Search

Six-phase machines are increasingly used in safety-critical applications due to their inherent fault-tolerant capabilities. Due to the greater complexity of controlling six-phase machines and the fast dynamics required in safety-critical applications, finite control set model predictive control (FCS-MPC) emerged as an ideal candidate for the control of six-phase machines. However, most of the available FCS-MPC strategies only apply to six-phase machines where the two sets of three-phase windings are star-connected with isolated neutral points (2N). Nevertheless, the 2N configuration does not take full advantage of the machine's capabilities in terms of fault tolerance. Hence, this paper proposes a predictive current control strategy based on virtual vectors for six-phase permanent magnet synchronous (PMSM) drives with a single isolated neutral point (1N) configuration. The proposed method reduces the current harmonic distortion, decreases the copper losses, and is suitable to operate the six-phase drive in fault-tolerant conditions. The included simulation and experimental results demonstrate the good performance obtained with the proposed strategy. [ABSTRACT FROM AUTHOR]

The topic of this paper is the determination of rotor harmonic losses in multiphase machines. Specifically, harmonic losses occur in the rotor winding and core due to higher-order spatial harmonics of the flux density. This phenomenon influences machine parameters and overall performance and increases temperature rise in parts of the rotor. The flux density distribution is determined by the stator magnetomotive force harmonic content, which is directly related to the winding distribution. A cage-rotor asymmetrical six-phase induction machine is selected for this case study. An analysis of different stator winding topologies and their influence on harmonic losses is presented. A finite element-based method for calculating the contribution of individual stator magnetomotive force harmonics to the rotor losses is developed and described in the paper. The analysis includes scenarios with different phase current waveforms to emphasize the issues specific to the asymmetrical six-phase machine. It is found that the magnetomotive force components generated by non-torque-producing current components contribute significantly to harmonic losses. The obtained results can represent a foundation for optimal stator winding topology selection. This work is intended to motivate the development of new and the modification of existing models to properly include rotor harmonic losses during the design, performance prediction, and control of multiphase machines. [ABSTRACT FROM AUTHOR]

Multiphase machines are very convenient for applications that require high reliability. In this two-part survey, the state of the art about fault tolerance in multiphase drives is reviewed. In Part 1, an overview including numerous fault types was presented, along with fundamental notions about multiphase drives. Here, in Part 2, the focus is placed on phase/switch open-circuit (OC) faults in particular, which have received the most attention in the literature. Phase OC failures involve OCs in stator phases or in converter-machine connections, and switch/diode OCs are frequently dealt with similarly or identically. Thanks to the phase redundancy of multiphase drives, their operation can be satisfactorily continued under a certain number of OCs. Nonetheless, the procedure to follow for this purpose is far from unique. For given OC fault conditions, numerous fault-tolerant possibilities can be found in the literature, each of them with different advantages and disadvantages. Moreover, a great variety of methods have also been devised to detect and diagnose phase/switch OC failures so that, as soon as possible, the most appropriate fault-tolerance measures are applied. Thus, given the broad literature about tolerance to phase/switch OC faults in multiphase drives, the survey presented here is expected to be of great interest for the research community and industry. [ABSTRACT FROM AUTHOR]

Multiphase drives offer enhanced fault-tolerant capabilities compared with conventional three-phase ones. Their phase redundancy makes them able to continue running in the event of faults (e.g., open/short-circuits) in certain phases. Moreover, their greater number of degrees of freedom permits improving diagnosis and performance, not only under faults affecting individual phases, but also under those affecting the machine/drive as a whole. That is the case of failures in the dc link, resolver/encoder, control unit, cooling system, etc. Accordingly, multiphase drives are becoming remarkable contenders for applications where high reliability is required, such as electric vehicles and standalone/off-shore generation. Actually, the literature on the subject has grown exponentially in recent years. Various review papers have been published, but none of them currently cover the state-of-the-art in a comprehensive and up-to-date fashion. This two-part paper presents an overview concerning fault tolerance in multiphase drives. Hundreds of citations are classified and critically discussed. Although the emphasis is put on fault tolerance, fault detection/diagnosis is also considered to some extent, because of its importance in fault-tolerant drives. The most important recent advances, emerging trends and open challenges are also identified. Part 1 provides a comprehensive survey considering numerous kinds of faults, whereas Part 2 is focused on phase/switch open-circuit failures. [ABSTRACT FROM AUTHOR]

Six-phase machines are increasingly used in safety-critical applications due to their inherent fault-tolerant capabilities. Due to the greater complexity of controlling six-phase machines and the fast dynamics required in safety-critical applications, finite control set model predictive control (FCS-MPC) emerged as an ideal candidate for the control of six-phase machines. However, most of the available FCS-MPC strategies only apply to six-phase machines where the two sets of three-phase windings are star-connected with isolated neutral points (2N). Nevertheless, the 2N configuration does not take full advantage of the machine’s capabilities in terms of fault tolerance. Hence, this paper proposes a predictive current control strategy based on virtual vectors for six-phase permanent magnet synchronous (PMSM) drives with a single isolated neutral point (1N) configuration. The proposed method reduces the current harmonic distortion, decreases the copper losses, and is suitable to operate the six-phase drive in fault-tolerant conditions. The included simulation and experimental results demonstrate the good performance obtained with the proposed strategy.

The topic of this paper is the determination of rotor harmonic losses in multiphase machines. Specifically, harmonic losses occur in the rotor winding and core due to higher-order spatial harmonics of the flux density. This phenomenon influences machine parameters and overall performance and increases temperature rise in parts of the rotor. The flux density distribution is determined by the stator magnetomotive force harmonic content, which is directly related to the winding distribution. A cage-rotor asymmetrical six-phase induction machine is selected for this case study. An analysis of different stator winding topologies and their influence on harmonic losses is presented. A finite element-based method for calculating the contribution of individual stator magnetomotive force harmonics to the rotor losses is developed and described in the paper. The analysis includes scenarios with different phase current waveforms to emphasize the issues specific to the asymmetrical six-phase machine. It is found that the magnetomotive force components generated by non-torque-producing current components contribute significantly to harmonic losses. The obtained results can represent a foundation for optimal stator winding topology selection. This work is intended to motivate the development of new and the modification of existing models to properly include rotor harmonic losses during the design, performance prediction, and control of multiphase machines.

Multiphase drives offer enhanced fault-tolerant capabilities compared with conventional three-phase ones. Their phase redundancy makes them able to continue running in the event of faults (e.g., open/short-circuits) in certain phases. Moreover, their greater number of degrees of freedom permits improving diagnosis and performance, not only under faults affecting individual phases, but also under those affecting the machine/drive as a whole. That is the case of failures in the dc link, resolver/encoder, control unit, cooling system, etc. Accordingly, multiphase drives are becoming remarkable contenders for applications where high reliability is required, such as electric vehicles and standalone/off-shore generation. Actually, the literature on the subject has grown exponentially in recent years. Various review papers have been published, but none of them currently cover the state-of-the-art in a comprehensive and up-to-date fashion. This two-part paper presents an overview concerning fault tolerance in multiphase drives. Hundreds of citations are classified and critically discussed. Although the emphasis is put on fault tolerance, fault detection/diagnosis is also considered to some extent, because of its importance in fault-tolerant drives. The most important recent advances, emerging trends and open challenges are also identified. Part 1 provides a comprehensive survey considering numerous kinds of faults, whereas Part 2 is focused on phase/switch open-circuit failures.