Search

This study reports the production of mid-infrared (MIR) porous anodic alumina (PAA)-based microcavities with tunable optical quality. The spectral position of the cavity resonance peak (λC), along with its intensity (IR) and Q-factor, varies depending on the geometric positioning of the cavity layer within the multilayer stack of alternating low- and high-porosity layers, as well as the type of cavity produced—either by high voltage (CvH-type) or low voltage (CvL-type) pulses. In most cases, PAA microcavities with CvH-type cavity layers exhibited superior light confinement properties compared to those with CvL-type cavities. Additionally, shifting the cavity layer from the center toward the edges of the multilayer stack enhanced the intensity of the resonance peak. For PAA microcavities with CvH-type cavity layers, the highest intensity (IR = 53%) and the largest Q-factor (Q = 31) were recorded at λC of around 5.1 µm. The anodization approach used in this study demonstrates significant potential for designing PAA-based microcavities with high optical performance in the MIR spectral region, especially with further refinement of electrochemical parameters. These findings pave the way for the development of new photonic materials specifically tailored for the MIR spectral range, broadening their applications in various optoelectronic and sensing technologies. [ABSTRACT FROM AUTHOR]

Etidronic acid, used in aluminum anodization, has a great potential for the fabrication of porous anodic alumina (PAA) with large cell sizes (>540 nm). PAAs are particularly suited to applications in optics and photonics where large-scale periodicity corresponding to visible or infrared light is needed. Additionally, such PAAs should be characterized by long-range pore ordering. However, to obtain regular pore arrangement in an etidronic electrolyte, the anodization should be performed at high electric fields using relatively high temperatures, which makes the process challenging in terms of its stability. To stabilize the process, the electrolyte can be modified with ethanol. In this work, the impact of ethanol on pore geometry and a level of pore ordering is systematically analyzed. It is shown that the additive tends to reduce pore ordering. Moreover, by changing the anodizing temperature and the amount of ethanol, it is possible to tune the porosity of the PAA template. At 20 °C, porosity drops from 14% in PAA grown in a pure water-based electrolyte to ca. 8% in PAA fabricated in the 1:3 v/v EtOH:H2O electrolyte. The larger PAA thickness obtained for the same charge density strongly suggests that PAA formation efficiency increases in the 1:3 v/v EtOH:H2O mixture. [ABSTRACT FROM AUTHOR]

In this work, the influence of various electrochemical parameters on the production of porous anodic alumina (PAA)-based DBRs (distributed Bragg reflector) during high-temperature-pulse-anodization was studied. It was observed that lowering the temperature from 30 to 27 °C brings about radical changes in the optical performance of the DBRs. The multilayered PAA fabricated at 27 °C did not show optical characteristics typical for DBR. The DBR performance was further tuned at 30 °C. The current recovery (iamax) after application of subsequent UH pulses started to stabilize upon decreasing high (UH) and low (UL) voltage pulses, which was reflected in a smaller difference between initial and final thickness of alternating dH and dL segments (formed under UH and UL, respectively) and a better DBR performance. Shortening UH pulse duration resulted in a progressive shift of photonic stopbands (PSBs) towards the blue part of the spectrum while keeping intensive and symmetric PSBs in the NIR-MIR range. Despite the obvious improvement of the DBR performance by modulation of electrochemical parameters, the problem regarding full control over the homogeneous formation of dH+dL pairs remains. Solving this problem will certainly lead to the production of affordable and efficient PAA-based photonic crystals with tunable photonic properties in the NIR-MIR region. [ABSTRACT FROM AUTHOR]

In this work, the influence of a wide range anodizing temperature (5–30 °C) on the growth and optical properties of PAA-based distributed Bragg reflector (DBR) was studied. It was demonstrated that above 10 °C both structural and photonic properties of the DBRs strongly deteriorates: the photonic stop bands (PSBs) decay, broaden, and split, which is accompanied by the red shift of the PSBs. However, at 30 °C, new bands in transmission spectra appear including one strong and symmetric peak in the mid-infrared (MIR) spectral region. The PSB in the MIR region is further improved by a small modification of the pulse sequence which smoothen and sharpen the interfaces between consecutive low and high refractive index layers. This is a first report on PAA-based DBR with a good quality PSB in MIR. Moreover, it was shown that in designing good quality DBRs a steady current recovery after subsequent application of high potential (UH) pulses is more important than large contrast between low and high potential pulses (UH-UL contrast). Smaller UH-UL contrast helps to better control the current evolution during pulse anodization. Furthermore, the lower PSB intensity owing to the smaller UH-UL contrast can be partially compensated by the higher anodizing temperature. [ABSTRACT FROM AUTHOR]