Search

An experimental analysis of mechanical behaviour for aluminium-based fibre metal laminates under compression after impact was conducted. Damage initiation and propagation were evaluated for critical state and force thresholds. Parametrization of laminates was done to compare their damage tolerance. Relatively low-energy impact had a marginal effect on fibre metal laminates compressive strength. Aluminium–glass laminate was more damage-resistant than one reinforced with carbon fibres (6% vs. 17% of compressive strength loss); however, aluminium–carbon laminate presented greater energy dissipation ability (around 30%). Significant damage propagation before the critical load was found (up to 100 times the initial damaged area). Damage propagation for assumed load thresholds was minor in comparison to the initial damage size. Metal plastic strain and delaminations are dominant failure modes for compression after impact.

Dyes are highly toxic and persistent in the environment. Their presence in water causes environmental and social problems. Dyes must be effectively removed from the water. A UV/ZVI/H2O2 process was applied to decompose two organic dyes, AM E123 and AM ACID. A commercial ZVI product, Ferox Flow, was used, and its properties were determined using SEM and XRF. The zeta potential, surface area, and optical properties of ZVI were also determined. The efficiency of dye removal in optimal conditions was 85.5% and 80.85% for AM E123 and AM ACID, respectively. Complete decolorization was observed in all samples. The decomposition of both dyes occurred according to a modified pseudo-second-order reaction and there was a statistically significant correlation between the TOC decrease, pH, and process time. The catalyst was observed to have high stability, and this was not affected by the performance of the treatment process even after the third cycle, as confirmed by the results of the catalyst surface analysis and iron diffusion test. Slight differences in process efficiency were observed after each cycle. The need for only a small amount of catalyst to decompose AM E123 and AM ACID, coupled with the ability to reuse the catalyst without the need for prior preparation, may reduce catalyst purchase costs.

The combination of fibre metal laminates (FML) and sandwich structures can significantly increase the performance under impact of FMLs. The goal of this work was to create a material that will combine the superior properties of FMLs and foam sandwich structures in terms of the impact resistance and simultaneously have lower density and fewer disadvantages related to the manufacturing. An extensive impact testing campaign has been done using conventional fibre metal laminates (carbon- and glass-based) and in the proposed fibre foam metal laminates to assess and compare their behaviour. The main difference was observed in the energy absorption mechanisms. The dominant failure mechanism for fibre foam laminates is the formation of delaminations and matrix cracks while in the conventional fibre metal laminate the main failure mode is fibre cracking due to high local stress concentrations. The reduction in the fibre cracking leads to a better after-impact resistance of this type of structure improving the safety of the structures manufactured with these materials.

Point-of-use (POU) water treatment systems and devices play an essential role in limited access to sanitary safe water resources. The filtering materials applied in POU systems must effectively eliminate contaminants, be readily produced and stable, and avoid secondary contamination of the treated water. We report an innovative, 2D Ti3C2/Al2O3/Ag/Cu nanocomposite-modified filtration material with the application potential for POU water treatment. The material is characterized by improved filtration velocity relative to an unmodified reference material, effective elimination of microorganisms, and self-disinfecting potential, which afforded the collection of 99.6% of bacteria in the filter. The effect was obtained with nanocomposite levels as low as 1%. Surface oxidation of the modified material increased its antimicrobial efficiency. No secondary release of the nanocomposites into the filtrate was observed and confirmed the stability of the material and its suitability for practical application in water treatment.

This article presents selected aspects of an interlaminar shear strength and failure analysis of hybrid fiber metal laminates (FMLs) consisting of alternating layers of a 2024-T3 aluminium alloy and carbon fiber reinforced polymer. Particular attention is paid to the properties of the hybrid FMLs with an additional interlayer of glass composite at the metal-composite interface. The influence of hygrothermal conditioning, the interlaminar shear strength (short beam shear test), and the failure mode were investigated and discussed. It was found that fiber metal laminates can be classified as a material with significantly less adsorption than in the case of conventional composites. Introducing an additional layer of glass composite at the metal-composite interface and hygrothermal conditioning influence the decrease in the interlaminar shear strength. The major forms of damage to the laminates are delaminations in the layer of the carbon composite, at the metal-composite interface, and delaminations between the layers of glass and carbon composites.

The purpose of the work was the effect of metal volume fraction of fiber metal laminates on damage after dynamic loads based upon the example of innovative hybrid titanium−carbon composite laminates. The subject of the study was metal−fiber hybrid titanium−carbon composite laminates. Four types of hybrid titanium−carbon laminates were designed with various metal volume fraction coefficient but constant thickness. Based on the results, it can be stated that changes in the metal volume fraction coefficient in the range of 0.375−0.6 in constant thickness titanium−carbon composite laminates do not significantly affect their resistance to impacts in the energy range of 5−45 J. It was concluded that there were no significant differences in maximum force values, total contact time, and damage range. Some tendency towards a reduction in the energy accumulation capacity was observed with an increase in thickness of the metal part in relation to the total thickness of the laminate, especially in the lower impact energy range. This can result in the lower bending stiffness of laminates with lower metal content and potential elastic strain of the composite part before the initiation of the fiber damage process.

The aim of the study was to assess the selected properties of a hybrid organic−inorganic silane sol−gel coating (HSG) used in hybrid fiber metal laminates (FML) in a corrosion environment. The HSG coating on the aluminum alloy was produced using 3M™ AC130-2 formulation consisting of 3-glycidoxypropyl-trimethoxysilane (GPTMS) and tetra-n-propoxyzirconium (zirconium(IV) propoxide) (TPOZ). Laminates consisted of aluminum alloy AA2024-T3 sheets, with carbon fiber reinforced polymers (CFRPs) and a glass fiber reinforced metal−composite structure (GFRP). Potentiodynamic and polarization curve and impedance (EIS) tests were carried out on HSG at ambient temperatures after 1 h and 150 h of soaking. Neutral 0.5 M NaCl and 0.8 M NaCl solutions were used for open circuit potential (OCP) and potentiodynamic tests, and 0.5 NaCl was used for the EIS test. A neutral salt spray (NSS) test was applied to laminates with a 12 week exposure period. The results obtained revealed that the HSG coating did not provide sufficient protection against corrosion of the aluminum alloy in direct contact with an aggressive environment but was effective as an interlayer. Local aluminum sheet perforation did not lead to delamination at the metal−composite interface regardless of the type or configuration of the composite. This confirms the durability of HSG used in FMLs.