Search

(1) Background: After more than a decade since their first description, Inadvertent Tooth Movements (ITMs) remain an adverse effect of orthodontic retainers without a clear etiology. To further investigate the link between ITMs and the mechanical properties of different retainers, the response upon vertical loading was compared in three retainer types (two stainless steel and one nickel–titanium). The influence of different reference teeth was also considered. (2) Methods: Three retainers (R1, R2, R3) were tested in a newly developed biomechanical analysis system (FRANS). They were bonded to 3D-printed models of the lower anterior jaw and vertically displaced up to 0.3 mm. Developing forces and moments were recorded at the center of force. (3) Results: The vertical displacement caused vertical forces (Fz) and labiolingual moments (My) to arise. These were highest in the lateral incisors (up to 2.35 ± 0.59 N and 9.27 ± 5.86 Nmm for R1; 1.69 ± 1.06 N and 7.42 ± 2.65 Nmm for R2; 3.28 ± 1.73 N and 15.91 ± 9.71 Nmm for R3) for all analyzed retainers and with the R3 retainer for all analyzed reference teeth, while the lowest Fz and My values were recorded with the R1 retainer. (4) Conclusions: Displacements of 0.2 mm and larger provided forces and moments which could be sufficient to cause unwanted torque movements, such as ITMs, in all analyzed retainers. Clinicians must be mindful of these risks and perform post-treatment checkups on patients with retainers of all materials. [ABSTRACT FROM AUTHOR]

In the process of directed energy deposition (DED), the grain structure of the deposited samples is determined by two aspects. The first is the initial solidification grain structure; the second is the effect of the upper thermal cycle on the solidified grain structure of the lower layer. Dynamic recrystallization and grain growth can be activated under suitable strain and the temperature resulting from thermal cycles. The evolution of grain size and the geometric dislocation density (GND) of austenitic stainless steel 316 L under different strains and temperatures caused by thermal cycles was investigated. It is found that dynamic recrystallization requires an appropriate level of accumulated strain, temperature, and initial grain size. Under <2% accumulated strain and 400–1200 °C conditions caused by 30 layers of thermal cycles, fully dynamic recrystallization occurs with coarse initial grains (CIG), leading to the complete coarsening of grains. However, relatively fine initial grains (FIG) under the same conditions only display partial dynamic recrystallization. The next 2–4% strain and 400–700 °C by 60 layers of thermal cycles make up the driving force of fully dynamic recrystallization, and the grains coarsen completely. Larger accumulated strain (4–6%) and lower temperature (400–600 °C) by 90 layers of thermal cycles and FIG provide more nucleation sites for dynamic recrystallization, which leads to little coarsening of grains even after fully dynamic recrystallization. Temperature, accumulated strain, and the amount of δ-ferrite promote the formation of sub-grains during dynamic recrystallization caused by thermal cycles, which leads to the increase in GND. [ABSTRACT FROM AUTHOR]

In order to explore the influence of laser power on the evolution of molten pool and convective heat transfer of laser cladding Incoloy 926 on stainless steel surface, a three-dimensional thermal fluid multi-field coupled laser cladding numerical model was established in this paper. The variation of latent heat during solid-liquid phase transformation was treated by apparent heat capacity method. The change in the gas–liquid interface was tracked using the mesh growth method in real time. The instantaneous evolution of temperature field and velocity flow field of laser cladding Incoloy 926 on a stainless steel surface under different laser power was discussed. The solidification characteristic parameters of the cladding layer were calculated based on the temperature-time variation curves at different nodes. The mechanism of the impact of laser power on the microstructure of the cladding layer was revealed. The experiment of laser cladding Incoloy 926 on 316L surface was carried out under different laser power. Combined with the numerical simulation results, the effects of laser power on the geometrical morphology, microstructure and element distribution of the cladding layer were compared and analyzed. The results show that with the increase in laser power, the peak temperature and flow velocity of the molten pool surface both increase significantly. The thermal influence of the molten pool center on the edge is enhanced. The temperature gradient, solidification rate, and cooling rate increased gradually. The microstructure parameters (G/R) are relatively small when the laser power is 1000 W. In the experimental range, the dilution rate and wetting angle of the cladding layer both increase with the increase in laser power. When the laser power is 1000 W, the alloying elements of the cladding layer are more evenly distributed and the microstructure is finer. The experimental results are in good agreement with the simulation results. [ABSTRACT FROM AUTHOR]

The presentation of a constitutive model could help researchers to predict the mechanical behavior of a material, which also contributes to the further generalization of the material. This paper is to explore the tensile constitutive model of engineered cementitious composites (ECCs) reinforced by high-strength steel wire mesh based on experiments and numerical simulations. DIANA was used to simulate the tensile process of the specimens, and experiments were carried out to validate the numerical model. The effect of the ECCs' tensile strength, reinforcement ratio and specimen size were considered during the specimen design process. The results showed that most of the errors of the simulated values compared to the experimental results were within 5%, which proved that the numerical model was quite accurate. The proposed constitutive model revealed the different roles played by ECCs and high-strength steel wires at different stress stages, and the calculation results were in high agreement with the simulation results, indicating the effectiveness of the constitutive model. The study in this paper could provide an important reference for the popularization and application of ECCs reinforced by high-strength steel wire mesh. [ABSTRACT FROM AUTHOR]

This study focused on standard Compact Tension (CT) specimens and two loading modes during the numerical analyses carried out, namely: pure mode I and mixed-mode loading (Modes I+II). Numerical stress intensity factors, KI, were calculated using Abaqus® 2022 and compared with those given analytically under pure mode I loading, showing very good agreement. Additionally, KI, KII, and KIII results obtained from Abaqus® were presented for mixed-mode loading, analyzing crack growth and variation through the thickness of the CT specimen. Moreover, fatigue crack growth simulations under mode I loading were conducted on standard CT specimens using the Extended Finite Element Method (XFEM) and the Paris Law parameters of an AISI 316L stainless steel. It was shown that XFEM effectively determines crack propagation direction and growth, provided that an appropriate mesh is implemented. [ABSTRACT FROM AUTHOR]

The oxide layer development of X6CrNiNb18-10 (AISI 347) during exposure to high-temperature water has been investigated. Stainless steels are known to form a dual oxide layer in corrosive environments. The secondary Fe-rich oxide layer has no significant protective effect. In contrast, the primary Cr-rich oxide layer is known to reach a stabilized state, protecting the base metal from further oxidation. This study's purpose was to determine the development of oxide layer dimensions over exposure time using SEM, TEM and EDX line scans. While a parabolic development of Cr in the protective primary layer and Fe in the secondary layer was observed, the dimensions of the Ni layer remained constant. Ni required the presence of a pronounced Fe-rich secondary layer before being able to reside on the outer secondary layer. With increasing immersion time, the Ni element fraction surpassed the Cr element fraction in the secondary layer. Oxide growth on the secondary layer could be observed. After 480 h, nearly the entire surface was covered by the outer oxide layer. In the metal matrix, no depletion of Cr or Ni could be observed over time; however, an increased presence of Cr and Ni in the primary layer was found at the expense of Fe content. The Nb-stabilized stainless steel was subject to the formation of Niobium pentoxide (Nb2O5), with the quantity and magnitude of element fraction increasing over exposure time. [ABSTRACT FROM AUTHOR]

This article discusses special additive technologies, with a particular focus on the innovative binder jetting technology used to create three-dimensional objects. The theoretical part of this article defines the production process–its shortcomings and benefits. Also, the article describes process parameters and individual steps that must be optimally set for the desired result. Further, the article characterizes the most influential factors that are indispensable in the printing process-metallic powder, binder, printing parameters, and finishing operations after the printing itself. The conclusion of the theoretical part deals with various material possibilities when using binder jetting technology. In the practical part of the article, the properties of the material, the chemical composition, and the resulting accuracy of the printed samples will be verified experimentally. The information obtained will subsequently be used to identify an economically advantageous application of binder jetting technology. [ABSTRACT FROM AUTHOR]

Hollow sinking experiments and tensile tests were conducted to clarify the evolution of surface roughness during hollow sinking. Stainless steel tubes (outer diameter: 1.5 mm; wall thickness: 0.045 mm) featuring a single grain spanning the wall thickness achieved via annealing as the starting material. The tube was drawn without an internal tool using a draw bench by controlling the tube drawing speed ratio of the die entrance and exit sides. The surface roughnesses of the inner and outer surfaces at the die entrance and exit sides of the drawn tube were compared with the surface roughnesses of the inner and outer surfaces under the uniaxial tensile deformation of the starting material. As a result, two major findings were revealed; the surface roughness formation behavior during the hollow sinking; the uniaxial tensile deformation exhibits a tube on both sides of the entrance and the exit of a die. Former uniaxial tensile deformation forms surface roughness of the tube at the die-entrance-side. However, hollow sinking reduces the roughness. The tube keeps its small roughness even though it is applied the later uniaxial tensile deformation behind the die exit. Furthermore, the conventional formula to predict the surface roughness of a metal sheet caused by the uniaxial tensile deformation can predict the surface roughness of a tube in the hollow sinking. At both die entrance and exit sides, the roughness of the inner surface was larger than that of the outer surface at the die entrance and exit side. The outer surface of the tube contacts the inside of a die when the tube passes through the die. The height of the convex parts decreased at that moment. Hollow sinking suppressed the increase in surface roughness of the inner surface as the outer surface was smoothed in the die. However, due to the formation of surface roughness after leaving the die, there is an overall increasing trend in inner surface roughness. [ABSTRACT FROM AUTHOR]

For space missions to either the Moon or Mars, protecting mechanical moving parts from the abrasive effects of prevailing surface dust is crucial. This paper compares the abrasive effects of two lunar and two Martian simulant regoliths using special pin-on-disc tests on a stainless steel/polytetrafluoroethylene (PTFE) sealing material pair. Due to the regolith particles entering the contact zone, a three-body abrasion mechanism took place. We found that friction coefficients stabilised between 0.2 and 0.4 for all simulants. Wear curves, surface roughness measurements, and microscopic images all suggest a significantly lower abrasion effect of the Martian regoliths than that of the lunar ones. It applies not only to steel surfaces but also to the PTFE pins. The dominant abrasive micro-mechanism of the disc surface is micro-ploughing in the case of all tests, while the transformation of the counterface is mixed. The surface of pin material is plastically transformed through micro-ploughing, while the material is removed through micro-cutting due to the slide over hard soil particles. [ABSTRACT FROM AUTHOR]

This work covers the formation of a passive state for two different alloys used in the aeronautical industry. The aim of this study is to investigate the effectiveness of passivation treatments on 17-7PH and 410 SS (stainless steel) samples, specifically when performed with citric and nitric acid solutions at 49 °C using an immersion time of 90 min and subsequent exposure in 3.5 wt.% NaCl solution. Employing the cyclic potentiodynamic polarization (CPP) technique, the corrosion properties of the passivated material were evaluated according to the ASTM G65-11 standard. A microstructural analysis was performed using scanning electron microscopy (SEM). The passivated layer was characterized via X-ray photoelectron spectroscopy. In the results, the CPP curves showed positive hysteresis, indicating pitting localized corrosion, and 17-7PH steel passivated at 49 °C for 90 min in citric acid exhibited lower corrosion rate values equivalent to ×10−3 mm/year. [ABSTRACT FROM AUTHOR]

The characterization and evolution of corrosion products deposited on/around MnSs, a typical kind of inclusive particle embedded in AISI 304 stainless steel, was analyzed using a quasi-in-situ method in a 3.5 wt.% NaCl solution. On/around the MnS inclusion, a corrosion product layer with spinel Fe3−xCrxO4 as the main component was formed, with a thickness of several hundred nanometers. Below the layer, there was a cavity layer in which part of the MnS remained, forming secondary pitting along the MnS/matrix boundary. The mechanism of corrosion product deposition and evolution accompanied by MnS dissolution, as well as the characteristics of the corrosion products, are discussed. [ABSTRACT FROM AUTHOR]

In order to facilitate the application of underwater laser welding technology in in situ repairs of nuclear power plants, this study conducted comparative experiments between local dry underwater laser welding and laser welding in air on 304NG nitrogen-controlled stainless steel. The aim was to explore its microstructural evolution and mechanical properties in underwater environments. It was found that, near the fusion line of laser welding in air, columnar dendrites gradually evolved into cellular dendrites toward the weld center, eventually disappearing, resulting in a skeletal ferrite and serrated austenite structure. The underwater laser welding joints exhibited similar characteristics yet with more pronounced alternation between columnar and cellular dendrites. Additionally, the size of cellular dendrites decreased significantly, and needle-like ferrite was observed at the weld center. The hardness of underwater laser welded joints was slightly higher than that of in-air laser welded joints. Compared to laser welding in air, the strength of underwater laser welding joints increased from 443 MPa to 471 MPa, and the displacement increased from 2.95 mm to 3.45 mm, both types of welded joints exhibited a mixed mode fracture characterized by plasticity and brittleness. [ABSTRACT FROM AUTHOR]

High-carbon–chromium martensitic stainless steel (MSS) is widely used in many fields due to its excellent mechanical properties, while the coarse eutectic carbide in MSS deteriorates corrosion resistance. In this work, nitrogen was added to the MSS to improve corrosion resistance. The effects of nitrogen on the microstructure and corrosion resistance of MSS were systematically studied. The results showed that the addition of nitrogen promoted the development of Cr2N and reversed austenite, effectively inhibiting the formation of δ-ferrite. Therefore, the durability of the passivation film was improved, the passivation zone was expanded, and the susceptibility to metastable pitting was decreased. As a consequence, nearly two orders of magnitude have been achieved in the pitting potential (Epit) of MSS containing nitrogen, and the polarization resistance value (Rp) has gone up from 4.05 kΩ·cm2 to 1.24 × 102 kΩ·cm2. This means that in a corrosive environment, nitrogen-treated MSS stainless steel is less likely to form pitting pits, which further extends the service life of the material. [ABSTRACT FROM AUTHOR]

In this study, we optimized the parameters of diffusion bonding on multi-layered stainless steel 316L and 430 stacks. The preparation process for diffusion bonding is crucial, as the bonding surfaces need to be polished and meticulously cleaned to ensure a smooth bonding process. We fabricated twelve-layer plates consisting of 55 mm × 55 mm × 3 mm and 100 mm × 50 mm × 3 mm dimensions, and the bonding response was investigated by evaluating the tensile strength of the bonding zone under varying bonding conditions, with a bonding temperature ranging from 1000 to 1048 °C, a bond time ranging from 15 to 60 min, pressure ranging from 10 to 25.3 MPa, and under a vacuum environment. SS430 exhibits a significantly higher compression creep rate than SS316L. The compressibility of diffusion welding materials does not impact the diffusion bonding strength. Multi-axial tensile strength tests confirmed strong bonding joint strength in various axes. The tensile strengths of monolithic and Diffusion bonding (DB) specimens tested in parallel are essentially identical. The optimized diffusion bonding parameters (Condition G2C: 1048 °C/25.3 MPa/15 min) are ideal for producing SS316L stainless steel cores in compact heat exchangers, offering a superior bonding quality and reduced costs. These findings have practical implications for the production of stainless steel cores in compact heat exchangers, demonstrating the relevance and applicability of our research. [ABSTRACT FROM AUTHOR]

In this study, to improve the fatigue strength of the LDED (laser-directed energy deposition) 316L stainless steel, an in situ ultrasonic rolling technology is developed to assist the laser-directed energy deposition process (LDED-UR). The microstructural characteristics and fatigue behavior are comprehensively discussed. The results show that the average size of pores of the LDED-UR alloy is about 10.2 μm, which is much smaller than that of the LDED alloy (34.1 μm). Meanwhile, the density of the LDED alloy is also enhanced from 98.26% to 99.27% via the in situ ultrasonic rolling. With the application of the in situ ultrasonic rolling, the grains are transformed into fully equiaxed grains, and their average grain size is greatly reduced from 84.56 μm to 26.93 μm. The fatigue limit of the LDED-UR alloy is increased by 29% from 210 MPa (LDED alloy) to 270 MPa, which can be ascribed to the decreased porosity and the fine grains. In particular, the crack initiation site of the LDED alloy is located at the surfaces, while it is nucleated from the sub-surface for the LDED-UR alloy. This is mainly attributed to the compression residual stress induced by the in situ ultrasonic rolling. This research offers a valuable understanding of the failure mechanisms in additively manufactured metals, guiding the development of effective strategies to improve their fatigue threshold under severe operating conditions. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM) is a technology that builds parts layer by layer. Over the past decade, metal additive manufacturing (AM) technology has developed rapidly to form a complete industry chain. AM metal parts are employed in a multitude of industries, including biomedical, aerospace, automotive, marine, and offshore. The design of components can be improved to a greater extent than is possible with existing manufacturing processes, which can result in a significant enhancement of performance. Studies on the anisotropy of additively manufactured metallic materials have been reported, and they describe the advantages and disadvantages of preparing different metallic materials using additive manufacturing processes; however, there are few in-depth and comprehensive studies that summarize the microstructural and mechanical properties of different types of additively manufactured metallic materials in the same article. This paper begins by outlining the intricate relationship between the additive manufacturing process, microstructure, and metal properties. It then explains the fundamental principles of powder bed fusion (PBF) and directed energy deposition (DED). It goes on to describe the molten pool and heat-affected zone in the additive manufacturing process and analyzes their effects on the microstructure of the formed parts. Subsequently, the mechanical properties and typical microstructures of additively manufactured titanium alloys, stainless steel, magnesium–aluminum alloys, and high-temperature alloys, along with their anisotropy, are summarized and presented. The summary indicates that the factors leading to the anisotropy of the mechanical properties of metallic AM parts are either their unique microstructural features or manufacturing defects. This anisotropy can be improved by post-heat treatment. Finally, the most recent research on the subject of metal AM anisotropy is presented. [ABSTRACT FROM AUTHOR]

The Z-pinch device is a critical component in inertial confinement fusion, where stainless steel electrodes must withstand high current densities of up to MA/cm2. Gases and difficult-to-remove impurities adhering to the electrode surfaces can ionize, significantly impacting the device's electrical conductivity efficiency. In this paper, the surface of stainless steel electrodes was subjected to cleaning using a large-area plasma jet under atmospheric pressure. The wettability, chemical composition, and chemical state of the electrode surface were characterized using a water contact angle measuring instrument and X-ray photoelectron spectroscopy (XPS). The cleaning effect under different discharge parameters was systematically analyzed. The results revealed a significant reduction in the content of carbon pollutants on the surface of stainless steel electrodes, decreasing from 62.95% to a minimum of 37.68% after plasma cleaning. Moreover, the water contact angle decreased from 70.76° to a minimum of 29.31°, and the content of water molecules adsorbed on the surface decreased from 17.31% to a minimum of 5.9%. Based on the evolution process of micro-element content and chemical state on the surface of stainless steel electrode, the cleaning process of adhering substances on the surface by atmospheric pressure plasma was analyzed by the layered cleaning model for surface pollutants on stainless steel. [ABSTRACT FROM AUTHOR]

In this paper, a Cr coating was prepared by induction heating and pack-cementation chromizing on AISI 304 austenitic stainless steel. Then, the cold-rolling deformation and annealing treatment were introduced to refine the coarse matrix grains caused by pack-chromizing and improve the overall performance of 304 austenitic stainless steel. The phase composition, element distribution, and microstructure of the coating were carefully characterized. The microhardness, wear resistance, and corrosion resistance of the coating were tested. The results show that the Cr coating with a thickness of 100 μm is mainly composed of a (Cr,Fe)23C6, (Cr,Fe)7C3, and α-Fe-Cr solid solution. After the cold-rolling deformation and subsequent annealing treatment, the grains are significantly refined and the Cr coating is divided into two layers, consisting of carbon-chromium compounds such as Cr23C6, Cr7C3, Cr2C, and Cr3C2 in the surface layer and a Fe-Cr solid solution in the subsurface layer. The cold-rolling deformation and annealing treatment significantly improved the microhardness and wear resistance of the coated sample, and the corrosion resistance was also better than that of the uncoated sample. [ABSTRACT FROM AUTHOR]

The oxidation behaviour of iron-based 316L stainless steel was investigated in the temperature range of 700 to 1000 °C. The test specimens in the shape of plates were produced by selective laser melting. After fabrication, the samples were sandblasted and then annealed in air for different periods of time (0.5, 2, 8, 32 h). Under the influence of temperature and time, stainless steels tend to form an oxide layer. Scanning electron microscopy, energy dispersive analysis, and X-ray diffraction were employed to analyse the composition of this layer. Notably, a thin oxide layer primarily composed of (Fe-Cr) formed on the surface due to temperature effects. In addition, with increasing temperature (up to 1000 °C), the oxide of the main alloying elements, specifically Mn2(Fe-Cr)O4, appeared alongside the Fe-Cr oxide. Furthermore, the samples were subjected to conversion X-ray (CXMS) and conversion electron (CEMS) Mössbauer spectroscopy. CXMS revealed a singlet with a decreasing Mössbauer effect based on the surface metal oxide thickness. CEMS revealed the presence of Fe3+ in the surface layer (0.3 µm). Moreover, an interesting phenomenon occurred at higher temperature levels due to the inhomogeneously thick surface metal oxide layer and the tangential direction of the Mössbauer radiation towards the electron detector. [ABSTRACT FROM AUTHOR]

Friction stir welding was utilized to obtain high-quality SUS301L stainless steel joints, whose mechanical and corrosion properties were thoroughly evaluated. Sound joints were obtained with a wide range of rotational velocities from 400 to 700 rpm. The microstructures of the stir zone primarily consisted of austenite and lath martensite without the formation of detrimental phases. The ultimate tensile strength of the welded joints improved with higher rotational velocities apart from 400 rpm. The ultimate tensile strength reached 813 ± 16 MPa, equal to 98.1 ± 1.9% of the base materials (BMs) with a rotational velocity of 700 rpm. The corrosion resistance of the FSW joints was improved, and the corrosion rates related to uniform corrosion with lower rotational velocities were one order of magnitude lower than that of the BMs, which was attributed to the lower martensite content. However, better anti-pitting corrosion performance was obtained with a high rotational velocity of 700 rpm, which was inconsistent with the uniform corrosion results. It could be speculated that a higher martensitic content had a negative effect on the uniform corrosion performance, but had a positive effect on the improvement of the anti-pitting corrosion ability. [ABSTRACT FROM AUTHOR]

The main objective of this work was to propose and evaluate a methodology for shielding-gas selection in additive manufacturing assisted by wire arc additive manufacturing (WAAM) with an austenitic stainless steel as feedstock. To validate the proposed methodology, the impact of multi-component gases was valued using three different Ar-based blends recommended as shielding gas for GMA (gas metal arc) of the target material, using CMT (cold metal transfer) as the process version. This assessment considered features that potentially affect the building of the case study of thin walls, such as metal transfer regularity, deposition time, and geometrical and metallurgical characteristics. Different settings of wire-feed speeds were conceived to maintain a similar mean current (first constraint for comparison's sake) among the three gas blends. This approach implied different mean wire-feed speeds and simultaneously forced a change in the deposition speed to maintain the same amount of material deposited per unit of length (second comparison constraint). The composition of the gases affects the operational performance of the shielding gases. It was concluded that by following this methodology, shielding-gas selection decision-making is possible based on the perceived characteristics of the different commercial blends. [ABSTRACT FROM AUTHOR]

Taking austenitic stainless-steel bellows as the research object, a finite element model for the heat treatment of austenitic stainless-steel bellows was constructed based on ABAQUS CAE 2022. The physical properties of the bellows after the heat treatment were analyzed using experimental and simulated curve processing analysis methods. The changes in residual stress and deformation in relation to the bellows under different cooling times were explored, as well as the distribution of residual stress and deformation at a certain cooling time. The results show that as the cooling time of the heat treatment increases, the residual stress of the bellow decreases significantly, the reduction rate accelerates, and the degree of deformation gradually decreases. When the cooling time of the heat treatment is 900 s, the residual stress of the wave peak in the middle position of the bellow is relatively small, and the residual stress value of the wave valley along the axis direction does not change significantly. The deformation degree of the wave peak and valley axis direction is relatively uniform. [ABSTRACT FROM AUTHOR]

In the process of particle erosion and electrochemical corrosion interaction, the electrolyte flow state change, product film destruction, and matrix structure change caused by particle impact affect the electrochemical corrosion process. Such transient, complex physical and electrochemical changes are difficult to capture because of the short duration of action and the small collision area. The peak, step time, and recovery time in this transient step cycle can indirectly reflect the smoothness and reaction rate of the electrochemical reaction system, and thus characterize the resistance to scouring corrosion coupling damage of metals in liquid–solid two-phase flow. In this study, in order to obtain the electrochemical response at the moment of particle impact, electrochemical monitoring experiments using a specially designed miniature three-electrode system were used to test step-critical values, including step potential, current, and resistance, among others. Meanwhile, an electrochemical step model under particle impact considering boundary layer perturbation was developed. The experimental results reflect the effect law of particle impact velocity and particle size on the peak step and recovery period. Meanwhile, the effect of particle impingement on the electrochemical step of stainless steel in different electrolyte solutions was obtained by comparing the step curves in distilled water and Cl-containing water. The connection between the parameters in the electrochemical step model and in the particle impact, as well as the effect of the variation of these parameters on the surface repassivation process are discussed in this paper. By fitting and modeling the test curves, a new mathematical model of electrochemical step-decay under single-particle impact was obtained, which can be used to characterize the change pattern of electrochemical parameters on the metal surface before and after the impingement. [ABSTRACT FROM AUTHOR]

Hot forming is an effective approach for improving the formability of ultrathin metal sheets, such as those made of stainless steel and pure titanium. However, the increased friction coefficient between the tool and the high-temperature metal sheet negatively affects material flow during hot forming, potentially resulting in severe local thinning or even cracking. This study explores the frictional behavior of 0.1 mm thick ferritic stainless steel (FSS) and commercially pure titanium (CP-Ti) sheets at elevated temperatures. A friction testing apparatus was developed to measure the friction coefficients of these metal sheets from room temperature (25 °C) up to 600 °C. The friction coefficient of the FSS sheet increased monotonically with temperature, whereas that of the CP-Ti sheet first increased and then decreased. Post-friction testing microscopic examination demonstrated that built-up edges formed on the surfaces of the friction blocks when rubbed against the stainless steel, contributing to the higher friction coefficients. This study provides a foundation for understanding frictional behavior during the hot forming of ultrathin metal sheets. [ABSTRACT FROM AUTHOR]

Stainless steel grade 430 is a type of soft magnetic electromagnetic material with rapid magnetization and demagnetization properties. Considering the delay phenomenon during operation, this study selected 430 stainless steel as the material and explored various metallurgical methods such as magnetic annealing and the addition of Mo as well as increasing the Si content to investigate the microstructure, mechanical behavior, and magnetic properties of each material, aiming to improve the magnetic properties of 430 stainless steel. Experimental results showed that the four electromagnetic steel materials (430F, 430F-MA, 434, and KM31) had equiaxed grain matrix structures, and excellent tensile and elongation properties were observed for each specimen. Additionally, the magnetic properties of the 430F specimen were similar under the DC and AC-10 Hz conditions. According to the hysteresis curves under different AC frequencies (10, 100, 1000 Hz), both magnetic annealing and the addition of Mo could reduce the Bm, Br, and Hc values of the raw 430F material. Increasing the Si content resulted in a decrease in Hc values and an increase in Bm and Br values. [ABSTRACT FROM AUTHOR]

The presented manuscript focuses on the influence of process parameters of abrasive water jet technology on the creation of non-transient erosive grooves. The processed stainless steel SS 316L is additively manufactured using the selective laser melting (SLM) method. Due to the distinct mechanical properties of this material resulting from the production process, the material was machined in two planes according to the direction of the printing layers. The experimental part employed a planned experiment utilizing the DoE (Design of Experiment) method. Experiments aimed at varying process parameters (traverse speed, standoff distance, abrasive mass flow) were conducted at a water pressure of 50 MPa, assessing the parameters' impact on the removed material and the properties of the resulting non-transient erosion groove. The properties of the erosion groove, such as shape and the material removal (area of erosion groove), were evaluated. The influences of process parameters on the observed parameters were assessed using the analysis of variance (ANOVA) method. Experiment preparation and setup were based on a thorough theoretical analysis of the machining process with the abrasive water jet (AWJ) method. The experiment also highlights the diverse properties of the SS 316L material prepared using the SLM method when machined with AWJ technology. [ABSTRACT FROM AUTHOR]

Refractory materials containing calcium aluminate cement (CAC) are commonly used in the metallurgical and petrochemical industries due to their exceptional mechanical resistance, even at temperatures exceeding 1000 °C, and do not require additional reinforcement. This study seeks to advance this practice by developing ultra-high-performance structures that offer building protection against fire and explosions. Such structures require bar reinforcement to withstand accidental tension stresses, and the bond performance becomes crucial. However, the compressive strength of these materials may not correlate with their bond resistance under high-temperature conditions. This study investigates the bond behavior of ribbed stainless austenitic steel bars in refractory materials typical for structural projects. The analysis considers three chamotte-based compositions, i.e., a conventional castable (CC) with 25 wt% CAC, a medium-cement castable (MCC) with 12 wt% CAC, a low-cement castable (LCC), and a low-cement bauxite-based castable (LCB); the LCC and LCB castables contain 7 wt% CAC. The first three refractory compositions were designed to achieve a cold compressive strength (CCS) of 100 MPa, while the LCB mix proportions were set to reach a CCS of 150 MPa. Mechanical and pull-out tests were conducted after treatment at 400 °C, 600 °C, 800 °C, and 1000 °C; reference specimens were not subjected to additional temperature treatment. This study used X-ray fluorescence (XRF), X-ray diffraction (XRD), and scanning electron microscopy (SEM) methods to capture the material alterations. The test results indicated that the bonding resistance, expressed in terms of the pull-out deformation energy, did not directly correlate with the compressive strength, supporting the research hypothesis. [ABSTRACT FROM AUTHOR]

In this work, the potential of magnetron sputtering, as well as cathodic arc evaporation, is investigated with regard to its suitability as a bipolar plate coating of a PEM fuel cell. For this purpose, Cr and Ti thin films were deposited onto a 0.1 mm SS316L by varying the power and bias voltage. The surface structure and thickness of the coatings are examined via SEM and tactile profilometry. Moreover, the coating variants are compared with each other based on the electrical and electrochemical properties relevant to bipolar plates. The sputtered Cr thin films achieve the lowest contact resistance values and exhibit a columnar structure with a smooth surface. Regarding the electrochemical properties, titanium deposited via cathodic arc evaporation has a low current density in the passive region and high breakthrough potential. All in all, both deposition techniques have their individual advantages for the preparation of bipolar plates' coatings. However, Ti thin films prepared via cathodic arc seem to be the most suitable option due to the combination of a high deposition rate, a low cost and good coating properties. [ABSTRACT FROM AUTHOR]

Ultra-thin 304 stainless steel can be used to flexibly display substrates after they have been subjected to chemical mechanical polishing (CMP). The thickness of the chemical oxide layer directly affects the polishing efficiency and surface quality of 304 stainless steel. In the study presented in the following paper, the thickness variation of the chemical oxide layer of 304 stainless steel was analyzed following electrochemical corrosion under different oxidant concentration conditions. Furthermore, the impact of the oxidant concentration on the grooves, chips, and scratch depth–displacement–load curves was investigated during a nano-scratching experiment. Through this process, we were able to reveal the chemical reaction mechanism between 304 stainless steel materials and oxidizers. The corrosion rate was found to be faster at 8% oxidant content. The maximum values of the scratch depth and elastic–plastic critical load were determined to be 2153 nm and 58.47 mN, respectively. [ABSTRACT FROM AUTHOR]

Current research studies devoted to cutting forces in drilling are oriented toward predictive model development, however, in the case of mechanistic models, the material effect on the drilling process itself is mostly not considered. This research study aims to experimentally analyze how the machined material affects the feed force (Ff) during drilling, alongside developing predictive mathematical–statistical models to understand the main effects and interactions of the considered technological and tool factors on Ff. By conducting experiments involving six factors (feed, cutting speed, drill diameter, point angle, lip relief angle, and helix angle) at five levels, the drilling process of stainless steel AISI1045 and case-hardened steel 16MnCr5 is executed to validate the numerical accuracy of the established prediction models (AdjR = 99.600% for C45 and AdjR = 97.912% for 16MnCr5). The statistical evaluation (ANOVA, RSM, and Lack of Fit) of the data proves that the drilled material affects the Ff value at the level of 17.600% (p < 0.000). The effect of feed represents 44.867% in C45 and 34.087% in 16MnCr5; the cutting speed is significant when machining C45 steel only (9.109%). When machining 16MnCr5 compared to C45 steel, the influence of the point angle (lip relief angle) is lower by 49.198% (by 22.509%). The effect of the helix angle is 163.060% higher when machining 16MnCr5. [ABSTRACT FROM AUTHOR]

Grain boundary (GB) precipitation-induced cracking is a significant issue for S31254 super austenitic stainless steel during hot working. Investigating the deformation behavior based on precipitate morphology and distribution is essential. In this study, continuous smaller and intermittent larger precipitates were obtained through heat treatments at 950 °C and 1050 °C. The microstructure evolution and mechanical properties influenced by precipitates were experimentally investigated using an in situ tensile stage inside a scanning electron microscope (SEM) combined with electron backscatter diffraction (EBSD). The results showed that continuous precipitates at 950 °C had a stronger pinning effect on the GB, making grain rotation difficult and promoting slip deformation in the plastic interval. Continuous precipitates caused severe stress concentration near GB and reduced coordinated deformation ability. Additionally, the crack propagation path changed from transcrystalline to intercrystalline. Furthermore, internal precipitates were a crucial factor affecting the initial crack nucleation position. Interconnected precipitates led to an intergranular fracture tendency and severe deterioration of the material's plasticity, as observed in fracture morphology. [ABSTRACT FROM AUTHOR]

The International Maritime Organization (IMO) is currently rolling out more restrictive regulations in order to achieve net-zero GHG emissions by 2050. In response, the shipping industry is planning to pivot to green energy sources such as hydrogen fuel. However, since hydrogen has an extremely low boiling point (−253 °C), materials for storing liquid hydrogen must be highly resistant to low-temperature brittleness and hydrogen embrittlement. A 316L stainless steel is a typical material that meets these requirements, and various welds have been studied. In this study, 3 pass butt welding was performed by applying the FCAW (flux cored arc welding) process to 10 mm thick ASTM-A240M-316L stainless steel, with the size of the fusion zone and HAZ investigated by mechanical testing and heat transfer FE analysis according to process variables, such as heat input, welding speed, and the number of passes. In all cases, the yield and tensile strengths were about 10% and 3% higher than the base metal, respectively. Furthermore, heat transfer FE analysis showed an average error rate of 1.3% for penetration and 10.5% for width and confirmed the size of the HAZ, which experienced temperatures between 500 °C and 800 °C. [ABSTRACT FROM AUTHOR]

Adhesive bonding has proven to be a reliable method of joining materials, and the development of new adhesives has made it possible to use bonding in a variety of applications. This article addresses the challenges of bonding metals such as the aluminum alloy EN AW-5754 and the stainless steel X5CrNi18-10. In this study, the effects of laser cleaning and texturing on the surface properties and strength of two bonded joints were investigated and compared with mechanical preparation (hand sanding with Scotch-Brite and P180 sandpaper). The bonded joints were tested with three different epoxy adhesives. During the tests, the adhesion properties of the bonded surface were determined by measuring the contact angle and assessing the wettability, the surface roughness parameters for the different surface preparations, and the mechanical properties (tensile lap-shear strength). Based on the strength test results, it was found that bonded joints made of stainless steel had 16% to 40% higher strength than aluminum alloys when using the same adhesive and surface preparation. Laser cleaning resulted in maximum shear strength of the aluminum alloy bond, while the most suitable surface preparation for both materials was preparation with P180 sandpaper for all adhesives. [ABSTRACT FROM AUTHOR]

Cutlery and flatware designs are an everchanging phenomenon of the manufacturing industry. Worldwide hospitality businesses demand perpetual evolution in terms of aesthetics, designs, patterns, colours, and materials due to customers' demands, modernisation, and fierce competition. To thrive in this competitive market, modern fabrication techniques must be flexible, adoptive, fast, and cost effective. For decades, static designs and trademark patterns were achieved through moulds, limiting production to a single cutlery type per mould. However, with the advent of laser engraving and design systems, the whole business of cutlery production has been revolutionised. This study explores the possibility of creating diverse designs for stainless steel 304 flatware sets without changing the entire production process. The research analyses three key laser process parameters, power, scanning speed, and number of passes, and their impacts on the resulting geometry, depth of cut, surface roughness, and material removed. These parameters are comprehensively studied and analysed for steel and zirconia ceramic. The study details the effects of power, scanning speed, number of passages, and fluence on engraved geometry. Fluence (power*number of passages/scanning speed) positively influences outputs and presents a positive trend. Medium power settings and higher scanning speeds with the maximum number of passages produce high-quality, low-roughness optimised cavities with the ideal geometric accuracy for both materials. [ABSTRACT FROM AUTHOR]

In this study, we investigated the micromechanical deformation and damage behavior of commercially extruded and additively manufactured 316L stainless steels (AMed SS316L) by combining experimental examinations and crystal plasticity modeling. The AMed alloy was fabricated using the laser powder bed fusion (LPBF) technique with an orthogonal scanning strategy to control the directionality of the as-fabricated material. Optical microscopy and electron backscatter diffraction measurements revealed distinct grain morphologies and crystallographic textures in the two alloys. Uniaxial tensile test results suggested that the LPBFed alloy exhibited an increased yield strength, reduced elongation, and comparable ultimate tensile strength in comparison to those of the extruded alloy. A microstructure-based crystal plasticity model was developed to simulate the micromechanical deformation behavior of the alloys using representative volume elements based on realistic microstructures. A ductile fracture criterion based on the microscopically dissipated plastic energy on a slip system was adopted to predict the microscopic damage accumulation of the alloys during plastic deformation. The developed model could accurately predict the stress–strain behavior and evolution of the crystallographic textures in both the alloys. We reveal that the increased yield strength in the LPBFed alloy, compared to that in the extruded alloy, is attributed to the higher as-manufactured dislocation density and the cellular subgrain structure, resulting in a reduced elongation. The presence of annealing twins and favorable texture in the extruded alloy contributed to its excellent elongation, along with a higher hardening rate owing to twin–dislocation interactions during plastic deformation. Moreover, the grain morphology and defect state (e.g., dislocations and twins) in the initial state can significantly affect strain localization and damage accumulation in alloys. [ABSTRACT FROM AUTHOR]

In this work, thermomechanical treatment (single-pass rolling at 800 °C and solution treatment) was applied to nuclear-grade hot-rolled austenitic stainless steel to eliminate the mixed grain induced by the uneven hot-rolled microstructure. By employing high-temperature laser scanning confocal microscopy, microstructure evolution during solution treatment was observed in situ, and the effect of single-pass rolling reduction on it was investigated. In uneven hot-rolled microstructure, the millimeter-grade elongated grains (MEGs) possessed an extremely large size and a high Schmid factor for slip compared to the fine grains, which led to greater plastic deformation and increased dislocation density and deformation energy storage during single-pass rolling. During subsequent solution treatment, there were fewer nucleation sites for the new grain, and the grain boundary (GB) was the main nucleation site in MEGs at a lower rolling reduction. In contrast, at a higher reduction, increased uniformly distributed rolling deformation and more nucleation sites were developed in MEGs. As the reduction increased, the number of in-grain nucleation sites gradually exceeded that of GB nucleation sites, and in-grain nucleation preferentially occurred. This was beneficial for promoting the refinement of new recrystallized grains and a reduction in the size difference of new grains during recrystallization. The single-pass rolling reduction of 15–20% can effectively increase the nucleation sites and improve the uniformity of rolling deformation distribution in the MEGs, promote in-grain nucleation, and finally refine the abnormally coarse elongated grain, and eliminate the mixed-grain structure after solution treatment. [ABSTRACT FROM AUTHOR]

Surgical ASTM F139 stainless steel is used for temporary fixtures in the biomedical field. Tribocorrosion is a major concern in this application. The aim of the present work was to study the interplay between tribocorrosion behavior and the surface chemistry of the ASTM F139 stainless steel in phosphate-buffered saline solution (PBS). Sliding wear tests were conducted against alumina balls at different electrochemical potentials: open circuit potential (OCP), cathodic potential (−100 mV versus the OCP), and anodic potentials (+200 mVAg/AgCl and +700 mVAg/AgCl). The normal load was 20 N. The wear volume was estimated based on micrographs obtained from the wear tracks using confocal laser scanning microscopy. Moreover, the wear tracks were also examined by scanning electron microscopy (SEM). The surface chemistry of the ASTM F139 specimens was analyzed by X-ray photoelectron spectroscopy (XPS). The wear volume was dependent on the electrochemical potential, being maximized at +700 mVAg/AgCl. Delamination areas and grooves were observed in the wear tracks. Detailed assessment of the surface chemistry inside the wear tracks allowed identification of the main chemical species and their relative quantities, thus enabling correlation of the passive film composition with the observed tribocorrosion behavior. [ABSTRACT FROM AUTHOR]

In order to increase the utilization rate of stainless steel slag, reduce storage needs, and mitigate environmental impacts, this study replaces a portion of limestone with varying amounts of stainless steel slag in the calcination of Portland cement clinker. The study primarily examines the influence of stainless steel slag on the phase composition, microstructure, compressive strength, and free calcium oxide (ƒ-CaO) content of Portland cement clinker. The results show the following: (1) Using stainless steel slag to calcine Portland cement clinker can lower the calcination temperature, reducing industrial production costs and energy consumption. (2) With an increase in the amount of stainless steel slag, the dicalcium silicate (C2S) and tricalcium silicate (C3S) phases in Portland cement clinker initially increase and then decrease; the C3S crystals gradually transform into continuous hexagonal plate-shaped distributions, while the tricalcium aluminate (C3A) and tetracalcium aluminoferrite (C4AF) crystal structures become denser. When the stainless steel slag content is 15%, the dicalcium silicate and tricalcium silicate phases are at their peak; the C3S crystals are continuously distributed with a relatively dense structure, and C3A and C4AF crystals melt and sinter together, becoming distributed around C3S. (3) As stainless steel slag content increases, the compressive strength of Portland cement clinker at 3 days, 7 days, and 28 days increases and then decreases, while ƒ-CaO content decreases and then increases. When the stainless steel slag content is 15%, the compressive strength at 28 days is at its highest, 64.4 MPa, with the lowest ƒ-CaO content, 0.78%. The test results provide a basis for the utilization of stainless steel slag in the calcination of Portland cement clinker. [ABSTRACT FROM AUTHOR]

The identification of residual stresses (RS) in components made by selective laser melting (SLM) is necessary for subsequent technological optimization. The presented research is devoted to evaluating the influence of the combination of laser power (P), scanning velocity (v) and the rarely considered number of layers (nL) on surface residual stresses in SLM stainless steel SS 316L. Experimental parameters were set based on the Design of Experiment (DoE) method, with follow-up X-ray diffraction (XRD) measurements and data processing using analysis of variance (ANOVA) and regression analysis. The obtained data are a valuable stepping-stone for the subsequent design of research focused on the application of sustainable eco-friendly Abrasive Water Jet (AWJ) peening for RS modification in the evaluated material. [ABSTRACT FROM AUTHOR]

The change in the corrosion activities of SS304 and the carbon steel A36 were studied during their exposure for 30 days to hybrid pumice-Portland cement extract (CE), to simulate the concrete–pore environment. The ionic composition and the initial pH (12.99) of the CE were influenced by the reduction of Portland cement (PC) content, volcanic pumice oxides and alkaline activators. Because of the air CO 2   dissolution, the pH decreased and maintained a constant value ≈ 9.10 (established dynamic ionic equilibrium). The CE promoted the passivation of both steels and their free corrosion potential (OCP) reached positive values. On the surfaces, Fe and Cr oxides were formed, according to the nature of the steel. Over the time of exposure, the presence of chloride ions in the pumice caused a localized pitting attack, and for carbon steel, this fact may indicate an intermediate risk of corrosion. The chloride effect was retarded by the accumulation of SO 4 2 − ions at the steel surfaces. Based on electrochemical impedance (EIS), the polarization resistance (Rp) and the thickness of the passive layers were calculated. Their values were compared with those previously reported for the steels exposed to CEs of Portland and supersulfated cements, and the hybrid cement was considered as a PC "green" alternative. [ABSTRACT FROM AUTHOR]

Glass-to-metal seals are a very important element in the construction of vacuum tubes, electric discharge tubes, pressure-tight glass windows in metal cases, and metal or ceramic packages of electronic components. This paper presents the influence of different pretreatment methods on the high-temperature wettability of 304 stainless steel by high-alumina glass sealing. The pretreatment of the steel included laser surface melting and pre-oxidizing. The bonding characteristics of glass and stainless steel directly depend on the wettability in terms of the measured wetting angle, the type of oxide formed at the stainless steel surface, and the microstructural changes during the manufacturing process. The oxide film thickness on the stainless steel surface was evaluated to determine the optimal parameters. The film was wetted with high-alumina glass powder at different temperatures. The results showed that pre-oxidation decreased the wetting angle from 56.2° to 33.6°, while for the laser-melted surface, the wetting angle decreased from 49.8° to 31.5°. Scanning electron microscopy (SEM) revealed that the oxide film on the laser-melted surface was thicker and denser than that formed on the pre-oxidized surface. The present work shows that laser surface melting has a greater beneficial influence on the wetting and diffusion characteristics of 304 stainless steel sealed by high-alumina glass. [ABSTRACT FROM AUTHOR]

Due to the recurrent starting and stopping operations of automobiles during service, their engines' hot ends are continually subjected to high-temperature cyclic oxidation. Therefore, it is crucial to develop ferritic stainless steels with better high-temperature oxidation resistance. This study focuses on improving the high-temperature cyclic oxidation performance of 18Cr-Mo (444-type) ferritic stainless steel by alloying with high-melting-point metal W and the rare earth element Ce. For this purpose, a high-temperature cyclic oxidation experiment was designed to simulate the actual service environment and investigate the high-temperature cyclic oxidation behavior and microstructure evolution of 444-type ferritic stainless steel alloyed with W and Ce. The oxide structure and composition formed during this process were analyzed and characterized using scanning electron microscopy/energy dispersive spectroscopy (SEM-EDS) and electron probe X-ray micro-analyzer (EPMA), in order to reveal the mechanism of action of W and Ce in the cyclic oxidation process. The results show that 18Cr-Mo ferritic stainless steel alloyed with W and Ce exhibits an excellent resistance to high-temperature cyclic oxidation. The element W can promote the precipitation of the Laves phase between the matrix and the oxide film, and the small-sized Laves phase can inhibit the interfacial diffusion of oxidation reaction elements and prevent the inward growth of the oxide film. The element Ce can refine oxide particles and reduce the thickness of the oxide film. CeO2 particles within the oxide film can serve as nucleation sites for the formation of oxide particles from reactive elements, and they also contribute to pinning the oxide film, thereby enhancing its adhesion. [ABSTRACT FROM AUTHOR]

Wire and arc additive manufacturing (WAAM), recognized for its capability to fabricate large-scale, complex parts, stands out due to its significant deposition rates and cost-effectiveness, positioning it as a forward-looking manufacturing method. In this research, we employed two welding currents to produce samples of 316 austenitic stainless steel utilizing the Cold Metal Transfer wire arc additive manufacturing process (CMT-WAAM). This study initially evaluated the maximum allowable arc travel speed (MAWFS) and the formation characteristics of the deposition bead, considering deposition currents that vary between 100 A and175 A in both CMT and CMT pulse(CMT+P) modes. Thereafter, the effect of the CMT+P mode arc on the microstructure evolution was analyzed using the EBSD technique. The findings indicate that the arc travel speed and deposition current significantly affect the deposition bead's dimensions. Specifically, an increase in travel speed or a reduction in current results in reduced bead width and height. Moreover, the employment of the CMT+P arc mode led to a reduction in the average grain size in the mid-section of the sample fabricated by CMT arc and wire additive manufacturing, from 13.426 μm to 9.429 μm. Therefore, the components of 316 stainless steel produced through the CMT+P-WAAM method are considered fit for industrial applications. [ABSTRACT FROM AUTHOR]

The automobile industry relies primarily on spot welding operations, particularly resistance spot welding (RSW). The performance and durability of the resistance spot-welded joints are significantly impacted by the welding quality outputs, such as the shear force, nugget diameter, failure mode, and the hardness of the welded joints. In light of this, the present study sought to determine how the aforementioned welding quality outputs of 0.5 and 1 mm thick austenitic stainless steel AISI 304 were affected by RSW parameters, such as welding current, welding time, pressure, holding time, squeezing time, and pulse welding. In order to guarantee precise evaluation and experimental analysis, it is essential that they are supported by a numerical model using an intelligent model. The primary objective of this research is to develop and enhance an intelligent model employing artificial neural network (ANN) models. This model aims to provide deeper knowledge of how the RSW parameters affect the quality of optimum joint behavior. The proposed neural network (NN) models were executed using different ANN structures with various training and transfer functions based on the feedforward backpropagation approach to find the optimal model. The performance of the ANN models was evaluated in accordance with validation metrics, like the mean squared error (MSE) and correlation coefficient (R2). Assessing the experimental findings revealed the maximum shear force and nugget diameter emerged to be 8.6 kN and 5.4 mm for the case of 1–1 mm, 3.298 kN and 4.1 mm for the case of 0.5–0.5 mm, and 4.031 kN and 4.9 mm for the case of 0.5–1 mm. Based on the results of the Pareto charts generated by the Minitab program, the most important parameter for the 1–1 mm case was the welding current; for the 0.5–0.5 mm case, it was pulse welding; and for the 0.5–1 mm case, it was holding time. When looking at the hardness results, it is clear that the nugget zone is much higher than the heat-affected zone (HZ) and base metal (BM) in all three cases. The ANN models showed that the one-output shear force model gave the best prediction, relating to the highest R and the lowest MSE compared to the one-output nugget diameter model and two-output structure. However, the Levenberg–Marquardt backpropagation (Trainlm) training function with the log sigmoid transfer function recorded the best prediction results of both ANN structures. [ABSTRACT FROM AUTHOR]

Diamond-like carbon (DLC) coatings are effective in protecting the key components of marine equipment and can greatly improve their short-term performance (1.5~4.5 h). However, the lack of investigation into their long-term (more than 200 h) performance cannot meet the service life requirements of marine equipment. Here, three multilayered DLC coatings, namely Ti/DLC, TiCx/DLC, and Ti-TiCx/DLC, were prepared, and their long-term corrosion resistance was investigated. Results showed that the corrosion current density of all DLC coatings was reduced by 1–2 orders of magnitude compared with bare 316L stainless steel (316Lss). Moreover, under long-term (63 days) immersion in a 3.5 wt.% NaCl solution, all DLC coatings could provide excellent long-term corrosion protection for 316Lss, and Ti-TiCx/DLC depicted the best corrosion resistance; the polarization resistances remained at ~3.0 × 107 Ω·cm2 after immersion for 63 days, with more interfaces to hinder the penetration of the corrosive media. Meanwhile, during neutral salt spray (3000 h), the corrosion resistance of Ti/DLC and TiCx/DLC coatings showed a certain degree of improvement because the insoluble corrosion products at the defects blocked the subsequent corrosion. This study can provide a route to designing amorphous carbon protective coatings for long-term marine applications in different environments. [ABSTRACT FROM AUTHOR]

Duplex stainless steels are widely used in many fields due to their excellent corrosion resistance and mechanical properties. However, it is a challenge to achieve duplex microstructure and excellent properties through additive manufacturing. In this work, a 0.09% N 25Cr-type duplex stainless steel was prepared by additive manufacturing (AM) and heat treatment, and its corrosion resistance was investigated. The results show that, compared with S32750 duplex stainless steel prepared by a conventional process, the combination value of film resistance and charge transfer resistance of AM duplex stainless steel was increased by 3.2–5.5 times and the pitting potential was increased by more than 100 mV. The disappearance of residual thermal stress and the reasonable distribution of Cr and N elements in the two phases are the reasons for the improvement of the corrosion resistance of AM duplex stainless steel after heat treatment. In addition, the extremely high purity of AM duplex stainless steel with no visible inclusions resulted in a higher corrosion resistance exhibited at lower pitting-resistance-equivalent number values. [ABSTRACT FROM AUTHOR]

Sub-micro dislocation cellular structures formed during rapid solidification break the strength–ductility trade-off in laser powder bed fusion (LPBF)-processed 316L stainless steel through high-density dislocations and segregated elements or precipitates at the cellular boundaries. The high-density dislocation entangled at the cellular boundary accommodates solidification strains among the cellular structures and cooling stresses through elastoplastic deformation. Columnar grains with cellular structures typically form along the direction of thermal flux. However, the ultra-low misorientations between the adjacent cellular structures and their interactions with the cellular boundary formation remain unclear. In this study, we revealed the ultra-low misorientations between the cellular structures in LPBF-processed 316L stainless steel using conventional electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), and transmission electron microscopy (TEM). The conventional EBSD and TKD analysis results could provide misorientation angles smaller than 2°, while the resolution mainly depends on the specimen quality and scanning step size, and so on. A TEM technique with higher spatial resolution provides accurate information between adjacent dislocation cells with misorientation angles smaller than 1°. This study presents evidence that the TEM method is the better and more precise analytical method for the misorientation measurement of the cellular structures and provides insights into measuring the small misorientation angles between adjacent dislocation cells and nanograins in nanostructured metals and alloys with ultrafine-grained microstructures. [ABSTRACT FROM AUTHOR]

This research examines the behavior of electrochemical passivation and the chemistry of surface films on 654SMO super austenitic stainless steel and C276 nickel-based alloy in simulated condensates from flue gas desulfurization in power plant chimneys. The findings indicate that the resistance to polarization of the protective film on both materials initially rises and then falls with either time spent in the solution or the potential of anodic polarization. Comparatively, 654SMO exhibits greater polarization resistance than C276, indicating its potential suitability as a chimney lining material. Mott–Schottky analysis demonstrates that the density of donors in the passive film formed on 654SMO exceeds that on C276, potentially due to the abundance of Fe oxide in the passive film, which exhibits the characteristics of an n-type semiconductor. The primary components of the passive films on both materials are Fe oxides and Cr oxides. The formation of a thin passive film on C276 in the simulated condensates is a result of the low Gibbs free energy of nickel oxide and low Cr content. The slower diffusion coefficient of point defects leads to the development of a thicker and more compact passive film on the surface of 654SMO. [ABSTRACT FROM AUTHOR]

The prerequisite of the weld bead finishing is intricately linked to the quality of the welded joint. It constitutes the final, yet pivotal, stage in its formation, significantly influencing the reliability of structural components and machines. This article delineates an innovative post-weld surface finishing method, distinguished by the movement of a specialized cutting tool along a butt weld. This method stands out due to its singular approach to machining allowance, wherein the weld bead height is considered and eradicated in a single pass of the cutting tool. Test samples were made of AISI 304L, AISI 316L stainless steels and EN AW-5058 H321, EN AW-7075 T651 aluminum alloys butt-welded with TIG methods. Following the welding process, the weld bead was finished in accordance with the innovative method to flush the bead and the base metal's surface. For the quality control of welded joints before and after the weld finishing, two non-destructive testing methods were chosen: Penetrant Testing (PT) and Radiographic Testing (RT). This article provides results from the examination of 2D profile parameters and 3D stereometric characteristics of surface roughness using the optical method. Additionally, metallographic results are presented to assess changes in the microstructure, the microhardness, and the degree of hardening within the surface layer induced by the application of the innovative post-weld finishing method. [ABSTRACT FROM AUTHOR]

Nanoindentation measurements were conducted to investigate the high-cycle response of 316L stainless steel in bending fatigue. Hardness variation owing to the gradient flexure stress amplitude for different curvatures was plotted along with the thickness and length, respectively. Scanning electron microscopy (SEM) was subsequently conducted to explore the deformation characteristics in multiple layers, which had cyclic gradient stress, on the cross-section of specimens. The nanoindentation results indicated that the cyclic hardening response of 316L stainless steel is correlated with the level of stress amplitude in the high-cycle fatigue (HCF) regime. Furthermore, an analytical model was proposed to clarify the relationship between nanohardness and stress amplitude. Finally, the evolution of damage accumulation due to irreversible plastic deformation is continuous during stress reduction up to the neighboring zone at the neutral surface of the flexure beam in some individual grains. [ABSTRACT FROM AUTHOR]