Search

As a result of conventional wire-forming processes, the residual stress distribution in wires is frequently unfavorable for subsequent forming processes such as bending operations. High tensile residual stresses typically occur in the near-surface region of the wires and can limit further application and processability of the semi-finished products. This paper presents an approach for tailoring the residual stress distribution by modifying the forming process, especially with regard to the die geometry and the influence of the drawing velocity as well as the wire temperature. The aim is to mitigate the near-surface tensile residual stresses induced by the drawing process. Preliminary studies have shown that modifications in the forming zone of the dies have a significant impact on the plastic strain and deformation direction, and the approach can be applied to effectively reduce the process-induced near-surface residual stress distributions without affecting the diameter of the product geometry. In this first approach, the process variant using three different drawing die geometries was established for the metastable austenitic stainless steel X5CrNi18-10 (1.4301) using slow (20 mm/s) and fast (2000 mm/s) drawing velocities. The residual stress depth distributions were determined by means of incremental hole drilling. Complementary X-ray stress analysis was carried out to analyze the phase-specific residual stresses since strain-induced martensitic transformations occurred close to the surface as a consequence of the shear deformation and the frictional loading. This paper describes the setup of the drawing tools as well as the results of the experimental tests.

This investigation aims to analyze the effect of homogenization heat treatment at 1240 °C for 2 and 6 h on the hardness, distribution, morphology, and chemical composition of the δ-ferrite and sigma phases in 316L stainless steel cast billet. A field emission scanning electron microscope, combined with electron back-scattered diffraction, a field emission electron probe microanalyzer with a wavelength dispersive spectrometer, and a Vickers microhardness tester are applied to identify various phase evolutions in the cast billet. The morphology of the δ-ferrite and sigma phases in the austenite matrix of the 316L cast billet are strongly related to the subsequent hot and cold wire drawings. The homogenization heat treatment is expected to provide a driving force to form spheroid interdendritic δ-ferrite and to minimize the amount of the brittle sigma intermetallic compound in the austenite matrix. The homogenization heat treatment at 1240 °C effectively spheroidized all δ-ferrites into blunt ones in the cast billet. The transformation of δ-ferrite into sigma is dominated by temperature and cooling rate. The fast air cooling after homogenization between 1240 and 850 °C retards the precipitation of the sigma in the δ-ferrite. There are two δ-ferrite transformation mechanisms in this experiment. The direct transformation of the δ-ferrite into sigma is observed in the as-cast 316L stainless steel billet. In contrast, the eutectoid transformation of the δ-ferrite into the sigma and austenite dominates the 316L cast billet homogenized at 1240 °C, with a slow furnace cooling rate.

Temperature rise of a specimen is a significant issue in drawing industries for wire, rod, and bar products, because an excessive increase in temperature during the drawing process can deteriorate the product quality and die life. The influence of the strain hardening exponent (n) of a wire on the temperature and strain distributions during wire drawing is investigated to understand its effect and to improve the quality of drawn wire. Finite element analysis and experiments are conducted to analyze the temperature and strain distributions of wires with n values of 0.0, 0.1, 0.5, and 1.0. The temperature increase of the wire augments as the n of the wire increases, despite the same amount of ideal plastic deformation, which is associated closely with the redundant work. The shear strain increases with the n of the specimen, which generates redundant work, leading to a high temperature rise. Similarly, drawing force increases with the n of the specimen, owing to the increase in redundant work with the n of the wire. In addition, the drawing force presents a linear relationship with the temperature rise of the wire. The drawing speed should be reduced and/or the cooling of wire and die should be strengthened during wire drawing, with increasing n value of the wire, because product quality and die wear are highly associated with the temperature rise of the wire in the deformation zone.

This paper describes research on the influence the technology of zinc-coated steel wire manufacturing has on the energy and force parameters of the drawing process, energy consumption and zinc expenditure. In the theoretical part of the paper, the theoretical work and drawing power were calculated. Calculations of the electric energy consumption have shown that usage of the optimal wire drawing technology results in a 37% drop in energy consumption, which in the course of a single year translates to savings equal to 13 TJ. This, in turn, results in the decrease of CO2 emissions by tons and a total decrease of the eco-costs by approximately EUR 0.5 mln. Drawing technology also influences the losses of the zinc coating and CO2 emissions. Properly adjusted parameters of the wire drawing technology allow obtaining a zinc-coating that is 100% thicker, translating to 265 tons of zinc, whose production generates 900 tons of CO2 and incurs eco-costs equal to EUR 0.6 mln. Optimal parameters for drawing, from the perspective of decreased CO2 emissions during the zinc-coated steel wire manufacturing, are as follows: usage of the hydrodynamic drawing dies, angle of the die reducing zone α = 5°, and drawing speed of 15 m/s.

Round-notched samples are commonly used for testing the susceptibility to hydrogen embrittlement (HE) of metallic materials. Hydrogen diffusion is influenced by the stress and strain states generated during testing. This state causes hydrogen-assisted micro-damage leading to failure that is due to HE. In this study, it is assumed that hydrogen diffusion can be controlled by modifying such residual stress and strain fields. Thus, the selection of the notch geometry to be used in the experiments becomes a key task. In this paper, different HE behaviors are analyzed in terms of the stress and strain fields obtained under diverse loading conditions (un-preloaded and preloaded causing residual stress and strains) in different notch geometries (shallow notches and deep notches). To achieve this goal, two uncoupled finite element (FE) simulations were carried out: (i) a simulation by FE of the loading sequences applied in the notched geometries for revealing the stress and strain states and (ii) a simulation of hydrogen diffusion assisted by stress and strain, for estimating the hydrogen distributions. According to results, hydrogen accumulation in shallow notches is heavily localized close to the wire surface, whereas for deep notches, hydrogen is more uniformly distributed. The residual stress and plastic strains generated by the applied preload localize maximum hydrogen concentration at deeper points than un-preloaded cases. As results, four different scenarios are established for estimating “a la carte” the HE susceptibility of pearlitic steels just combining two notch depths and the residual stress and strain caused by a preload.

The effect of the thermal properties of steels on wire drawing behavior has been investigated to understand and improve the wire drawing process. Finite element analysis and experimental tests were conducted to analyze the temperature distribution of the deformed specimens with different thermal properties. The thermal properties of twinning-induced plasticity (TWIP) steel were measured and compared with those of plain carbon steel. Based on the measurement of thermal properties, wire drawing behaviors were systematically compared with thermal conductivity of the specimen (k) using plain low-carbon steel with high k and TWIP steel with low k. The results revealed that the k of TWIP steel was approximately one third of that of low-carbon steel, and the thermal expansion coefficient of the TWIP steel was approximately 50% higher than that of low-carbon steel in the temperature range of 26–400 °C. The temperature distributions in the wire strongly depended on the k of the wire during wire drawing. TWIP steel exhibited higher maximum temperature, and took a longer time to attain the equilibrium temperature than low-carbon steel during wire drawing owing to the low k. The maximum temperature of the die increased with decreasing k of the wire, indicating that die wear can increase with decreasing k of the wire. Therefore, reducing the drawing speed is suggested for a wire with low k, such as high-alloyed metals, especially for TWIP steels.

The different behaviors of the mechanical properties of drawn and caliber-rolled wires with applied strain were investigated to determine the appropriate process between wire drawing and caliber rolling with consideration of materials and process conditions. Ferritic, pearlitic, and TWIP steels were drawn and caliber-rolled under the same process conditions. Caliber-rolled wires exhibited a hardening behavior in the early deformation stage and softening behavior in the later deformation stage compared with the drawn wires, regardless of the steel. The hardening behavior of the caliber-rolled wires was explained by the higher strain induced by caliber rolling compared with wire drawing, especially the higher amount of redundant work in caliber-rolled wire. The caliber-rolled wire had approximately 36% higher strain than the drawn wire and approximately 85% higher strain than nominal strain. The softening behavior of the caliber-rolled wire in later deformation stages was related to the Bauschinger effect or low-cycle fatigue effect caused by the roll geometries and loading conditions during caliber rolling. The different intersection points of the tensile strength between drawn and caliber-rolled wires with the steels were attributed to the different strain hardening rates of each steel. Between the options of the caliber rolling and wire drawing processes, the appropriate process should be selected according to the strain hardening rate of the material and the amount of plastic deformation. For instance, when the wires need to deform at high levels, wire drawing is the better process because of the appearance of the Bauschinger effect in caliber-rolled wire.

The present study investigates, experimentally and numerically, the tensile behavior of copper-clad aluminum composite wires. Two fiber-matrix configurations, the conventional Al-core/Cu-case and a so-called architectured wire with a continuous copper network across the cross-section, were considered. Two different fiber arrangements with 61 or 22 aluminum fibers were employed for the architectured samples. Experimentally, tensile tests on the two types of composites show that the flow stress of architectured configurations is markedly higher than that of the linear rule of mixtures’ prediction. Transverse stress components and processing-induced residual stresses are then studied via numerical simulations to assess their potential effect on this enhanced strength. A set of elastic-domain and elastoplastic simulations were performed to account for the influence of Young’s modulus and volume fraction of each phase on the magnitude of transverse stresses and how theses stresses contribute to the axial stress-strain behavior. Besides, residual stress fields of different magnitude with literature-based distributions expected for cold-drawn wires were defined. The findings suggest that the improved yield strength of architectured Cu-Al wires cannot be attributed to the weak transverse stresses developed during tensile testing, while there are compelling implications regarding the strengthening effect originating from the residual stress profile. Finally, the results are discussed and concluded with a focus on the role of architecture and residual stresses.

The effect of changing the strain path on texture development, twin kinetics, and mechanical properties in twinning-induced plasticity steel was investigated to understand twinning behavior in more detail. Among the various plastic deformation processes, the wire drawing process was selected to achieve the aims of the study. Specimens of cold-drawn TWIP steel wire under the same effective strain but with different crystallographic textures were successfully fabricated using the effect of the wire drawing direction. Electron backscatter diffraction results showed that the drawn wires using both unidirectional (UD) and reverse-directional (RD) wire drawing processes were characterized as duplex fiber textures of major and minor . It was found that the RD wire had a higher fraction of component at both the center and surface areas compared to the UD wire, because the metal flow of the RD wire was beneficial for the development of a orientation. The pronounced crystallographic orientation of the RD wire activated the twinning rate and geometrically necessary dislocation density, leading to an increase in strength but a decrease in ductility. The strain path is as important as the amount of strain for strengthening the materials, especially those that are deformed by twinning.