Search

Rolling treatments have been identified as a promising fabrication and deformation processing technique for graphene/metal composites with high performance. However, it is still a challenge to choose appropriate rolling parameters to achieve high strength, ductility and electrical conductivity of the composite simultaneously. In this study, graphene/Cu composites were prepared with an in situ growth method and rolling treatment. The effects of rolling deformation and temperature on the microstructural evolution of graphene and Cu grains, interface bonding between graphene and the matrix, mechanical and electrical properties were systemically investigated. The cold-rolled composite with 85% deformation displayed a maximum ultimate strength of 548 MPa, a high elongation of 8.8% and a good electrical conductivity of 86.2% IACS. This is attributed to oriented graphene arrangement and matrix grain refinement. Our research provides a comprehensive understanding for the rolling behavior of graphene/Cu composites, and can promote the development of graphene-based composites with high performance. [ABSTRACT FROM AUTHOR]

A weldable Al–Mg–Zn–Sc alloy was produced using vacuum induction melting and an argon-protected casting method to achieve high strength and ductility, and the effects of heat treatment on the microstructure evolution and mechanical properties of Al–Mg–Zn–Sc alloys were comparatively investigated. The results reveal that fine equiaxed grains with an average grain size of 40 μm in an as-cast Al–Mg–Zn–Sc alloy change little after heat treatments, bringing about a grain-boundary strengthening of 46.1 MPa. The coarse T-Mg32(Al, Zn)49 phases at grain boundaries are completely dissolved into the matrix through solid-solution treatment, and T-Mg32(Al, Zn)49 with diameters ranging from 10 to 25 nm and Al3Sc with diameters ranging from 5 to 20 nm gradually precipitate during the artificial aging process. The Mg solid solubility is 4.67% in the as-cast Al–Mg–Zn–Sc alloy, and it increased to 5.33% after solid-solution treatment and dramatically decreased to 4.15% after post-aging treatment. The contributions of solid-solution strengthening to as-cast, post-solid-solution and post-aging Al–Mg–Zn–Sc alloys are 78.2 MPa, 85.4 MPa and 72.3 MPa, respectively. The precipitation strengthening of the post-aging alloy is 49.7 MPa, which is an increase of 21% in comparison to that of both as-cast and post-solid-solution alloys. The alloy achieves an optimal tensile strength of 355.3 MPa, yield strength of 175 MPa and elongation of 22% after undergoing solid-solution treatment. [ABSTRACT FROM AUTHOR]

Three-dimensional porous network encapsulation strategy is an effective means to obtain composite phase-change materials (PCMs) with high heat storage capacity and enhanced thermal conductivity. Herein, macroporous reduced graphene oxide (rGO) aerogels with adjustable pore size are prepared by the emulsion template method and hydrothermal reduction process. Further, the shape-stabilized rGO-aerogel-based composite PCMs are constructed after the combination of 3D porous rGO supports and paraffin wax (PW) through vacuum melting infiltration. By regulating the pore structure of the rGO aerogel network, the rGO-based composite PCMs achieve excellent energy storage properties with a phase-change enthalpy of 179.94 J/g for the loading amount of 95.61 wt% and an obvious enhancement in thermal conductivity of 0.412 W/m−1·K−1, which is 54.89% higher than pristine PW and enduring thermal cycling stability. The obtained macroporous rGO-aerogel-based composite PCMs with high thermal storage and heat transfer performance effectively broaden the application of PCMs in the field of thermal energy storage. [ABSTRACT FROM AUTHOR]

The internal coupled electromagnetic melt treatment (ICEMT) method is firstly proposed to produce high-quality and large-sized aluminum alloy billets. A three-dimensional model was established to describe the ICEMT process of direct chill casting (DC casting). The effect of ICEMT on the fluid flow patterns and temperature field in the DC casting of ϕ880 mm AA2219 billets is numerically analyzed. Moreover, the mechanisms of the ICEMT process on grain refinement and macrosegregation were discussed. The calculated results indicate that the electromagnetic field appears to be coupled circinate at the cross section of the melt, the fluid flow becomes unstable accompanied by the bias flow, and the temperature profiles are significantly more uniform. An experimental verification was conducted and the results prove that compared with traditional direct chill casting, the microstructures of the AA2219 large-scale billet under the ICEMT process are uniform and fine. [ABSTRACT FROM AUTHOR]

The requirements of high-strength, wear-resistance and lightweight of brake drums have been continually increasing in recent years and any specific aluminum alloy or particle-reinforced aluminum matrix composites may not satisfy all the demands. Combining dissimilar materials to play their respective advantages is a solution to this problem. In this study, a compound casting method was used to combine solid SiCp/A357 composite and a liquid 7050 aluminum alloy to prepare an aluminum matrix composite with a layered structure. The ProCAST numerical simulation software was used to predict the heat transfer in compound casting process and guide the preheating temperature of the wear-resistant ring in the experiment. An Optical Microscope (OM) and Scanning Electron Microscope (SEM) were used to observe microstructures around the solid–liquid bonding interface, the element distribution and phase component of which were analyzed by Energy Dispersive Spectroscopy (EDS) and mechanical properties were evaluated by microhardness and shear tests. The results showed that the interface of the layered aluminum matrix composite prepared by this method achieved complete metallurgical bonding and a transition zone formed on the solid surface. After T6 heat treatment, the average shear strength of the interface increased from 19.8 MPa to 33.8 MPa. [ABSTRACT FROM AUTHOR]

In this study, large-sized Al–Zn–Mg–Cu alloy billets were prepared by direct chill casting imposed with annular electromagnetic stirring and intercooling; a process named uniform direct chill casting. The effects of uniform direct chill casting on grain size and the alloying element distribution of the billets were investigated and compared with those of the normal direct chill casting method. The results show that the microstructures were refined and the homogeneity of the alloying elements distribution was greatly improved by imposing the annular electromagnetic stirring and intercooling. In uniform direct chill casting, explosive nucleation can be triggered, originating from the mold wall and dendrite fragments for grain refinement. The effects of electromagnetic stirring on macrosegregation are discussed with consideration of the centrifugal force that drives the movement of melt from the central part towards the upper-periphery part, which could suppress the macrosegregation of alloying elements. The refined grain can reduce the permeability of the melt in the mushy zone that can restrain macrosegregation. [ABSTRACT FROM AUTHOR]

High-strength aluminum alloy (mainly refers to the 7xxx series) is the optimum material for lightweight military equipment. However, this type of aluminum alloy is a wrought aluminum alloy. If it is directly formed by traditional casting methods, there will inevitably be problems such as coarseness, unevenness, looseness, and hot cracking in the structure, which will greatly affect the final performance of the part. Based on the internal cooling with annular electromagnetic stirring (IC-AEMS) method, a new technology of rheological die forging is developed in this paper, and the scale-reduced parts of a brake hub of Al-6.54Zn-2.40Cu-2.35Mg-0.10Zr aluminum alloy were prepared. The influence of IC-AEMS and the addition of rare element Sc on the structure and mechanical properties of the parts was studied. An optical microscope and scanning electron microscope (SEM) were used to observe the microstructure evolution, energy dispersive spectroscopy (EDS) was used to analyze the phase distribution and composition, and the mechanical properties of the parts were tested by uniaxial tensile tests. The results show that the addition of Sc element can effectively refine the grains and improve the strength and elongation of the material; the application of IC-AEMS improves the cooling rate of the melt, increases the effective nucleation rate, and the grains are further refined. Through process optimization, scale-reduced parts of a brake hub with good formability and mechanical properties can be obtained, the ultimate tensile strength is 597.2 ± 3.1 MPa, the yield strength is 517.8 ± 4.3 MPa, and the elongation is 13.7 ± 1.3%. [ABSTRACT FROM AUTHOR]

There are two critical stages of grain refinement during solidification: above and below the liquidus temperature. The key to improve the refinement potential is ensuring the nucleation sites precipitate in large quantities and dispersed in the melt above liquidus. In this work, internal cooling with annular electromagnetic stirring was applied to an Al-Zn-Mg-Cu-Zr alloy at a temperature above liquidus. A systematic experimental study on the grain refining potential was performed by combining different melt treatments and pouring temperatures. The results indicate that internal cooling with annular electromagnetic stirring (IC-AEMS) had a significantly superior grain refining potency for the alloy compared to traditional electromagnetic stirring (EMS). In addition, homogeneous and refined grains were achieved at high pouring temperatures with IC-AEMS. The possible mechanisms for the enhanced grain refinement above the liquidus temperature are explained as the stable chilling layer around the cooling rod in IC-AEMS providing undercooling for the precipitation of Al3Zr nucleant particles and the high cooling rate restraining the growth rate of these particles. At the same time, forced convection promotes a more homogeneous distribution of nucleant particles. [ABSTRACT FROM AUTHOR]

A new type of inhibitor is studied in this paper. Inhibition efficiency and adsorption behavior of an inhibitor film on the steel surface is tested via the electrochemical method and theoretical calculation to establish the adsorption model. Test results confirm that inhibition efficiency is improved with the addition of an inhibitor, and the inhibitor film is formed firmly by comparing the characteristic peaks of S and N. Moreover, the micro-zone corrosion progress of Fe in 3.5% invasive NaCl-simulated seawater environment is studied. The results further show that corrosion is initiated under the zone without the inhibitor film, while it is prevented under the protection of the film. By the experiments, it is shown that inhibitor can be adsorbed on the surface of steel stably and has excellent protection performance for reinforced rebar, which can be widely used in concrete structure. [ABSTRACT FROM AUTHOR]

This study presents a modified annular electromagnetic stirring (M-AEMS) melt treatment suitable for a large-volume and high-alloyed aluminum alloy. A 3D computational model coupling an electromagnetic model with a macroscopic heat and fluid-flow model was established by using Ansoft Maxwell 3D and Fluent from ANSYS workbench, and the effects of the electromagnetic shielding ring, the height of the magnet yoke, the shape of the iron core, and the internal cooling mandrel on the electromagnetic, thermal and flow fields were studied numerically. Based on the optimal technical parameters, the effectivity of the M-AEMS process by using 7075 alloy was validated experimentally. The results show that a favorable electromagnetic field distribution can be achieved by changing the magnet yoke height, the iron-core shape and the electromagnetic shielding ring, and the melt temperature of the 7075 alloy can drop rapidly to the pouring temperature by imposing the internal cooling mandrel; compared with ordinary annular electromagnetic stirring, the M-AEMS process creates a lower magnetic strength near the melt top, beneficial for stabilizing the melt surface; meanwhile, it yields a higher magnetic strength near the melt bottom, which increases the shear rate and ensures an optimal stirring effect. Therefore, M-AEMS works more efficiently because the thermal and composition fields become uniform in a shorter time, which reduces the average grain size and the composition segregation, and a more stable melt surface can be obtained during treatment, which reduces the number of air and oxide inclusions in the melt. [ABSTRACT FROM AUTHOR]

The nucleation and grain growth that occur during solidification have been extensively examined, but insight into the influence of an external field on the formation of heterogeneous crystal nuclei above the liquidus remains unclear in the peritectic refinement mechanism. In this work, we studied the effect of cooling rate above the liquidus on the formation of primary Al3Zr and grain refinement in Al-0.2%Zr alloys with inter-cooling annular electromagnetic stirring (IC-AEMS). The results show that the size and distribution of primary Al3Zr are greatly improved, and the morphology transformed from large plate/blocky shapes without IC-AEMS to small blocks with IC-AEMS. Meanwhile, above the liquidus, the addition of an Al-Zr master alloy to pure Al alone did little to enhance the refinement, but after IC-AEMS, the grains were refined dramatically. The refinement result seems to be explained by two hypotheses of pre-nucleation and explosive nucleation. [ABSTRACT FROM AUTHOR]