Search

Friction and very high temperature are still the major challenges in hard machining technology and they greatly affect cutting efficiency. The application of the MQL (minimum quantity lubrication) method, using nanoparticles in order to improve the cooling lubrication performance of the base cutting oil, has proven to be a promising solution. Hence, this work aimed to investigate the effectiveness of Al2O3/MoS2 hybrid nanofluid and Al2O3 and MoS2 mono nanofluids in the hard turning of 90CrSi steel (60–62 HRC) under an MQL environment. The Box-Behnken experimental design was used for three input variables, including nanoparticle concentration, air pressure, and air flow rate. Their influences on surface roughness and cutting forces were studied. According to the obtained results, it was shown that the application of hybrid nano cutting oils in MQL contributes to achieving better hard machining performance than the use of mono nanofluids. In particular, a lower cutting temperature is reported and the values of surface roughness Ra, back force Fp, and cutting force Fc were smaller and more stable under Al2O3/MoS2 hybrid nanofluid MQL than those under Al2O3 and MoS2 mono nanofluid MQL due to an improvement in cooling lubrication characteristics. Thus, this work provides a novel approach to study hybrid nanofluids for MQL hard machining.

In recent years, the application of environmentally friendly cutting fluids in the metal cutting industry has been a growing concern in all over the world. In this study, the minimum quantity cooling lubrication (MQCL) technique, which uses very small amount of cutting oil, is motivated to apply to the hard milling process of Hardox 500 steel. Further, rice bran oil, a natural biodegradable oil, is used as the base fluid of Al2O3/MoS2 hybrid nanofluid. ANOVA analysis is used to study the influences of nanoparticle concentration, cutting speed, and feed rate on surface roughness. The obtained results indicate that good surface quality is achieved and the cutting speed is significantly increased to 140 m/min (about 2.55–2.80 times higher than the recommended values) due to the better cooling and lubricating effects from MQCL system and Al2O3/MoS2 hybrid nanofluid. Moreover, the microstructure of the machined surface proves the formation of MoS2 tribo film by using Al2O3/MoS2 hybrid nanofluid, indicating that the effectiveness of each type of nanoparticle in hybrid nanofluid has been promoted. Furthermore, the important technical guides for machining Hardox 500 steel are provided.

The present work shows the process for MoS2 nanosheet production by liquid N2-queched bulk, a novel method having highly efficient, green, and facile operation. The produced MoS2 nanoparticles are suspended in minimum quantity cooling lubrication (MQCL)-based fluid to form nanofluid used for the hard milling of AISI D2 steel. The study aims to improve the hard-milling performance assisted by the MQCL technique using MoS2 nanofluid. ANOVA analysis is used to evaluate the effects of three input machining variables, including nanoparticle concentration, cutting speed, and material hardness on cutting forces. The results indicate that the better cooling effect from the principle of the Ranque–Hilsch vortex tube of the MQCL device combined with the better lubricating performance from MoS2 nanofluid brings out the sustainable alternative solution for machining difficult-to-cut material. Moreover, the experimental results provide the technical guides for the selection of proper values of nanoparticle concentration and cutting speed while ensuring the technological, economic, and environmental characteristics.

Hard machining has gained much attention to be an alternative solution for many traditional finish grinding operations due to high productivity, ease to adapt to complex part contours, the elimination of cutting fluids, good surface quality, and the reduction of machine tool investment. However, the enormous amount of heat generated from the cutting zone always requires the high-grade inserts and limits the cutting conditions. The MQL technique with nanofluids assisted for hard machining helps to improve the cutting performance while ensuring environmentally friendly characteristics. This paper focuses on the development of MQL technique by adding Al2O3 and MoS2 nanoparticles to the base fluids (soybean oil and water-based emulsion) for the hard turning of 90CrSi steel (60÷62 HRC). The analysis of variance (ANOVA) is used to evaluate the performance of MQL parameters in terms of cutting forces and surface roughness. The study reveals that a better performance of coated carbide inserts is observed by using MQL with Al2O3 and MoS2 nanofluids. In addition, the fluid type, nanoparticles and nanoparticle concentration have a strong effect on cutting performance. The interaction influence among the investigated variables is also studied in order to provide the technical guides for further studies using Al2O3 and MoS2 nanofluids.