Search

In this study, the phase field method has been used to study the effect of second phase particles with different shapes and different orientations on the grain growth of AZ31 magnesium alloy, after annealing at 350 °C for 100 min. The results show that the shape of the second phase particles would have an effect on the grain growth; the refinement effect of elliptical particles and rod-shaped particles was similar, and better than the spherical particles; the spatial arrangement direction of the second phase particles had no significant effect on the grain growth. On the other hand, when the microstructure of AZ31 magnesium alloy contained second phase particles with different shapes, the effect of mixing different shapes of second phase particles on the grain refinement was enhanced gradually with the decrease im the volume fraction of spherical particles. [ABSTRACT FROM AUTHOR]

In the past decade, bamboo scrimber has developed rapidly in the field of building materials due to its excellent mechanical properties, such as high toughness and high tensile strength. However, when the applied stress exceeds the ultimate strength limit of bamboo scrimber, cracks occur, which affects the performance of bamboo scrimber in structural applications. Due to the propensity of cracks to propagate, it reduces the load-bearing capacity of the bamboo scrimber material. Therefore, research on the fracture toughness of bamboo scrimber contributes to determining the material's load-bearing capacity and failure mechanisms, enabling its widespread application in engineering failure analysis. The fracture toughness of bamboo scrimber was studied via the single-edge notched beam (SENB) experiment and compact compression (CC) method. Nine groups of longitudinal and transverse samples were selected for experimental investigation. The fracture toughness of longitudinal bamboo scrimber under tensile and compressive loadings was 3.59 MPa·m1/2 and 2.39 MPa·m1/2, respectively. In addition, the fracture toughness of transverse bamboo scrimber under tensile and compressive conditions was 0.38 MPa·m1/2 and 1.79 MPa·m1/2, respectively. The results show that, for this material, there was a significant distinction between longitudinal and transverse. Subsequently, three-point bending tests and simulations were studied. The results show that the failure mode and the force–displacement curve of the numerical simulation were highly consistent compared with the experimental results. It could verify the correctness of the test parameters. Finally, the flexural strength of bamboo scrimber was calculated to be as high as 143.16 MPa. This paper provides data accumulation for the numerical simulation of bamboo scrimber, which can further promote the development of bamboo scrimber parameters in all aspects of the application. [ABSTRACT FROM AUTHOR]

The effect of microstructure on the onset strain and rate of deformation-induced martensitic transformation (DIMT) in Q&P steel is studied by a mean-field micromechanics model, in which the residual austenite (RA) and primary martensite (M) phases are treated as elastoplastic particles embedded into the ferrite (F) matrix. The results show that when the volume fraction of the RA increases with a constant fraction of the M, the onset strain of DIMT increases and transformation rate decreases, in contrast to the case of the RA fraction effect with a fixed F fraction. Increasing the volume fraction of the M postpones the DIMT, regardless of the corresponding change from the RA or F fraction, which is similar to the effect of the RA fraction with the constant M but to a higher degree. Conversely, when increasing the fraction of the matrix F, the onset strain of DIMT increases and the rate decreases, and the effect is greater when the corresponding fraction change comes from the M rather than from the RA. Moreover, when the aspect ratio of the RA increases, the onset strain of DIMT decreases with a gradual increase in transformation rate, in agreement with the experimental observation that the equiaxial austenite is more stable in Q&P steels. However, the aspect ratio effect of the M is opposite to that of the RA, indicating that the lath-shaped primary martensite could protect the austenite from DIMT. [ABSTRACT FROM AUTHOR]

Ceramic-particle-reinforced iron matrix composites (CPR-IMCs) have been used in many fields due to their excellent performance. In this study, using the fast resistance-sintering technology developed by our team, iron matrix composites (IMCs) reinforced by both SiC and TiCx particles were fabricated via the addition of SiC and Ti3AlC2 particles, and the resulting relative densities of the sintering products were up to 98%. The XRD and EDS analyses confirmed the in situ formation of the TiCx from the decomposition of Ti3AlC2 during sintering. A significant hybrid reinforcing effect was discovered in the (SiC + TiCx)p/Fe composites, where the experimental strength and hardness of the (SiC + TiCx)p/Fe composites were higher than the composites of monolithic SiCp/Fe and (TiCx)p/Fe. While, under the condition of constant particle content, the elongation of the samples reinforced using TiCx was the best, those reinforced by SiC was the lowest, and those reinforced by (SiC + TiCx) fell in between, which means the plastic response of (SiC + TiCx)p/Fe composites obeyed the rule of mixture. The successful preparation of IMCs based on the hybrid reinforcement mechanism provides an idea for the optimization of IMCs. [ABSTRACT FROM AUTHOR]

Based on the principle of grain refinement caused by the second-phase particles, a phase field model was built to describe the recrystallization process in the ZK60 alloy system with Y added under applied stress between temperatures 573 and 673 K for 140 min duration. The simulation of grain growth with second phase particles and applied stress during annealing process on industrial scale on the condition of real time-space was achieved. Quantitative analysis was carried out and some useful laws were revealed in ZK60 alloy system. The second phase particles had a promoting effect on the grain refinement, however the effect weakened significantly when the content exceeded 1.5%. Our simulation results reveal the existence of a critical range of second phase particle size of 0.3–0.4 μm, within which a microstructure of fine grains can be obtained. Applied stress increased the grain coarsening rate significantly when the stress was more than 135 MPa. The critical size of the second phase particles was 0.4–0.75 μm when the applied stress was 135 MPa. Finally, a microstructure with a grain size of 11.8–13.8 μm on average could be obtained when the second phase particles had a content of 1.5% and a size of 0.4–0.75 μm with an applied stress less than 135 Mpa after 30 min annealing at 573 K. [ABSTRACT FROM AUTHOR]