Search

Alkali-activated slag (AAS) presents a promising alternative to ordinary Portland cement due to its cost effectiveness, environmental friendliness, and satisfactory durability characteristics. In this paper, cow dung waste was recycled as a renewable natural cellulose fiber, modified with alkali, and then added to AAS mortar. The physico-chemical characteristics of raw and modified cow dung fibers were determined through Fourier transform infrared (FTIR), X-ray diffraction (XRD), and Scanning electron microscope (SEM). Investigations were conducted on the dispersion of cow dung fibers in the AAS matrix, as well as the flowability, strength, and autogenous shrinkage of AAS mortar with varying cow dung fiber contents. The results indicated that modified fiber has higher crystallinity and surface roughness. The ultrasonic method showed superior effectiveness compared to pre-mixing and after-mixing methods. Compared with raw cow dung fibers, modified fibers led to an increase of 11.3% and 36.3% of the 28 d flexural strength and compressive strength of the AAS mortar, respectively. The modified cow dung fibers had a more significant inhibition on autogenous shrinkage, and the addition of 2 wt% cow dung fibers reduced the 7 d autogenous shrinkage of the AAS paste by 52.8% due to the "internal curing effect." This study provides an alternative value-added recycling option for cow dung fibers as a potential environmentally friendly and sustainable reinforcing raw material for cementitious materials, which can be used to develop low autogenous shrinkage green composites. [ABSTRACT FROM AUTHOR]

Global warming has led to a change in climatic conditions. Since 2006, drought has contributed to a reduction of food production and other agriculture-based products in many countries. The accumulation of greenhouse gases in the atmosphere has caused some changes in the composition of fruits and vegetables, making them less nutritious. To analyse this situation, a study was conducted on the effect of drought on the quality of fibres provided by the main fibre crops in Europe, namely flax (Linum usitatissimum). The experiment consisted of growing flax under controlled comparative conditions with designed different irrigation levels, such as 25%, 35% and 45% field soil moisture. Three varieties of flax were grown in 2019, 2020 and 2021 in the greenhouses of the Institute of Natural Fibres and Medicinal Plants in Poland. Fibre parameters, such as linear density, length and strength, were evaluated according to relevant standards. In addition, scanning electron microscope images of the cross-section and longitudinal view of the fibres were analysed. The results of the study indicated that deficiency of water during the flax growing season resulted in lowering of fibre linear density and tenacity. [ABSTRACT FROM AUTHOR]

This article focuses on the mechanical property analysis of important models omitted in many scientific papers (thin-walled specimens) printed from innovative material—such as PLA + bronze composite—using fused deposition modelling technology. It discusses the printing process, the measurement of the specimen geometry, the static tensile strength tests and the microscopic examinations conducted with a scanning electron microscope. The findings of this study could be used as an input to further research into the accuracy of filament deposition and the modification of base materials with bronze powder and for the optimization of the machine design, e.g., with the use of cell structures. The experimental results indicated that the thin-walled models fabricated using FDM showed substantial differences in tensile strength, depending on the specimen's thickness and the printing orientation. It was shown that it was not possible to test thin-walled models located on the building platform along the Z axis due to the lack of sufficient adhesion between the layers. [ABSTRACT FROM AUTHOR]

Pollutants and infectious diseases can spread through air with airborne droplets and aerosols. A respiratory mask can decrease the amount of pollutants we inhale and it can protect us from airborne diseases. With the onset of the COVID-19 pandemic, masks became an everyday item used by a lot of people around the world. As most of them are for a single use, the amount of non-recyclable waste increased dramatically. The plastic from which the masks are made pollutes the environment with various chemicals and microplastic. Here, we investigated the time- and size-dependent filtration efficiency (FE) of aerosols in the range of 25.9 to 685.4 nm of five different natural materials whose FE was enhanced using electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF) fibres. A scanning electron microscope (SEM) was used to determine the morphology and structure of the natural materials as well as the thickness of the PVDF fibres, while the phase of the electrospun fibres was determined by Raman spectroscopy. A thin layer of the electrospun PVDF fibres with the same grammage was sandwiched between two sheets of natural materials, and their FE increased up to 80%. By varying the grammature of the electrospun polymer, we tuned the FE of cotton from 82.6 to 99.9%. Thus, through the optimization of the grammage of the electrospun polymer, the amount of plastic used in the process can be minimized, while achieving sufficiently high FE. [ABSTRACT FROM AUTHOR]

A persistent rise in the costs of construction materials has led to the need to address this problem in line with the Sustainable Development Goals. This research employed vegetal soft and rigid fibers in a screed mortar to produce a sustainable fabric–cement matrix. Four different vegetal-dried fibers (hemp, flax, miscanthus, and bamboo) with dosages of 0.4, 0.6, 0.8, 1.2, 2, and 4 kg/m3 were used. Laboratory investigations were slump test, bulk density, air occluded, shrinkage, and mechanical strength. Scanning Electron Microscope (SEM) assessments were performed and analyzed on the natural fibers and the screed formulation. The results highlight that fiber dosages significantly influence the above-mentioned properties. [ABSTRACT FROM AUTHOR]

Resin-based friction materials (RBFM) are widely used in the fields of automobiles, agriculture machinery and engineering machinery, and they are vital for safe and stable operation. In this paper, polymer ether ketone (PEEK) fibers were added to RBFM to enhance its tribological properties. Specimens were fabricated by wet granulation and hot-pressing. The relationship between intelligent reinforcement PEEK fibers and tribological behaviors was investigated by a JF150F-II constant-speed tester according to GB/T 5763-2008, and the worn surface morphology was observed using an EVO-18 scanning electron microscope. The results showed that PEEK fibers can efficiently enhance the tribological properties of RBFM. A specimen with 6 ωt% PEEK fibers obtained the optimal tribological performance, the fade ratio was −6.2%, which was much higher than that of the specimen without the addition of PEEK fibers, the recovery ratio was 108.59% and the wear rate was the lowest, which was 1.497 × 10−7 cm3/(Nm)−1. The reason for the enhancing tribological performance was that, on the one hand, PEEK fibers have a high strength and modulus which can enhance the specimens at lower temperatures; on the other hand, molten PEEK at high temperatures can also promote the formation of secondary plateaus, which are beneficial for friction. The results in this paper can lay a foundation for future studies on intelligent RBFM. [ABSTRACT FROM AUTHOR]

The building and construction industry consumes a significant amount of virgin resources and minimizing the demand with alternative waste materials can provide a contemporary solution. In this study, thermal components of kraft fibres (KFs) derived from waste cardboard are investigated. The mechanical properties containing KFs within concrete composites are evaluated. Metakaolin (MK) and KFs were integrated into concrete samples as a partial substitute for cement. Silica Fume (SF) was applied to the KF (SFKFs) with a view to enhancing the fibre durability. The results indicated that there was a reduction in compressive strength of 44 and 56% when 10% raw and modified KFs were integrated, respectively. Raw, fibre and matrix-modified samples demonstrated a 35, 4 and 24% flexural strength reduction, respectively; however, the tensile strength improved by 8% when the matrix was modified using MK and SFKF. The morphology of the fibres was illustrated using a scanning electron microscope (SEM), with an energy dispersion X-ray spectroscopy (EDS) provision and Fourier transform infrared spectroscopy (FT-IR) employed to gain insights into their chemical nature. The thermal, calorimetric and combustion attributes of the fibres were measured using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and pyrolysis combustion flow calorimetry (PCFC). SFKFs showed a lower heat release capacity (HRC), demonstrating a lower combustion propensity compared to raw KFs. Furthermore, the 45% decreased peak heat release rate (pHRR) of SFKFs highlighted the overall reduction in the fire hazards associated with these materials. TGA results also confirmed a lower mass weight loss of SFKFs at elevated temperatures, thus corroborating the results from the PCFC runs. [ABSTRACT FROM AUTHOR]

There is a need to develop new construction materials with improved mechanical performance and durability that are low-priced and have environmental benefits at the same time. This paper focuses on the rheological, mechanical, morphological, and durability properties of synthetic and steel fiber reinforced self-compacting concrete (SCC) containing 5–15% metakaolin (M) by mass as a green replacement for Portland cement. Testing of the fresh mixes included a slump-flow test, density, and porosity tests. Mechanical properties were determined through compression and flexural strength. A rapid chloride penetrability test (RCPT) and the chloride migration coefficient were used to assess the durability of the samples. A scanning electron microscope (SEM) with energy dispersion spectrometry (EDS) was used to study the concrete microstructure and the interfacial transition zone (ITZ). The results show that a combination of metakaolin and hybrid fibers has a negative effect on the flowability of SCC. In contrast, the inclusion of M and hybrid fibers has a positive effect on the compressive and flexural strength of SCC. The fracture of SCC samples without fibers was brittle and sudden, unlike the fiber-reinforced SCC samples, which could still transfer a considerable load with increasing crack mouth opening deflection. Overall, the chloride migration coefficients were reduced by up to 71% compared to the control mix. The chloride reduction is consistent with the resulting compact concrete microstructure, which exhibits a strong bond between fibers and the concrete matrix. [ABSTRACT FROM AUTHOR]

To improve the flexural properties of cemented soils reinforced with fibers and avoid their brittle failure when subjected to complex loading conditions, a simple and cost-effective technique was explored to facilitate their application in retaining walls. In this study, how different fiber surface modifications, i.e., alkali treatment, acid treatment and silane coupling agent treatment, as well as different fiber contents, i.e., 0%, 0.25%, 0.5% and 1%, affect the bending properties of cemented soils was investigated by conducting three-point bending tests on notched beams. The digital image correlation (DIC) technology was used to examine the crack propagation process and the strain field distribution of cracks in specimens in the flexural tests. The results show that all fiber surface modifications increased peak strength and fracture energy, for example, the fracture energy of specimens AN1, AH1 and AK1 was increased by 180.4%, 121.5% and 155.4%, respectively, compared to PVA1. In addition, the crack tip strain, crack propagation rate and the initial crack width of the modified specimens were lower than those before modification. Lastly, scanning electron microscope (SEM) and mercury intrusion porosimetry tests were adopted to reveal the mechanism of bending performance in cemented soils reinforced by fiber surface modifications. [ABSTRACT FROM AUTHOR]

Polyurethane cement (PUC) is now commonly used in the reinforcement of old bridges, which exhibit various issues such as poor toughness, temperature-sensitive mechanical properties, and brittle failure. These problems can lead to the failure of the reinforcement effect of the PUC on old bridges in certain operating environments, leading to the collapse of such reinforced bridges. In order to alleviate these shortcomings, in this study, the toughness of PUC is improved by adding polyvinyl alcohol (PVA) fiber, carbon fiber, and steel fiber. In addition, we study the change law of the flexural strength of PUC between −40 °C and +40 °C. The control parameters evaluated are fiber type, fiber volume ratio, and temperature. A series of flexural tests and scanning electron microscope (SEM) test results show that the flexural strength first increases and then decreases with the increase in the volume-doping ratio of the three fibers. The optimum volume-mixing ratios of polyvinyl alcohol (PVA) fiber, carbon fiber, and steel fiber are 0.3%, 0.04% and 1%, respectively. Excessive addition of fiber will affect the operability and will adversely affect the mechanical properties. The flexural strength of both fiber-reinforced and control samples decreases with increasing temperature. Using the flexural test results, a two-factor (fiber content, temperature) BP neural network flexural strength prediction model is established. It is verified that the model is effective and accurate, and the experimental value and the predicted value are in good agreement. [ABSTRACT FROM AUTHOR]

The paper aims to investigate the influence of basalt fiber (BF) on the crack resistance of the asphalt mixture and conduct a mechanical analysis. First, two typical asphalt mixtures, namely AC-13 and SMA-13, were designed. The impact of BF on the mixture design results was analyzed. Then, several macroscopic tests, namely the four-point bending test, indirect tensile test, and semicircular bending test (SCB), were conducted to assess the effect of BF on the cracking resistance of asphalt mixtures. Finally, the influence of BF on the cracking resistance of asphalt mixtures was analyzed based on an environmental scanning electron microscope (ESEM) observation. The results show that: (1) BF increases the optimal asphalt content of AC13 and decreases the optimal asphalt content of SMA-13, which is caused by the different asphalt-absorption capacity of BF and lignin fiber (LF). (2) BF enhances both the fatigue crack resistance and temperature crack resistance of asphalt mixtures. The enhancement on the SMA-13 is more significant, indicating that the enhancement of BF on asphalt mixtures is related to the type of aggregate gradation. (3) BFs in the asphalt mixture lap each other to form a spatial network structure. Such structure can effectively improve the crack resistance of the mixture by dispersing the load stress and preventing the flow of asphalt mastic. The study results provide an effective method to design crack-resistant asphalt mixtures. [ABSTRACT FROM AUTHOR]

The study investigated the effectiveness of the combination of chemical and physical methods of natural fibers' modification. The long flax fibers were subjected to various types of modification. These were silanization, plasma modification and a combination of these methods. For the silanization process, two types of silanes were used: amino- and vinylsilane. The application of structurally different compounds allowed us to acquire knowledge about the effect of the modifier structure on its properties. Various properties of flax fibers were investigated, comparing the results before and after different modification processes. The flammability of prepared samples were tested by pyrolysis combustion flow calorimeter (PCFC). In the effect of the natural fibers' modifications, flammability was reduced even by 30%. The thermal stability of modified fibers increased. The FTIR tests of the gases released during thermal degradation of the tested fibers allowed us to determine the important compounds and prove a lower degree of flax-fiber decomposition after modification. Flax fibers were also tested to evaluate their physical properties (linear mass, average diameter, aspect ratio and hygroscopicity). Changes in surface morphology were observed by scanning electron microscope (SEM). The properties of natural fibers improved significantly, thus contributing to an increase in their suitability for the use in composites. [ABSTRACT FROM AUTHOR]