Search

Laser beam remelting is a relatively simple and highly effective technique for the physical modification of surfaces to improve resistance to cavitation erosion. In this study, we investigated the effect of laser remelting on the surface of cast stainless steel with 0.40% C, 25% Cr, 20% Ni, and 1.5% Si on cavitation erosion behavior in tap water. The investigation was conducted using a piezoceramic crystal vibrator apparatus. Base laser beam parameters were carefully selected to result in a defect-free surface (no porosity, material burn, cracks) with hardness capable of generating better resistance to cavitation erosion. The experimental results were compared with those of the reference material. Surface morphology and microstructure evolution after cavitation tests were analyzed using an optical metallographic microscope (OM), scanning electron microscope (SEM), and hardness tests to explore the mechanism of improving surface degradation resistance. The conducted research demonstrated that surfaces modified by laser remelting exhibit a 4.8–5.1 times greater increase in cavitation erosion resistance due to the homogenization of chemical composition and refinement of the microstructure, while maintaining the properties of the base material. [ABSTRACT FROM AUTHOR]

In this paper, issues related to the technology of compound castings composed of two parts, i.e., the working layer and the supporting part, made of X46Cr13 high-chromium steel and EN-GJL-HB 255 grey cast iron, respectively, in a liquid–solid system by pre-installing a monolithic insert in the mould cavity are presented. As a part of the research, the mechanism of formation of transitional zones in the bonding area of the above-mentioned two alloys was identified and described. It was shown that the phenomenon that determines the formation of a permanent bond between the joined materials is the transport of C and heat from the "high-carbon and hot" material of the supporting part poured into the mould in the form of liquid cast iron to the "low-carbon and cold" material of the working layer placed in the form of a steel monolithic insert inside the mould cavity. In the paper, the suitability of the compound castings technology developed for use in the coke industry is also presented. Full-size high-chromium steel–grey cast iron compound casting plates designed for the coke quenching car lining were positively verified in real coke plant operating conditions. [ABSTRACT FROM AUTHOR]

Duplex steel and cast steels have a wide range of applications in many industrial sectors, for example, oil extraction, printing, petrochemical industry, energy—exhaust gases desulphurization systems, seawater desalination plants, and the shipbuilding industry. The machine elements can be produced with different techniques, which determine the operational properties. A material with the same chemical composition made as a casting will have worse mechanical properties than, for example, a forged element. This depends on the microstructure, its fragmentation and its morphology. However, the costs of casting are lower than, for example, forging, and, in addition, not all shapes obtainable in the casting process can be made using metal–plastic working methods. This article presents research results concerning the influence of the burnishing process on the properties of the duplex cast steel surface layer. The purpose of the research was to verify the impact of static pressure roller burnishing (SPRB) parameters on the wear of the surface layer of duplex cast steel. The subject of the research was cast steel in the GX2CrNiMoN22-5-3 grade—according to PN-EN 10283:2019—that was burnished using 15 variants of technological parameters. Then, the samples were subjected to surface wear tests using the INSTRON 8874 device. On the basis of the observed wear appearances, the acting wear mechanisms are defined and evaluated according their contribution to the wear behavior. Detailed information about the wear phenomena will help industries to minimize their maintenance losses related to surface wear. The possibility of shaping surface properties by mechanical burnishing is part of the current direction of surface engineering development. This technology, combined with a high-potential material such as duplex cast steel, makes it possible to increase wear resistance. [ABSTRACT FROM AUTHOR]

In advancing special materials, seamless integration into existing production chains is paramount. Beyond creating improved alloy compositions, precision in processing methods is crucial to preserve desired properties without drawbacks. The synergy between alloy formulation and processing techniques is pivotal for maximizing the benefits of innovative materials. By focusing on advanced deep processing technology for small ingots of modified 12% Cr stainless steel, this paper delves into the transformation of cast ingot steel structures using radial shear rolling (RSR) processing. Through a series of nine passes, rolling ingots from a 32 mm to a 13 mm diameter with a total elongation factor of 6.02, a notable shift occurred. This single-operation process effectuated a substantial change in sample structure, transitioning from a coarse-grained cast structure (0.5–1.5 mm) to an equiaxed fine-grained structure with peripheral grain sizes of 1–4 μm and an elongated rolling texture in the axial part of the bar. The complete transformation of the initial cast dendritic structure validates the implementation of the RSR method for the deep processing of ingots. [ABSTRACT FROM AUTHOR]

This paper presents the results of studies on the occurrence of transient disturbances in the hydrodynamic system of a tundish feeding area and their effect on the casting process. In addition, the effect of changes in the level of superheating of the molten steel fed to the tundish on the evolution of the hydrodynamic system was analyzed. The studies were conducted with the use of a physical model of the tundish and a numerical model, representing the industrial conditions of the process of the continuous casting of steel. When a tundish is fed through a modified ladle shroud that slows down the momentum of the stream, this creates favorable conditions for the emergence of asymmetrical flow within the working tundish volume. The higher the degree of molten steel reheating in the ladle furnace, the stronger the evolution of the hydrodynamic structures in the tundish during the casting process. [ABSTRACT FROM AUTHOR]

The continuous steel casting process must simultaneously meet the requirements for production performance, quality and safety against breakouts. Knowing the thickness of the solidified shell, particularly at the exit of the mould, is useful for the casting process control and breakout prevention. Shell thickness is difficult to measure during casting; in practice, it is predicted by indirect methods and models. But after undesired rupture of the shell and leakage of the liquid steel, it is possible to measure the shell thickness directly. This article is focused on the problem of the growth and measurement of the solid shell obtained after the breakout of a round block with a diameter of 410 mm. An original methodology was developed in which a surface mesh of points was created from the individual scanned parts of the block using a 3D laser scanner. Research has shown differences of up to 6 mm between the maximum and minimum shell thickness at the mould exit. A regression function of the average shell thickness on time was found. The results of the real shell growth were further used for the verification of the original numerical model of cooling and solidification of the round block. [ABSTRACT FROM AUTHOR]

The endurance limit of structural mechanical components is affected by the residual stress state, which depends strongly on the manufacturing process. In general, compressive residual stresses tend to result in an increased fatigue strength. Post-manufacturing processes such as shot peening or vibratory finishing may achieve such a compressive residual stress state. But within complex components, manufacturing-process-based imperfections severely limit the fatigue strength. Thus, the interactions of imperfections, residual stress state and material strength are key aspects in fatigue design. In this work, cast steel and aluminium alloys are investigated, each of them in vibratory finished and polished surface condition. A layer-based fatigue assessment concept is extended towards stable effective mean stress state considering the elastic–plastic material behaviour. Murakami's concept was applied to incorporate the effect of hardness change and residual stress state. Residual stress relaxation is determined by elastic–plastic simulations invoking a combined hardening model. If the effective stress ratio within the local layer-based fatigue strength is evaluated as critical distance value, a sound calculation of fatigue strength can be achieved. Summing up, the layer-based fatigue strength design is extended and features an enhanced understanding of the effective stabilized mean stress state during cyclic loading. [ABSTRACT FROM AUTHOR]

Super austenitic stainless steels are expected to replace expensive alloys in harsh environments due to their superior corrosion resistance and mechanical properties. However, the ultra-high alloy contents drive serious segregation in cast steels, where the σ phase is difficult to eliminate. In this study, the microstructural evolution of 7Mo super austenitic stainless steels under different homogenization methods was investigated. The results showed that after isothermal treatment for 30 h at 1250 °C, the σ phase in steels dissolved, while the remelting morphologies appeared at the phase boundaries. Therefore, the stepped solution heat treatment was further conducted to optimize the homogenized microstructure. The samples were heated up to 1220 °C, 1235 °C and 1250 °C with a slow heating rate, and held at these temperatures for 2 h, respectively. The elemental segregation was greatly reduced without incipient remelting and the σ phase was eventually reduced to less than 0.6%. A prolonged incubation below the dissolution temperature will lead to a spontaneous compositional adjustment of the eutectic σ phase, resulting in uphill diffusion of Cr and Mn, and reducing the homogenization efficiency of ISHT, which is avoided by SSHT. The hardness reduced from 228~236 Hv to 220~232 Hv by adopting the cooling process of "furnace cooling + water quench". In addition, the study noticed that increasing the Ce content or decreasing the Mn content can both refine the homogenized grain size and accelerate diffusion processes. This study provides a theoretical and experimental basis for the process and composition optimization of super austenitic stainless steels. [ABSTRACT FROM AUTHOR]

This paper focuses on relationship between the mechanical properties and abrasive wear resistance, expressed by the Kb index, using an example of low-alloy cast steels. In order to achieve the aim of this work, eight cast steels of varying chemical composition were designed, cast and then heat treated. The heat treatment involved quenching and tempering at 200, 400 and 600 °C. Structural changes caused by tempering are demonstrated by the different morphologies of the carbide phases in the ferritic matrix. In the first part of this paper, the present state of knowledge about the influence of structure and hardness on the tribological properties of steels is discussed. This research involved the evaluation of a material's structure, as well as its tribological and mechanical properties. Microstructural observations were performed using a light microscope and a scanning electron microscope. Next, tribological tests were carried-out with the use of a dry sand/rubber wheel tester. To determine the mechanical properties, Brinell hardness measurements and a static tensile test were carried out. The relationship between the determined mechanical properties and abrasive wear resistance was then investigated. The analyses also provided information regarding the heat treatment states of the analyzed material in the as-cast and as-quenched states. It was found that the abrasive wear resistance, expressed by the index Kb, was most strongly correlated with hardness and yield point. In addition, observations of the wear surfaces indicated that the main wear mechanisms were microcutting and microplowing. [ABSTRACT FROM AUTHOR]

In this study, a newly developed high-strength cast Fe81Cr15V3C1 (wt%) steel with a high resistance against dry abrasion and chloride-induced pitting corrosion is presented. The alloy was synthesized through a special casting process that yielded high solidification rates. The resulting fine, multiphase microstructure is composed of martensite, retained austenite and a network of complex carbides. This led to a very high compressive strength (>3800 MPa) and tensile strength (>1200 MPa) in the as-cast state. Furthermore, a significantly higher abrasive wear resistance in comparison to the conventional X90CrMoV18 tool steel was determined for the novel alloy under very harsh wear conditions (SiC, α-Al2O3). Regarding the tooling application, corrosion tests were conducted in a 3.5 wt.% NaCl solution. Potentiodynamic polarization curves demonstrated a similar behavior during the long-term testing of Fe81Cr15V3C1 and the X90CrMoV18 reference tool steel, though both steels revealed a different nature of corrosion degradation. The novel steel is less susceptible to local degradation, especially pitting, due to the formation of several phases that led to the development of a less dangerous form of destruction: galvanic corrosion. In conclusion, this novel cast steel offers a cost- and resource-efficient alternative to conventionally wrought cold-work steels, which are usually required for high-performance tools under highly abrasive as well as corrosive conditions. [ABSTRACT FROM AUTHOR]

Cast austenitic chromium-nickel steel is commonly used for the manufacture of machine parts and components, which are exposed to the attack of corrosive media and abrasive wear during operation. The most commonly used grades include GX2CrNi18-9 and X10CrNi18-8 as well as GX2CrNiMo17-12-2 and X6CrNiMoNb17-12-2. To improve the abrasion resistance of cast chromium-nickel steel, primary niobium carbides were produced in the metallurgical process by increasing the carbon content and adding Fe-Nb. The microstructure of the obtained test castings consisted of an austenitic matrix and primary niobium carbides evenly distributed in this matrix. The measured hardness of the samples after heat treatment ranged from 215 to 240 HV and was higher by about 60 units than the hardness of the reference cast GX10CrNi18-9 steel, which had a hardness of about 180 HV. Compared to the reference cast steel, the abrasive wear resistance of the tested cast chromium-nickel steel (measured in Miller test) with contents of 4.4 and 5.4 wt% Nb increased only slightly, i.e., by 5% for the lower niobium content and 11% for the higher niobium content. Compared to ordinary cast GX10CrNi18-9 steel, the addition of 9.2 wt% Nb reduced the abrasive wear by almost 2.5 times. [ABSTRACT FROM AUTHOR]

Cavitation erosion degrades the surface of engineering components when the material is exposed to turbulent fluid flows. Under conditions of local pressure fluctuations, a nucleation of gas or vapor bubbles occurs. If the pressure suddenly drops below the vapor pressure, these bubbles collapse violently when subjected to higher pressure. This collapse is accompanied by the sudden flow of the liquid, which is manifested by stress pulses capable of causing plastic deformations on solid surfaces. Repeating these stress conditions can cause material removal and ultimately failure of the component itself. The present study aims to reduce the negative impact of this phenomenon on the mechanical systems components, using the TIG local surface remelting technique. Cavitation erosion tests were performed in accordance with the ASTM G32-2016 standard on samples taken from a cast high-alloy stainless steel. The alloy response for each melting current value was investigated by measuring mass loss as a function of cavitation attack time and by analyzing the damaged surfaces using optical and scanning electron microscopes. It was highlighted that the TIG remelted layers provide an increase in cavitation erosion resistance of 5–6 times as a consequence of the fine graining and microstructure induced by the technique applied. [ABSTRACT FROM AUTHOR]

With the increasing demand for special steel, the quality of steel has become critical during the continuous casting tundish process. In recent years, tundish heating technology has played a key role in low superheat casting. Toward this, researchers have reported on the metallurgical effects of induction heating tundish (IHT). From 1984 to date, the channel-type IHT has been investigated in the production of continuous casting of special steel. In this article, the principle of this channel-type IHT technology and equipment composition were illustrated. A brief summary and comments were undertaken on the channel-type IHT, including physical modeling and numerical modeling. The application development trend of tundish induction heating equipment is summarized combined with industrial application data, which provide a reference for a better understanding of the induction heating process of tundish. [ABSTRACT FROM AUTHOR]

Unreinforced masonry (URM) is one of the most popular construction materials around the world, but vulnerable during earthquakes. Due to its brittle nature, the URM structures may lead to a possible collapse of the wall of a building during earthquake events causing casualties. In the current research, an attempt is made to enhance the seismic capacity of URM structures by proposing a new innovative composite material that can improve the shear strength and deformation capacity of the URM wall systems. The results revealed that the fiber-reinforced plastic having high tensile and shear stiffness can significantly increase in-plane as well as out-of-plane bending strength of the URM wall. It was recorded that the bending moment of the prism increased up to 549.5% by increasing the bending moment from 490 N*mm to 3183 N*mm per mm deflection of prism upon using glass fibers. Moreover, the ductility ratio amplified up to 5.73 times while the stiffness ratio increased up to 4.16 times with the aid of glass fibers. Since the material used in this research work is low cost, easily available, and no need for any skilled labor, which is economically good. Therefore, the URM walls retrofitted with fiber-reinforced plastic is an economical solution. [ABSTRACT FROM AUTHOR]

The article presents the results of research on the properties of molding sands in Alphaset technology (alkaline-phenolic). These sands are often used in steel foundries, producing large castings. However, knowledge about them, and especially about the changeability of their properties with the change of environmental conditions (seasons), is still insufficient. Various compositions of molding sand were analyzed based on fresh chromite sand and reclaimed sand. A binder and hardener in various mass ratios were used to prepare the mass. The research methodology included, among others, tests of tensile and bending strength, permeability, abrasion, gas emissivity, and ignition losses. These tests were carried out for summer and winter conditions. The results showed the optimal proportions of resin and hardener, showed the influence of ambient temperature on the properties of the molding sand, and the possible ratio of reclaimed sand in relation to fresh sand. However, you should always remember to verify them under the conditions of a specific foundry. [ABSTRACT FROM AUTHOR]

Changes in the microstructure and selected mechanical properties of two-phase ferritic-austenitic cast steel containing 24% Cr-5% Ni-2.5% Mo-2.5% Cu after isothermal holding at 750 °C and 900 °C are presented. The choice of the two temperatures of isothermal holding was dictated by the precipitation of brittle phases within a range of 600 °C–950 °C, while the holding time depended on the casting cooling time in the mould. Changes in the microstructure were studied by the SEM-EDS and XRD techniques. As a result of the decomposition of the eutectoid ferrite, a σ phase that was rich in Cr, Mo, and Ni and a secondary γ2 austenite with Widmannstätten morphology were formed. Compared to the austenite, the chemical composition of the secondary γ2 austenite showed depletion of Cr and Mo. In the ferrite, the presence of Cr2N nitrides was also detected. After a holding time of 3 h at 900 °C, these phases increased the hardness of the tested cast steel to approximately 275 HV10. At the same time, the UTS value was recorded to decrease with the increasing temperature based on the tensile test results. At 750 °C, the value of UTS was 250 MPa for 1 h of holding and 345 MPa for 3 h of holding. These values decreased after increasing the temperature to 900 °C and amounted to 139 for 1 h holding and 127 MPa for 3 h holding. It was also found that the elongation values at 750 °C ranged from 7–10%, while they amounted to 35–37% at 900 °C. A fracture analysis of the tested cast steel showed that in the prevailing part, the fractures were made of ductile nature with an arrangement of dimples that is typical for this type of fracture. Non-metallic inclusions that are typical for cast steel (i.e., oxides and nitrides) were also found in the area of the fractures. [ABSTRACT FROM AUTHOR]

Tests were carried out on two high-Mn steels: 27Mn-4Si-2Al-Nb with Nb microaddition and 24Mn-3Si-1.5Al-Nb-Ti with Nb and Ti microadditions. High-manganese austenitic steels, due to their good strength and plastic properties belong to the AHSS (Advanced High-Strength Steel) group and are used in the automotive industry. The main difficulties faced during the casting of the steel and hot working are hot cracks, which can appear in the surface of the ingot. Cracks on the edges of the sheet after hot rolling are the reason for cutting the edges of the sheet and increasing production costs and material losses. The main reason for the formation of hot cracks is the decrease in metal ductility in the high-temperature brittleness range (HTBR). The width of the HTBR depends on mechanical properties and microstructural factors, i.e., non-metallic inclusions or intermetallic phases at austenite grain boundaries. In this paper, a hot tensile test was performed. The research was performed on the GLEEBLE 3800 thermomechanical simulator. This test allows us to determine the width of the high-temperature brittleness range (HTBR), the Nil Strength Temperature (NST), the Nil Ductility Temperature (NDT), and the Ductility Recovery Temperature (DRT). Hot ductility was determined from the value of the reduction in area R(A). The obtained results make it possible to determine the temperature of the beginning of hot working from the tested high-Mn steels. Fractographic research enabled us to define mechanisms of hot cracking. It was found that hot cracks form as a result of disruptions in the liquid film on crystals' boundaries. [ABSTRACT FROM AUTHOR]

Cast steel is commonly used to produce structural and safety parts. Foundry processes allow producing parts from scrap steel directly to the required dimensions without any forming operation. Cast components may, however, exhibit macro- and micro-shrinkage porosities. The combined effect of macro- and micro-shrinkages on the fatigue behavior of cast steel has been characterized in the literature. Macro-shrinkages may nowadays be eliminated by adequate positioning of risers. However, micro-shrinkages will always be present in cast steel components. Present work addresses the influence of micro-shrinkage porosity on a G20Mn5 cast steel. G20Mn5 (normalized) ingots have been cast under industrial conditions, but ensuring the absence of macro-porosities. Solidification leads to two very different microstructures prior to the normalization treatment: columnar dendrites beneath the surface (Skin) and equiaxed microstructures close to the center (Core). First, metallographic observations of the whole ingot revealed the same grain size in both areas. Fatigue samples were extracted, by differentiating two sampling volumes corresponding to columnar (S) and equiaxed solidification (C), respectively. The distribution of micro-porosities was determined on all samples by Micro-CT-scans. Core samples exhibit micro-porosities with volumes 1.7 larger than Skin samples. Low cycle fatigue tests (3 levels of fixed plastic strain) were run on both sample series (C, S). Results follow a Manson–Coffin law. Core specimens exhibit lower fatigue life than Skin specimens. The differences in fatigue life have been related successfully to the differences in micro-porosities sizes. [ABSTRACT FROM AUTHOR]

This study seeks to investigate the local reinforcement of low carbon cast steel specimens with WC–metal matrix composites (WC–MMCs), to obtain a new material effective in competing with hard alloy steels. For this purpose, a powder compact of tungsten carbide (WC) and iron (Fe) was prepared and placed in the mold cavity before casting. The reactions that occurred with the molten steel led to the formation of the WC–MMC and, consequently, to the local reinforcement of the steel. The microstructure of the WC–MMC reinforcement was characterized by scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and electron backscatter diffraction (EBSD). The results showed a microstructural variation throughout the depth of the reinforcement. In the surface region, most of the original WC particles retain their polygonal morphology, but towards the base metal, the dissolution of the WC particles increased with the formation of (Fe,W)6C carbides. Closer to the base metal, dendritic eutectic carbides of (Fe,W)6C and fine (Fe,W)23C6 precipitates in a matrix of martensite were formed. The mechanical properties of the reinforcement were evaluated by hardness and ball-cratering abrasion tests. The results revealed a significant increase in hardness, being three times harder than the base metal, and a decrease of 39% in the wear rate. [ABSTRACT FROM AUTHOR]

The aim of the study was to determine the effect of zone reinforcement of cast steel L120G13 with Al2O3 macro-particles on the corrosion resistance of the composite obtained in this way. The obtained results allow us to conclude that strengthening of cast steel with corundum, the aim of which was to significantly increase the abrasive wear resistance, did not significantly deteriorate corrosion resistance. SEM tests show that a permanent diffusion layer interface is formed at the boundary between cast steel and corundum. In this area, simple manganese segregation and reverse iron and chromium segregation were found. These elements pass from the liquid alloy to the surface layer of the corundum particles, causing the aluminium and oxygen to be pushed deep into the corundum grains. Corrosion tests indicate comparable corrosion resistance of cast steel L120G13 and the composite L120G13 + Al2O3. Moreover, no intergranular corrosion was found in the matrix of the composite and no signs of pitting corrosion were found in the areas of the interface between the phases of the composite. This information is extremely important from the point of view of the material's service life. Observations of breakthrough of both materials obtained during fracture after potentiodynamic corrosion tests, immediately after freezing in liquid nitrogen, indicate cracking with plastic features and increased resistance to dynamic forces of cast steel L120G13 and the composite L120G13 + Al2O3. [ABSTRACT FROM AUTHOR]

When various alloying elements are added or the cooling rate is increased, steel grades with U- or V-typed ductility behavior show N-shaped ductility behavior in which the ductility decreases in the low-temperature region. This study proposes a method that uses N-shaped data fitting and random forest to predict ductility behavior of steel grades that have bainite microstructure. To include the phenomenon in which that ductility decreases below the intermediate temperature, the data range was extended to temperature T < 700 °C. To identify the T range in which the ductility decreases at T < 700 °C, an N-shaped data fitting method using six parameters was proposed. Comparison with the experimental values confirmed the effectiveness of the proposed model. Also, the model has better ability than models to predict bainite start temperature TBS. In a case study, the change of ductility behavior according to the cooling rate was observed for Nb-added steel. As the cooling rate increased from 1 °C/s to 10 °C/s, the formation of hard phase was relatively promoted, and different transformation behaviors appeared. This ability to predict the ductility behavior of alloy steels with a bainite microstructure, and to predict TBS below the intermediate temperature enables effective control of the secondary cooling conditions during continuous casting process, minimizing the formation of cracks on the slab surface. [ABSTRACT FROM AUTHOR]

The mineralogical structure of flux films is a critical factor in controlling heat transfer in the mold and avoiding the longitudinal cracking of slabs during the continuous casting of peritectic steel. In this study, the layered structure, crystallization ratio, mineralogical species, and morphology features of flux films were characterized by optical microscopy, X-ray diffraction, and electron-probe microanalysis. Microstructural observation revealed that the normal flux films for peritectic steels present a multilayered structure and high crystallization ratio (60~90 vol%), mainly composed of well-developed crystalline akermanite and cuspidine. In contrast, the films with outstanding flux characteristics with abundant longitudinal cracks on the slab surface have a low crystallization ratio (<50 vol%) or vast crystallite content (>80 vol%). Furthermore, heat transfer analysis showed that the low crystallization ratio and the vast crystallite content of flux films worsen the heat transfer rate or uniformity in the mold, whereas the appropriate thickness and cuspidine content of flux films can improve the heat transfer performance. From the above results, it is concluded that using strong crystalline flux to obtain the ideal mineral phase structure of flux film is one of the important measures for reducing longitudinal cracks during continuous casting of peritectic steel slabs. [ABSTRACT FROM AUTHOR]

Hadfield steel, under unit pressure conditions, strengthens itself by forming a high density dislocation structure, which results in increased resistance to dynamic impact wear. However, under abrasion conditions, the homogeneous microstructure of the cast steel is insufficient to achieve the expected service life. The aim of the research is to conduct a comparative analysis of the material in its as-delivered state and after two-stage heat treatment (isothermal annealing followed by re-austenitisation). It was found that after isothermal annealing of X120Mn12 grade steel at a temperature of 510 °C, a microstructure with a complex morphology consisting of colonies of fine-grained pearlite, (Fe,Mn)3C carbides distributed along the grain boundaries of the former austenite and needle-like (Fe,Mn)3C carbides was obtained in the austenite matrix. The subsequent thermal treatment of the steel with the use of supersaturating annealing at 900 °C resulted in a heterogeneous microstructure consisting of evenly distributed globular carbide precipitations in a matrix of considerably finer austenite grains in comparison with the as-delivered original state. As a result of the final microstructural changes achieved, a 16.4% increase in abrasion resistance was obtained compared to the delivered condition. [ABSTRACT FROM AUTHOR]

The high temperature brittleness range of medium carbon microalloyed steel under an actual continuous casting process was determined by the high temperature tensile test. The test results revealed that only a third of the brittle temperature range from 650–825 °C was due to intergranular ferrite in the experimental steel. In addition, it was found that the plastic recovery was fast and stable when the temperature was lower than 725 °C (the lowest plastic temperature). Bending/straightening operation in this temperature range was conducive to controlling the generation of corner cracks. In order to keep the corner temperature at the low temperature end of the plastic curve when the slab was bent/straightened, the cooling water scheme of the secondary cooling zone of the continuous caster was formulated by numerical calculation. By appropriately increasing the cooling water flow in the foot roll and the secondary cooling zones 1–5, the corner temperature of slab during bending operation was 600–700 °C, avoiding the brittle temperature range. The industrial test was then carried out. The results showed that after using the optimized water volume, the corner grains of the slab were uniform and the microstructure was mainly pearlite + ferrite. In addition, the abnormally large grain size was reduced, and a large amount of ferrite was generated inside the grain, which avoided stress concentration at the corner of the slab during bending/straightening operation, and basically eliminated the corner crack of the slab. [ABSTRACT FROM AUTHOR]

In the original publication [[1]], there were mistakes in Figure 11b as published including Y scale, value of melt 6 under 200 °C and relationship between melt 1 and melt 2 under all temperature conditions. The corrected Figure 11b appears below. The authors state that the scientific conclusions are unaffected. This correction was approved by the Academic Editor. The original publication has also been updated.FigureGraph: Figure 11 Hardness (a) and yield point (b) of the analyzed alloys after quenching and tempering at 200, 400 and 600 °C.By Beata Białobrzeska and Robert JasińskiReported by Author; Author [Extracted from the article]

Tensile properties on ASTM A216 WCB cast steel with centerline porosity defect were studied with radiographic mapping and finite element remodeling technique. Non-linear elastic and plastic behaviors dependent on porosity were mathematically described by relevant equation sets. According to the ASTM E8 tensile test standard, matrix and defect specimens were machined into two categories by two types of height. After applying radiographic inspection, defect morphologies were mapped to the mid-sections of the finite element models and the porosity fraction fields had been generated with interpolation method. ABAQUS input parameters were confirmed by trial simulations to the matrix specimen and comparison with experimental outcomes. Fine agreements of the result curves between simulations and experiments could be observed, and predicted positions of the tensile fracture were found to be in accordance with the tests. Chord modulus was used to obtain the equivalent elastic stiffness because of the non-linear features. The results showed that elongation was the most influenced term to the defect cast steel, compared with elastic stiffness and yield stress. Additional visual explanations on the tensile fracture caused by void propagation were also given by the result contours at different mechanical stages, including distributions ofMises stress and plastic strain. [ABSTRACT FROM AUTHOR]

The aim of this study was to obtain a predictive model able to perform an early detection of central segregation severity in continuous cast steel slabs. Segregation in steel cast products is an internal defect that can be very harmful when slabs are rolled in heavy plate mills. In this research work, the central segregation was studied with success using the data mining methodology based on multivariate adaptive regression splines (MARS) technique. For this purpose, the most important physical-chemical parameters are considered. The results of the present study are two-fold. In the first place, the significance of each physical-chemical variable on the segregation is presented through the model. Second, a model for forecasting segregation is obtained. Regression with optimal hyperparameters was performed and coefficients of determination equal to 0.93 for continuity factor estimation and 0.95 for average width were obtained when the MARS technique was applied to the experimental dataset, respectively. The agreement between experimental data and the model confirmed the good performance of the latter. [ABSTRACT FROM AUTHOR]

Hadfield cast steel is characterized by high wear resistance, but this is only when it is subjected to the effect of dynamic loads. During unloaded abrasion, e.g., sand abrasion, its wear resistance is very low and comparable to the wear of carbon cast steel. To increase the wear resistance of this alloy for operation under the conditions of low pressure or low stress, primary vanadium carbides were produced by the metallurgical process to obtain a two-phase structure after alloy solidification. Compared to samples made of Hadfield cast steel, the primary, very hard carbides, evenly distributed in an austenitic or austenitic-martensitic matrix, increase (at least three times) the wear resistance of samples tested in an abrasive mixture of silicon carbide and water. The changes in microstructure and hardness obtained in alloys after heat treatment (quenching at 1000–1150 °C in water and tempering at 600 °C) are presented. The bulk hardness of the matrix ranged from 370 HV to 660 HV. After heat treatment, the secondary, dispersed vanadium carbides, precipitated in the alloy matrix. [ABSTRACT FROM AUTHOR]

The main task for a ballast bed is to transmit the sleeper pressure in a form of stress cone to the subsoil, provide proper drainage and resist the sleeper displacement. Poorly maintained ballast could severely limit the maximum speed capacity and create further problems with the structural integrity, possibly leading to a complete failure of a given rail line. To prevent the unwanted corollaries, the ballast bed has to be periodically cleaned with an appropriate machinery. In this paper the authors investigated the effect of the chemical composition on the physical properties of the ballast excavating chains made of high-manganese steels. The authors focused on the wear mechanism, work hardening ability and hardness in the cross-sections areas. A microstructure analysis was performed as well, and observations revealed divergent morphology of precipitations at the grain boundaries, which influenced the size of austenite grains. The deformation twins formed as a result of operation were noticed in the samples. Research has shown that less carbon and chromium reduces the hardness of cast steel, and it specifically affects the ability to strain hardening. The authors explained the role of adjustments in chemical composition in the operational properties of high-manganese cast steels. It has been shown in the paper that different chemical compositions affect the properties of the alloys, and this causes different types of wear. The high content of chromium increases the hardness of materials before and after plastic deformation hardening, which in the conditions of selector chains results in greater dimensional stability during wear of holes in pin joints and will be more susceptible to abrasive wear in the presence of dusts from the ballast than creep. [ABSTRACT FROM AUTHOR]

An unjustified simplification of the local quantitative criterion regarding cleavage nucleation is a key problem in the utilisation of the Local Approach to Fracture (LA), particularly to predict the fracture toughness within the ductile-to-brittle transition (DBT) region. The theoretical concept of the effect of both temperature and the plastic strain value on the crack nuclei (CN) generation rate in iron and ferritic steels is presented. It is shown how the plastic strain and temperature affect CN formation rate and, as a consequence, govern the shape of the temperature dependence of fracture toughness KJc and its scatter limits. Within the framework of the microscopic model proposed, dependences of the CN bulk density on the plastic deformation value and temperature are predicted. Convenient approximation dependences for incorporating this effect into the LA are suggested. The experimental data of reactor pressure vessel steel and cast manganese steel demonstrate that the use of these dependences enables one to predict, with sufficient accuracy, the effect of temperature on the value of fracture toughness and its scatter limits over the DBT region. It is shown that accounting for both the temperature and strain dependence of CN bulk density gives rise to the invariance of parameters of the Weibull distribution to temperature. [ABSTRACT FROM AUTHOR]

Tungsten carbide (WC) is well known as one of the hardest materials widely used in machining, cutting and drilling, especially for cutting tools production. Knowing fracture toughness grants the opportunity to prevent catastrophic wear of a tool. Moreover, fracture toughness of WC-based materials may vary because of different material compositions, as well as a different way of production. Hence, each material should be treated individually. In this paper, SM25T (HW) tungsten carbide (HW—uncoated grade, TNMR 401060 SM25T, manufactured by Baildonit company, Katowice, Poland) was taken into consideration. Sintered carbides—designated as S—are designed to be applied for machining steel, cast steel and malleable cast iron. Fracture mechanics methods were adapted to make a quality assessment of WC cutting inserts. Both quasi-statical three-point bending tests, as well as Charpy dynamic impact tests, were performed to calculate static and dynamic fracture toughness (KIC and KID, respectively). In addition, a special emphasis was placed on the microscopic analysis of fracture surfaces after impact tests to discuss material irregularities, such as porosity, cracks and so-called "river patterns". There is a lack of scientific works in this field of study. However, cutting engineers are interested in obtaining the experimental results of that kind. Although there are a few standardized methods that may be used to determine fracture toughness of hard metals, none of them is expected to be the most reliable. Moreover, there is a lack of scientific works in the field of determining static and dynamic fracture toughness of WC by the presented method. The proposed examination solution can be then successfully used to calculate toughness properties of WC-based materials, as the results obtained seem to be with a good agreement with other works. [ABSTRACT FROM AUTHOR]

The strengthening mechanism of 9Cr–1.5Mo–1Co and 9Cr–3W–3Co heat resistant steel was studied by tensile test and microstructure analysis. At the same temperature, the yield strength of 9Cr–3W–3Co heat-resistant steel is higher than that of 9Cr–1.5Mo–1Co heat-resistant steel. Microstructure analysis proved that the strength of 9Cr–1.5Mo–1Co and 9Cr–3W–3Co heat-resistant steel is affected by grain boundary, dislocation, precipitation, and solid solution atoms. The excellent high temperature mechanical properties of 9Cr–3W–3Co heat-resistant steel are mainly due to the solution strengthening caused by Co and W atoms and the high-density dislocations distributed in the matrix; however, 9Cr–1.5Mo–1Co heat-resistant steel is mainly due to the martensitic lath and precipitation strengthening. [ABSTRACT FROM AUTHOR]

Ferrous alloys (steels and cast irons) and their heat treatment have attracted a great amount of basic and applied research due to their decisive importance in modern industrial branches such as the automotive, transport and other industries. Heat treatment is always required for these materials, in order to achieve the desired levels of strength, hardness, toughness and ductility. Over the past decades, many advanced heat- and surface-treatment techniques have been developed such as heat treatment in protective atmospheres or in vacuum, sub-zero treatment, laser/electron beam surface hardening and alloying, low-pressure carburizing and nitriding, physical vapour deposition and many others. This diversity of treatment techniques used in industrial applications has spurred a great extent of research efforts focused on the optimized and/or tailored design of processes in order to promote the best possible utilization of material properties. This special journal issue contains a collection of original research articles on not only advanced heat-treatment techniques—carburizing and sub-zero treatments—but also on the microstructure–property relationships in different ferrous alloys. [ABSTRACT FROM AUTHOR]

Additive Manufacturing (AM) technology has unique advantages in producing complex joints in architecturally exposed steel structures. This article focuses on the process of manufacturing and investigating the mechanical properties of a reduced scale model of a trifurcated joint using Selective Laser Melting (SLM) method and mechanical tests, respectively. The orthogonal test method was used to optimize the main AM process parameters. Then the trifurcated steel joint was printed using the optimal process parameters and treated by solid solution and aging treatment. To investigate the mechanical performance of the printed joint, an axial compression test and complimentary finite element analyses were carried out. Failure processes and failure mechanisms of the trifurcated steel joint were discussed in detail. The research results show that the preferred process parameters for printing 316L stainless steel powder are: scanning power 150 W, scanning speed 700 mm/s, and scanning pitch 0.09 mm. Using these AM parameters, trifurcated steel joints with good surface quality, geometrical accuracy and tensile strength are obtained after heat treatment. Our mechanical tests and Finite element analyses results indicate that the failure mechanism in the AM trifurcated joint are similar to those of cast steel joints. Based on these results, we conclude that the AM technology serves as a promising new way for the fabrication of joints with complex geometries. [ABSTRACT FROM AUTHOR]

The paper presents an experimental study on microstructure changes in duplex steel after hot deformation. Duplex steels and cast steels are characterized by a multiphase microstructure. They are relatively new materials with great contributions to the many fields of industries. Due to the fact of deforming two different phase austenite and ferrite those materials have a complex plasticity. This work is a continuation and complementation of previous works and is a significant supplement to information presented in them. The article concerns precipitation phenomena and changes in the microstructure of two grades of ferritic-austenitic steels: X2CrNiMoN25-7-4 and X2CrNiMoCuN25-6-3. Those steels have a very similar chemical composition, differing by only 2.5% copper content. An important aspect presented in the work is we observed that adding 2.5% copper prevented precipitation of the destructive sigma phase during the hot deformation. [ABSTRACT FROM AUTHOR]

The microstructure evolution, mechanical properties, and tribological properties of high boron cast steel (HBCS) with various Mo concentrations are investigated. The results indicate that Mo addition can significantly modify the microstructure and enhance the comprehensive properties. With the increase of Mo concentration, borides change from the original fish-bone Fe-rich and Cr-rich M2B to dendritic Fe-rich M2B, blocky and cluster-like Cr-rich M2B, and grainy Mo-rich M2B. The hardness of HBCS increases gradually with the increase of Mo content due to the solid solution strengthening and the refinement of M2B. It can be found that all the samples exhibit quasi-cleavage, but the impact toughness increases firstly and reaches the maximum value when the concentration of Mo is 2.10 wt.%, which is the result of the dispersive distribution of M2B rather than the original fish-bone M2B. Subsequently, the impact toughness begins to decrease as the concentration of Mo further increases because of the extensive formation of grainy Mo-rich M2B at the grain boundary. Meanwhile, the wear results reveal that the average friction coefficient and wear ratio decrease with the increase of Mo content, and the wear mechanism changes from abrasive wear and adhesive wear to abrasive wear when the concentration of Mo exceeds 2.10 wt.%. [ABSTRACT FROM AUTHOR]