Search

Most commercial dressings with moderate to high exudate uptake capacities are mechanically weaker and/or require a secondary dressing. The current research article focuses on the development of hydrogel-based wound dressings combining mechanical strength with high exudate absorption capacities using acrylate-endcapped urethane-based precursors (AUPs). AUPs with varying poly(ethylene glycol) backbone molar masses (10 and 20 kg mol(-1)) and endcap chemistries are successfully synthesized in toluene, subsequently processed into UV-cured hydrogel sheets and are benchmarked against several commercial wound dressings (Hydrosorb, Kaltostat, and Mepilex Ag). The AUP materials show high gel fractions (>90%) together with strong swelling degrees in water, phosphate buffered saline and simulated wound fluid (12.7-19.6 g g(-1)), as well as tunable mechanical properties (e.g., Young's modulus: 0.026-0.061 MPa). The AUPs have significantly (p < 0.05) higher swelling degrees than the tested commercial dressings, while also being mechanically resistant. The elasticity of the synthesized materials leads to an increased resistance against fatigue. The di- and hexa-acrylated AUPs show excellent in vitro biocompatibility against human foreskin fibroblasts, as evidenced by indirect MTS assays and live/dead cell assays. In conclusion, the processed AUP materials demonstrate high potential for wound healing application and can even compete with commercially available dressings.

Gelatin is used widely in the biomedical field, among other for wound healing. Given its upper critical solution temperature, crosslinking is required. To this end, gelatin is chemically modified with different photo-crosslinkable moieties with low (32-34%) and high (63-65%) degree of substitution (DS): gelatin-methacrylamide (gel-MA) and gelatin-acrylamide (gel-AA) and gelatin-pentenamide (gel-PE). Next to the more researched gel-MA, it is especially interesting and novel to compare with other gelatin-derived compounds for the application of wound healing. An additional comparison is made with commercial dressings. The DS is directly proportional to the mechanical characteristics and inversely proportional to the swelling capacity. Gel-PE shows weaker mechanical properties (G' < 15 kPa) than gel-AA and gel-MA (G' < 39 and 45 kPa, respectively). All derivatives are predominantly elastic (recovery indices of 89-94%). Gel-AA and gel-MA show excellent biocompatibility, whereas gel-PE shows a significantly lower initial biocompatibility, evolving positively toward day 7. Overall, gel-MA shows to have the most potential to be applied as wound dressing. Future blending with gel-AA to improve the curing kinetics can lead to dressings able to compete with current commercial dressings.

Wound dressings under the form of films constituted of modified alginate (methacrylated alginate - AlgMA) versus a gelatine derivative containing norbornene functionalities (GelNB) are developed and evaluated for their moisturizing effects, followed by further in vivo testing to assay their wound healing potential. The gel fraction results shows that AlgMA and GelNB films displayed a high crosslinking efficiency while the swelling assay reveals a stronger water uptake capacity for AlgMA films compared to GelNB and to commercial dressing AquacelAg, used as positive control. Referring to the in vivo wound healing effect, the GelNB films not only exhibit proper healing properties, yet is higher to the AquacelAg, while the AlgMA films exhibit similar wound healing effect as the positive control. On a microscopic level, the healing phases (from inflammation to proliferation and contraction) are present for both materials, yet at a faster rate for the GelNB films, which is in line with the macroscopic findings. These results provide data which support that GelNB films outperform AlgMA films, but both can be used for wound healing applications.

Adipose tissue engineering aims to provide solutions to patients who require tissue reconstruction following mastectomies or other soft tissue trauma. Mesenchymal stromal cells (MSCs) robustly differentiate into the adipogenic lineage and are attractive candidates for adipose tissue engineering. This work investigates whether pore size modulates adipogenic differentiation of MSCs toward identifying optimal scaffold pore size and whether pore size modulates spatial infiltration of adipogenically differentiated cells. To assess this, extrusion-based 3D printing is used to fabricate photo-crosslinkable gelatin-based scaffolds with pore sizes in the range of 200-600 mu m. The adipogenic differentiation of MSCs seeded onto these scaffolds is evaluated and robust lipid droplet formation is observed across all scaffold groups as early as after day 6 of culture. Expression of adipogenic genes on scaffolds increases significantly over time, compared to TCP controls. Furthermore, it is found that the spatial distribution of cells is dependent on the scaffold pore size, with larger pores leading to a more uniform spatial distribution of adipogenically differentiated cells. Overall, these data provide first insights into the role of scaffold pore size on MSC-based adipogenic differentiation and contribute toward the rational design of biomaterials for adipose tissue engineering in 3D volumetric spaces.

Hydrogels are interesting as wound dressing for burn wounds to maintain a moist environment. Especially gelatin and alginate based wound dressings show strong potential. Both polymers are modified by introducing photocrosslinkable functionalities and combined to hydrogel films (gel-MA/alg-MA). In one protocol gel-MA films are incubated in alg-MA solutions and crosslinked afterward into double networks. Another protocol involves blending both and subsequent photocrosslinking. The introduction of alginate into the gelatin matrix results in phase separation with polysaccharide microdomains in a protein matrix. Addition of alg(-MA) to gel-MA leads to an increased swelling compared to 100% gelatin and similar to the commercial Aquacel Ag dressing. In vitro tests show better cell adhesion for films which have a lower alginate content and also have superior mechanical properties. The hydrogel dressings exhibit good biocompatibility with adaptable cell attachment properties. An adequate gelatin-alginate ratio should allow application of the materials as wound dressings for several days without tissue ingrowth. ispartof: MACROMOLECULAR BIOSCIENCE vol:19 issue:8 ispartof: location:Germany status: published

In hybrid bioprinting of cartilage tissue constructs, spheroids are used as cellular building blocks and combined with biomaterials for dispensing. However, biomaterial intrinsic cues can deeply affect cell fate and to date, the influence of hydrogel encapsulation on spheroid viability and phenotype has received limited attention. This study assesses this need and unravels 1) how the phenotype of spheroid-laden constructs can be tuned through adjusting the hydrogel physico-chemical properties and 2) if the spheroid maturation stage prior to encapsulation is a determining factor for the construct phenotype. Articular chondrocyte spheroids with a cartilage specific extracellular matrix (ECM) are generated and different maturation stages, early-, mid-, and late-stage (3, 7, and 14 days, respectively), are harvested and encapsulated in 10, 15, or 20 w/v% methacrylamide-modified gelatin (gelMA) for 14 days. The encapsulation of immature spheroids do not lead to a cartilage-like ECM production but when more mature mid- or late-stage spheroids are combined with a certain concentration of gelMA, a fibrocartilage-like as well as a hyaline cartilage-like phenotype can be induced. As a proof of concept, late-stage spheroids are bioprinted using a 10 w/v% gelMA-Irgacure 2959 solution with the aim to test the processing potential of the spheroid-laden bioink.

In the present work, a photopolymerized urethane-based poly(ethylene glycol) hydrogel is applied as a porous scaffold material using indirect solid freeform fabrication (SFF). This approach combines the benefits of SFF with a large freedom in material selection and applicable concentration ranges. A sacrificial 3D poly(ε-caprolactone) structure is generated using fused deposition modeling and used as template to produce hydrogel scaffolds. By changing the template plotting parameters, the scaffold channel sizes vary from 280 to 360 μm, and the strut diameters from 340 to 400 μm. This enables the production of scaffolds with tunable mechanical properties, characterized by an average hardness ranging from 9 to 43 N and from 1 to 6 N for dry and hydrated scaffolds, respectively. Experiments using mouse calvaria preosteoblasts indicate that a gelatin methacrylamide coating of the scaffolds results in an increased cell adhesion and proliferation with improved cell morphology.

In vascular tissue engineering, great attention is paid to the immobilization of biomolecules onto synthetic grafts to increase bio- and hemocompatibility-two critical milestones in the field. The surface modification field of poly(ethylene terephthalate) (PET), a well-known vascular-graft material, is matured and oversaturated. Nevertheless, most developed methods are laborious multistep procedures generally accompanied by coating instability or toxicity issues. Herein, a straightforward surface modification procedure is presented engineered to simultaneously promote surface endothelialization and anticoagulation properties via the covalent immobilization of gelatin through a photoactivated azide derivative. A complete physicochemical characterization and biological study including cytotoxicity and endotoxin testing are performed. In addition, biocompatibility toward small (diameter ≤ 6 mm) and/or large caliber (diameter ≥ 6 mm) vessels is assessed by micro- and macrovascular endothelial cell assays. Superior bio- and hemocompatibility properties are seen for the gelatin-covalently modified PET surfaces compared to the conventional surface-modification procedures based on physisorption.

The application of ozonization and cyclic voltammetry for the regeneration of gold chips containing a chemisorbed gelatin layer is reported. The efficiency of the regeneration process was analyzed using various surface analysis techniques indicating a complete removal of the biopolymer layer. The current findings open up perspectives for regeneration and multiple application of gold chips for SPR measurements.