Search

As air pollution escalates, the need for air filters increases. It is better that the filters used be based on natural fibers, such as non-wood fibers, which cause low damage to the environment. However, the short fiber lengths, low apparent densities, and high volumes of non-wood materials can make it challenging to prepare filter paper with the required mechanical and physical properties. In that context, this study focused on utilizing bamboo fibers to fabricate filter paper by employing the anthraquinone soda pulping method. The pulp underwent bleaching and oxidation processes, with the incorporation of cationic starch (CS) and polyvinyl alcohol (PVA) to enhance resistance properties, resulting in the creation of handmade filter papers. The findings revealed that the tear, burst, and tensile strength of filter paper increased with the oxidation and addition of CS and PVA. Air permeability increased with addition of PVA and combination of CS and PVA. FTIR demonstrated the conversion of hydroxyl groups in cellulose chains to carboxyl groups due to oxidation. SEM images illustrated alterations in the fiber structure post-oxidation treatment, with CS reducing pores while PVA and the CS-PVA combination enlarged pore size and enhanced porosity. The BET surface area surface area expanded with oxidation and the addition of the CS-PVA blend, indicating heightened filter paper porosity. Notably, the combined inclusion of CS and PVA not only augmented mechanical strength but also increased porosity while maintaining pore size. [ABSTRACT FROM AUTHOR]

In this study, Al paper and cellulose acetate (CA) filters derived from heated tobacco waste were successfully converted into current collectors and active materials for a supercapacitor device. Typically, heated tobacco contains electrically discontinuous Al paper. First, Al was extracted from the tobacco waste using HCl to produce Lewis acid (AlCl3). This acid was then used in an Al electrodeposition process utilizing the chloroaluminate ionic liquid reaction between the acid and the base (RCl) at room temperature. To enhance the conductivity, a supplementary coating of Al metal was applied to the Al paper through electrodeposition, thus re-establishing the electrical continuity of the discontinuous parts and forming an Al-coated current collector. Moreover, the CA filters were carbonized under a nitrogen atmosphere, yielding carbon precursors (C-CA) for the supercapacitor electrodes. To further enhance the electrochemical performance, nickel oxide (NiO) was incorporated into C-CA, resulting in C-CA@NiO with pseudocapacitance. The specific surface area of CA increased with carbonization and the subsequent incorporation of NiO. The as-synthesized C-CA and C-CA@NiO materials were applied to an Al-coated current collector to obtain C-CA- and C-CA@NiO-based electrodes, exhibiting stable electrochemical behavior in the voltage range of −1.0 to 0 V and 0 to 1.0 V, respectively. An asymmetric supercapacitor (ASC) device was assembled with C-CA@NiO and C-CA as the positive and negative electrodes, respectively. This ASC device demonstrated a high specific capacitance of 40.8 F g−1, while widening the operating voltage window to 2.0 V. The high electrochemical performance of the device is attributed to the successful Al electrodeposition, which facilitates the electrical conductivity and increased porosity of the C-CA@NiO and C-CA materials. To the best of our knowledge, this is a pioneering study in regards to the conversion of biomass waste into current collectors and active materials to fabricate a practical ASC device. Our findings highlight the potential of reusing Al paper and CA filters from heated tobacco waste as essential components of energy storage devices. [ABSTRACT FROM AUTHOR]

Flexible paper-based materials play a crucial role in the field of flexible electromagnetic shielding due to their thinness and controllable shape. In this study, we employed the wet paper forming technique to prepare carbon fiber paper with a thickness gradient. The electromagnetic shielding performance of the carbon fiber paper varies with the ladder-like thickness distribution. Specifically, an increase in thickness gradient leads to higher reflectance of the carbon fiber paper. Within the X-band frequency range (8.2–12.4 GHz), reflectivity decreases as electromagnetic wave frequency increases, indicating enhanced penetration of electromagnetic waves into the interior of the carbon fiber paper. This enhancement is attributed to an increased fiber content per unit area resulting from a greater thickness gradient, which further enhances reflection loss and promotes internal multiple reflections and scattering effects, leading to increased absorption loss. Notably, at a 5 mm thickness, our carbon fiber paper exhibits an impressive average overall shielding performance, reaching 63.46 dB. Moreover, it exhibits notable air permeability and mechanical properties, thereby assuming a pivotal role in the realm of flexible wearable devices in the foreseeable future. [ABSTRACT FROM AUTHOR]

A thermoelectric generator (TEG) is one of the important energy harvesting sources for wearable electronic devices, which converts waste heat into electrical energy without any external stimuli, such as light or mechanical motion. However, the poor flexibility of traditional TEGs (e.g., Si-based TE devices) causes the limitations in practical applications. Flexible paper substrates are becoming increasingly attractive in wearable electronic technology owing to their usability, environmental friendliness (disposable, biodegradable, and renewable materials), and foldability. The high water-absorbing quality of paper restricts its scope of application due to water failure. Therefore, we propose a high-performance flexible waterproof paper-based thermoelectric generator (WPTEG). A modification method that infiltrates TE materials into cellulose paper through vacuum filtration is used to prepare the TE modules. By connecting the TE-modified paper with Al tape, as well as a superhydrophobic layer encapsulation, the WPTEG is fabricated. The WPTEG with three P–N modules can generate an output voltage of up to 235 mV at a temperature difference of 50 K, which can provide power to portable electronic devices such as diodes, clocks, and calculators in hot water. With the waterproof property, the WPTEG paves the way for achieving multi-scenario applications in humid environments on human skin. [ABSTRACT FROM AUTHOR]

This paper discusses the results of the micro-Raman analysis performed on paper-like graphene oxide (GO) samples consisting of many functionalised graphene layers and annealed at moderate temperatures (≤500 °C) under vacuum conditions (p ≃ 10−4 mbar). The analysis of the standalone samples revealed that the obtained material is characterised by a noticeable disorder level but still stays below the commonly accepted threshold of high or total disorder. GO formed in a simple way showed two spectral bands above 1650 cm−1 recorded very rarely or not at all and their origin has been discussed in detail. The results also confirmed the metastable character of multilayer GO after the annealing process at moderate temperatures as the C/O ratio was kept between 2 and 3 and the spectral features were stable within the annealing temperature range. [ABSTRACT FROM AUTHOR]

The dynamic mechanical behavior and cushioning performance of honeycomb sandwich panels, which are extensively employed in product cushioning packaging due to their exceptional energy absorption capabilities, were examined using a combination of experimental and numerical methods. Several factors, such as maximum acceleration–static stress, cushioning coefficient–static stress, and other curves, were analyzed under various impact conditions. The simulated stress–strain, deformation modes, cushioning coefficients, and other parameters demonstrate consistency with the experimental results. The acceleration, maximum compression, and cushioning coefficient obtained from the experiment and simulation calculation were 30.68 g, 15.44 mm, and 2.65, and 31.96 g, 14.91 mm, and 2.79, respectively. The results indicate that all error values were less than 5%, confirming the precision and reliability of the model. Furthermore, the model was utilized to simulate and predict the cushioning performance of honeycomb sandwich panels with different cell structures and paper thicknesses. These results provide a solid basis for enhancing the design of subsequent honeycomb element structures. [ABSTRACT FROM AUTHOR]

The formation of a cellular hierarchically organized NiO film on a carbon paper substrate under hydrothermal conditions using triethanolamine as a base has been studied. The thermal behavior of the carbon paper substrate with the applied semi-product shell was studied using synchronous thermal analysis (TGA/DSC) and it was demonstrated that such modification of the material surface leads to a noticeable increase in its thermal stability. Using scanning electron microscopy (SEM), it was shown that the NiO film grown on the carbon fiber surface is characterized by a complex cellular morphology, organized by partially layered individual nanosheets of about 4–5 nm thickness and lateral dimensions up to 1–2 μm, some edges and folds of which are located vertically relative to the carbon fiber surface. The surface of the obtained material was also examined using atomic force microscopy (AFM), and the electronic work function of the oxide shell surface was evaluated using the Kelvin probe force microscopy (KPFM) method. The electrochemical parameters of the obtained flexible NiO/CP electrode were analyzed: the dependence of the specific capacitance on the current density was determined and the stability of the material during cycling was studied, which showed that the proposed approach is promising for manufacturing hierarchically organized electrodes for flexible supercapacitors. [ABSTRACT FROM AUTHOR]

This work presents the results of paper laser processing. It begins with the selection and examination of the processing parameters, then an examination of the properties of the modified papers and examples of applications of the developed modification method. The properties of laser-modified paper were studied using reflectance spectrophotometry to examine the colour aspects of the modified papers, scanning electron microscopy (SEM) and confocal microscopy for a morphological analysis, and Raman spectroscopy to analyse the papers under the influence of laser light. The influence of laser processing on the wettability of paper and the evenness of unprinted and printed paper was also investigated. The knowledge gained on paper surface modification with laser light was used to propose several applications, such as methods of marking, tactile detection, the controlled removal of optical brightener, ink, and metallised coatings from paper packaging, highlighting the design and aesthetics of paper. The developed laser-assisted method shows a promising, ecological approach to the design of many value-added paper products. [ABSTRACT FROM AUTHOR]

The main objective of the presented research was to find a model that describes the maximum compressive force of paper in its plane. The research began with crushing tests of a number of packaging paper samples of various lengths. It was shown that due to the specific structure of the paper and the high heterogeneity of its structure, packaging paper is material where it is difficult to determine the maximum compressive stress. Next, three analytical models describing the load capacity of a flat paper web were investigated and an alternative empirical model was proposed. The results of the performed tests are directly applicable in the calculation of the mechanical properties of corrugated cardboard and the determination of the load capacity of cardboard packaging. [ABSTRACT FROM AUTHOR]

This paper examines the impact of the CO2 laser parameters on the tensile strength, which is one of the most important properties of paper packaging in the process of cutting paper material. The study was performed on a paper material sample Fbb Board/Ningbo Spark C1S Ivory Board by examination of the influence of four independent variables: paper material grammage, cutting speed, laser power, and resolution on the tensile strength by using definitive screening design. Optimum process conditions of four variables that maximize the tensile strength were predicted and validated accordingly. Results confirm that laser power, paper material grammage, and cutting speed are the main process parameters that mostly affect the tensile strength. Besides individual parameters, two statistically significant interactions were obtained: laser power and cutting speed, and cutting speed and laser resolution. Maximum tensile strength values (20.37 N/mm) were achieved using the laser power of 60.6%, cutting speed of 3.24%, resolution of 2500 Hz, and a paper material grammage of 326.85 g/m2. With laser power at middle values and at a lower speed, a maximum tensile strength value can be obtained. Increasing the laser power and cutting speed will produce a slight lowering of tensile strength. [ABSTRACT FROM AUTHOR]

The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill's anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods. [ABSTRACT FROM AUTHOR]

The applications of waste-derived fuel from paper mills in industrial boilers benefit the reduction of carbon emissions. However, the co-combustion of waste-derived fuel and coal causes significant changes in the characteristics of the ash and brings about the need to find possible means of the utilization of the ash produced. In this work fly, ash samples were collected from circulating fluidized bed (CFB) boilers co-combusting paper mill wastes with coal and analyzed in detail. The chemical, physical, and thermal characteristics of two different co-combustion fly ashes (CCFA) were investigated using X-ray fluorescence (XRF), X-ray diffraction (XRD), thermogravimetry (TG), and scanning electron microscope (SEM). The chemical composition of CCFA is largely affected by the fuel source type. Thermal analyses of CCFA show that the type of desulfurization system used by the boiler influences the form of sulfate present in the fly ash. The presence of calcium sulfite hemihydrate can cause a high loss in the ignition of CCFA. By comparing the physical requirements specified in the ASTM standard for coal fly ash to be used in concrete, the CCFA produced from paper mill wastes was found to show good potential as supplementary cementitious materials. [ABSTRACT FROM AUTHOR]

In protecting cultural heritage, deacidification is used to stabilize acidic papers, ensuring the neutralization of acids present in the paper. But in the process of aging, several mechanisms of degradation occur simultaneously. Therefore, substances used to stabilize the paper should contain an antioxidant component in addition to the deacidifying component. The effect of the antioxidant (hindered amine light stabilizers—HALS type) on the stabilization of lignin-containing acid papers during accelerated aging was studied in this work. The effective deacidification component was magnesium; the solvent was hexamethyldisiloxane (HMDSO). The 4-amino-2,2,6,6-tetramethylpiperidine series of hindered amine light stabilizers (HALS) was selected as appropriate for creating a modifying system based on HMDSO. The modification system was tested on samples of a model test acid lignin-containing paper (NOVO) and naturally aged acidic paper from the real book. The addition of substances to the proposed deacidification system has a favorable effect on stabilizing the pH during aging and provides the inhibition of the oxidative degradation products and stabilization of the cellulose degree of polymerization. It was confirmed that the application of the system containing deacidification and an antioxidant component may increase the effectiveness of the protection of acid groundwood paper heritage objects. Adding a tested antioxidant to the proposed deacidification system has a favorable effect on stabilizing the pH value for a long time in accelerated aging. [ABSTRACT FROM AUTHOR]

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties. [ABSTRACT FROM AUTHOR]

Sulfate attack is one of the drawbacks of cementitious materials for stabilized soils. In the current study, a durability comparison of stabilized soil with cement (Type IV) and waste paper fly ash (WPFA) was conducted. First, the treated soil's unconfined compressive strength (UCS) was tested. Next, the treated soil was subjected to various wetting/drying cycles with various sulfate concentrations and temperatures for a year. In the meantime, samples were taken for DRX, FTIR, and TGA microstructural analyses. Additionally, samples were manufactured to track swelling over an 800 day period. The outcomes show that WPFA's UCS remained constant. Furthermore, ettringite development can be seen in the microstructural studies, however testing on linear displacement over 800 days revealed no significant changes in swelling. Finally, SEM was used to verify the ettringite formation at 360 days in order to confirm the previous findings. All the results indicated that stabilizing soil with 5% of WPFA and 3% of cement IV is possible even in presence of high sulfate concentrations, while maintaining the durability of the structure. [ABSTRACT FROM AUTHOR]

Flexible calcium carbonate (FCC) was developed as a functional papermaking filler for high loaded paper, which was a fiber-like shaped calcium carbonate produced from the in situ carbonation process on the cellulose micro-or nanofibril surface. Chitin is the second most abundant renewable material after cellulose. In this study, a chitin microfibril was utilized as the fibril core for making the FCC. Cellulose fibrils for the preparation of FCC were obtained by fibrillation of the TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical) treated wood fibers. The chitin fibril was obtained from the β-chitin from the born of squid fibrillated in water by grinding. Both fibrils were mixed with calcium oxide and underwent a carbonation process by the addition of carbon dioxide, thus the calcium carbonate attached on the fibrils to make FCC. When used in papermaking, both the FCC from chitin and cellulose gave a much higher bulk and tensile strength simultaneously than the conventional papermaking filler of ground calcium carbonate, while maintaining the other essential properties of paper. The FCC from chitin caused an even higher bulk and higher tensile strength than those of the FCC from cellulose in paper materials. Furthermore, the simple preparation method of the chitin FCC in comparison with the cellulose FCC may enable a reduction in the use of wood fibers, process energy, and the production cost of paper materials. [ABSTRACT FROM AUTHOR]

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, "fusilli calabresi" type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS–PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS–PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food. [ABSTRACT FROM AUTHOR]

The surface-enhanced Raman scattering (SERS) properties of low-dimensional semiconducting MXene nanoflakes have been investigated over the last decade. Despite this fact, the relationship between the surface characteristics and SERSing performance of a MXene layer has yet to be comprehensively investigated and elucidated. This work shows the importance of surface morphology on the overall SERS effect by studying few-layer Ti3C2Tx MXene-based SERS substrates fabricated by vacuum-assisted filtration (VAF) and spray coating on filter paper. The VAF deposition results in a dense MXene layer suitable for SERS with high spot-to-spot and substrate-to-substrate reproducibility, with a significant limit of detection (LoD) of 20 nM for Rhodamine B analyte. The spray-coated MXenes film revealed lower uniformity, with a LoD of 50 nM for drop-casted analytes. Moreover, we concluded that the distribution of the analyte deposited onto the MXene layer is affected by the presence of MXene aggregates created during the deposition of the MXene layer. Accumulation of the analyte molecules in the vicinity of MXene aggregates was observed for drop-casted deposition of the analyte, which affects the resulting SERS enhancement. Ti3C2Tx MXene layers deposited on filter paper by VAF offer great potential as a cost-effective, easy-to-manufacture, yet robust, platform for sensing applications. [ABSTRACT FROM AUTHOR]

Thermochromic inks (TC) have received increasing attention in recent years, particularly in the design and packaging industries. Their stability and durability are crucial for their application. This study highlights the detrimental effects of UV radiation on the lightfastness and reversibility of thermochromic prints. Three commercially available TC inks with different activation temperatures and in different shades were printed on two different substrates, cellulose and polypropylene-based paper. Used inks were vegetable oil-based, mineral oil-based and UV-curable. The degradation of the TC prints was monitored using FTIR and fluorescence spectroscopy. Colorimetric properties were measured before and after exposure to UV radiation. The substrate with a phorus structure exhibited better colour stability, suggesting that the chemical composition and surface properties of the substrate play a crucial role in the overall stability of thermochromic prints. This can be explained by the ink penetration into the printing substrate. The penetration of the ink into the structure (cellulose fibres) protects the ink pigments from the negative effect of the UV radiation. Obtained results suggest that although the initial substrate may appear suitable for printing, its performance after ageing may not be optimal. In addition, the UV curable prints show better light stability than those made of mineral- and vegetable-based inks. In the field of printing technology, understanding the interplay between different printing substrates and inks is critical to achieve high-quality, long-lasting prints. [ABSTRACT FROM AUTHOR]

In this study, high-pressure laminates (HPL) impregnated with phenol-formaldehyde (PF) resins enriched with kraft lignin were developed. Pulverised kraft lignin was added to the commercial PF resin in the amounts of 1% and 5% (solid to solid). Laminates were manufactured using pressure impregnation of the resins into the papers and using hot pressing of HPL in a laboratory press. Laminates with a lignin content of 1% (L-LPF-1) showed the highest bending strength (72.42 MPa) and Brinell hardness (9.41); they also exhibited the best moisture uptake (9.61) and thickness swelling after immersion in water (3.32%). Except for impact bending, laminates with a lignin content of 5% (L-LPF-5) had worse properties. However, the differences between the variants are mostly not statistically significant and are comparable with the results of commercial PF resin. Scanning electron microscopy confirmed the homogenous structure of produced laminates and the occurrence of cohesive failures in ruptured L-LPF-1 laminates, whereas in ruptured L-LPF-5 laminates adhesive failures were also observed. Based on the conducted research it can be said that the utilisation of kraft lignin as an additive to PF resin (in the amount of 1%) has a positive effect on the produced HPL. [ABSTRACT FROM AUTHOR]

The title of the current Special Issue, "Feature Papers in Materials Simulation and Design", has identified the aims of this collection since its opening: the gathering of research works and comprehensive review papers that advance the understanding and prediction of material behavior at different scales, from atomistic to macroscopic, through innovative modeling and simulation. The paper by Chen et al. [[4]] aimed at studying the thermal properties and thermoelectric performance of imidazole-graphyne (ID-GY) by combining first principle calculations with the Boltzmann transport theory. The last paper by Cheng and Vescovini [[16]] presented instead an accurate and efficient numerical method for the analysis and design of Variable Stiffness (VS) laminates. Civalek et al. [[11]] developed an efficient eigenvalue algorithm for the axial vibration analysis of embedded short-fiber-reinforced micro-/nano-composite rods subjected to arbitrary boundary conditions. [Extracted from the article]

All-lignin coating formulations were prepared while combining water-soluble cationic kraft lignin (quaternized LignoBoost®, CL) and anionic lignosulphonate (LS). The electrostatic attraction between positively charged CL and negatively charged LS led to the formation of insoluble self-organized macromolecule aggregates that align to films. The structures of the formed layers were evaluated by atomic force microscopy (AFM), firstly on glass lamina using dip-coating deposition and then on handsheets and industrial uncoated paper using roll-to-roll coating in a layer-by-layer mode. Coated samples were also characterized by optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (SEM/EDS), and contact angle measurements. It was suggested that the structure of all-lignin aggregates is the result of the interaction of amphiphilic water-soluble lignin molecules leading to their specifically ordered mutual arrangement depending on the order and the mode of their application on the surface. The all-lignin coating of cellulosic fiber imparts lower air permeability and lower free surface energy to paper, mainly due to a decrease in surface polarity, thus promoting the paper's hydrophobic properties. Moderate loading of lignin coating formulations (5–6 g m−2) did not affect the mechanical strength of the paper. [ABSTRACT FROM AUTHOR]

Flexible respiratory monitoring devices have become available for outside-hospital application scenarios attributable to their improved system wearability. However, the complex fabrication process of such flexible devices results in high prices, limiting their applications in real-life scenarios. This study proposes a flexible, low-cost, and easy-processing paper-based humidity sensor for sleep respiratory monitoring. A paper humidity sensing model was established and sensors under different design parameters were processed and tested, achieving high sensitivity of 5.45 kΩ/%RH and good repeatability with a matching rate of over 85.7%. Furthermore, the sensor patch with a dual-channel 3D structure was designed to distinguish between oral and nasal breathing from origin signals proved in the simulated breathing signal monitoring test. The sensor patch was applied in the sleep respiratory monitoring of a healthy volunteer and an obstruct sleep apnea patient, demonstrating its ability to distinguish between different respiratory patterns as well as various breathing modes. [ABSTRACT FROM AUTHOR]

To study the friction and wear performance of carbon fiber reinforced friction materials under different working conditions, paper-based friction materials with different fibers were prepared. Experiments on the SAE#2 test bench were conducted to study the infectors including friction torques, surface temperature, coefficient of friction (COF), and surface morphologies. The results were analyzed, which indicated that the carbon fiber reinforced friction material could provide a higher friction torque and a lower temperature rising rate under the applied high pressure and high rotating speed conditions. As the pressure increased from 1 MPa to 2.5 MPa, the friction torque of plant fiber reinforced material increased by 150%, the friction torque of carbon fiber reinforced material increased by 400%, and the maximum temperature of plant fiber reinforced and carbon fiber reinforced material reached the highest value at 1.5 MPa. Thus, carbon fibers not only improved the COF and friction torque performance but also had advantages in avoiding thermal failure. Meanwhile, carbon fiber reinforced friction materials can provide a more stable COF as its variable coefficient (α) only rose from 38.18 to 264.62, from 1 MPa to 2.5 MPa, which was much lower than the natural fiber reinforced friction materials. Simultaneously, due to the good dispersion and excellent mechanical properties of PAN chopped carbon fibers, fewer pores formed on the initial surface, which improved the high wear resistance, especially in the intermedia disc. [ABSTRACT FROM AUTHOR]

In order to further improve the performance of impregnated paper decorated blockboard (ecological board), high-density fiberboard (HDF) was selected as the equilibrium layer to replace the commonly used poplar veneer. Results showed that the performance of HDF ecological board can be comparable to that of poplar veneer ecological board. It had good appearance quality, and its surface scratch resistance, surface wear resistance, water resistance and mechanical properties met the requirements of National Standard GB/T 34722-2017. The surface cracking resistance of the ecological board prepared with HDF as the equilibrium layer reached the highest level (grade 5), far better than that of the poplar veneer ecological board. This was because HDF was a relatively homogeneous material, and its dry shrinkage in both the transverse direction and along the grain direction was much lower than that of the poplar veneer. This characteristic of HDF made it possible to improve the dimensional stability and bending resistance of blockboard substrates under dry and hot conditions. The formaldehyde emission of the HDF ecological board was higher than that of the poplar veneer ecological board, but it met the formaldehyde emission requirements of indoor materials according to GB 18580-2001. [ABSTRACT FROM AUTHOR]

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties. [ABSTRACT FROM AUTHOR]

This study explores the pyrolysis process applied to various non-utilized waste materials, specifically focusing on separated plastics from municipal waste, wood waste (including pallets and window frames), paper rejects, and automotive carpets. Different combinations of these waste materials were subjected to pyrolysis, a process involving high-temperature treatment (600 °C) in a nitrogen atmosphere. The resulting products, including biochar, gas, and liquid fractions, as well as the residual waste materials, underwent comprehensive analysis. The evaluation of pyrolysis products emphasizes their quality, energy content, and potential applications. Notably, the pyrolysis gas derived from the combination of separated municipal plastics and waste wood exhibited the highest calorific value at 49.45 MJ/m3. Additionally, Mixture 2, consisting of plastic and wood waste, demonstrated the highest calorific value for the pyrolysis condensate, reaching 30.62 MJ/kg. Moreover, Mixture 3, benefiting from biochar utilization as a sorbent, displayed the highest iodine value at 90.01 mg/g. [ABSTRACT FROM AUTHOR]

The lightweight aggregates used by the civil engineering market are sintered at a high temperature, about 1200 °C. In times of high energy prices and regulation of carbon dioxide emissions, lightweight aggregate products of the high-temperature process in sales marketing are not readily accepted. This study developed a sintered-type paper sludge lightweight aggregate. In order to reduce energy consumption, substitution of some reservoir sediment clay in paper sludge substitutes is to be expected. The study used two types of paper sludge (green clay paper sludge and paper pulp sludge). The sintering temperature was reduced effectively as the green clay paper sludge was substituted for some of the reservoir sediment clay, and the optimum substitute ranges of green clay paper sludge were 10%-50%. The optimum substitute ranges of the paper pulp sludge were 10%-40%. Test results show that the properties of aggregates have a particle density of 0.66-1.69 g/cm3, a water absorption of 5%-30%, and a loss on ignition of 10%-43%. The loss on ignition of aggregate became greater with the increase in paper sludge content. This means that the calorific value provided by the paper sludge will increase as paper sludge content increases. Paper sludge can therefore be considered a good material to provide heat energy for sintering lightweight aggregate. [ABSTRACT FROM AUTHOR]

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then, vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performances of one kind of GOP and three kinds of GOPC diaphragm headphones are analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms. [ABSTRACT FROM AUTHOR]

The preparation of graphene materials from biomass resources is still a challenge, even more so if they are going to be employed as supports for electrocatalysts for water splitting. Herein, we describe the preparation and characterization of graphene oxides (GOs) from solid macroalgae waste obtained after processing an agar–agar residue. The structural and morphological characterization of the obtained GO confirm the presence of a lamellar material that is composed of few layers with an increased number of heteroatoms (including nitrogen) if compared with those observed in a GO obtained from graphite (reference). Three-dimensional electrodes were prepared from these GOs by depositing them onto a fibrous carbon paper, followed by electrodeposition of the catalyst, NiFe. The electrocatalytic performance of these hybrid systems for the oxygen evolution reaction (OER) showed a proactive effect of both graphene materials toward catalysis. Moreover, the electrode prepared from the algae-based graphene showed the highest electrocatalytic activity. This fact could be explained by the different structure of the algae-based graphene which, due to differences in the nucleation growth patterns and electroactive sites developed during the electrodeposition process, produced more reactive NiFe species (higher oxidation state). [ABSTRACT FROM AUTHOR]

In recent years, several studies have reported the recycling of by-products generated by the paper industry and their application to the construction industry. A majority of the existing studies used waste paper sludge ash, and considerable energy is consumed in such incineration processes. This may further contribute to air pollution. In this study, we used waste newspaper (WNP), which underwent a simple crushing process without a separate high-temperature treatment process, and we integrated it in cement mortar. We prepared mortars containing 0%, 0.2%, 0.4%, 0.6%, 0.8%, and 1.0% ground WNP as a cement substitute. Subsequently, the fluidity, compressive strength, tensile strength, carbonation depth, drying shrinkage, and microstructure of the mortars were compared and analyzed. The 28-day compressive strength of the mortar samples with WNP was approximately 3.2–16.1% higher than that of the control sample. The 28-day accelerated carbonation depth of the samples with WNP was approximately 1.03–1.61 mm. Furthermore, their carbonation resistance was approximately 5.2–39.4% higher than that of the control sample. Compressive strength, tensile strength, and carbonation resistance were improved by appropriately using ground WNP as a cement substitute in cement mortar. In this study, the appropriate amount of WNP according to the mechanical properties of cement mortar was found to be 0.4–0.8%, and considering the durability characteristics, the value 0.6 was the most ideal. [ABSTRACT FROM AUTHOR]

In kraft paper mills, supersonic steam jets are used to remove deposits that build up on the heat exchanger tubes in the recovery boiler. In this study, the fracture toughness KC and work of fracture, WF, of simulated boiler deposits were measured at temperatures up to 500 °C to determine the optimal conditions for deposit removal. The model deposits experienced an important brittle to ductile transition at ~450 °C. Above this temperature, ductile deposits required lower peak force, but four times more energy to fracture when compared to those tested at lower temperatures. The transition was clear in scanning electron micrographs of the fracture surfaces. The findings have significant implications for mills wishing to optimize sootblower performance. [ABSTRACT FROM AUTHOR]

In this work, we present a systematic study on solid Surface Enhanced Raman Scattering (SERS) substrates consisting of Au and Ag nanoparticles (NPs) loaded on filter paper with the dip-coating method. The aim of this work is to explore how a series of parameters (e.g., concentration of colloidal solution, different porosity of filter paper, and the presence of an aggregating agent) affects the analytical performance of paper-based SERS substrates. All the substrates developed in this study have been analyzed with two non-resonant probe molecules, 4-mercaptobenzoic acid (4-MBA) and adenine, in terms of (i) inter-sample repeatability, (ii) intra-sample repeatability, (iii) sensitivity, and (iv) overall SERS performance in terms of analyte quantification. Moreover, the issue of how to evaluate the repeatability for a solid SERS substrate is carefully discussed. [ABSTRACT FROM AUTHOR]

The dynamic pore systems and high surface areas of flexible metal-organic framework materials make them excellent candidates to be used in different kinds of adsorption processes. However, the adsorption and desorption behaviors of therapeutic drugs on metal-organic frameworks in solution are not fully developed. Here, we systematically investigated the adsorption and desorption behaviors of a typical therapeutic drug, verapamil, over several Zr-based metal-organic frameworks [e.g., Zr-FUM, UiO-66(Zr), UiO-66(Zr)-NH2 and UiO-66(Zr)-2COOH] as well as ZrO2 in an acetonitrile solution by using paper spray mass spectrometry. In contrast to other materials, UiO-66(Zr)-2COOH demonstrated a superior adsorption performance to verapamil due to their strong acid-base and/or hydrogen-bond interactions, and the adsorption process fitted well with the pseudo-second-order kinetic model. As verapamil-adsorbed materials were used for desorption experiments, ZrO2 demonstrated the most favorable desorption performance, whereas UiO-66(Zr)-2COOH yielded the poorest desorption capability. These Zr-based materials had also been coated at the surface with filter papers for the analysis of various drugs and proteins in the process of paper spray mass spectrometry. The results demonstrated that among the studied materials, ZrO2-coated paper gave the most favorable desorption performance as a pure drug solution, whereas the paper from UiO-66(Zr) demonstrated the optimal capability in the analyses of therapeutic drugs in a complex matrix (e.g., blood) and a protein (e.g., myoglobin). [ABSTRACT FROM AUTHOR]

The article presents continued considerations presented in a prior publication on the development of a model for calculating the bending stiffness BS of cellular honeycomb paperboards, applying the strength properties of paper raw materials used for the production of paperboard and the geometric parameters of cellular board. The results of BS calculations obtained by using the analytical model presented in the prior publication were significantly overestimated in relation to the value obtained by measurements. The calculation error in relation to the measurement value for the tested group of paperboards in the case of bending stiffness in the machine direction MD was within the range from 23% to 116%, and the average error was 65%, while in the cross direction CD, it was within the range from 2% to 54%, and the average error was 31%. The calculation model proposed in this work based on the physical properties of cellular paperboard reduces the error values for bending stiffness in both the machine and cross directions. The value of the average error for both main directions in the paperboard plane was 10%. The method enables more accurate determination of BS in the machine direction MD and in the cross direction CD at the paperboard design stage. In order to validate the proposed analytical model, the calculation results were compared with the results of BS laboratory measurements performed using the four-point bending method and, in order to expand the group of tested paperboards, with the measurement results presented in the prior article for cardboards with different raw material composition and different geometric parameters. [ABSTRACT FROM AUTHOR]

Worldwide, the need for thermal insulation materials used to increase the energy performance of buildings and ensure indoor thermal comfort is constantly growing. There are several traditional, well-known and frequently used thermal insulation materials on the building materials market, but there is a growing trend towards innovative materials based on agro-industrial waste. This paper analyses the performance of 10 such innovative thermal insulation materials obtained by recycling cellulosic and/or animal waste, using standardised testing methods. More precisely, thermal insulation materials based on the following raw materials were analysed: cellulose acetate, cigarette filter manufacturing waste; cellulose acetate, cigarette filter manufacturing waste and cigarette paper waste; cellulose acetate, waste from cigarette filter manufacturing, waste cigarette paper and waste aluminised paper; cellulose from waste paper (two types made by two independent manufacturers); wood fibres; cellulose from cardboard waste; cellulose from waste cardboard, poor processing, inhomogeneous product; rice husk waste and composite based on sheep wool, recycled PET fibres and cellulosic fibres for the textile industry. The analysis followed the performance in terms of thermal insulating quality, evidenced by the thermal conductivity coefficient (used as a measurable indicator) determined for both dry and conditioned material at 50% RH, in several density variants, simulating the subsidence under its own weight or under various possible stresses arising in use. The results showed in most cases that an increase in material density has beneficial effects by reducing the coefficient of thermal conductivity, but exceptions were also reported. In conjunction with this parameter, the analysis of the 10 types of materials also looked at their moisture sorption/desorption capacity (using as a measurable indicator the amount of water stored by the material), concluding that, although they have a capacity to regulate the humidity of the indoor air, under low RH conditions the water loss is not complete, leaving a residual quantity of material that could favour the development of mould. Therefore, the impact on indoor air quality was also analysed by assessing the risk of mould growth (using as a measurable indicator the class and performance category of the material in terms of nutrient content conducive to the growth of microorganisms) under high humidity conditions but also the resistance to the action of two commonly encountered moulds, Aspergillus niger and Penicillium notatum. The results showed a relative resistance to the action of microbiological factors, indicating however the need for intensified biocidal treatment. [ABSTRACT FROM AUTHOR]

Organic solvents with high purity are essential in various fields such as optical, electronic, pharmaceutical, and chemical areas to prevent low-quality products or undesired side-products. Constructing methods to remove impurities such as water residue in organic solvents has been a significant challenge. Within this article, we report for the first time a new method for the preparation of hydrophobic and oleophilic filter paper (named OCFP), based on thermally induced silane dehydrocoupling between cellulose-based filter paper and octadecylsilane. We comprehensively characterized OCFP using various characterization techniques (FTIR, XPS, XRD, and EDS). OCFP showed super-hydrophobic and oleophilic properties as well as remarkable water separation and removal efficiency (>93%) in various organic solvents with sustained reusability. In addition, the analytical results both before and after filtration of an NMR solvent using OCFP indicated that OCFP has an excellent solvent drying efficiency. This work presents a new strategy for the development of super-hydrophobic cellulose-based filter paper, which has great potential for solvent drying and water separation. [ABSTRACT FROM AUTHOR]

A Xi-shaped meta structure, has been introduced in this paper. A modified split-ring resonator (MSRR) and a capacitive loaded strip (CLS) were used to achieve the left-handed property of the metamaterial. The structure was printed using silver metallic nanoparticle ink, using a very low-cost photo paper as a substrate material. Resonators were inkjet-printed using silver nanoparticle metallic ink on paper to make this metamaterial flexible. It is also free from any kind of chemical waste, which makes it eco-friendly. A double negative region from 8.72 GHz to 10.91 GHz (bandwidth of 2.19 GHz) in the X-band microwave spectra was been found. Figure of merit was also obtained to measure any loss in the double negative region. The simulated result was verified by the performance of the fabricated prototype. The total dimensions of the proposed structure were 0.29λ x 0.29 λ x 0.007 λ. It is a promising unit cell because of its simplicity, cost-effectiveness, and easy fabrication process. [ABSTRACT FROM AUTHOR]

This paper presents a method for designing low carbon bio-based building materials, also named bio-concretes, produced with wood wastes in shavings form (WS) and cementitious pastes. As the aggregates phase of bio-concretes is composed of plant-based particles, known as porous and high water-absorbing materials, the bio-concretes cannot be designed by using the traditional design rules used for conventional mortar or concrete. Then, the method used in the current paper is an adaptation of a previous one that has been developed in a recent paper where bio-concretes were produced with a cement matrix, three types of bio-aggregates, and a proposal of a design abacus. However, when that abacus is used for designing WBC with low cement content in the matrix, the target compressive strength is not reached. In the present paper, the method is extended to low cement content matrix (up to 70% of cement substitution) and also considering the greenhouse gas (GHG) emission of the WBC. To obtain data for proposing a new design abacus, an experimental program was carried out by producing nine workable WBCs, varying wood volumetric fractions (40–45–50%), and water-to-binder ratios. The bio-concretes produced presented adequate consistency, lightness (density between 715 and 1207 kg/m3), and compressive strength ranging from 0.64 to 12.27 MPa. In addition, the GHG emissions of the WBC were analysed through the Life Cycle Assessment methodology. From the relationships obtained between density, compressive strength, water-to-binder ratio, cement consumption, and GHG emissions of the WBC, calibration constants were proposed for developing the updated and more complete abacus regarding an integrated mix design methodology. [ABSTRACT FROM AUTHOR]

This study evaluates the potential use of discarded plasterboard paper as fibers from buildings to reinforce concrete. Various concentrations of wastepaper fibers (0.5%, 1%, 1.5%, 2%, and 2.5% by weight of the binder) were investigated in this research. To mitigate the water absorption effect of the paper fibers, metakaolin was employed as a partial cement replacement. The results demonstrate that the inclusion of the wastepaper fiber enhances the mechanical and durability performance of the concrete. The optimal fiber proportion was identified as 1%, leading to a 29% increase in the compressive strength, a 38% increase in the splitting tensile strength, a 12% decrease in the water absorption, and a 23% decrease in the drying shrinkage with respect to the concrete containing 20% metakaolin. However, exceeding this optimal fiber content results in decreased mechanical and durability properties due to the fiber agglomeration and non-uniform fiber distribution within the concrete matrix. Based on the microstructural analysis, the improved performance of the concrete is ascribed to decreased porosity, more refined pore structure, and reduced propagation of microcracks within the concrete matrix in the presence of wastepaper fiber. According to the results, concrete containing 20% metakaolin and 1% wastepaper fiber exhibits durability and mechanical properties comparable to those of the traditional concrete. This finding highlights the significant promise of reducing dependency on conventional cement and incorporating suitable recycled materials, such as discarded plasterboard, and secondary by-products like metakaolin. Such a strategy encourages the preservation of resources, reduction in carbon dioxide emissions, and a decrease in the ecological footprint resulting from concrete production. [ABSTRACT FROM AUTHOR]

In order to explore the flexural behavior of a concrete sandwich panel under concentrated boundary conditions, based on Kirachhoff's elastic thin plate theory in this paper, the geometric deformation, physical conditions, and equilibrium relationship of a sandwich panel are deduced by constructing the layered analysis model of the sandwich panel, the basic differential equation of the flexural deformation of the concrete sandwich thin plate is obtained, and the mathematical expression of the internal force and displacement under the boundary condition of concentrated support is given. Combined with an engineering example, the proposed calculation method is verified. The results show that, in the arrangement of reliable connectors for concrete sandwich panels, the concrete wythes bear the load while the contribution of the core layer to the bending capacity of the structure can be ignored. When subjected to a laterally distributed load, the sandwich panel mainly experiences out-of-plane bending deformation, and the bending normal stress in the concrete panel layer shows a linear non-uniform distribution along the thickness direction of the panel. The bending deformation performance and bearing efficiency of a concrete sandwich slab with the change in concentrated support position have significant effects, and the load transfer efficiency can be improved by optimizing the arrangement of supports. Except for small local areas near the supports, the bending stress distribution and deformation behavior of the concrete sandwich panel can be accurately analyzed by the calculation method established in this paper. [ABSTRACT FROM AUTHOR]

The strain gauge method and the digital image correlation (DIC) method are commonly employed for measuring strain in tested objects, including material specimens and structural elements. The optical method enables the assessment of 3D strain fields across the entire area of interest, achieved through cameras and advanced software. The study investigates both quasi-static strength tests and more advanced research of structures. It explores full-scale construction testing, featuring highly stressed components of new wagon designs. The paper reviews the benefits and challenges of using the DIC method to measure large-scale elements. Conducting full-scale object testing is characterized by significant complexity, often involving interactions between elements, complex loading conditions, and the influence of friction. Numerous factors affect the measurements. Therefore, to compare both methods, an initially standard shear by tensile test of CFRP composite was analyzed. The analysis of strain maps provides valuable visualization of deformation patterns occurring during construction loading. The strain gauge method was crucial for verifying the quality of the DIC measurements. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. For strain values of 0.3% and above, a good match was obtained between optical and strain gauge measurements. Below this value, the results have less accuracy. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. The error comparison and discussion between different measurement scenarios were conducted. The paper presents a developed methodology for measuring strain and displacement state in complex and crucial structural elements. The method can be applied to measurements of heavily loaded components used in the transportation industry; for example, in railways. [ABSTRACT FROM AUTHOR]

Photoresists are fundamental materials in photolithography and are crucial for precise patterning in microelectronic devices, MEMS, and nanostructures. This paper provides an in-depth review of recent advancements in positive photoresist research and development, focusing on discussion regarding the underlying mechanisms governing their behavior, exploring innovative fabrication techniques, and highlighting the advantages of the photoresist classes discussed. The paper begins by discussing the need for the development of new photoresist technologies, highlighting issues associated with adopting extreme ultraviolet photolithography and addressing these challenges through the development of advanced positive-tone resist materials with improved patterning features, resolution, and sensitivity. Subsequently, it discusses the working mechanisms and synthesis methods of different types and subtypes of photoresists, starting from non-chemically amplified, organic, and inorganic–organic hybrid photoresists and progressing to dry film resists, with an emphasis on the upsides of each. The paper concludes by discussing how future research in the field of lithography—prioritizing concerns related to environmental impacts, improved photoresist material and properties, and utilization of advanced quantum technology—can assist with revolutionizing lithography techniques. [ABSTRACT FROM AUTHOR]

This paper presents the influence of adding rinsed ilmenite mud waste (R-MUD) on the microstructure of Portland cement composites, compared to similar composites containing fly ash (FA). The aim of the study is the assessment of the pozzolanic activity of ilmenite mud waste by its impact on the microstructure of the cement matrix in comparison to the undoubted pozzolanic activity of fly ash. The presented test results include pore size distribution, phase composition, pozzolanic activity using thermal analysis, R3 bound water test, and microstructural analysis using scanning electron microscopy (SEM). Tests were performed on mortars cured for up to 360 days. The results presented in this paper have shown that R-MUD has a pozzolanic activity level similar to FA or better, which influences pore size distribution in the composite and its microstructure. During the curing process, the microstructure of composites containing R-MUD became more compact and sealed than those with FA, which might also increase their durability. The results of the R3 tests have proven the pozzolanic activity of R-MUD but its level was lower than FA. R-MUD might be a useful substitute for fly ash, especially given the lack of good-quality fly ash on the market. [ABSTRACT FROM AUTHOR]

This paper explores the thermal behavior of multiple interface cracks situated between a half-plane and a thermal coating layer when subjected to transient thermal loading. The temperature distribution is analyzed using the hyperbolic heat conduction theory. In this model, cracks are represented as arrays of thermal dislocations, with densities calculated via Fourier and Laplace transformations. The methodology involves determining the temperature gradient within the uncracked region, and these calculations contribute to formulating a singular integral equation specific to the crack problem. This equation is subsequently utilized to ascertain the dislocation densities at the crack surface, which facilitates the estimation of temperature gradient intensity factors for the interface cracks experiencing transient thermal loading. This paper further explores how the relaxation time, loading parameters, and crack dimensions impact the temperature gradient intensity factors. The results can be used in fracture analysis of structures operating at high temperatures and can also assist in the selection and design of coating materials for specific applications, to minimize the damage caused by temperature loading. [ABSTRACT FROM AUTHOR]

This paper presents the results of the study of stress relaxation fields, deformation, and temperature of the system of nanostructured multilayer coatings. In the work, a nonlinear relationship between strain and stress was used to take into account nonlinear effects in the mechanism of nanostructure formation. The paper assumes that a friction surface is provided by the self-organization of shear components: both stress and strain on the one hand, and temperature on the other. The studied objects are described in the adiabatic approximation, taking into account the fact of the evolution of stresses and strains. With the help of phase portraits of the system, the dependence of the deformation processes on the stresses arising in the system without coating and with coating is shown. It is shown that the rate of change of deformation depends on the characteristics of the mechanical impact on the coating and on the amount of stress and deformation. A conclusion is drawn regarding the transition process in the presence of two regions (Hooke and plastic deformation) in the corresponding phase portrait of the strain–stress field of the system. The results of the work can be used to determine the effective parameters of a coating in the analysis of experimental time dependences of stresses. [ABSTRACT FROM AUTHOR]

The electrocatalytic production of ammonia has garnered considerable interest as a potentially sustainable technology for ammonia synthesis. Recently, non-metallic-doped materials have emerged as promising electrochemical catalysts for this purpose. This paper presents a comprehensive review of the latest research on non-metallic-doped materials for electrocatalytic ammonia production. Researchers have engineered a variety of materials, doped with non-metals such as nitrogen (N), boron (B), phosphorus (P), and sulfur (S), into different forms and structures to enhance their electrocatalytic activity and selectivity. A comparison among different non-metallic dopants reveals their distinct effects on the electrocatalytic performance for ammonia production. For instance, N-doping has shown enhanced activity owing to the introduction of nitrogen vacancies (NVs) and improved charge transfer kinetics. B-doping has demonstrated improved selectivity and stability, which is attributed to the formation of active sites and the suppression of competing reactions. P-doping has exhibited increased ammonia generation rates and Faradaic efficiencies, likely due to the modification of the electronic structure and surface properties. S-doping has shown potential for enhancing electrocatalytic performance, although further investigations are needed to elucidate the underlying mechanisms. These comparisons provide valuable insights for researchers to conduct in-depth studies focusing on specific non-metallic dopants, exploring their unique properties, and optimizing their performance for electrocatalytic ammonia production. However, we consider it a priority to provide insight into the recent progress made in non-metal-doped materials and their potential for enabling long-term and efficient electrochemical ammonia production. Additionally, this paper discusses the synthetic procedures used to produce non-metal-doped materials and highlights the advantages and disadvantages of each method. It also provides an in-depth analysis of the electrochemical performance of these materials, including their Faradaic efficiencies, ammonia yield rate, and selectivity. It examines the challenges and prospects of developing non-metallic-doped materials for electrocatalytic ammonia production and suggests future research directions. [ABSTRACT FROM AUTHOR]

The paper presents an analysis of the low-cycle fatigue (LCF) properties of C45, X20Cr13, and 34CrNiMo6 steels subjected to various heat treatment processes. Strain-controlled LCF tests were carried out with a total cyclic strain amplitude equal to 0.5, 1 and 1.5%. Fatigue life, cyclic stress-strain behavior and hardness were analyzed. Qualitative and quantitative relationships between material LCF properties resulting from the heat treatment processes, were related to the indentation force P*, which was derived experimentally by applying an instrumented indentation procedure with the use of the Vickers indenter. The proposed parameter P* and its changes ΔP* seem to be promising for the identification of the structural stress parameter σ* that is necessary for deriving values of the fatigue strength coefficients σf' corresponding to different tempering temperatures. The common feature of all steels analyzed in this paper is that the elastic parts of the strain-life characteristics remain parallel after being subjected to different tempering temperatures. [ABSTRACT FROM AUTHOR]

Geopolymers are binder materials that are produced by a chemical reaction between silica or aluminum compounds with an alkaline activating solution. Foamed geopolymer materials are increasingly being cited as a viable alternative to popular organic insulation materials. Since the foaming process of geopolymers is difficult to control, and any achievements in improving the performance of such materials are extremely beneficial, this paper presents the effect of the addition of basalt powder on the properties of foamed geopolymers. This paper presents the results of physicochemical studies of fly ash and basalt, as well as mechanical properties, thermal properties, and structure analysis of the finished foams. The scope of the tests included density tests, compressive strength tests, tests of the thermal conductivity coefficient using a plating apparatus, as well as microstructure tests through observations using light and scanning microscopy. Ground basalt was introduced in amounts ranging from 0 to 20% by mass. It was observed that the addition of basalt powder contributes to a reduction in and spheroidization of pores, which directly affect the density and pore morphology of the materials tested. The highest density of 357.3 kg/m3 was characterized by samples with a 5 wt.% basalt powder addition. Their density was 14% higher than the reference sample without basalt powder addition. Samples with 20 wt.% basalt addition had the lowest density, and the density averaged 307.4 kg/m3. Additionally, for the sample containing 5 wt.% basalt powder, the compressive strength exceeded 1.4 MPa, and the thermal conductivity coefficient was 0.1108 W/m × K. The effect of basalt powder in geopolymer foams can vary depending on many factors, such as its chemical composition, grain size, content, and physical properties. The addition of basalt above 10% causes a decrease in the significant properties of the geopolymer. [ABSTRACT FROM AUTHOR]

The development of sustainable flame retardants is gaining momentum due to their enhanced safety attributes and environmental compatibility. One effective strategy is to use waste materials as a primary source of chemical components, which can help mitigate environmental issues associated with traditional flame retardants. This paper reviews recent research in flame retardancy for waste flame retardants, categorizing them based on waste types like industrial, food, and plant waste. The paper focuses on recent advancements in this area, focusing on their impact on the thermal stability, flame retardancy, smoke suppression, and mechanical properties of polymeric materials. The study also provides a summary of functionalization methodologies used and key factors involved in modifying polymer systems. Finally, their major challenges and prospects for the future are identified. [ABSTRACT FROM AUTHOR]