron density contrast between the alternating crystalline and amorphous layers. The influence of nanofiber morphology on the mechanical, surface and thermal properties was also shown in TG analysis, tensile tests and contact angle measurements.

Bamboo is an alternative sustainable material for use in product design and has been incorporated into the concepts of eco-design. Here, we investigated the mechanical properties and morphologies of low density polyethylene (LDPE)/bamboo flour (BF) composites that were modified with polyethylene-graft-maleic anhydride (PE-g-MA) and glycerol. Scanning electron microscopy (SEM) and tensile tests of the composites demonstrated poor adhesion between the filler and matrix. Contact angle measurement showed that the surface of LDPE was modified by the presence of the load. The thermal stability of the composites was studied by measuring the oxidation induction time (OIT). Preliminary bacterial penetration tests were performed using culture inoculums of E. coli and S. aureus to investigate the natural antibacterial and bacteriostatic properties attributed to bamboo. Furthermore, bamboo may have interesting antioxidant activity with potential for use in food packaging applications.

A porous biodegradable polyurethane nanocomposite based on poly(caprolactone) (PCL) and nanocomponents derived from montmorillonite (Cloisite®30B) was synthesized and tested to produce information regarding its potential use as a scaffold for tissue engineering. Structural and morphological characteristics of this nanocomposite were studied by infrared spectroscopy (FTIR), X-ray diffraction (XRD), small angle X-ray scattering (SAXS) and scanning electron microscopy (SEM). The reaction between polyurethane oligomers with isocyanate endcapped chains and water led to the evolution of CO2, which was responsible for building interconnected pores with sizes ranging from 184 to 387 μm. An in vitro cell-nanocomposite interaction study was carried out using neonatal rat calvarial osteoblasts. The ability of cells to proliferate and produce an extracellular matrix in contact with the synthesized material was assessed by an MTT assay, a collagen synthesis analysis, and the expression of alkaline phosphatase. In vivo experiments were performed by subcutaneously implanting samples in the dorsum of rats. The implants were removed after 14, 21, and 29 days, and were analyzed by SEM and optical microscopy after tissue processing. Histology crosssections and SEM analyses showed that the cells were able to penetrate into the material and to attach to many location throughout the pore structure. In vitro and in vivo tests demonstrated the feasibility for polyurethane nanocomposites to be used as artificial extracellular matrices onto which cells can attach, grow, and form new tissues.

Polyurethanes have been used in a series of applications due basically to their versatility in terms of controlling the behavior by altering basically the type of reagents used. However, for more specific and advanced applications, such as in membranes, biomaterials and sensors, well-organized and defined chemical functionalities are necessary. In this work, inorganic functionalities were incorporated into aliphatic polyurethanes (PU) having different macromolecular architectures. Polyurethanes were synthesized using a polyether diol and dicyclohexylmethane 4,4' diisocyanate (H12-MDI). Polyurethanes having carboxylic acid groups were also produced by introducing 2,2- bis (hydroxymethyl) propionic acid in the polymerization process. Inorganic functionalities were inserted into polyurethanes by reacting isocyanate end capped chains with aminopropyltriethoxysilane followed by tetraethoxysilane. PU having carboxylic acid groups yielded transparent samples after the incorporation of inorganic entities, as an evidence of smaller and better dispersed inorganic entities in the polymer network. FTIR and swelling measurements showed that polyurethanes having carboxylic acid groups had inorganic domains less packed, condensed and cross-linked when compared to polyurethanes with no carboxylic acid groups. Results also suggested that the progressive incorporation of inorganic moieties in both types of polyurethanes occurred in regions previously activated with inorganic functionalities, instead of by the creation of new domains. The temperatures of thermal decomposition and glass transition were also shifted to higher temperatures when inorganic functionalities were incorporated into polyurethanes.

Tissue engineering has evolved from the use of biomaterials for bone substitution that fulfill the clinical demands of biocompatibility, biodegradability, non-immunogeneity, structural strength and porosity. Porous scaffolds have been developed in many forms and materials, but few reached the need of adequate physical, biological and mechanical properties. In the present paper we report the preparation of hybrid porous polyvinyl alcohol (PVA)/bioactive glass through the sol-gel route, using partially and fully hydrolyzed polyvinyl alcohol, and perform structural characterization. Hybrids containing PVA and bioactive glass with composition 58SiO2-33CaO-9P2O5 were synthesized by foaming a mixture of polymer solution and bioactive glass sol-gel precursor solution. Sol-gel solution was prepared from mixing tetraethoxysilane (TEOS), triethylphosphate (TEP), and calcium chloride as chemical precursors. The hybrid composites obtained after aging and drying at low temperature were chemically and morphologically characterized through infrared spectroscopy and scanning electron microscopy. The degree of hydrolysis of PVA, concentration of PVA solution and different PVA-bioglass composition ratios affect the synthesis procedure. Synthesis parameters must be very well combined in order to allow foaming and gelation. The hybrid scaffolds obtained exhibited macroporous structure with pore size varying from 50 to 600 µm.

Many chemical and physical methods, such as plasma, e-beam, sputtering, CVD and others, have been used to modify the structure of polymer surfaces by depositing thin inorganic films. Most of these techniques are based upon the use of high energy sources that ultimately can damage either chemically or physically polymer surfaces. Moreover, these methods are usually not versatile enough to allow the design of structurally and chemically tailored surfaces through the control of the distribution of chemical functionalities throughout the surface. In this work, inorganic species were introduced onto polymer substrates in a controlled manner by performing a sequence of chemical reactions at the surface. Sulfonation followed by silanization reactions were used to graft alkoxysilane species at the surface of poly(aryl sulfones). The heterogeneous chemical modification of poly(aryl sulfones) was monitored by FTIR-ATR (Attenuated Total Reflection - FTIR). Model compounds were used to study the chemical reactions occurring during the grafting procedure. The results showed that the developed procedure can allow a controlled introduction of inorganic species onto polymer surfaces. Furthermore, in order to prove that this procedure enables the deposition of specific chemical functionalities onto polymer surfaces that can be used to create chemically and structurally tailored surfaces, silicate films were deposited on previously silanated PAS bioactive glass composites. In vitro tests showed that the surface modified composite can enhance the rates of hydroxy-carbonate-apatite precipitation.

Interactions between polymers and inorganic surfaces are present in a series of phenomena involving processes such as coagulation and deffloculation of ceramic powder and adsorption of organic macromolecules on the surface of implants, among others. In this work, Atomic Force Microscopy (AFM) was modified to allow the evaluation of interactions between polymeric chains and inorganic surfaces (silica) with different structures. Polymers (sulfonated polysulfone) were grafted onto AFM cantilevers. AFM force-distance curves were obtained for this modified tip against a series of substrates produced by depositing silica films on silicon wafers. The structure of the silica layer was modified by employing heat treatments at different temperatures. The results showed that the interactions between polymer and surfaces are dependent on the structure of the surfaces. Penetration of the polymeric chains can occur through a soft gel layer (substrates treated at low temperature, 110 °C). For surfaces with dense silica layers, the results showed that not only the concentration of hydroxy groups but also their spatial distribution along the surfaces are important in defining the magnitude of interactions between polymers and surfaces. A model involving a molecular recognition process, in which interactions are maximized for inorganic surfaces with structures that can match the chemical architecture of the polymer, was then used to explain the obtained results.