Search

Tetracycline (TC) and arsenic contaminants are two main pollutants in aquaculture and livestock husbandry, and they have drawn worldwide attention. To address this issue, a novel N-doped carbon@magnesium silicate (CMS) was fabricated via a facile and low-cost hydrothermal route, adopting glucose and ammonia as C and N sources, respectively. The synergetic combination of carbon and magnesium silicate makes CMS possess a high surface area of 201 m2/g and abundant functional groups. Due to the abundant C- and N-containing functional groups and Mg-containing adsorptive sites, the maximum adsorption capacity values of CMS towards As(V) and TC are 498.75 mg/g and 1228.5 mg/g, respectively. The type of adsorption of As(V) and TC onto CMS is monolayer adsorption. An adsorption kinetic study revealed that the mass transfer and intraparticle process dominates the sorption rate of As(V) and TC adsorption onto CMS, respectively. Various functional groups synthetically participate in the adsorption process through complexion, π–π EDA interactions, and hydrogen bonds. This work provides a one-step, low-cost route to fabricate a N-doped carbonaceous adsorbent with a high surface area and abundant functional groups, which has great potential in the application of practical sewage treatment. [ABSTRACT FROM AUTHOR]

Glass-fiber reinforced polymer (GFRP) bars are increasingly widely used in slope support instead of steel bars or steel pipes. GFRP Bars are generally connected with the slope by combining conical nut and tray, but the tray stress still lacks corresponding theoretical calculation and strength verification methods. Therefore, assuming that the tray is an equal thickness thin plate, the internal force distribution of the tray is calculated using the thin plate bending and cavity expansion theory, and compared with the finite element numerical analysis results of the tray. The calculation and analysis show that the elastic theoretical solution of internal force distribution of equal thickness tray is basically the same as the numerical simulation solution of variable thickness tray. The tray loading and free surface are controlled by hoop tensile and radial compressive stress, respectively. The inner wall of the free surface of the tray is the weakest part of the tray, and the ultimate strength of a GFRP tray is 35.81–53.00% of the standard tensile strength of Φ20 GFRP bars by distortion energy density. This theoretical method can be used for stress analysis of variable thickness trays and has played technical support for promoting the application of GFRP bars in slope support. [ABSTRACT FROM AUTHOR]

Two single track multi-layer walls with linear energy inputs (LEIs) of 219 and 590 J/mm were deposited by cold metal transfer-based wire arc additive manufacturing system. Combined with the X-ray diffraction technique, scanning electron microscope and uniaxial tensile tests, the influences of LEI and cooling rate (CR) on the microstructure evolution, mechanical properties and fracture mechanisms of the studied steel are analyzed. It is observed that the microstructures of the studied steel are mainly composed of δ-ferrite and austenite dendrites. σ phase is formed on the δferrite–austenite interface under low CR. Meanwhile, the primary dendrites' spacing decreases with the decrease in LEI or the increase in CR, and the maximal primary dendrites' spacing is 32 μm. The values of elongation to fracture roughly decline with the decrease in LEI or the increase in CR, but the variations of ultimate tensile strength and yield stress show an opposite trend. In addition, the mesoscopic damages in the studied steel under low LEI are mainly caused by the coalescence of pores. While under high LEI, the cracks are induced by the dislocations piling up around δ-ferrite. [ABSTRACT FROM AUTHOR]

In this study, we report a novel high-throughput and instant-mixing droplet microfluidic system that can prepare uniformly mixed monodisperse droplets at a flow rate of mL/min designed for rapid mixing between multiple solutions and the preparation of micro-/nanoparticles. The system is composed of a magneton micromixer and a T-junction microfluidic device. The magneton micromixer rapidly mixes multiple solutions uniformly through the rotation of the magneton, and the mixed solution is sheared into monodisperse droplets by the silicone oil in the T-junction microfluidic device. The optimal conditions of the preparation of monodisperse droplets for the system have been found and factors affecting droplet size are analyzed for correlation; for example, the structure of the T-junction microfluidic device, the rotation speed of the magneton, etc. At the same time, through the uniformity of the color of the mixed solution, the mixing performance of the system is quantitatively evaluated. Compared with mainstream micromixers on the market, the system has the best mixing performance. Finally, we used the system to simulate the internal gelation broth preparation of zirconium broth and uranium broth. The results show that the system is expected to realize the preparation of ceramic microspheres at room temperature without cooling by the internal gelation process. [ABSTRACT FROM AUTHOR]

The relationships between initial microstructures, process parameters, and grain evolutions in isothermal holdings have drawn wide attention in recent years, but the grain growth behaviors of 300M steel were not well understood, resulting in a failure in precise microstructure controlling in heat treatment. In this work, in situ observations were carried out to characterize the grain evolutions of 300M steel with varying holding time, holding temperatures, and initial microstructures. The intriguing finding was that the grain refinement by austenization of 300M steel was followed by a dramatic grain growth in the initial stage of holding (≤~600 s), and with increasing time (~600–7200 s), the average grain size appeared to have a limit value at specific temperatures. The austenization process accelerated the grain growth by generating large quantity of grain boundaries at the initial stage of holdings, and the growth rate gradually slowed down after holding for ~600 s because the driven force was weakened due to the reduction of grain boundary energy. The initial structure and the initial grain size of 300M steel had no obvious influences on the grain size evolutions. The mechanisms of grain growth were analyzed based on in situ observations and transmission electron microscope (TEM) characterizations. A grain evolution model considering the grain boundary migration of 300M steel was established for the isothermal holding process. Good agreement was obtained between the in situ observation results and the model calculation results. This investigation aimed to understand fundamentally the grain evolutions of 300M steel in the isothermal holding process. [ABSTRACT FROM AUTHOR]

The formability of aluminum alloy sheet in electromagnetic impaction deformation has attracted the attention of numerous researchers for the past decades. However, the influences of die geometry and high-speed impaction electromagnetic deformation on formability have not been well established, thereby resulting in the formability of the sheet not being developed fully. In this study, the influence of die geometry on the formability of 5052 aluminum alloy in electromagnetic deformation was investigated by comparing the formability of 5052 aluminum alloys formed using a hemispherical die and a cylindrical die. The intriguing finding is that the formability of the 5052 aluminum alloy formed using a cylindrical die is considerably higher than that formed using a hemispherical die. Therefore, die geometry significantly influences the formability of 5052 aluminum alloy. The influence of die geometry on the formability of 5052 aluminum alloy in high-speed impaction electromagnetic deformation was explained in terms of strain rate, pressure stress, and stress state. This investigation enhances insight into the interaction between sheets and dies, and provides a reference for the studying influence of dies on the forming limit of sheets in high-speed impaction deformation. [ABSTRACT FROM AUTHOR]

In the process of electromagnetic forming (EMF), the rebound effect caused by high speed collision between sheet and die will affect the fittability, which results in a bad forming quality of workpiece. In this paper, finite element models of direct EMF and indirect EMF with an elastic medium are established, the influence factors of fittability in indirect EMF are studied, the two forming processes are compared, and the mechanisms of reduced rebound effect in indirect EMF are revealed. The results show that: in indirect EMF, with the increase of the discharging voltage or thickness of rubber, the fittability increases and then decreases; when the thickness of driver plate is equal to the skin depth of the driver plate, the fittability is the best. The optimal process parameters of indirect EMF are as follows: the discharging voltage is 10 kV, the thickness of the rubber is 20 mm and the thickness of driver plate is 2 mm. The rebound effect in indirect EMF is reduced compared with direct EMF for the following reasons: the impact force caused by the collision between the sheet and die is balanced by the pressure provided by the rubber; the sheet is always under tensile stress state due to the friction force provided by rubber; the remaining kinetic energy of sheet after collision with the die is absorbed by rubber. Therefore, the rebound effect in indirect EMF is suppressed compared with direct EMF. So, the fittability of the workpiece is improved, which results in a better forming quality. [ABSTRACT FROM AUTHOR]

The relationship between microstructure and flow behaviour has attracted attention from many researchers for the past decades, whilst the influences of dislocation and recrystallization on flow stress have not been well understood, which led to failure in flow stress prediction at high temperature compressions. In this work, we tried to provide a novel explanation of the relationship between microstructure evolutions and flow behaviour, and the influence of dislocation and recrystallization on flow stress was investigated. A dislocation based flow stress model was proposed and applied for 300M steel at the strain rate of 0.01–10 s−1 and the temperature of 950–1150 °C. Results showed the established model could predict the flow stress both at constant strain rate conditions and at variable strain rate conditions. The present investigation is helpful to a better understanding of hardening and softening mechanisms in hot compression of 300M steel. [ABSTRACT FROM AUTHOR]