Search

The mechanical properties of a defect-free laser melting (PBF-LB) deposit of an AISI 316L steel alloy were assessed by means of an instrumented indentation test (IIT), at both the macro- and nano-scales. The inherent non-equilibrium microstructure of the alloy was chemically homogenous and consisted of equiaxed grains and large-elongated grains (under the optical microscope) with irregular outlines composed of a much finer internal cell structure (under the scanning electron microscope). Berkovich and Vickers indenters were used to assess the indentation properties across individual grains (nano) and over multiple grains (macro), respectively. The nano-indentation over the X-Y plane revealed nearly constant indentation modulus across an individual grain but variable on average within different grains whose value depended on the relative orientation of the individual grain. The macro-indentation test was conducted to analyze the tensile-like properties of the polycrystalline SS 316L alloy over the X-Y and Y-Z planes. The macro-indentation test provided a reliable estimate of the ultimate tensile strength (UTS-like) of the alloy. Other indentation properties gave inconsistent results, and a post factum analysis was, therefore, conducted, by means of a new approach, to account for the presence of residual stresses. The already existing indentation data were supplemented with new repeated indentation tests to conduct a detailed analysis of the relaxation ability of compressive and tensile residual stresses. The developed methodology allows the effect of residual stresses and the reliability of measured macro-indentation properties to be examined as a function of a small group of indentation parameters. [ABSTRACT FROM AUTHOR]

This study explores the tensile strength of adhesive joints in steel, focusing on the influence of heat treatment and diverse surface modifications. Results indicate a notable relationship between annealing temperature and tensile strength, with the most favorable outcomes identified at 90 min and 165 °C. Particularly, surfaces treated through turning, sandblasting, and plasma treatment (type C) consistently outperformed other methods. A standout revelation emerged from the turned, sandblasted, and plasma-treated surface (C), showcasing an exceptional tensile strength of 69.06 MPa. Load-holding tests underscored its resilience under diverse load conditions. Surface analyses, including roughness measurements, wetting characteristics, and Scanning Electron Microscope imaging, provided valuable insights into structural transformations induced by different treatments. Chemical composition examinations unveiled significant alterations post-plasma treatment, impacting surface chemistry and contributing to an outstanding tensile strength of 67.63 MPa. In essence, this research offers a glimpse into the nuanced factors influencing adhesive joint strength in steel. The turned, sandblasted, and plasma-treated surface emerges as a promising avenue, sparking further curiosity into the underlying mechanisms propelling superior tensile strength in adhesive joints. [ABSTRACT FROM AUTHOR]

To further explore the quasi-static mechanical characteristics of composite solid propellants at low strain rates, an investigation was conducted on the mechanical behavior and damage mechanisms of a four-component hydroxy-terminated polybutadiene (HTPB) propellant by means of experiments and numerical simulation. A uniaxial tensile test and scanning electron microscope (SEM) characterization experiment were carried out. A microstructural model, which accurately represents the mesoscopic structure, was developed via the integration of micro-CT scanning and image-processing techniques. The constructed microstructural model was utilized to conduct a numerical simulation of the mechanical behavior. The experimental results demonstrated that the maximum tensile strength increases with increasing strain rate, and the primary cause of propellant failure at low strain rates is the dewetting phenomenon occurring at the interface between the larger particles and the matrix. The maximum tensile strength is 0.48 MPa when the strain rate is 0.00119 s−1, and the maximum tensile strength is 0.37 MPa when the strain rate is 0.000119 s−1. The simulation results indicated a consistent trend in variation when comparing the simulation and experimental curves. This suggested that the established model exhibits a high level of reliability, and provides a promising approach for carrying out microstructural simulations of heterogeneous propellants in future. The mechanical behavior of the propellant can be effectively described by utilizing a mesoscopic finite element model that incorporates the superelastic constitutive model of the matrix and the bilinear cohesive model. This framework facilitates the representation of mesoscopic damage evolution, which consequently provides insights into the damage mechanism. Additionally, the utilization of such models assists in compensating for the limitations of damage evolution characterization experiments. [ABSTRACT FROM AUTHOR]

Mg-3Sn-1Mn-xLa alloy bars were prepared using backward extrusion, and the effects of the La content on the microstructures and mechanical properties of the alloy were systematically studied using an optical microscope (OM), X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and tensile tests. The results of this research show that the Mg2Sn phases were mainly formed at the α-Mg grain boundaries and within the grains in the Mg-3Sn-1Mn alloy. After adding a certain amount of La, the plate-shaped MgSnLa compounds consisting of Mg17La2, Mg2Sn, and La5Sn3 gradually disappeared in the α-Mg matrix and grain boundaries. With an increase in La content, the Mg2Sn phase in the crystal was gradually refined and spheroidized. When the content of La reached 1.5%, the tensile strength of the alloy reached 300 Mpa and the elongation reached 12.6%, i.e., 25% and 85% increases, respectively, compared to the Mg-3Sn-1Mn alloy. The plate-shaped compound of Mg-3Sn-1Mn-1.5La had an average length of 3000 ± 50 nm, while the width was 350 ± 10 nm. Meanwhile, the extruded alloy's grain size was significantly refined, and there were many small cleavage steps and dimples in the fracture surface of the alloy. When the La content reached 2%, the alloy performance showed a downward trend due to the coarsening of the grains. The formed plate-shaped MgSnLa compounds and Mg2Sn phases were consistent with the α-Mg matrix. They effectively pinned the dislocations and grain boundaries, which is the main reason for strengthening the mechanical properties of extrusion alloys. [ABSTRACT FROM AUTHOR]

In this study, ground glass powder and crushed waste glass were used to replace coarse and fine aggregates. Within the scope of the study, fine aggregate (FA) and coarse aggregate (CA) were changed separately with proportions of 10%, 20%, 40%, and 50%. According to the mechanical test, including compression, splitting tensile, and flexural tests, the waste glass powder creates a better pozzolanic effect and increases the strength, while the glass particles tend to decrease the strength when they are swapped with aggregates. As observed in the splitting tensile test, noteworthy progress in the tensile strength of the concrete was achieved by 14%, while the waste glass used as a fractional replacement for the fine aggregate. In samples where glass particles were swapped with CA, the tensile strength tended to decrease. It was noticed that with the adding of waste glass at 10%, 20%, 40%, and 50% of FA swapped, the increase in flexural strength was 3.2%, 6.3%, 11.1%, and 4.8%, respectively, in amount to the reference one (6.3 MPa). Scanning electron microscope (SEM) analysis consequences also confirm the strength consequences obtained from the experimental study. While it is seen that glass powder provides better bonding with cement with its pozzolanic effect and this has a positive effect on strength consequences, it is seen that voids are formed in the samples where large glass pieces are swapped with aggregate and this affects the strength negatively. Furthermore, simple equations using existing data in the literature and the consequences obtained from the current study were also developed to predict mechanical properties of the concrete with recycled glass for practical applications. Based on findings obtained from our study, 20% replacement for FA and CA with waste glass is recommended. [ABSTRACT FROM AUTHOR]

Hydrogels belong to the group of polymers that are more and more often considered as innovative dressing materials. It is important to develop materials showing the most advantageous properties from the application viewpoint wherein in the case of hydrogels, the type and the amount of the crosslinking agent strongly affect their properties. In this work, PVP-based hydrogels containing Aloe vera juice and L-ascorbic acid were obtained via UV-induced polymerization. Next, their surface morphology (via both optical, digital and scanning electron microscope), sorption capacity, tensile strength, and elongation were characterized. Their structure was analyzed via FT-IR spectroscopy wherein their impact on the simulated body liquids was verified via regular pH and temperature measurements of these liquids during hydrogels' incubation. It was demonstrated that as the amount of the crosslinker increased, the polymer structure was more wrinkled. Next, hydrogels showed relatively smooth and only slightly rough surface, which was probably due to the fact that the modifiers filled also the outer pores of the materials. Hydrogels demonstrated buffering properties in all incubation media, wherein during the incubation the release of Aloe vera juice probably took place as evidenced by the decrease in the pH of the incubation media and the disappearance of the absorption band deriving from the polysaccharides included in the composition of this additive. Next, it was proved that as the amount of the crosslinker increased, hydrogels' crosslinking density increased and thus their swelling ratio decreased. Hydrogels obtained using a crosslinking agent with higher average molecular weight showed higher swelling ability than the materials synthesized using crosslinker with lower average molecular weight. Moreover, as the amount of the crosslinking agent increased, the tensile strength of hydrogels as well as their percentage elongation also increased. [ABSTRACT FROM AUTHOR]

With the crisis awareness of global warming and natural disasters, utilization of local wood has drawn increasing attention in achieving the Sustainable Development Goals (SDGs). It is necessary to investigate the deformation and fracture of the structural tissue in wood in order to improve the safety and reliability of wood application. However, deformation and fracture mechanisms of the structural tissue in each annual ring are unknown. The mechanical characteristics of wood are reflected in the properties of earlywood and latewood. In the present study, microstructural observation and tensile tests were conducted to examine the relationship between the mechanical properties and fracture behavior of latewood in the growth direction in Japanese cedar. Brittle fracture behavior of the latewood specimen was confirmed based on the tensile stress–strain curve and features of the fracture surface. Moreover, two fracture modes, tensile fracture and shear fracture, were recognized. Weibull analysis of tensile strength in each fracture mode was performed to evaluate the reliability and utility of brittle latewood. Lastly, two fracture mechanisms were discussed based on the failure observation findings by a scanning electron microscope. [ABSTRACT FROM AUTHOR]

High strength and toughness are achieved in the Mg-4.96Gd-2.44Y-0.43Zr alloy by multidirectional impact forging (MDIF). The forged sample has a fine-grained microstructure with an average grain size of ~5.7 µm and a weak non-basal texture, and it was characterized by an optical microscope (OM), scanning electron microscope (SEM), and electron back-scattering diffraction (EBSD). Tensile results exhibit the tensile yield strength (TYS) and static toughness (ST) of as-homogenized alloy dramatically increased after forging and aging, i.e., the TYS increased from 135 − 5 + 4 MPa to 337 − 2 + 2 MPa, and the ST enhanced from 22. 0 − 0.5 + 0.3 MJ/m3 to 50. 4 − 5.4 + 5.3 MJ/m3. Specifically, the forged Mg-Gd-Y-Zr alloy owns higher TYS than that of commercial rolled WE54 (Mg-5.25Y-3.5Nd-0.5Zr) and WE43 (Mg-4.0Y-3.0Nd-0.5Zr) alloys. [ABSTRACT FROM AUTHOR]

In the present paper, the Mg-11Gd-2Y-1Zn alloys with different Al addition were fabricated by the gravity permanent mold method. The effect of Al content on microstructure evolution and mechanical properties of as-cast Mg-11Gd-2Y-1Zn alloy was studied by metallographic microscope, scanning electron microscope, XRD and tensile testing. The experimental results showed that the microstructure of as-cast Mg-11Gd-2Y-1Zn alloy consisted of α-Mg phase and island-shaped Mg3 (RE, Zn) phase. When Al element was added, Al2RE phase and lamellar Mg12REZn (LPSO) phase were formed in the Mg-11Gd-2Y-1Zn alloy. With increasing Al content, LPSO phase and Mg3 (RE, Zn) phase gradually decreased, while Al2RE phase gradually increased. There were only α-Mg and Al2RE phases in the Mg-11Gd-2Y-1Zn-5Al alloy. With the increase of Al content, the grain size decreased firstly and then increased. When the Al content was 1 wt.%, the grain size of the alloy was the minimum value (28.9 μm). The ultimate tensile strength and elongation increased firstly and then decreased with increasing Al addition. And the fracture mode changed from intergranular fracture to transgranular fracture with increasing addition. When Al addition was 1 wt.%, the maximum ultimate tensile strength reached 225.6 MPa, and the elongation was 7.8%. When the content of Al element was 3 wt.%, the maximum elongation reached 10.2% and the ultimate tensile strength was 207.7 MPa. [ABSTRACT FROM AUTHOR]

Electrospinning is an innovative new fibre technology that aims to design and fabricate membranes suitable for a wide range of tissue engineering (TE) applications including vascular grafts, which is the main objective of this research work. This study dealt with fabricating and characterising bilayer structures comprised of an electrospun sheet made of polycaprolactone (PCL, inner layer) and an outer layer made of poly lactic-co-glycolic acid (PLGA) and a coaxial porous scaffold with a micrometre fibre structure was successfully produced. The membranes' propriety for intended biomedical applications was assessed by evaluating their morphological structure/physical properties and structural integrity when they underwent the degradation process. A scanning electron microscope (SEM) was used to assess changes in the electrospun scaffolds' structural morphology such as in their fibre diameter, pore size (μm) and the porosity of the scaffold surface which was measured with Image J software. During the 12-week degradation process at room temperature, most of the scaffolds showed a similar trend in their degradation rate except the 60 min scaffolds. The coaxial scaffold had significantly less mass loss than the bilayer PCL/PLGA scaffold with 1.348% and 18.3%, respectively. The mechanical properties of the fibrous membranes were measured and the coaxial scaffolds showed greater tensile strength and elongation at break (%) compared to the bilayer scaffolds. According to the results obtained in this study, it can be concluded that a scaffold made with a coaxial needle is more suitable for tissue engineering applications due to the improved quality and functionality of the resulting polymeric membrane compared to the basic electrospinning process. However, whilst fabricating a vascular graft is the main aim of this research work, the biological data will not present in this paper. [ABSTRACT FROM AUTHOR]

The current study aimed to evaluate the characteristics and the effects of degradation on the structural properties of Poly(lactic-co-glycolic acid) (PLGA)- and polycaprolactone (PCL)-based nanofibrous scaffolds. Six scaffolds were prepared by electrospinning, three with PCL 15% (w/v) and three with PLGA 10% (w/v), with electrospinning processing times of 30, 60 and 90 min. Both types of scaffolds displayed more robust mechanical properties with increased spinning times. The tensile strength of both scaffolds with 90-min electrospun membranes did not show a significant difference in their strengths, as the PCL and PLGA scaffolds measured at 1.492 MPa ± 0.378 SD and 1.764 MPa ± 0.7982 SD, respectively. All membranes were shown to be hydrophobic under a wettability test. A degradation behaviour study was performed by immersing all scaffolds in phosphate-buffered saline (PBS) solution at room temperature for 12 weeks and for 4 weeks at 37 °C. The effects of degradation were monitored by taking each sample out of the PBS solution every week, and the structural changes were investigated under a scanning electron microscope (SEM). The PCL and PLGA scaffolds showed excellent fibre structure with adequate degradation, and the fibre diameter, measured over time, showed slight increase in size. Therefore, as an example of fibre water intake and progressive degradation, the scaffold's percentage weight loss increased each week, further supporting the porous membrane's degradability. The pore size and the porosity percentage of all scaffolds decreased substantially over the degradation period. The conclusion drawn from this experiment is that PCL and PLGA hold great promise for tissue engineering and regenerative medicine applications. [ABSTRACT FROM AUTHOR]

Diatomaceous earth are sediments of unicellular algal skeletons with a well-defined hierarchical structure. Despite many tests conducted on systems using diatomaceous earth and epoxy resins, we can find many differences in the methods of acquisition and characteristics of the composite, which may considerably affect the results. In our study, we have conducted tests to verify the impact of the method of obtaining samples and the degassing of the composite on its mechanical properties and standard deviation. The samples were cast in glass moulds and silicone moulds and then subjected to testing for their mechanical and functional properties, imaging with the use of an optical microscope and a scanning electron microscope. The tests have shown that, for samples cast in glass moulds, there is no heterogeneity within the area of the tested sample, as in the case of samples cast in silicone moulds. Silicone moulds allow for quite effective self-degassing of the resin due to the large area-to-mass ratio, and the small remaining air vesicles have a limited effect on the mechanical properties of the samples. The filler used also played a significant role. For systems containing base and rinsed diatomite, it is clear that the degassing of mixtures increases the tensile strength. For treated diatomite, the elongation at break grew along with increasing filler concentration, while for base diatomite, the improvement was observed for flexural strength and impact strength. A non-modified epoxy resin shows a tensile strength at 19.91 MPa (silicone mould cast). At the same time, the degassed, glass mould-cast systems containing 12% of base and rinsed diatoms showed a tensile strength of 27.4 MPa and 44.7 MPa, respectively. We have also observed that the higher the filler concentration, the higher were the tensile strength values, which for the rinsed diatoms reached over 55.1 MPa and for the base diatoms were maximum of 43.8 MPa. The tests, therefore, constitute a set of guidelines and recommendations for testing with the use of fillers showing an extended inner structure. [ABSTRACT FROM AUTHOR]

To enhance the mechanical properties (e.g., strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis, have been conducted. The presence of fcc annealing twins was observed in both the optical microscope (OM) and the scanning electron microscope (SEM) images. Both strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these two alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au. [ABSTRACT FROM AUTHOR]