Search

The effect of hydrogen content on the deformation and fracture behavior of 27Cr−4Mo−2Ni super ferritic stainless steel (SFSS) was investigated in this study. It was shown that the plasticity and yield strength of SFSS were very susceptible to hydrogen content. The introduction of hydrogen led to a significant decrease in elongation and a concurrent increase in yield strength. Nevertheless, a critical threshold was identified in the elongation reduction, after which the elongation remained approximately constant even with more hydrogen introduced, while the yield strength exhibited a monotonic increase with increasing hydrogen content within the experimental range, attributed to the pinning effect of the hydrogen Cottrell atmosphere on dislocations. Furthermore, the hydrogen-charged SFSS shows an apparent drop in flow stress after upper yielding and a reduced work hardening rate during the subsequent plastic deformation. The more hydrogen is charged, the more the flow stress drops, and the lower the work hardening rate becomes. [ABSTRACT FROM AUTHOR]

Herein, the toughening mechanism and effects of 3-(aminopropyl)triethoxysilane (3-APTES) intercalation in calcium–silicate–hydrate (CSH) structures were investigated through molecular dynamics simulations. CSH established a model using 11 Å-tobermorite to simulate the tensile properties, toughness, adsorption energy, average orientation displacement and radial distribution function of 3-APTES intercalation at different Ca/Si ratios under conditions of a CVFF force field, an NVT system, and 298 K temperature. Simulation results demonstrate that 3-APTES alters the fracture process of CSH and effectively enhances its tensile properties and toughness. The presence of 3-APTES molecules increases the energy required to destroy CSH, thereby increasing the adsorption energy of CSH crystals. Furthermore, 3-APTES molecules effectively increase the atom density within the CSH structure. As the Ca/Si ratio increases, Ca–O bond formation is enhanced, with noticeable aggregation occurring because of modification by 3-APTES within the CSH structure. This study found that 3-APTES organic compounds can effectively improve the tensile, toughness, adsorption and other properties of the CSH structure, and further improve the microstructure of CSH. [ABSTRACT FROM AUTHOR]

To reduce the noise generated by large mechanical equipment, a stackable and expandable acoustic metamaterial with multiple tortuous channels (SEAM–MTCs) was developed in this study. The proposed SEAM–MTCs consisted of odd panels, even panels, chambers, and a final closing plate, and these component parts could be fabricated separately and then assembled. The influencing factors, including the number of layers N, the thickness of panel t0, the size of square aperture a, and the depth of chamber T0 were investigated using acoustic finite element simulation. The sound absorption mechanism was exhibited by the distributions of the total acoustic energy density at the resonance frequencies. The number of resonance frequencies increased from 13 to 31 with the number of layers N increasing from 2 to 6, and the average sound absorption coefficients in [200 Hz, 6000 Hz] was improved from 0.5169 to 0.6160. The experimental validation of actual sound absorption coefficients in [200 Hz, 1600 Hz] showed excellent consistency with simulation data, which proved the accuracy of the finite element simulation model and the reliability of the analysis of influencing factors. The proposed SEAM–MTCs has great potential in the field of equipment noise reduction. [ABSTRACT FROM AUTHOR]

The limited occupied space and various noise spectrum requires an adjustable sound absorber with a smart structure and tunable sound absorption performance. The hexagonal acoustic metamaterial cell of the multiple parallel-connection resonators with tunable perforating rate was proposed in this research, which consisted of six triangular cavities and six trapezium cavities, and the perforation rate of each cavity was adjustable by moving the sliding block along the slideway. The optimal geometric parameters were obtained by the joint optimization of the acoustic finite element simulation and cuckoo search algorithm, and the average sound absorption coefficients in the target frequency ranges of 650–1150 Hz, 700–1200 Hz and 700–1000 Hz were up to 0.8565, 0.8615 and 0.8807, respectively. The experimental sample was fabricated by the fused filament fabrication method, and its sound absorption coefficients were further detected by impedance tube detector. The consistency between simulation data and experimental data proved the accuracy of the acoustic finite element simulation model and the effectiveness of the joint optimization method. The tunable sound absorption performance, outstanding low-frequency noise reduction property, extensible outline structure and efficient space utilization were favorable to promote its practical applications in noise reduction. [ABSTRACT FROM AUTHOR]

Titanium alloys are the ideal material for a wide range of structural applications, but their high cost compared to other metals hinders their adoption. Powder metallurgy and cheap alloying elements can be used to create new Ti alloys. In this study, the simultaneous addition of Al and Mn is considered to manufacture and characterise ternary Ti-2.5Al-Mn alloys obtained via pressing and sintering by varying the Mn content (1–10 wt.%). It is found that the addition of the alloying elements reduces compressibility. Consequently, the amount of porosity increases (8.5 → 10.8%) with the amount of Mn as the alloys were processed under the same conditions. The progressive addition of Mn refines the classical lamellar microstructure and, eventually, transforms it into an equiaxed β-grain structure with acicular α grains. The microstructural changes lead to continuous increases in strength (ultimate tensile strength: 694 → 851 MPa) and hardness (225 → 325 HV30) with an associated loss of ductility (elongation to failure: 13.9 → 1.0%). However, the obtained ternary Ti-2.5Al-Mn alloys have similar or better overall mechanical behaviour than most of the binary Ti-Mn alloys obtained through a variety of manufacturing methods. [ABSTRACT FROM AUTHOR]

In order to achieve a balance between sound insulation and ventilation, a novel acoustic metamaterial of air-permeable multiple-parallel-connection folding chambers was proposed in this study that was based on Fano-like interference, and its sound-insulation performance was investigated through acoustic finite element simulation. Each layer of the multiple-parallel-connection folding chambers consisted of a square front panel with many apertures and a corresponding chamber with many cavities, which were able to extend both in the thickness direction and in the plane direction. Parametric analysis was conducted for the number of layers nl and turns nt, the thickness of each layer L2, the inner side lengths of the helical chamber a1, and the interval s among the various cavities. With the parameters of nl = 10, nt = 1, L2 = 10 mm, a1 = 28 mm, and s = 1 mm, there were 21 sound-transmission-loss peaks in the frequency range 200–1600 Hz, and the sound-transmission loss reached 26.05 dB, 26.85 dB, 27.03 dB, and 33.6 dB at the low frequencies 468 Hz, 525 Hz, 560 Hz, and 580 Hz, respectively. Meanwhile, the corresponding open area for air passage reached 55.18%, which yielded a capacity for both efficient ventilation and high selective-sound-insulation performance. [ABSTRACT FROM AUTHOR]

A Helmholtz resonator (HR) with an embedded aperture is an effective acoustic metamaterial for noise reduction in the low-frequency range. Its sound absorption property is significantly affected by the aperture shape. Sound absorption properties of HRs with the embedded aperture for various tangent sectional shapes were studied by a two-dimensional acoustic finite element simulation. The sequence of resonance frequency from low to high was olive, common trapeziform, reverse trapeziform, dumbbell and rectangle. Meanwhile, those HRs for various cross-sectional shapes were investigated by a three-dimensional acoustic finite element simulation. The sequence of resonance frequency from low to high were round, regular hexagon, square, regular triangle and regular pentagon. Moreover, the reason for these phenomena was analyzed by the distributions of sound pressure, acoustic velocity and temperature. Furthermore, on the basement of the optimum tangent and cross-sectional shape, the sound absorption property of parallel-connection Helmholtz resonators was optimized. The experimental sample with optimal parameters was fabricated, and its average sound absorption coefficient reached 0.7821 in 500–820 Hz with a limited thickness of 30 mm. The research achievements proved the significance of aperture shape, which provided guidance for the development of sound absorbers in the low-frequency range. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA)/poly(ε-caprolactone) (PCL) blends have exhibited good shape memory properties and degradable characteristics in various 4D printing fields such as biomedicine, flexible electronics, and soft robotics, where the service temperature fluctuates easily by environment temperature and polymer characteristics. In this work, printed PLA/PCL 4D samples with different infill densities were prepared by material extrusion printing of pre-extruded filaments and characterized under different temperatures. The results show that the microstructures of printed samples are not influenced by printing process and have similar unique orientation as that of filaments. The thermal properties are stable and show obvious phase transition temperatures, while the mechanical properties decrease slightly in low temperature region and then decrease rapidly when temperature is over 60 °C. The increase in infill density can further improve the storage modulus more than 40% and have no significant influence on the thermal properties. The printed samples also exhibit good shape memory performances with fast recovery speeds less than 22 s. Furthermore, a two-step model is provided to predict the effective modulus of printed PLA/PCL samples and agrees well with experimental data. The results prove that temperature and infill density have different influences on the thermal, mechanical and shape memory properties of PLA/PCL blends. [ABSTRACT FROM AUTHOR]

The chemical corrosion aging of plutonium is a very important topic. It is easy to be corroded and produces oxidation products of various valence states because of its 5f electron orbit between local and non-local. On the one hand, the phase diagram of plutonium and oxygen is complex, so there is still not enough research on typical structural phases. On the other hand, most of the studies on plutonium oxide focus on PuO2 and Pu2O3 with stoichiometric ratio, while the understanding of non-stoichiometric ratio, especially for Pu2O3-x, is not deep enough. Based on this, using the DFT + U theoretical scheme of density functional theory, we have systematically studied the structural stability, lattice parameters, electronic structure, mechanical and optical properties of six typical high temperature phases of β -Pu2O3, α -Pu2O3, γ -Pu2O3, PuO, α -PuO2, γ -PuO2. Further, the mechanical properties and optical behavior of Pu2O3-x under different oxygen vacancy concentrations are analyzed and discussed in detail. The result shows that the elasticity modulus of single crystal in mechanical properties is directly related to the oxygen/plutonium ratio and crystal system. As the number of oxygen vacancies increases, the mechanical constants continue to increase. In terms of optical properties, PuO has the best optical properties, and the light absorption rate decreases with the increase of oxygen vacancy concentration. [ABSTRACT FROM AUTHOR]

The mechanical properties of resin samples in low-force stereolithography additive manufacturing were affected by the printing orientation, and were investigated and optimized to achieve excellent single or comprehensive tensile strength, compressive strength, and flexural modulus. The resin samples were fabricated using a Form3 3D printer based on light curing technology according to the corresponding national standards, and they were detected using a universal testing machine to test their mechanical properties. The influence of the printing orientation was represented by the rotation angle of the resin samples relative to the x–axis, y–axis and z–axis, and the parameters was selected in the range 0°–90° with an interval of 30°. The multiple regression models for the mechanical properties of the prepared resin samples were obtained based on least square estimation, which offered a foundation from which to optimize the parameters of the printing orientation by cuckoo search algorithm. The optimal parameters for the tensile strength, compressive strength and flexural modulus were 'α = 45°, β = 25°, γ = 90°', 'β = 0°, β = 51°, γ = 85°' and 'α = 26°, β = 0°, γ = 90°', respectively, which obtained the improvements of 80.52%, 15.94%, and 48.85%, respectively, relative to the worst conditions. The mechanism was qualitatively discussed based on the force analysis. The achievements obtained in this study proved that optimization of the printing orientation could improve the mechanical properties of the fabricated sample, which provided a reference for all additive manufacturing methods. [ABSTRACT FROM AUTHOR]

To achieve the broadband sound absorption at low frequencies within a limited space, an optimal design of joint simulation method incorporating the finite element simulation and cuckoo search algorithm was proposed. An acoustic metamaterial of multiple parallel hexagonal Helmholtz resonators with sub-wavelength dimensions was designed and optimized in this research. First, the initial geometric parameters of the investigated acoustic metamaterials were confirmed according to the actual noise reduction requirements to reduce the optimization burden and improve the optimization efficiency. Then, the acoustic metamaterial with the various depths of the necks was optimized by the joint simulation method, which combined the finite element simulation and the cuckoo search algorithm. The experimental sample was prepared using the 3D printer according to the obtained optimal parameters. The simulation results and experimental results exhibited excellent consistency. Compared with the derived sound absorption coefficients by theoretical modeling, those achieved in the finite element simulation were closer to the experimental results, which also verified the accuracy of this optimal design method. The results proved that the optimal design method was applicable to the achievement of broadband sound absorption with different low frequency ranges, which provided a novel method for the development and application of acoustic metamaterials. [ABSTRACT FROM AUTHOR]

For the common difficulties of noise control in a low frequency region, an adjustable parallel Helmholtz acoustic metamaterial (APH-AM) was developed to gain broad sound absorption band by introducing multiple resonant chambers to enlarge the absorption bandwidth and tuning length of rear cavity for each chamber. Based on the coupling analysis of double resonators, the generation mechanism of broad sound absorption by adjusting the structural parameters was analyzed, which provided a foundation for the development of APH-AM with tunable chambers. Different from other optimization designs by theoretical modeling or finite element simulation, the adjustment of sound absorption performance for the proposed APH-AM could be directly conducted in transfer function tube measurement by changing the length of rear cavity for each chamber. According to optimization process of APH-AM, The target for all sound absorption coefficients above 0.9 was achieved in 602–1287 Hz with normal incidence and that for all sound absorption coefficients above 0.85 was obtained in 618–1482 Hz. The distributions of sound pressure for peak absorption frequency points were obtained in the finite element simulation, which could exhibit its sound absorption mechanism. Meanwhile, the sound absorption performance of the APH-AM with larger length of the aperture and that with smaller diameter of the aperture were discussed by finite element simulation, which could further show the potential of APH-AM in the low-frequency sound absorption. The proposed APH-AM could improve efficiency and accuracy in adjusting sound absorption performance purposefully, which would promote its practical application in low-frequency noise control. [ABSTRACT FROM AUTHOR]

Acoustic metamaterials based on Helmholtz resonance have perfect sound absorption characteristics with the subwavelength size, but the absorption bandwidth is narrow, which limits the practical applications for noise control with broadband. On the basis of the Fabry–Perot resonance principle, a novel sound absorber of the acoustic metamaterial by parallel connection of the multiple spiral chambers (abbreviated as MSC-AM) is proposed and investigated in this research. Through the theoretical modeling, finite element simulation, sample preparation and experimental validation, the effectiveness and practicability of the MSC-AM are verified. Actual sound absorption coefficients of the MSC-AM in the frequency range of 360–680 Hz (with the bandwidth Δf1 = 320 Hz) are larger than 0.8, which exhibit the extraordinarily low-frequency sound absorption performance. Moreover, actual sound absorption coefficients are above 0.5 in the 350–1600 Hz range (with a bandwidth Δf2 = 1250 Hz), which achieve broadband sound absorption in the low–middle frequency range. According to various actual demands, the structural parameters can be adjusted flexibly to realize the customization of sound absorption bandwidth, which provides a novel way to design and improve acoustic metamaterials to reduce the noise with various frequency bands and has promising prospects of application in low-frequency sound absorption. [ABSTRACT FROM AUTHOR]

An acoustic metamaterial absorber of parallel–connection square Helmholtz resonators is proposed in this study, and its sound absorption coefficients are optimized to reduce the noise for the given conditions in the factory. A two–dimensional equivalent simulation model is built to obtain the initial value of parameters and a three–dimensional finite element model is constructed to simulate the sound absorption performance of the metamaterial cell, which aims to improve the research efficiency. The optimal parameters of metamaterial cells are obtained through the particle swarm optimization algorithm, and its effectiveness and accuracy are validated through preparing the experimental sample using 3D printing and measuring the sound absorption coefficient by the standing wave tube detection. The consistency between the experimental data and simulation data verifies feasibility of the proposed optimization method and usefulness of the developed acoustic metamaterial absorber, and the desired sound absorption performances for given conditions are achieved. The experimental results prove that parallel–connection square Helmholtz resonators can achieve an adjustable frequency spectrum for the low frequency noise control by parameter optimization, which is propitious to promote its application in reducing the noise in the factory. [ABSTRACT FROM AUTHOR]