Search

Filler content in dental composites is credited for affecting its physical and mechanical properties. This study evaluated the correlation between the filler percentage and strength, modulus, shrinkage stress, depth of cure, translucency and radiopacity of commercially available high- and low-viscosity dental composites. Filler weight percentage (wt%) was determined through the burned ash technique (800 °C for 15 min). Three-point bend flexural strength and modulus were measured according to ISO 4049 with 2 mm × 2 mm × 25 mm bars. Shrinkage stress was evaluated using a universal testing machine in which composite was polymerized through two transparent acrylic rods 2 mm apart. Shrinkage was measured from the maximum force following 500 s. The translucency parameter (TP) was measured as the difference in color (ΔE00) of 1 mm thick specimens against white and black tiles. The depth of cure was measured according to ISO 4049 in a cylindrical metal mold (4 mm diameter) with a 10 s cure. Radiopacity was measured by taking a digital X-ray (70 kVp for 0.32 s at 400 mm distance) of 1 mm thick specimens and comparing the radiopacity to an aluminum step wedge using image analysis software. The correlation between the filler wt% and properties was measured by Pearson's correlation coefficient using SPSS. There was a positive linear correlation between the filler wt% and modulus (r = 0.78, p < 0.01), flexural strength (r = 0.46, p < 0.01) and radiopacity (r = 0.36, p < 0.01) and negative correlation with translucency (r = −0.29, p < 0.01). Filler wt% best predicts the modulus and strength and, to a lesser extent, the radiopacity and translucency. All but two of the high- and low-viscosity composites from the same manufacturer had statistically equivalent strengths as each other; however, the high-viscosity materials almost always had a statistically higher modulus. For two of the flowable composites measured from the same manufacturer (3M and Dentsply), there was a lower shrinkage stress in the bulk-fill version of the material but not for the other two manufacturers (Ivoclar and Tokuyama). All flowable bulk-fill composites achieved a deeper depth of cure than the flowable composite from the same manufacturer other than Omnichroma Flow Bulk. [ABSTRACT FROM AUTHOR]

Hydraulic asphalt concrete is known for its excellent seepage control performance and strong deformation resistance. This engineering material has widespread applications in the seepage control structures of hydraulic buildings. Recent projects have investigated the use of acidic aggregates to improve economic efficiency. However, they have also highlighted the weaker adhesion between acidic aggregates and asphalt, which necessitates stringent construction process control. This study investigates the impact of resting conditions on the tensile properties of acidic aggregate hydraulic asphalt concrete. The results of the tensile testing indicate that the storage time significantly affects the performance of asphalt concrete. The tensile strength of the specimens without anti-stripping agents decreased from 1.711 MPa to 0.914 MPa after resting periods of 0, 10, 20, and 30 days. The specimens treated with anti-stripping agents also showed a decrease in tensile strength over time, similar to the trend observed in the previous specimens. Digital specimen simulations indicated a decrease in cohesion between the asphalt and the aggregate from 5.375 MPa to 2.664 MPa after 30 days, representing a reduction of 50.44%. To counteract the effect of the storage time on the bonding between acidic aggregates and asphalt, this study recommends reducing the grading index and maximum size of aggregates, decreasing the coarse aggregate content, and selecting smooth aggregate shapes. [ABSTRACT FROM AUTHOR]

To promote resourceful utilization of argon oxygen decarburization (AOD) slag, this research developed a new three-ash stabilized recycled aggregate with AOD slag, cement, fly ash (FA), and recycled aggregate (RA) as raw materials. The AOD slag was adopted as an equal mass replacement for fly ash. The application of this aggregate in a road base layer was investigated in terms of its mechanical properties and mechanistic analysis. First, based on a cement: FA ratio of 1:4, 20 sets of mixed proportion schemes were designed for four kinds of cement dosage and AOD slag replacement rates (R/%). Through compaction tests and the 7-day unconfined compressive strength test, it was found that a 3% cement dosage met the engineering requirements. Then, the unconfined compressive strength test, indirect tensile strength test, compressive rebound modulus test, and expansion rate test were carried out at different age thresholds. The results showed that the mixture's strength, modulus, and expansion rate increased initially and then stabilized with age, while the strength and modulus initially increased and then decreased with increasing R. Secondly, based on X-ray diffraction (XRD) and scanning electron microscopy (SEM) used to analyze the mechanism, it was found that the strength, modulus, and expansion rate of the new material can be promoted by blending AOD slag, due to its ability to fully stimulate the hydration reaction and pozzolanic reaction of the binder. Finally, based on the strength and modulus results, R = 3% was identified as the optimal ratio, which provides a reference point for the effective application of AOD slag and RA in road base materials. [ABSTRACT FROM AUTHOR]

Generally, the dynamic modulus and bending stiffness modulus are used to evaluate the mechanical properties of asphalt mixture, and they are also used as basic parameters for asphalt mixture design. Therefore, a study was conducted on changes in the dynamic modulus and bending stiffness modulus of hot-recycled asphalt mixture with high levels of reclaimed asphalt pavement (RAP) under the influence of different factors: dosage of regenerant, curing temperature, and curing time. The performance of reclaimed asphalt pavement (RAP) was first evaluated. Then, the hot-recycled asphalt mixture was adjusted and designed in order to conduct modulus experiments, composed of the dynamic modulus test and three-point bending test. Finally, the influencing factors were not only qualitatively but also quantitatively analyzed to clarify the change laws of the mechanical parameters of hot-recycled asphalt mixture. The results showed that the modulus of the recycled asphalt mixture first decreased, then increased, and then decreased with increasing dosage of regenerant. As the curing time or temperature increased, the modulus first decreased and then increased. In terms of the dynamic modulus of the hot-recycled asphalt mixture, the curing time had the greatest impact, followed by dosage of the regenerant and curing temperature. For bending stiffness modulus, the influence of dosage of the regenerant was the greatest, followed by curing time and curing temperature. For the bending stiffness modulus of hot-recycled asphalt mixture, the curing conditions had a greater influence compared with the dynamic modulus. [ABSTRACT FROM AUTHOR]

The current work is focused on numerical and experimental studies of woven fabric composites modified by hybridisation with biological (cellulosic) filler materials. The mechanical performance of the composites is characterized under tensile, bending and impact loads and the effect of hybridisation is observed with respect to pure and nonhybrid composites. Numerical models are developed using computational tools to predict mechanical performance under tensile loading. The computational prediction results are compared and validated with relevant experimental results. This research is aimed at understanding the mechanical performance of basalt–epoxy composites partially reinforced with micro-/nano-sized bio-fillers from cellulose and intended for various application areas. Different weave structures, e.g., plain, twill, matt, etc., were investigated with respect to the mechanical properties of the hybrid composites. The effects of hybridizing with cellulose particles and different weave patterns of the basalt fabric are studied. In general, the use of high-strength fibres such as basalt along with cellulosic fillers representing up to 3% of the total weight improves the mechanical performance of the hybrid structures. The thermomechanical performance of the hybrid composites improved significantly by using basalt fabric as well as by addition of 3% weight of cellulosic fillers. Results reveal the advantages of hybridisation and the inclusion of natural cellulosic fillers in the hybrid composite structures. The material developed is suitable for high-end applications in components for construction that demand advanced mechanical and thermomechanical performance. Furthermore, the inclusion of biodegradable fillers fulfills the objectives of sustainable and ecological construction materials. [ABSTRACT FROM AUTHOR]

Magnetic nanoparticles of NiFe2O4 were successfully prepared by utilizing the sol–gel techniques. The prepared samples were investigated through various techniques such as X-ray diffraction (XRD), transmission electron microscopy (TEM), dielectric spectroscopy, DC magnetization and electrochemical measurements. XRD data analysed using Rietveld refinement procedure inferred that NiFe2O4 nanoparticles displayed a single-phase nature with face-centred cubic crystallinity with space group Fd-3m. Average crystallite size estimated using the XRD patterns was observed to be ~10 nm. The ring pattern observed in the selected area electron diffraction pattern (SAED) also confirmed the single-phase formation in NiFe2O4 nanoparticles. TEM micrographs confirmed the uniformly distributed nanoparticles with spherical shape and an average particle size of 9.7 nm. Raman spectroscopy showed characteristic bands corresponding to NiFe2O4 with a shift of the A1g mode, which may be due to possible development of oxygen vacancies. Dielectric constant, measured at different temperatures, increased with temperature and decreased with increase in frequency at all temperatures. The Havrilliak–Negami model used to study the dielectric spectroscopy indicated that a NiFe2O4 nanoparticles display non-Debye type relaxation. Jonscher's power law was utilized for the calculation of the exponent and DC conductivity. The exponent values clearly demonstrated the non-ohmic behaviour of NiFe2O4 nanoparticles. The dielectric constant of the nanoparticles was found to be >300, showing a normal dispersive behaviour. AC conductivity showed an increase with the rise in temperature with the highest value of 3.4 × 10−9 S/cm at 323 K. The M-H curves revealed the ferromagnetic behaviour of a NiFe2O4 nanoparticle. The ZFC and FC studies suggested a blocking temperature of ~64 K. The saturation of magnetization determined using the law of approach to saturation was ~61.4 emu/g at 10 K, corresponding to the magnetic anisotropy ~2.9 × 104 erg/cm3. Electrochemical studies showed that a specific capacitance of ~600 F g−1 was observed from the cyclic voltammetry and galvanostatic charge–discharge, which suggested its utilization as a potential electrode for supercapacitor applications. [ABSTRACT FROM AUTHOR]

Structural coloring of dental resin-based composites (RBC) is used to create universal chromatic materials designed to meet any aesthetic need, replacing the mixing and matching of multiple shades. The microstructural adjustments to create this desideratum involve nanoscale organic–inorganic core–shell structures with a particular arrangement. The generally higher polymer content associated with these structures compared to universal chromatic RBCs colored by pigments, which in their microstructure come close to regularly shaded RBCs, can influence the way the material ages. Accelerated and slow aging up to 1.2 years of immersion in artificial saliva at 37 °C were therefore compared in relation to their effects on the materials described above and in relation to the immersion conditions prescribed by standards. Quasi-static and viscoelastic parameters were assessed to quantify these effects by a depth-sensing indentation test equipped with a DMA module. The microstructure of the materials was characterized by scanning electron microscopy. The results convincingly show a differentiated influence of the aging protocol on the measured properties, which was more sensitively reflected in the viscoelastic behavior. Accelerated aging, previously associated with the clinical behavior of RBCs, shows a 2- to 10-fold greater effect compared to slow aging in artificial saliva of up to 1.2 years, highly dependent on the microstructure of the material. [ABSTRACT FROM AUTHOR]

In this work, Gd2O3 bulks were sintered at temperatures ranging from 1400 °C to 1600 °C for times from 6 h to 24 h, and their microstructure and properties were studied for a wider application of materials in thermal barrier coatings. The densification of the Gd2O3 bulk reached 96.16% when it was sintered at 1600 °C for 24 h. The elastic modulus, hardness, fracture toughness and thermal conductivity of the bulks all increased with the rise in sintering temperature and extension of sintering time, while the coefficient of thermal expansion decreased. When the Gd2O3 bulk was sintered at 1600 °C for 24 h, it had the greatest elastic modulus, hardness, fracture toughness and thermal conductivity of 201.15 GPa, 9.13 GPa, 15.03 MPa·m0.5 and 2.75 W/(m·k) (at 1100 °C), respectively, as well as the smallest thermal expansion coefficients of 6.69 × 10−6/°C (at 1100 °C). [ABSTRACT FROM AUTHOR]

The melt-quenching technique was used to synthesize tellurite glasses of the chemical composition 80TeO2-(20-x) ZnO-xV2O5. X-ray diffraction (XRD) patterns indicate the amorphous nature of the prepared glasses. Raman and FTIR measurements demonstrate a progressive substitution of the Te-O-Te linkages by the Te-O-V bridges and the formation of VO4 and VO5 units by a change of the vanadium coordination due to the higher number of oxygens incorporated by further addition of V2O5. The AC conductivity was investigated in the frequency range of 40 Hz to 107 Hz between 473 K to 573 K. A good coherence of the AC conductivity was found using a model correlating the barrier hopping (CPH) and the dominant conduction process changes from ionic to polaronic with the addition of V2O5. The dielectric constant exhibits high values in the range of lower and medium frequencies. Both variations of the electric modulus and the dielectric loss parameters with frequency and temperature showed a relaxation character mainly assigned to the vanadate phases. The electric modulus displays a non-Debye dielectric dispersion and a relaxation process. The present results open the door to future zinc-tellurite glasses-doped vanadium exploitation as a potential electrolyte-based material for solid-state batteries. [ABSTRACT FROM AUTHOR]

To date, there have been a limited number of studies modeling the tensile modulus in the polymer halloysite nanotube (HNT) systems before or after percolation onset. In this paper, an equation for a composite's modulus post-percolation onset was developed for HNT-filled samples including the interphase and HNT network. The dispersed nanoparticles and adjoining interphase part were neglected, because they caused ineffective influences on the stiffness of the system after percolation onset. The developed model reflects the impacts of HNTs' size, interphase depth, percolation onset and the volume shares and moduli of the HNT network and its adjacent interphase on the modulus of HNT-based systems. The impacts of issues on the nanocomposite modulus are defendable, confirming the effectiveness of the developed model. HNT length, interphase depth, HNT concentration, net modulus and net portion directly influenced the stiffness, while the HNT radius and percolation onset had inverse effects. Results show that there was a 142% improvement in the modulus of samples at an interphase depth of 40 nm. Moreover, the stiffness improved by 60% at a net modulus of 200 GPa, but it later exhibited a 180% enhancement at a net modulus of 1000 GPa. In addition, the experimental data for the modulus of numerous composites display fine agreement to the predictions, confirming the validity of the developed model. [ABSTRACT FROM AUTHOR]

The objective was to evaluate new commercially available ion-releasing restorative materials and compare them to established anti-cariogenic materials. Four materials were tested: alkasite Cention (Ivoclar Vivadent) in self-cure or light-cure mode, giomer Beautifil II (Shofu), conventional glass-ionomer Fuji IX (GC), and resin composite Tetric EvoCeram (Ivoclar Vivadent) as a control. Flexural strength, flexural modulus, and Weibull modulus were measured one day, three months, and after three months with accelerated aging in ethanol. Water sorption and solubility were evaluated for up to one year. Degree of conversion was measured during 120 min for self-cured and light-cured Cention. In this study, Beautifil II was the ion-releasing material with the highest flexural strength and modulus and with the best resistance to aging. Alkasite Cention showed superior mechanical properties to Fuji IX. Weibull analysis showed that the glass-ionomer had the least reliable distribution of mechanical properties with the highest water sorption. The solubility of self-cured alkasite exceeded the permissible values according to ISO 4049. Degree of conversion of light-cured Cention was higher than in self-cure mode. The use of alkasite Cention is recommended only in the light-cure mode. [ABSTRACT FROM AUTHOR]

Nanoindentation is widely used to investigate the surface-mechanical properties of biocomposites. In this study, polypropylene random copolymer (PPRC) and biowaste rice husk (BRH) were used as the main raw materials, and glass-fiber-reinforced polypropylene and talc were also used with BRH to enhance the mechanical characterization of the biocomposites. The interfacial bonding between the polymer and the rice husk was increased by treating them with maleic anhydride and NaOH, respectively. The results obtained from the nanoindentation indicated that the plastic behavior of the biocomposites was prominent when untreated BRH was used and vice versa. The modulus and hardness of the biocomposite improved by 44.8% and 54.8% due to the neat PPRC, respectively. The tribological properties were studied based on the hardness-to-modulus ratio and it was found that BRH- and talc-based biocomposites were better than other samples in terms of low friction and wear rate. The creep measurements showed that untreated rice husk biocomposite exhibited high resistance to load deformation. [ABSTRACT FROM AUTHOR]

Gd and Yb elements have high chemical stability, which can stabilize the solid solution in ZrO2. Gd2O3 and Yb2O3 have high melting points, and good oxidation resistance in extreme environments, stable chemical properties. Therefore, Gd2O3 and Yb2O3 were added to ZrO2 to stabilize oxides, improve the high temperature stability, and effectively decrease the thermal conductivity at high temperature. In this work, 5 wt% Yb2O3 and 5 wt%, 10 wt%, 15 wt% Gd2O3 were doped into 8 wt% Y2O3 stabilized ZrO2 (8YSZ) powders as thermal barrier coating materials, and sintered at 1650 °C for 6 h, 12 h, 24 h. The effects of Gd2O3 addition on the microstructure, density, thermal conductivity, hardness, and fracture toughness of Gd2O3-Yb2O3-Y2O3-ZrO2 (GYYZO) bulk composite ceramics were investigated. It was found that the densification of the 8YSZ bulk and GYYZO bulk with 15 wt% Gd2O3 reached 96.89% and 96.22% sintered at 1650 °C for 24 h. With the increase of Gd2O3 addition, the hardness, elastic modulus and fracture toughness of the GYYZO bulk increased and the thermal conductivity and thermal expansion coefficient of the GYYZO bulk decreased. GYYZO bulk with 15 wt% Gd2O3 sintered at 1650 °C for 24h had the highest hardness, elastic modulus and fracture toughness of 15.61 GPa, 306.88 GPa, 7.822 MPa·m0.5, and the lowest thermal conductivity and thermal expansion coefficient of 1.04 W/(m·k) and 7.89 × 10−6/°C at 1100 °C, respectively. The addition of Gd2O3 into YSZ could not only effectively reduce the thermal conductivity but also improve the mechanical properties, which would improve the thermal barrier coatings' performances further. [ABSTRACT FROM AUTHOR]

In materials science and engineering, a significant amount of research has been carried out using indentation techniques in order to characterize the mechanical properties and microstructure of a broad range of natural and engineered materials. However, there are many unresearched or partly researched areas, such as, for example, the investigation of the shape of the indentation load–displacement curve, the associated mechanism in porous materials with clastic texture, and the influence of the texture on the constitutive behavior of the materials. In the present study, nanoindentation is employed in the analysis of the mechanical behavior of a benchmark material composed of plaster of Paris, which represents a brand of highly porous-clastic materials with a complex structure; such materials may find many applications in medicine, production industry, and energy sectors. The focus of the study is directed at the examination of the influence of the porous structure on the load–displacement response in loading and unloading phases based on nanoindentation experiments, as well as the variation with repeating the indentation in already indented locations. Events such as pop-in in the loading phase and bowing out and elbowing in the unloading phase of a given nanoindentation test are studied. Modulus, hardness, and the elastic stiffness values were additionally examined. The repeated indentation tests provided validations of various mechanisms in the loading and unloading phases of the indentation tests. The results from this study provide some fundamental insights into the interpretation of the nanoindentation behavior and the viscoelastic nature of porous-clastic materials. Some insights on the influence of indentation spacing to depth ratio were also obtained, providing scope for further studies. [ABSTRACT FROM AUTHOR]

The longevity of indirect restorations is primarily determined by the appropriate selection of the luting material. The function of a luting material is to seal the restoration and hold it in place for the time required for service. The mechanical behavior of luting materials and in particular their aging behavior, therefore, play a decisive role. The study provides a comparative analysis of the static and dynamic mechanical behavior of the most commonly used luting material categories—zinc phosphate cement, glass–ionomer cement, resin-modified glass–ionomer cement, resin-based composites, and self-adhesive resin-based composites—and their aging behavior. It also takes into account that luting materials are viscoelastic materials, i.e., materials that respond to external loading in a way that lies between an elastic solid and a viscous liquid. Flexural strength and modulus were determined in a three-point bending test followed by fractography analysis. The quasi-static and viscoelastic behavior was analyzed by a depth-sensing indentation test provided with a dynamic mechanical analysis (DMA) module at 20 different frequencies (1–50 Hz). The fracture toughness was evaluated in a notchless triangular prism (NTP) test. Material type exhibits the strongest influence on all measured properties, while the effect of aging becomes more evident in the material reliability. The variation of the viscoelastic parameters with aging reflects cement maturation or polymer plasticization. [ABSTRACT FROM AUTHOR]

In this work, the effects of chemical pretreatment and different fiber loadings on mechanical properties of the composites at the sub-micron scale were studied through nanoindentation. The composites were prepared by incorporating choline chloride (ChCl) pretreated rice husk waste (RHW) in low-density polyethylene (LDPE) using melt processing, followed by a thermal press technique. Nanoindentation experiments with quasi continuous stiffness mode (QCSM) were performed on the surface of produced composites with varying content of pretreated RHW (i.e., 10, 15, and 20 wt.%). Elastic modulus, hardness, and creep properties of fabricated composites were measured as a function of contact depth. The results confirmed the appreciable changes in hardness, elastic modulus, and creep rate of the composites. Compliance curves indicated that the composite having 20 wt.% of pretreated RHW loading was harder compared to that of the pure LDPE and other composite samples. The values of elastic modulus and hardness of the composite containing 20 wt.% pretreated RHW were increased by 4.1% and 24% as compared to that of the pure LDPE, respectively. The creep rate of 42.65 nm/s and change in depth of 650.42 nm were also noted for the composite with RHW loading of 20 wt.%, which showed the substantial effect of holding time at an applied peak load of 100 mN. We believe that the developed composite could be a promising biodegradable packaging material due to its good tribo-mechanical performance. [ABSTRACT FROM AUTHOR]

In this study, the influence of alloying elements on the mechanical properties of iron borides FeB and Fe2B formed in Fe-B-X (X = C, Cr, Mn, V, W, Mn + V) alloys were evaluated using instrumented indentation measurement. The microstructural characterization of the alloys was performed by means of X-ray diffraction and scanning electron microscope equipped with an energy dispersive X-ray analyzer. The fraction of the phases present in the alloys was determined either by the lever rule or by image analysis. The hardest and stiffest FeB formed in Fe-B-X (X = C, Cr, Mn) alloys was observed in the Fe-B-Cr alloys, where indentation hardness of HIT = 26.9 ± 1.4 GPa and indentation modulus of EIT = 486 ± 22 GPa were determined. The highest hardness of Fe2B was determined in the presence of tungsten as an alloying element, HIT = 20.8 ± 0.9 GPa. The lowest indentation hardness is measured in manganese alloyed FeB and Fe2B. In both FeB and Fe2B, an indentation size effect was observed, showing a decrease of hardness with increasing indentation depth. [ABSTRACT FROM AUTHOR]

The physico-chemical properties of the Uranium intermetallic compound are of technological importance for improvement of the safety and compatibility of nuclear engineering systems. Diffusion couple samples with U and Cu were assembled and U-Cu intermetallic compounds were fabricated at interface by hot pressure diffusion method at a treatment temperature of 350 °C to 650 °C and at a pressure of 168 MPa in a vacuum furnace. The microstructure and element distribution of the compound phase have been studied by means of SEM, EDS, and XRD. The result showed that a new phase was developed to a thickness of approximately 10 μm with a ration of U:Cu with 1:5. Mechanical properties such as elastic moduli and hardness of the compound have been studied by means of nanoindentation. The nanoindentation testing on sample indicated that hardness of Uranium intermetallic compound are higher than that of metal U and Cu. Uranium intermetallic compound and U have a Young's moduli with 121 GPa, 160 GPa respectively. The elastic/plastic responses of U-Cu intermetallic compound and U under nanoindentation tests were also discussed in detail. [ABSTRACT FROM AUTHOR]