Search

In this study, 0.04 wt % graphene oxide (GO) was added in different stages (before and after prepolymer formation, and during water addition) of the synthesis of waterborne polyurethane-urea dispersions (PUDs) prepared by using the acetone method. The structural, thermal, mechanical, viscoelastic, surface and adhesion properties of the polyurethane-ureas (PUUs) containing 0.04 wt % GO were studied. The addition of GO before and after prepolymer formation produced covalent bonds between the GO sheets and the NCO groups of the isocyanate, whereas the GO sheets were trapped between the polyurethane chains when added during water addition step. As a consequence, depending on the stage of the PUD synthesis in which GO was added, the degree of micro-phase separation between the hard and soft segments changed differently. The addition of GO before prepolymer formation changed more efficiently the polyurethane-urea structure, i.e., the covalently bonded GO sheets disturbed the interactions between the hard segments causing lower percentage of free urethane groups, higher crystallinity, lower storage modulus, higher yield stress and T-peel strength. The interactions between the GO sheets and the polymeric chains have been evidenced by plate-plate rheology, thermal gravimetric analysis and spectroscopy. On the other hand, physical interactions between GO and the polyurethane-urea chains were produced when GO was added in water during the synthesis, i.e., GO was acting as a nanofiller, which justified the improved mechanical properties and high lap-shear strength, but poor T-peel strength. [ABSTRACT FROM AUTHOR]

The paper examines the impact of aggregate shape on the compressive strength and thermal properties of concretes with silica fume based on two different aggregates: natural round gravel aggregate and crushed basalt aggregate. Compressive strength and thermal properties of individual concretes were determined during the first year of specimens curing. Additionally, porosity tests were conducted using mercury intrusion porosimetry and optical porosimetry. Mercury porosimetry tests showed that the use of silica fume led to a decrease in the content of pores of size smaller than 0.15 µm compared to the reference concretes without the addition of silica fume. However, tests carried out on crushed basalt-based concrete showed the presence of numerous additional pores with diameters ranging from 0.05 to 300 μm. In case of natural round gravel aggregate-based concrete, the addition of silica fume brought about an increase in its compressive strength. In turn, basalt-based concrete exhibited notably lower compressive strength values due to significantly higher porosity within the range of more than 70 μm. In basalt concrete, the obtained λ values are much lower than in concretes with normal gravel aggregate. In addition, the specific porosity structure had its impact on the process of drying of specimens of each group which occurred at a significantly faster rate in the basalt-based concrete. In conclusion, it can be stated that the use of crushed basalt aggregate causes a significant aeration of concrete, even despite the use of silica fume. As a result, the concrete based on crushed aggregate is characterized by a definitely lower compressive strength, but also better thermal insulation properties compared to analogous concrete made on natural round gravel aggregate. [ABSTRACT FROM AUTHOR]

The performance of vacuum insulation panels (VIPs) is strongly affected by several factors, such as panel thickness, design, quality of vacuum, and material type. In particular, the core materials inside VIPs significantly influence their overall performance. Despite their superior insulation performance, VIPs are limited in their widespread use as structural materials, because of their low material strength and the relatively expensive core materials. As an alternative core material that can compensate these limitations, foamed concrete, a type of lightweight concrete with very low density, can be used. In this study, two different types of foamed concrete were used as VIP core materials, with their effects on the thermal behavior of the VIPs having been evaluated using experimental and numerical methods. To confirm and generate numerical models for VIP analysis, micro-computed tomography (micro-CT) was utilized. The obtained results show that insulation effects increase effectively when panels with lightweight concrete are in a vacuum, and both foamed concrete types can be effectively used as VIP core materials. [ABSTRACT FROM AUTHOR]

Sustainable materials, such as vegetable oils, have become an effective alternative for liquid dielectrics in power transformers. However, currently available vegetable oils for transformer application are extracted from edible products with a negative impact on food supply. So, it is proposed in this study to develop cottonseed oil (CSO) as an electrical insulating material and cooling medium in transformers. This development is performed in two stages. The first stage is to treat CSO with tertiary butylhydroquinone (TBHQ) antioxidants in order to enhance its oxidation stability. The second and most important stage is to use the promising graphene oxide (GO) nanosheets to enhance the dielectric and thermal properties of such oil through synthesizing GO-based CSO nanofluids. Sodium dodecyl sulfate (SDS) surfactant was used as surfactant for GO nanosheets. The nanofluid synthesis process followed the two-step method. Proper characterization of GO nanosheets and prepared nanofluids was performed using various techniques to validate the structure of GO nanosheets and their stability into the prepared nanofluids. The considered weight percentages of GO nanosheets into CSO are 0.01, 0.02, 0.03 and 0.05. Dielectric and thermal properties were comprehensively evaluated. Through these evaluations, the proper weight percentage of GO nanosheets was adopted and the corresponding physical mechanisms were discussed. [ABSTRACT FROM AUTHOR]

Due to the brittle nature of poly(lactic acid) many attempts have been made to flexibilize this polyester for applications such as thin films and foils. However, due to complex phase behavior, many drawbacks for plasticizer and blend components are described. To overcome miscibility, post crystallization and migration issues a principle of click-chemistry was employed to change the molecular characteristics from external to internal plasticization by fixation of a plastisizing unit with help of a stereocomplex crystallization. Hydroxyl terminated polycaprolactone oligomers were used as a macroinitiator for the ring opening polymerization of d-lactide, resulting in blockcopolymers with plasticizing unit polycaprolactone and compatibilizing poly(d-lactic acid)-blocks. The generated block copolymers were blended with a poly(l-lactic acid)-matrix and formed so called stereocomplex crystals. In comparison to unbound polycaprolactone the polycaprolactone blocks show a lower migration tendency regarding a solution test in toluene. Besides that, trapping the plasticizing units via stereocomplex also improves the efficiency of the plasticizer. In comparison to polymer blends with the same amount of non-bonded polycaprolactone oligomers of the same molecular weight, block copolymers with poly(d-lactic acid) and polycaprolactone can shift the glass transition temperature to lower values. This effect can be explained by the modulated crystallization of the polycaprolactone-blocks trapped into the matrix, so that a higher effective amount can interact with the poly(l-lactic acid)-matrix. [ABSTRACT FROM AUTHOR]

Metakaolinite-based geopolymer binder was prepared at room temperature by mixing calcined claystone and potassium alkaline activator. Various granular inorganic fillers were added, amounting to 65 vol % to form geopolymer composites. The effect of four types of fillers (sand quartz, chamotte, cordierite, and corundum) on the thermo-mechanical properties of metakaolinite-based geopolymer composites were investigated. The samples were also examined by an X-ray diffraction method to determine their phase composition. The pore size distributions were determined by a mercury intrusion porosimeter. The XRD revealed the crystallization of new phase (leucite) after thermal exposure at 1000 °C and higher. Geopolymer binders had low mechanical properties (flexural strength 2.5 MPa and compressive strength 45 MPa) and poor thermo-mechanical properties (especially high shrinkage—total shrinkage 9%) compared to geopolymer composites (flexural strength up to 13.8 MPa, compressive strength up to 95 MPa and total shrinkage up to 1%). The addition of fillers reduced the shrinkage of geopolymers and improved their mechanical properties. The results have shown that the compressive strength tested in situ and after exposure to high temperature are in conflict. Geopolymer composites with the addition of chamotte had the best mechanical properties before and after thermal exposure (compressive strength up to 95 MPa). The average pore size diameters increased with the increasing temperature (from 10 nm to approx. 700 nm). The fillers addition decreased the pore volume (from 250 mm3/g to approx. 100 mm3/g). [ABSTRACT FROM AUTHOR]

Electrospraying is considered to be a green, high-efficiency method for synthesizing phase change microcapsules (mPCMs) for possible applications in the fields of energy storage and thermal regulation. In this study, a coaxial nozzle was used to prepare n-hexadecane/polycaprolactone (PCL) microparticles. The objectives of this study were to investigate the influence of working parameters and solutions on morphology, particle size, thermal properties and encapsulation efficiency. Thus, three theoretical loading contents in n-hexadecane (30%, 50% and 70% w/w) and two concentrations of PCL (5 and 10% w/v) were used. The structures, morphologies and thermal properties of mPCMs were characterized by optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA). Spherical microcapsules with a mean diameter of 10–20 µm were prepared. The increased concentration of n-hexadecane and PCL resulted in a change in the particle size distribution from a poly-disperse to monodisperse size distribution and in a change in the surface state from porous to non-porous. In addition, higher encapsulation efficiency (96%) and loading content (67%) were achieved by the coaxial nozzle using the high core-shell ratio (70/30) and 10% w/v of PCL. The latent heat of the mPCMs reached about 134 J.g−1. In addition, it was also observed that the thermal stability was improved by using a coaxial system rather than a single nozzle. [ABSTRACT FROM AUTHOR]

We report the synthesis and thermoelectric transport properties of As-doped layered pnictogen oxyselenides NdO0.8F0.2Sb1−xAsxSe2 (x ≤ 0.6), which are predicted to show high-performance thermoelectric properties based on first-principles calculation. The crystal structure of these compounds belongs to the tetragonal P4/nmm space group (No. 129) at room temperature. The lattice parameter c decreases with increasing x, while a remains almost unchanged among the samples. Despite isovalent substitution of As for Sb, electrical resistivity significantly rises with increasing x. Very low thermal conductivity of less than 0.8 Wm−1K−1 is observed at temperatures between 300 and 673 K for all the examined samples. For As-doped samples, the thermal conductivity further decreases above 600 K. Temperature-dependent synchrotron X-ray diffraction indicates that an anomaly also occurs in the c-axis length at around 600 K, which may relate to the thermal transport properties. [ABSTRACT FROM AUTHOR]

Negative thermal expansion is an interesting and appealing phenomenon for various scientific and engineering applications, while rarely occurring in natural materials. Here, using a universal antichiral metamaterial model with bimetal beams or strips, a generic theory has been developed to predict magnitude of the negative thermal expansion effect from model parameters. Thermal expansivity of the metamaterial is written as an explicit function of temperature and only three design parameters: relative node size, chirality angle, and a bimetal constant. Experimental measurements follow theoretical predictions well, where thermal expansivity in the range of negative 0.0006–0.0041 °C−1 has been seen. [ABSTRACT FROM AUTHOR]

Agricultural residues are major potential resources for biomass and for material production. In this work, rice straw residues were used to isolate cellulose nanofibers of different degree of oxidation. Firstly, bleached rice fibers were produced from the rice straw residues following chemical extraction and bleaching processes. Oxidation of rice fibers mediated by radical 2,2,6,6-tetramethylpiperidine 1-oxyl (TEMPO) at pH 10 was then applied to extract rice cellulose nanofibers, with diameters of 3–11 nm from morphological analysis. The strengthening capacity of rice nanofibers was tested by casting nanocomposite films with poly(vinyl alcohol) polymer. The same formulations with eucalyptus nanofibers were produced as comparison. Their thermal and mechanical performance was evaluated using thermogravimetry, differential scanning calorimetry, dynamic mechanical analysis and tensile testing. The glass transition of nanocomposites was shifted to higher temperatures with respect to the pure polymer by the addition of rice cellulose nanofibers. Rice nanofibers also acted as a nucleating agent for the polymer matrix. More flexible eucalyptus nanofibers did not show these two phenomena on the matrix. Instead, both types of nanofibers gave similar stiffening (as Young's modulus) to the matrix reinforced up to 5 wt.%. The ultimate tensile strength of nanocomposite films revealed significant enhancing capacity for rice nanofibers, although this effect was somehow higher for eucalyptus nanofibers. [ABSTRACT FROM AUTHOR]

Increasing concerns about climate change and global warming bring about technical steps for the development of several energy-efficient technologies. Since the building sector is one of the largest energy users for cooling and heating necessities, the incorporation of a proper energy-efficient material into the building envelopes could be an interesting solution for saving energy. Phase change material (PCM)-based thermal energy storage (TES) seems suitable to provide efficient energy redistribution. This is possible because the PCM is able to store and release its latent heat during the phase change processes that occurs according to the environmental temperature. The purpose of this paper was the characterization of the thermal properties of a composite PCM (i.e., Lecce stone/poly-ethylene glycol, previously developed) incorporated into mortar compositions based on different binders (i.e., hydraulic lime and cement). The study was carried out using an experimental set up through which it was possible to simulate the different seasons of the years. It was observed that the addition of PCM in mortars leads to a decrease of the maximum temperatures and increase of the minimum temperatures. Furthermore, the results shown a reduction of the heating and cooling needs, thus confirming the capability of this material to save energy. [ABSTRACT FROM AUTHOR]

The use of (bio)degradable polymers, especially in medical applications, requires a proper understanding of their properties and behavior in various environments. Structural elements made of such polymers may be exposed to changing environmental conditions, which may cause defects. That is why it is so important to determine the effect of processing conditions on polymer properties and also their subsequent behavior during degradation. This paper presents original research on a specimen's damage during 70 days of hydrolytic degradation. During a standard hydrolytic degradation study of polylactide and polylactide/polyhydroxyalkanoate dumbbell-shaped specimens obtained by 3D printing with two different processing build directions, exhibited unexpected shrinkage phenomena in the last degradation series, representing approximately 50% of the length of the specimens irrespective of the printing direction. Therefore, the continuation of previous ex-ante research of advanced polymer materials is presented to identify any possible defects before they arise and to minimize the potential failures of novel polymer products during their use and also during degradation. Studies on the impact of a specific processing method, i.e., processing parameters and conditions, on the properties expressed in molar mass and thermal properties changes of specimens obtained by three-dimensional printing from polyester-based filaments, and in particular on the occurrence of unexpected shrinkage phenomena after post-processing heat treatment, are presented. [ABSTRACT FROM AUTHOR]

In this study, natural deposits of Kankara kaolin clay were collected and investigated in order to determine physical, microstructural, thermal, and firing properties and assess clay's suitability as starting material for various ceramic applications. Chemical analysis of the clay was performed using XRF. Mineralogical analysis and thermal analysis of the clay were conducted using XRD and thermogravimetric thermal analysis (TGA)/differential thermal analysis (DTA), respectively. In order to assess its ceramic behavior, the clay was fired at 900–1200 °C. Maturation characteristics of fired ceramics were assessed by measuring bulk density, apparent porosity, and shrinkage. It was found that main oxides in the clay are alumina, silica, and potassium oxide, while other oxides are present in trace quantities. Kaolinite, quartz, and illite are the phases found from the XRD results, while mullite ceramic phase formed at firing temperature above 1100 °C. Maturation tests showed that ceramic properties such as bulk density and shrinkage increase with temperature, while apparent porosity decreases with temperature. The results presented in this study prove that the clay is an appropriate material for producing traditional ceramics. [ABSTRACT FROM AUTHOR]

Surfactant tolerance in the presence of mono and divalent reservoir ions, as well as the solubility of surfactant in high salinity and low salinity brine, are the two major requirements for any surfactant that is subjected to oilfield application. Herein, six poly(ethylene oxide) zwitterionic surfactants having different ionic headgroups and hydrophobic tail were synthesized for oilfield applications. They were characterized by various instrumental techniques (Fourier-transform infrared spectroscopy (FTIR), matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-ToF-MS), Nuclear Magnetic Resonance (NMR)) and the combination of these techniques allowed for us to deduce the structure. All of the surfactants revealed prominent solubility in high salinity and low salinity brine due to the presence of ethoxy units between the aromatic ring and amide group. The surfactant samples were oven aged for 90 days at reservoir temperature and a clear solution implies their excellent aqueous stability. Rendering to thermal gravimetric results, decomposition of surfactants was found to occur around 300 °C, which is higher than the reservoir temperature (≥90 °C). It was observed that the hydrophilic headgroup has no significant impact on the critical micelle concentration and other surface properties. However, the hydrophobic tail bearing benzene ring significantly alters the critical micelle concentration and other surface properties. [ABSTRACT FROM AUTHOR]

In this work, rigid polyurethane (PUR) foams were prepared by incorporating 2 wt% of eucalyptus fibers. The eucalyptus fibers were surface-modified by maleic anhydride, alkali, and silane (triphenylsilanol) treatment. The impact of the modified eucalyptus fibers on the mechanical, thermal, and fire performances of polyurethane foams was analyzed. It was observed that the addition of eucalyptus fibers showed improved mechanical and thermal properties and the best properties were shown by silane-treated fibers with a compressive strength of 312 kPa and a flexural strength of 432 kPa. Moreover, the thermal stability values showed the lowest decline for polyurethane foams modified with the silane-treated fibers, due to the better thermal stability of such modified fibers. Furthermore, the flame resistance of polyurethane foams modified with the silane-treated fibers was also the best among the studied composites. A cone calorimetry test showed a decrease in the peak of heat release from 245 to 110 kW∙m−2 by the incorporation of silane-treated fibers. Furthermore, total heat release and total smoke release were also found to decrease remarkably upon the incorporation of silane-treated fibers. The value of limiting oxygen index was increased from 20.2% to 22.1%. Char residue was also found to be increased from 24.4% to 28.3%. It can be concluded that the application of chemically modified eucalyptus fibers has great potential as an additive to incorporate good mechanical, thermal, and fire properties in rigid polyurethane foams. [ABSTRACT FROM AUTHOR]

Alumina/polyurethane composites were prepared via in situ polymerization and used as thermal interface materials (TIMs). The surface of alumina particles was modified using polydopamine (PDA) and then evaluated via Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG), and Raman spectroscopy (Raman). Scanning electron microscope (SEM) images showed that PDA-Al2O3 has better dispersion in a polyurethane (PU) matrix than Al2O3. Compared with pure PU, the 30 wt% PDA-Al2O3/PU had 95% more Young's modulus, 128% more tensile strength, and 76% more elongation at break than the pure PU. Dynamic mechanical analysis (DMA) results showed that the storage modulus of the 30 wt% PDA-Al2O3/PU composite improved, and the glass transition temperature (Tg) shifted to higher temperatures. The thermal conductivity of the 30 wt% PDA-Al2O3/PU composite increased by 138%. Therefore, the results showed that the prepared PDA-coated alumina can simultaneously improve both the mechanical properties and thermal conductivity of PU. [ABSTRACT FROM AUTHOR]

This paper performed a detailed study on the fundamental properties and thermal conductivity of autoclaved aerated concrete (AAC) self-insulation block, and the mechanical properties and heat transfer resistance of the AAC self-insulation block masonry. Different kinds of joints and the plastering surface were used to build the masonry specimens. The distinctive feature of the blocks and mortars is the lower thermal conductivity with expected strength. Compared to those with larger thickness of insulation mortar joints, the masonry with thin-layer mortar joints had better compressive performance and lower shear strength. The compressive strength of masonry was related with the block and mortar strengths, the shear strength of masonry along mortar joints was related with the mortar strength. The stress–strain relationship of masonry in compression could be predicted by the similar expression of conventional block masonry. The tested heat transfer coefficient of AAC self-insulation block masonry with thickness of 250 mm without plastering surfaces was (0.558 ± 0.003) W/(m2·K). With the plastering surfaces, the heat transfer coefficient reduced by 4.4% to 8.9%. Good agreements in values of heat transfer coefficient existed by using the test, theoretical computation and ANSYS (ANSYS Inc. Canonsburg, PA, USA) analytical methods. Based on the extensibility analyses, the heat transfer coefficients of AAC self-insultation block masonry with different thickness are proposed. The best thickness is proposed for the outer walls of residential buildings in different cold zone to meet the design requirement of energy conservation. [ABSTRACT FROM AUTHOR]

Thermoplastic elastomer blends based on natural rubber (NR) and ethylene-vinyl acetate copolymer (EVA) with different weight ratios (30, 40, 50, 60 and 70 parts per hundred rubber (phr) of NR) and 10, 20 and 30 phr of straw were prepared and characterized. Current environmental problems were the motivation to produce this type of system, namely: the need to replace plastics at least partly with natural materials; increasing the amount of renewable raw materials and managing excess straw production. When using this bioadditive in traditional materials, the high processing temperature can be problematic, leading to the degradation of straw fibers. The solution can be polymer mixtures that are prepared at significantly lower temperatures. Scanning electron microscope (SEM) imaging was used to investigate the particle size of fibers and phase morphology of composites. Moreover, determination of the thermal properties of the filler and composites showed that the processing temperature used in the production of NR/EVA blends reduces the risk of degradation of the natural filler. Differential scanning calorimetry (DSC) was used to determine the thermal behavior of the filled composites. Finally, rheological tests of materials allow the determination of optimal processing parameters and properties of materials in dynamic conditions. The proposed blends exhibit elastic properties, and due to the lack of chemical cross-linking they can be processed and recycled like thermoplastics. In addition, they offset the disadvantages and combine the advantages of natural rubber and ethylene-vinyl acetate copolymer in the form of thermoplastic elastomeric biocomposites. [ABSTRACT FROM AUTHOR]

This study analyses the deterioration of mechanical properties in lightweight concrete after exposure to room temperature (20 °C) and high temperature, i.e., up to 1000 °C, including changes in visual appearance, loss of mass, and compressive strength. All-lightweight shale ceramsite aggregate concrete (ALWAC) and semi-lightweight shale ceramsite aggregate concrete (SLWAC) are prepared using an absolute volume method to analyse the relationships between relative ultrasonic pulse velocity, loss rate of compressive strength, damage degree, and temperature levels. Our results show that, under high temperature, the lightweight aggregate ceramsite concrete performs better compared to normal concrete. After exposure to 1000 °C, the ALWAC shows a strength loss of no more than 80%, while the normal concrete loses its bearing capacity, with a similar strength loss as the SLWAC. Furthermore, the relative ultrasonic pulse velocity and damage degree are used to evaluate the effects of high temperature on the concretes, including the voids and cracks on the surface and inside of the specimens, which induces the deterioration of mechanical properties and contributes to the thermal decomposition of the cementing system and the loss of cohesion at the aggregate interface. Based on internal structure analyses, the results from this study confirm that the lightweight aggregate concrete shows a high residual compressive strength after exposure to the high temperature. [ABSTRACT FROM AUTHOR]

The effect of the microstructure of solder joints on the thermal properties of power LEDs is investigated. Solder joints were prepared with different solder pastes, namely 99Sn0.3Ag0.7Cu (as reference solder) and reinforced 99Sn0.3Ag0.7Cu–TiO2 (composite solder). TiO2 ceramic was used at 1 wt.% and with two different primary particle sizes, which were 20 nm (nano) and 200 nm (submicron). The thermal resistance, the electric thermal resistance, and the luminous efficiency of the power LED assemblies were measured. Furthermore, the microstructure of the different solder joints was analyzed on the basis of cross-sections using scanning electron and optical microscopy. It was found that the addition of submicron TiO2 decreased the thermal and electric thermal resistances of the light sources by 20% and 16%, respectively, and it slightly increased the luminous efficiency. Microstructural evaluations showed that the TiO2 particles were incorporated at the Sn grain boundaries and at the interface of the intermetallic layer and the solder bulk. This caused considerable refinement of the Sn grain structure. The precipitated TiO2 particles at the bottom of the solder joint changed the thermodynamics of Cu6Sn5 formation and enhanced the spalling of intermetallic grain to solder bulk, which resulted in a general decrease in the thickness of the intermetallic layer. These phenomena improved the heat paths in the composite solder joints, and resulted in better thermal and electrical properties of power LED assemblies. However, the TiO2 nanoparticles could also cause considerable local IMC (Intermetallic Compounds) growth, which could inhibit thermal and electrical improvements. [ABSTRACT FROM AUTHOR]

The thermal conductivity of concrete is a key factor for efficient energy consumption in concrete buildings because thermal conductivity plays a significant role in heat transfer through concrete walls. This study investigated the effects of replacing fine aggregates with coal bottom ash (CBA) and the influence of curing age on the thermal properties of high-strength concrete with a compressive strength exceeding 60 MPa. The different CBA aggregate contents included 25%, 50%, 75%, and 100%, and different curing ages included 28 and 56 days. For concrete containing CBA fine aggregate, the thermal and mechanical properties, including the unit weight, thermal conductivity, compressive strength, and ultrasonic velocity, were measured. The experimental results reveal that the unit weight and thermal conductivity of the CBA concrete were highly dependent on the CBA content. The unit weight, thermal conductivity, and compressive strength of the concrete decreased as the CBA content increased. Relationships between the thermal conductivity and the unit weight, thermal conductivity and compressive strength of the CBA concrete were proposed in the form of exponential functions. The equations proposed in this study provided predictions that were in good agreement with the test results. In addition, the test results show that there was an approximately linear relationship between the thermal conductivity and ultrasonic velocity of the CBA concrete. [ABSTRACT FROM AUTHOR]

This paper presents the development of metallic thermoresistive thin film, providing an innovative solution to dynamically control the temperature during the injection molding process of polymeric parts. The general idea was to tailor the signal response of the nitrogen- and oxygen-doped titanium-copper thin film (TiCu(N,O))-based transducers, in order to optimize their use in temperature sensor devices. The results reveal that the nitrogen or oxygen doping level has an evident effect on the thermoresistive response of TiCu(N,O) films. The temperature coefficient of resistance values reached 2.29 × 10−2 °C−1, which was almost six times higher than the traditional platinum-based sensors. In order to demonstrate the sensing capabilities of thin films, a proof-of-concept experiment was carried out, integrating the developed TiCu(N,O) films with the best response in an injection steel mold, connected to a data acquisition system. These novel sensor inserts proved to be sensitive to the temperature evolution during the injection process, directly in contact with the polymer melt in the mold, demonstrating their possible use in real operation devices where temperature profiles are a major parameter, such as the injection molding process of polymeric parts. [ABSTRACT FROM AUTHOR]

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites' performance, which should be considered beneficial when engineering PE/metal composites. [ABSTRACT FROM AUTHOR]

Tensile tests on two kinds of electroplated copper foils with twins before and after annealing were performed. One electroplating parameter results in a microstructure of <110>-oriented microtwinned Cu (mt-Cu), and the other is <111>-oriented nanotwinned Cu (nt-Cu). The latter shows higher thermal stability than the former after annealing. Though the toughness for the two as-plated foils are quite close, the toughness for the <111> oriented nt-Cu increased from 34 to 74 MJ/m3 after annealing at 250 °C for 3 h. In comparison, the toughness of the <110>-oriented mt-Cu remained almost the same after annealing. [ABSTRACT FROM AUTHOR]

The continuous and rapid evolution in the field of computing, and in particular in the field of storage devices, has led to the obsolescence of optical discs in favour of mass storage devices. In that sense, a large number of CDs and DVDs become obsolete each day in the world. In trying to create a recovery solution for those pieces, research in which polycarbonate (PC) waste from recycled discs have been used to develop new gypsum coating materials and products has been conducted. In a previous study, the physical and mechanical properties of new gypsum plasters, with PC waste as aggregate, were studied. Following that study, this article aims at creating new gypsum plaster false ceiling plates, using CD and DVD residues in different scenarios: as crushed aggregate in the gypsum matrix, as full reinforcement pieces of the plates and as a combination of both. The mechanical behaviour and the thermal conductivity of the new pieces have been analysed in this paper. The results showed an important improvement in the mechanical and thermal properties of the plates when the PC waste was used in many scenarios. [ABSTRACT FROM AUTHOR]

Esters present several advantages when compared to traditional materials used for thermal energy storage, amongst which are better sustainability and greater chemical stability. However, at present, their thermal properties remain mostly unknown or not well documented. In this study, 12 diesters from four dicarboxylic acids (oxalic, succinic, suberic, sebacic) and three alcohols (methanol, 1-pentanol, 1-decanol) have been assessed as bio-based phase change materials for thermal energy storage. All diesters have been synthesized via Fischer esterification to high purities, and their chemical structures, as well as thermal properties, have been fully characterized. The diesters investigated show phase change transitions in a low–mid temperature range between −32 and 46 °C with maximum enthalpies of 172 J/g and show higher degrees of supercooling compared to fatty monoesters. Similarly to other esters classes, some trends correlating the chemical structures to the thermal properties were identified, which would allow for the development of property prediction tools. [ABSTRACT FROM AUTHOR]

This article presents a novel potential bio-based rejuvenator derived from waste pig fat (WPF) for use in recycled asphalt applications. To achieve this purpose, the impact of different doses waste pig fat (e.g., 0, 3, 6, and 9 wt.% WPF) on the reclaimed asphalt pavement binder (RAP-B) performance is investigated. The unmodified and WPF-modified asphalts are characterized by means of Fourier-transform infrared spectroscopy (FT-IR), thin-layer chromatography–flame ionization detection (TLC-FID), scanning electron microscopy (SEM), atomic force microscopy (AFM), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Physico-rheological properties of asphalt blends are assessed through Brookfield viscometer, softening point, penetration, and dynamic shear rheometer (DSR) tests. TLC-FID data highlighted that incremental WPF addition into RAP-B restored its original balance maltenes-to-asphaltenes ratio; finding which was supported by FT-IR analysis. SEM disclosed that WPF has a great compatibility with the aged asphalt. AFM observations showed that grease treatment induced a decline in surface roughness (i.e., bee structures) and a rise in friction force (i.e., para-phase dimension) of RAP binder. TGA/DSC studies revealed that the bio-modifier not only possesses an excellent thermal stability but also can substantially enhance the binder low-temperature performance. Empirical and DSR tests demonstrated that WPF improved the low-temperature performance grade of RAP-B, reduced its mixing and compaction temperatures, and noticeably boosted its fatigue cracking resistance. The rejuvenation of aged asphalt employing WPF is feasible and can be an ideal approach to recycle both of RAP and waste pig fats. [ABSTRACT FROM AUTHOR]

In this work Macadamia nutshell (MS) was used as filler in fused deposition modeling (FDM) of Poly (lactic acid) (PLA) composites filaments. Composites containing MS both treated and untreated with alkali and silane were investigated by means of Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD), Thermogravimetry (TG), scanning electron microscopy (SEM). The results showed that the treated MS composites had better thermal stability. Furthermore, compression tests were carried out. The PLA with 10 wt% treated MS composite was found possessing the best mechanical properties which was almost equivalent to that of the pure PLA. Finally, porous scaffolds of PLA/10 wt% treated MS were fabricated. The scaffolds exhibited various porosities in range of 30–65%, interconnected holes in size of 0.3–0.5 mm, micro pores with dimension of 0.1–1 μm and 37.92–244.46 MPa of elastic modulus. Those values indicated that the FDM of PLA/MS composites have the potential to be used as weight lighter and structural parts. [ABSTRACT FROM AUTHOR]

A uniform, monodispersed superfine cuprous oxide (Cu2O) sphere with a mean diameter of 850 nm has been synthesized by solution reduction. The study reported the synthesis and thermal properties of Cu2O/PP composites for the first time. The surface modification of the superfine Cu2O sphere was carried out by using a silane coupling agent KH-570. Fourier-transform infrared (FTIR) spectroscopy and the thermogravimetric analysis (TGA) curve revealed that the Cu2O had been successfully modified by silane coupling agent KH570. The scanning electron microscope (SEM) shows that the modified Cu2O can be uniformly dispersed in the polypropylene (PP) matrix, because through surface modification, there are some active functional groups on its surface, such as the ester group, which improves its compatibility with the PP matrix. The thermal stability of Cu2O/PP composites was improved by adding a small amount of Cu2O (1 wt % of PP). Therefore, based on the potential bacteriostasis of cuprous oxide, the low cost of PP and the results of this study, it is predicted that Cu2O/PP composites can be used in infant preparation (such as milk bottles) with low cost and good thermal stability in the near future. [ABSTRACT FROM AUTHOR]

In this study, effects of two different types of porous alumina nanoparticles have been incorporated into high-density polyethylene (HDPE) to study their impact on the properties of the HDPE composite. The dispersion of fillers in the HDPE matrix was evaluated by scanning electron microscopy (SEM). Differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA) integrated with Fourier transform infrared spectroscopy (FTIR) were applied to investigate the calorimetric behavior and thermal stability and to analyze the polymer decomposition, respectively. The dielectric properties were determined by a broadband dielectric spectroscopy. The effect of filler loading on the tensile properties and melt flow index was also examined. A homogenous distribution of the fillers was observed at low loading of alumina particles (below 5 wt. %). However, agglomerates of sub-micro size were formed extensively on samples with high loading of fillers (above 7 wt. %). A significant improvement of the thermo-oxidation stability of the composite was observed. The permittivity values of the prepared composites also increased with the addition of the fillers. The incorporation of fillers also increased the electrical conductivity values of the prepared composites at high frequencies. [ABSTRACT FROM AUTHOR]

A 9,10-dihydro-9-oxa-10-phosphaphenanthrene 10-oxide (DOPO) acrylate, (6-oxidodibenzo [c,e][1,2] oxaphosphinin-6-yl) methyl acrylate (DOPOAA), has been prepared. Copolymers of styrene (St) and DOPOAA were prepared by emulsion polymerization. The chemical structures of copolymers containing levels of DOPOAA were verified using Fourier transform infrared (FT-IR) spectroscopy and 1H nuclear magnetic resonance (1H-NMR) spectroscopy. The thermal properties and flame-retardant behaviors of DOPO-containing monomers and copolymers were observed using thermogravimetric analysis and micro calorimetry tests. From thermogravimetric analysis (TGA), it was found out that the T5% for decomposition of the copolymer was lower than that of polystyrene (PS), but the residue at 700 °C was higher than that of PS. The results from micro calorimetry (MCC) tests indicated that the rate for the heat release of the copolymer combustion was lower than that for PS. The limiting oxygen index (LOI) for combustion of the copolymer rose with increasing levels of DOPOAA. These data indicate that copolymerization of the phosphorus-containing flame-retardant monomer, DOPOAA, into a PS segment can effectively improve the thermal stability and flame retardancy of the copolymer. [ABSTRACT FROM AUTHOR]

SiC is a material with excellent mechanical and thermal properties but with a high production cost. Obtaining SiC by reactive infiltration is an attractive method with a much lower cost than the traditional sintering process. However, the reactive infiltration process presents a serious problem, which is the high residual silicon content, which decreases its applicability. The replacement of silicon with silicides is a widely used alternative. The present investigation shows the good mechanical properties of the SiC-IrSi3 composite material obtained by reactive infiltration of SiC-C preforms with Ir–Si alloys. The thermomechanical analysis shows a high compatibility of silicide with SiC. The presence of the silicide shows a substantial improvement against the oxidation of the SiC-Si composites. [ABSTRACT FROM AUTHOR]

Acrylonitrile butadiene styrene (ABS) is the oldest fused filament fabrication (FFF) material that shows low stability to thermal aging due to hydrogen abstraction of the butadiene monomer. A novel blend of ABS, polypropylene (PP), and polyethylene graft maleic anhydride (PE-g-MAH) is presented for FFF. ANOVA was used to analyze the effects of three variables (bed temperature, printing temperature, and aging interval) on tensile properties of the specimens made on a custom-built pellet printer. The compression and flexure properties were also investigated for the highest thermal combinations. The blend showed high thermal stability with enhanced strength despite three days of aging, as well as high bed and printing temperatures. Fourier-transform infrared spectroscopy (FTIR) provided significant chemical interactions. Differential scanning calorimetry (DSC) confirmed the thermal stability with enhanced enthalpy of glass transition and melting. Thermogravimetric analysis (TGA) also revealed high temperatures for onset and 50% mass degradation. Signs of chemical grafting and physical interlocking in scanning electron microscopy (SEM) also explained the thermo-mechanical stability of the blend. [ABSTRACT FROM AUTHOR]

Doping is known as an effective way to modify both electrical and thermal transport properties of thermoelectric alloys to enhance their energy conversion efficiency. In this project, we report the effect of Pd doping on the electrical and thermal properties of n-type Cu0.008Bi2Te2.7Se0.3 alloys. Pd doping was found to increase the electrical conductivity along with the electron carrier concentration. As a result, the effective mass and power factors also increased upon the Pd doping. While the bipolar thermal conductivity was reduced with the Pd doping due to the increased carrier concentration, the contribution of Pd to point defect phonon scattering on the lattice thermal conductivity was found to be very small. Consequently, Pd doping resulted in an enhanced thermoelectric figure of merit, zT, at a high temperature, due to the enhanced power factor and the reduced bipolar thermal conductivity. [ABSTRACT FROM AUTHOR]

This research aims at clarifying the influence of the granulometry of expanded perlite, on the thermal conductivity, structural strength, density, and water absorption of lightweight mortars. Three original perlite gradations have been obtained and three pairs of twin test mortars have been tested with those gradations. SEM tests have also been run to clarify the interaction, at a microscopic level, between the expanded perlite and the cement grouting. The results indicate that the mere manipulation of the granulometry may have a considerable and very beneficial effect on the mixture's properties, such as thermal conductivity and water absorption. [ABSTRACT FROM AUTHOR]

In this investigation, ZrxY2−xVxMo3−xO12 (0 ≤ x ≤ 1.4) is developed and the effects of the substitutions of Zr4+/V5+ for Y3+/Mo6+ in Y2Mo3O12 on the hygroscopicity and thermal expansion property are investigated. For the smaller substitution content (x ≤ 0.5), their crystal structures remain orthorhombic, while there is crystal water still in the lattice. The linear coefficients of thermal expansions (CTEs), for x = 0.1, 0.3, 0.5, and 0.7, are about −4.30 × 10−6, −0.97 × 10−6, 0.85 × 10−6, and 0.77 × 10−6 K−1, respectively, from 476 to 773 K, which means that the linear CTE could be changed linearly with the substitution content of Zr4+/V5+ for Y3+/Mo6+ in Y2Mo3O12. As long as the substitution content reaches x = 1.3/1.4, almost no hygroscopicity and low thermal expansion from room temperature are obtained and are discussed in relation to the crystal structure and microstructure. [ABSTRACT FROM AUTHOR]

In this research work, graphene nanoplatelets (GNP) were selected as alternative reinforcing nanofillers to enhance the properties of polypropylene (PP) using different compatibilizers called polypropylene grafted maleic anhydride (PP-g-MA) and ethylene-octene elastomer grafted maleic anhydride (POE-g-MA). A twin screw extruder was used to compound PP, GNP, and either the PP-g-MA or POE-g-MA compatibilizer. The effect of GNP loading on mechanical and thermal properties of neat PP was investigated. Furthermore, the influence and performance of different compatibilizers on the final properties, such as mechanical and thermal, were discussed and reported. Tensile, flexural, impact, melting temperature, crystallization temperature, and thermal stability were evaluated by using a universal testing system, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). For mechanical properties, it was found that increasing GNP content from 1 wt.% to 5 wt.% increased tensile strength of the neat PP up to 4 MPa. The influence of compatibilizers on the mechanical properties had been discussed and reported. For instance, the addition of PP-g-MA compatibilizer improved tensile strength of neat PP with GNP loading. However, the addition of compatibilizer POE-g-MA slightly decreased the tensile strength of neat PP. A similar trend of behavior was observed for flexural strength. For thermal properties, it was found that both GNP loading and compatibilizers have no significant influence on both crystallization and melting temperature of neat PP. For thermal stability, however, it was found that increasing the GNP loading had a significant influence on improving the thermal behavior of neat PP. Furthermore, the addition of compatibilizers into the PP/GNP nanocomposite had slightly improved the thermal stability of neat PP. [ABSTRACT FROM AUTHOR]

Prediction of hydration temperature and induced stresses in mass foundation slabs, due to the hydration effects is a difficult task. The complexity of this issue is compounded by transient and non-linear thermo-mechanical phenomena as well by a significant number of contributing technological and material factors that affect the early-age volume changes. This is a probable reason for the limited number of simple analytical methods allowing for the estimation of these effects. This work presents a new proposal in the discussed field. The submitted analytical method for determining the hydration temperature rise, its differentials at a cross-section and induced thermal stresses in mass concrete foundation slabs considers the majority of important technological and material factors, such as the initial temperature of the concrete, the ambient temperature, the thermal properties of the concrete and the heat exchange conditions on the slab surfaces. In stress analysis, both self-balanced and restraint stresses are calculated. Finally, the method is validated in FE analysis conducted for the slabs with various heights and made of different types of cements, as well as by the thermal measurements from the construction site. Due to the limited number of methods allowing for the analytical estimation of the early age thermo-mechanical effects in slabs, this new proposal can be useful in the assessment of these effects. [ABSTRACT FROM AUTHOR]

Foamed concrete materials based on sulpoaluminate cement were prepared by the chemical foaming method. The effects of water–cement ratio, foaming agent, and foaming stabilizer on the mechanical and thermal properties of foamed concrete were studied. Meanwhile, a portion of cement was replaced with foamed phenolic particles to further optimize the performance of foamed concrete; the results show that when the water–cement ratio was 0.53, the foaming agent content was 5%, the foam stabilizer was 1%, and the substitution of phenolic particles was 20%, the performance indexes of foamed concrete were the best. Methods, describing briefly the main methods or treatments applied: dry density was 278.4 kg/m3, water absorption was 19.9%, compressive strength was 3.01 MPa, and thermal conductivity was 0.072 W/(m·K). By the pore structure analysis of the foamed concrete suing Micro-CT, it was found that when the replacement amount of phenolic particles was 20%, the pore size of foamed concrete was relatively uniform, the minimum D90 was 225 μm respectively. The combination of organic and inorganic matrix and optimized pore structure improved the performance of foamed concrete. [ABSTRACT FROM AUTHOR]

Multiferroic materials are widely used in microelectronics because they are sensitive to elastic, magnetic, and electric fields and there is an intrinsic coupling between them. In particular, transition metal-doped BaTiO3 is considered as a viable multiferroic because of the simultaneous presence of ferroelectricity and magnetism. In this work, we study the electrical and thermal properties of Mn-doped BaTiO3 ceramics that can be used for multicaloric applications. We found that Mn doping leads to the broadening and shifting of the phase transition accompanied with simultaneous decrease of latent heat and entropy. Mn doping causes a decrease in the bulk resistivity while contact resistance remains intact. Doped ceramics can withstand high electric fields (up to 40 kV/cm) and exhibit linear I-V characteristics followed by the Schottky limited current in contrast to earlier observations. As such, these ceramics are promising for multicaloric applications. [ABSTRACT FROM AUTHOR]

Polylactic acid-based materials have gained great interest within the scientific community due to their biodegradability, good performance, and suitability for a number of applications. Therefore, this Special Issue "Poly(lactic acid) Composites" is proposed to cover the important advances in poly (lactic acid) composites, ranging from their design, fabrication, and material properties to the potential applications of these materials. Therefore, we believe that the present Issue can convey beneficial information to scientists and engineers in numerous fields, including polymer science and biomedical engineering. [ABSTRACT FROM AUTHOR]

AlN nanoparticles were added into commercial high-temperature-vulcanized silicon rubber composites, which were designed for high-voltage outdoor insulator applications. The composites were systematically studied with respect to their mechanical, electrical, and thermal properties. The thermal conductivity was found to increase greatly (>100%) even at low fractions of the AlN fillers. The electrical breakdown strength of the composites was not considerably affected by the AlN filler, while the dielectric constants and dielectric loss were found to be increased with AlN filler ratios. At higher doping levels above 5 wt% (~2.5 vol%), electrical tracking performance was improved. The AlN filler increased the tensile strength as well as the hardness of the composites, and decreased their flexibility. The hydrophobic properties of the composites were also studied through the measurements of temperature-dependent contact angle. It was shown that at a doping level of 1 wt%, a maximum contact angle was observed around 108°. Theoretical models were used to explain and understand the measurement results. Our results show that the AlN nanofillers are helpful in improving the overall performances of silicon rubber composite insulators. [ABSTRACT FROM AUTHOR]

In this paper, we consider several designs for nitride-based vertical-cavity surface-emitting lasers (VCSELs) with a top semiconductor-metal subwavelength grating (SMSG) as the facet mirror. The constructions of the bottom distributed Bragg reflectors (DBRs) used in the VCSEL designs were inspired by devices demonstrated recently by several research groups. A multiparameter numerical analysis was performed, based on self-consistent thermal and electrical simulations. The results show that, in the case of small aperture VCSEL designs, dielectric-based DBRs with metallic or GaN channels enable equally efficient heat dissipation to designs with monolithically integrated DBRs. In the case of broad aperture designs enabled by SMSGs, monolithically integrated DBRs provide much more efficient heat dissipation in comparison to all other considered designs. [ABSTRACT FROM AUTHOR]

The incorporation of well-dispersed graphene oxide (GO) and graphene (G) has been demonstrated as a promising solution to improve the mechanical performance of polymethyl methacrylate (PMMA) bone cements in an attempt to enhance the long-term survival of the cemented orthopaedic implants. However, to move forward with the clinical application of graphene-based PMMA bone cements, it is necessary to ensure the incorporation of graphene-based powders do not negatively affect other fundamental properties (e.g., thermal properties and biocompatibility), which may compromise the clinical success of the implant. In this study, the effect of incorporating GO and G on thermal properties, biocompatibility, and antimicrobial activity of PMMA bone cement was investigated. Differential scanning calorimetry studies demonstrated that the extent of the polymerisation reaction, heat generation, thermal conductivity, or glass transition temperature were not significantly (p > 0.05) affected by the addition of the GO or G powders. The cell viability showed no significant difference (p > 0.05) in viability when MC3-T3 cells were exposed to the surface of G- or GO-PMMA bone cements in comparison to the control. In conclusion, this study demonstrated the incorporation of GO or G powder did not significantly influence the thermal properties or biocompatibility of PMMA bone cements, potentially allowing its clinical progression. [ABSTRACT FROM AUTHOR]

Among the composite manufacturing methods, injection molding has higher time efficiency and improved processability. The production of composites via injection molding requires a pre-process to mix and pelletize the matrix polymer and reinforcement material. Herein, we studied the effect of extrusion process conditions for making pellets on the mechanical and thermal properties provided by injection molding. Polyamide 6 (PA6) was used as the base, and composites were produced by blending carbon fibers and Al2O3 as the filler. To determine the optimum blending ratio, the mechanical properties, thermal conductivity, and melt flow index (MI) were measured at various blending ratios. With this optimum blending ratio, pellets were produced by changing the temperature and RPM conditions, which are major process variables during compounding. Samples were fabricated by applying the same injection conditions, and the mechanical strength, MI values, and thermal properties were measured. The mechanical strength increased slightly as the temperature and RPM increased, and the MI and thermal conductivity also increased. The results of this study can be used as a basis for specifying the conditions of the mixing and compounding process such that the desired mechanical and thermal properties are obtained. [ABSTRACT FROM AUTHOR]

This work investigates the impact of lignin origin and structural characteristics, such as molecular weight and functionality, on the properties of corresponding porous biopolymeric microspheres obtained through suspension-emulsion polymerization of lignin with styrene (St) and/or divinylbenzene (DVB). Two types of kraft lignin, which are softwood (Picea abies L.) and hardwood (Eucalyptus grandis), fractionated by common industrial solvents, and related methacrylates, were used in the synthesis. The presence of the appropriate functional groups in the lignins and in the corresponding microspheres were investigated by attenuated total reflectance Fourier transform infrared spectroscopy (ATR/FT-IR), while the thermal properties were studied by differential scanning calorimetry (DSC). The texture of the microspheres was characterized using low-temperature nitrogen adsorption. The swelling studies were performed in typical organic solvents and distilled water. The shapes of the microspheres were confirmed with an optical microscope. The introduction of lignin into a St and/or DVB polymeric system made it possible to obtain highly porous functionalized microspheres that increase their sorption potential. Lignin methacrylates created a polymer network with St and DVB, whereas the unmodified lignin acted mainly as an eco-friendly filler in the pores of St-DVB or DVB microspheres. The incorporation of biopolymer into the microspheres could be a promising alternative to a modification of synthetic materials and a better utilization of lignin. [ABSTRACT FROM AUTHOR]

This experimental study investigated the utility of a pitch-based carbon fiber–mortar composite, which could replace polyacrylonitrile carbon fiber, as a thin overlay for concrete pavement. The objective was to explore the utility of the low-cost carbon fiber, which was produced via a melt-blown method, i.e., blowing at high pressure after melting the pitch residue following crude oil purification. The mechanical properties, durability, and thermal properties of the pitch-based carbon fiber were explored to maximize strength, durability, functionality, and economy by using micro-sized fibers that are closer in size to the constituents of cementitious materials. Melt-blown pitch-based carbon fiber has low individual fiber strength but generally excellent thermal conductivity. Thermal conductivity tests were conducted on mortar panels (560 mm × 560 mm; thickness = 25, 40 or 60 mm) containing 0, 0.4, 0.5 or 0.6 wt % pitch-based carbon fiber. The absolute thermal conductivity tended to improve with higher wt % of pitch-based carbon fiber, in the range of 9~11 W/°C. However, thermal conductivity tended to be lower under the 0.6 wt % condition, possibly due to the effect of dispersion. Compressive strength degradation was tested over 350 cycles of freezing and thawing: the strength of the 0.4, 0.5 or 0.6 wt % samples was 91, 89, and 82%, respectively, relative to the control specimen (0 wt %). Thus, all specimens had a compressive strength of 80% or more after 350 cycles compared to the control specimen. To test the adhesion performance for new thin overlays and old concrete surfaces, concrete cylinders (100 × 200 mm; thickness = 10 mm) were cut at an angle of 46 degrees, and the pitch-based carbon fiber-mortar composite was used to bond the various sections. The bond strength of the test specimens was more than twice that of the reference specimen. [ABSTRACT FROM AUTHOR]

Two-dimensional graphene plateletes with unique mechanical, electrical and thermo-physical properties could attract more attention for their employed as reinforcements in the production of new metal matrix nanocomposites (MMNCs), due to superior characteristics, such as being lightweight, high strength and high performance. Over the last years, due to the rapid advances of nanotechnology, increasing demand for the development of advanced MMNCs for various applications, such as structural engineering and functional device applications, has been generated. The purpose of this work is to review recent research into the development in the powder-based production, property characterization and application of magnesium, aluminum, copper, nickel, titanium and iron matrix nanocomposites reinforced with graphene. These include a comparison between the properties of graphene and another well-known carbonaceous reinforcement (carbon nanotube), following by powder-based processing strategies of MMNCs above, their mechanical and tribological properties and their electrical and thermal conductivities. The effects of graphene distribution in the metal matrices and the types of interfacial bonding are also discussed. Fundamentals and the structure–property relationship of such novel nanocomposites have also been discussed and reported. [ABSTRACT FROM AUTHOR]

In this work, SiC and Cu particles were utilized to enhance the thermal and mechanical properties of Al matrix composites. The ball-milling and cold-compact methods were applied to prepare Al matrix composites, and the uniform distribution of SiC and Cu particles in the composite confirms the validity of our preparation method. After characterizing the thermal conductivity and the compressibility of the prepared composites, results show that small particles have a higher potential to improve compressibility than large particles, which is attributed to the size effect of elastic modulus. The addition of SiC to the Al matrix will improve the compressibility behavior of Al matrix composites, and the compressibility can be enhanced by 100% when SiC content is increased from 0 to 30%. However, the addition of SiC particles has a negative effect on thermal conductivity because of the low thermal conductivity of SiC particles. The addition of Cu particles to Al-SiC MMCs could further slightly improve the compressibility behavior of Al-SiC/Cu MMCs, while the thermal conductivity could be enhanced by about 100% when the Cu content was increased from 0 to 30%. To meet the need for low density and high thermal conductivity in applications, it is more desirable to enhance the specific thermal conductivity by enlarging the preparation pressure and/or sintering temperature. This work is expected to supply some information for preparing Al matrix composites with low density but high thermal conductivity and high compressibility. [ABSTRACT FROM AUTHOR]

This study presents a model for simulating the microscopic heat transfer processes in a wood-metal composite material. The model was developed by analyzing the microstructure of experimental samples comprising a melted alloy impregnated in a wood matrix. According to the thermal parameters of the materials and the boundary conditions, an analytical model of microscale heat transfer was established using Abaqus finite element analysis software. The model was validated experimentally by comparing temperature curves obtained via simulation and experiments; the resulting correlation coefficient was 0.96557. We then analyzed the temperature distribution of the composite material with different cell geometries and heat transfer conditions (heat transfer direction and applied temperature). The thermal properties of the unit cell models were in good agreement with the general trends predicted by several heat transfer equations. This study provides a method for analyzing the microscale heat transfer process in wood-based composites. In addition, the model framework characteristics can be used to evaluate the heat transfer mechanism of impregnated modified wood. [ABSTRACT FROM AUTHOR]