Search

Few reports have addressed the effects of diode laser irradiation at 980 nm on the morphology and fracture resistance of dentine. The purpose of this study is to evaluate the effects of 980-nm diode laser on the ultrastructure and fracture resistance of root dentine. The roots of 90 extracted canine teeth were divided into three groups according to the type of irrigating solution (water, NaOCl, and NaOCl/EDTA) and subdivided into three subgroups (n = 10) according to the amount of laser irradiation (without irradiation, 1.5 W/100 Hz and 3.0 W/100 Hz). The roots were filled with an epoxy resin-based sealer and gutta-percha and then subjected to a fracture resistance test. Data were analyzed by ANOVA and the Tukey test (p < 0.05). Additionally, 18 canine teeth were prepared using the same irrigation/irradiation protocols and evaluated by scanning electron microscopy (SEM). The SEM showed greater changes when the laser power increased, and the changes also varied according to the irrigating solution. A modified smear layer was observed in specimens that were treated with water and then laser-irradiated. The laser treatment did not alter the fracture resistance of roots treated with 1.5 W/100 Hz (246.3 ± 29.5 N) and 3.0 W/100 Hz (215.3 ± 25.1 N) laser power. The roots treated with NaOCl were more susceptible to fracture (199.4 ± 15.1 N) than those irrigated with water (254.2 ± 23.0 N) (p < 0.05). The 980-nm diode laser altered the morphology of the dentine but did not affect the fracture resistance of the roots.

The purpose of this study is to assess the laser effect in root canal disinfection and periapical healing of endodontically treated teeth from patients with asymptomatic apical periodontitis. This study was performed as a randomized clinical trial. Thirty patients were selected according to the inclusion/exclusion criteria. Fifteen patients received the root canal retreatment (RCR) combined with 980-nm diode laser irradiation (LI). The canals were irrigated with saline solution and gently dried with paper points, keeping the dentin partially moist. The irradiation was performed using a 320-µm-diameter fiber in helicoidal movements (pulsed mode, power output of 1.5 W, 100 Hz for 20 s). The other 15 patients received the RCR with placebo irradiation (PI). Microbiological samples were taken in three periods: S1, after the filling material removal (baseline); S2, after laser or placebo irradiation (LI or PI); and S3, after the RCR followed by laser or placebo. The samples were submitted to the total microbial and E. faecalis counting. The periapical radiographic healing was analyzed after 3, 6, 9, and 12 months. Microbiological data (CFU/mg) were analyzed by ANOVA and Tukey's test (P < 0.05), and the repair by Mann-Whitney test (P < 0.05). In S2, the laser provided 42.44% microbial reduction and 53.14% of E. faecalis, different from the placebo that had no reduction, and 4.85% for Enterococcus (P < 0.05). In S3, the bacterial counts decreased without differences between groups. No differences in healing were found at 3 months. However, diode laser facilitated the repair from 3- to 12-month follow-up (P < 0.05) and had 45% more healed cases than placebo. Diode laser provided an antimicrobial effect before the biomechanical preparation but was not synergistic in RCR. It improved the periapical healing during follow-up., (© 2023. The Author(s), under exclusive licence to Springer-Verlag London Ltd., part of Springer Nature.)

The aim of this study is to evaluate the effect of different irrigation activation methods on root canal sealer penetration in teeth with simulated internal root resorption (IRR) and calcium hydroxide (CH) applied using a confocal laser scanning microscope (CLSM). 60 incisors with a single root and a single canal were included in the study. IRR cavities were created in the middle third of the root canal, and CH was placed. The samples were randomly divided into 4 groups (n = 15) according to the irrigation activation method to be tested: standard needle irrigation (SNI), sonic activation (EDDY), photon-induced photoacoustic flow (PIPS), and shock wave enhanced emission photoacoustic flow (SWEEPS). After irrigation activation applications, the root canals were obturated. Sections of 1.0 ± 0.1 mm were taken from the apical, middle, and coronal regions of each sample. The penetration area (µm 2 ) and maximum penetration depth (µm) of the root canal sealer were examined by CLSM and analyzed using ImageJ software. Statistical analysis was performed with a one-way ANOVA and post-hoc Tukey test at the P < 0.05 significance level. Among all irrigation activation methods tested, both the penetration area and maximum penetration depth of the root canal sealer were greater in the coronal region than in the apical region (p < 0.05). In the IRR region, there was no difference in terms of maximum penetration depth between PIPS and SWEEPS (p > 0.05), it was highest in SWEEPS (p < 0.05). PIPS and SWEEPS were better than other irrigation activation methods in the penetration of root canal sealer in the resorption areas of teeth with IRR., (© 2024. The Author(s), under exclusive licence to Springer-Verlag London Ltd., part of Springer Nature.)

This study aimed to compare the effects of diode and Er:YAG laser irradiation of root dentin on push-out bond strength of mineral trioxide aggregate (MTA) and calcium-enriched mixture (CEM) cements. An in vitro experimental study was conducted on 90 dentin discs, cut out of freshly extracted human teeth. The discs were instrumented to obtain 1.3-mm lumen diameter. Then, they were randomly divided into six groups (n = 15). Groups 1 and 4 subjected to diode laser (Wiser, Doctor Smile, Italy) (980 nm, 1 W, continuous mode) for 10 s and filled with MTA and CEM cements. Groups 2 and 5 subjected to Er:YAG laser (Deka, Italy) (2940 nm, 1 W, 10 Hz, 230 μs) for 10 s and filled with MTA and CEM cements. Groups 3 and 6 (control groups) were filled with MTA and CEM cements without laser irradiation. After 7 days, push-out bond strength test was performed using a universal testing machine in order to evaluate the adhesion of the biomaterials to dentin. The samples were evaluated under a light microscope at × 40 magnification to determine the mode of fracture. Data were analyzed using two-way ANOVA. The highest push-out bond strength (8.76 ± 3.62 MPa) was noted in group 1 (diode/MTA), which was significantly higher than the other groups (P < 0.001). The lowest bond strength (2.61 ± 0.81) was noted in group 6 (control/CEM). Diode laser significantly increased the bond strength of both cements (P < 0.05), but Er:YAG laser irradiation only increased the bond strength of CEM and had no significant effect on MTA (P = 0.603). The bond strength of MTA control group was higher than that of CEM control group (P = 0.001). Push-out bond strength of endodontic cements can be affected by dentin conditioning with diode 980 nm and Er:YAG laser. Nine hundred eighty-nanometer diode laser irradiation is recommended to increase the bond strength of endodontic cements particularly the CEM cement to dentin. [ABSTRACT FROM AUTHOR]

The aim of this study was to investigate the influence of tip design on patterns of laser energy dispersion through the dentine of tooth roots when using near-infrared diode lasers. Diode laser emissions of 810 or 940 nm were used in combination with optical fiber tips with either conventional plain ends or conical ends, to irradiate tooth roots of oval or round cross-sectional shapes. The lasers were operated in continuous wave mode at 0.5 W for 5 s with the distal end of the fiber tip placed in the apical or coronal third of the root canal at preset positions. Laser light exiting through the roots and apical foramen was imaged, and the extent of lateral spread calculated. There was a significant difference in infrared light exiting the root canal apex between plain and conical fiber tips for both laser wavelengths, with more forward transmission of laser energy through the apex for plain tips. For both laser wavelengths, there were no significant differences in emission patterns when the variable of canal shape was used and all other variables were kept the same (plain vs conical tip, tip position). To ensure optimal treatment effect and to prevent the risks of inadvertent laser effects on the adjacent periapical tissues, it is important to have a good understanding of laser transmission characteristics of the root canal and root dentine. Importantly, it is also essential to understand transmission characteristics of plain and conical fibers tips. [ABSTRACT FROM AUTHOR]

The aim of this study was to evaluate in vitro the influence of high-power lasers (Nd:YAG and diode 980 nm) associated with mineral coal as fotopotencializer on bond strength of an epoxy resin-based root canal sealer to root dentin, using the pushout test, and on the dentin/filling material interface, using confocal laser microscopy. For this purposes, 50 canines were instrumented with Mtwo rotary system up to #50.04 instrument and randomly assigned to five groups (n = 10): group I-control EDTAC; group II-EDTAC and Nd:YAG laser; group III-EDTAC and diode laser 980 nm; group IV-EDTAC, Nd:YAG laser and mineral coal 5 g/100 mL; and group V-EDTAC, diode laser 980 nm and mineral coal 5 g/100 mL. All data were analyzed by ANOVA (at 5% significance level) following the Kruskal-Wallis, Dunn and Tukey tests. The group I increased more bond strength of the sealer to root dentin that treated with only EDTAC 17% (17.21 ± 21.75 MPa), similar to the group II (12.21 ± 18.20 MPa) and group IV (14.92 ± 28.06 MPa), both treated with Nd:YAG laser, with the exception of group IV, which was added to mineral coal. The group V (8.75 ± 13.42 MPa) had similar results to the groups II and IV, but the same similarity were found when compared with group III (7.11 + 11.28 MPa), with lower results. Regarding the root thirds, the apical third (23.27 ± 29.21 MPa) presented a statistically higher value on bond strength than the cervical third (5.92 ± 5.33 MPa) and middle third (6.93 ± 7, 11 MPa) (p > 0.05). Group II (86.27 μm) showed the highest tags penetration values, with a statistically difference to the group III (51.57 μm), IV (36.77 μm) and V (32.37 μm) (p < 0.05). Group I (71.63 μm) was statistically similar to groups II and III (p > 0.05). Group IV had the lowest values and was statistically similarity to groups III and V (p > 0.05). It was concluded that the treatment with Nd:YAG laser provides better results than the diode 980 nm laser, except when was added mineral coal. The control and diode 980 nm laser groups presented less adhesive failures and more mists failures than the other groups. Both lasers did not interfere negatively compared to the control group. [ABSTRACT FROM AUTHOR]

The treatments for dentin hypersensitivity (DH) may change the surface roughness of the root dentin, which can lead to biofilm accumulation, increasing the risk of root caries. The aim was to compare the surface roughness of root dentin after different treatments of DH and the biofilm formation on those surfaces. After initial surface roughness (Sa) assessment, 50 bovine root fragments received the following treatments (n = 10): G 1-no treatment; G2-5% sodium fluoride varnish; G3-professional application of a desensitizing dentifrice; G4-toothbrushing with a desensitizing dentifrice; and G5-diode laser application (908 nm; 1.5 W, 20 s). The Sa was reevaluated after treatments. Afterward, all samples were incubated in a suspension of Streptococcus mutans at 37 °C for 24 h. The colony-forming units (CFU) were counted using a stereoscope, and the results were expressed in CFU/mL. The one-way ANOVA and the Tukey's tests compared the roughness data and the results obtained on the bacterial adhesion test (α = 5%). G2 (2.3 ± 1.67%) showed similar Sa variation than G1 (0.25 ± 0.41%) and G5 (5.69 ± 0.99%), but different from group G3 (9.05 ± 2.39%). Group 4 showed the highest Sa variation (30.02 ± 3.83%; p < 0.05). Bacterial adhesion was higher in G4 (2208 ± 211.9), suggesting that bacterial growth is greater on rougher surfaces. The diode laser and the conventional treatments for DH may change the surface roughness of the root dentin, but only brushing with desensitizing dentifrice induced a higher bacteria accumulation on root dentin surface. [ABSTRACT FROM AUTHOR]

The purpose of this study was to evaluate the effects of potassium-titanyl-phosphate (KTP) laser irradiation on smear layer removal and temperature changes of the root surfaces. Two hundred four extracted single-root human premolars were included. The canals were instrumented and divided into two main groups: group A (smear layer examination n:119) and group B (temperature change examination n:85). Each group was divided into subgroups (n:17) according to the different five laser power settings: A1, B1: 1 W-5.33 J/cm2; A2, B2: 1.5 W-7.52 J/cm2; A3, B3: 2 W-10.3 J/cm2; A4, B4: 3 W-15.5 J/cm2, A5, B5: 4 W-20.1 J/cm2, A6: positive control no laser irradiation-irrigated 2 mL for 2 min 2.5% NaOCl + 2 mL distilled water and A7: negative control groups no laser irradiation irrigated 2 mL for 2 min 17% EDTA + 2 mL for 2 min 2.5% NaOCl + 2 mL distilled water. The temperature elevations were measured with an infrared thermographic camera and smear layer examined by scanning electron microscope. According to Kruskal-Wallis and Tukey's tests, in all groups the highest smear scores were in the apical third. In all areas, there were statistically significant differences between negative control group (17% EDTA) and all other groups (p < 0.05). The highest smear scores were determined in 1 W KTP laser and positive control (2.5% NaOCl) groups. Statistically, in all thirds, the differences the 3 W and 4 W KTP laser groups between each other and all other groups were significant (p < 0.05). After the end of the use of the laser, increase in temperature values in all groups were found to be below 10 °C in 20 s. [ABSTRACT FROM AUTHOR]

This study is to investigate the efficacy of different irrigant activation techniques on removal of accumulated hard tissue debris (AHTD) in mesial roots of human mandibular molars. Extracted human mandibular molars with an isthmus between the mesial root canals were selected based on micro-CT (μCT) scans. The mesial canals were instrumented to an apical diameter ISO30 using ProTaper rotary files. Teeth were randomly assigned to three irrigant activation groups (n = 10): ultrasonically activated irrigation (UAI) using a size 20 Irrisafe for 3 × 20 s, laser-activated irrigation (LAI) with an Er:YAG laser (2940 nm) and plain 300 μm fiber tip inside the canal (20 mJ, 20 Hz, 3 × 20 s), and laser-activated irrigation with identical parameters with a 400 μm photon-induced photoacoustic streaming (PIPS) tip held at the canal entrance. All teeth were scanned with μCT before and after instrumentation and after irrigant activation. After reconstruction and image processing, the canal system volume filled with hard tissue debris before and after irrigant activation was calculated. Changes in hard tissue debris volumes were compared between groups using one-way ANOVA. The percentage volume of hard tissue debris (vol%) was significantly lower after irrigant activation in all groups. Although the lowest debris values were observed in the laser groups, no significant differences in the vol% of accumulated hard tissue debris after activation were observed between groups. Accumulated hard tissue debris was reduced significantly in all activation groups. Ultrasonically and laser-activated irrigation regimens performed similarly in this respect. None of the tested methods was able to render the root canal systems free of debris. [ABSTRACT FROM AUTHOR]

The aim of this study was to evaluate the chemical stability of endodontic-treated root dentin after different laser irradiations through Raman spectroscopy. Fifty maxillary canines were selected and prepared with K3 system. Roots were randomly distributed into five groups (n = 10) according to the surface treatment: GI (water), GII (NaOCl + EDTA), GIII (NaOCl + EDTA + 980 nm Diode laser), GIV (NaOCl + EDTA+ 1064 nm Nd: YAG laser) and GV (NaOCl + EDTA+ 2780 nm Er,Cr: YSGG laser). Lasers were applied for 20 s. Samples were bisected, and the organic and inorganic content of dentin was analyzed by Raman spectroscopy. Data were submitted to ANOVA and Tukey tests (p < 0.05). None of the surface treatments alter the inorganic content (cts) (p = 0.183). Roots irradiated with Er,Cr: YSGG laser had a reduced collagen content (GV-290.7 ± 41.7) compared with the water-treated roots (GI-328.3 ± 63.5) and those treated with NaOCl + EDTA (GII-333.9 ± 55.8). Roots irradiated with Er,Cr: YSGG laser also showed a higher inorganic/organic ratio (GV-9.5 ± 1.1) than roots treated with water (GI-7.7 ± 1.5), NaOCl + EDTA (GII-8.0 ± 1.4) and diode laser (GIII-8.2 ± 1.6). Both organic and inorganic contents increased from cervical to apical thirds in all groups. None of the surface treatments were able to promote changes in the inorganic content of the root dentin; treatment with NaOCl + EDTA combined with Er,Cr: YSGG altered collagen. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the effectiveness of dual wavelength (2780 nm Er,Cr:YSGG, 940 nm diode) laser in elimination of smear layer comparing it with Er,Cr:YSGG laser in terms of radicular dentin permeability and ultrastructural changes of root canal walls. Fifty-one sound single-rooted extracted teeth were instrumented up to size F4 and divided into three groups: group Co, non-irradiated samples; group A, irradiated with Er,Cr:YSGG laser; group B, irradiated with the dual wavelength laser. Afterward, the roots were made externally impermeable, filled with 2% methylene blue dye, divided horizontally into three segments reflecting the cervical, middle, and apical thirds then examined under microscope. Using analytical software, the root section area and dye penetration area were measured, and then, the percentage of net dye penetration area was calculated. Additionally, scanning electron microscope investigations were accomplished. Analysis of variance (ANOVA) showed significant differences between all groups over the three root thirds. Dye permeation in dual wavelength laser group was significantly higher over the whole root length: cervical, middle, and apical compared to Er,Cr:YSGG laser group and non-irradiated samples (p < 0.001). Scanning electron micrographs of dual wavelength irradiated samples showed a distinctive removal of smear layer with preservation of the annular structure of dentinal tubules. Er,Cr:YSGG laser root canal irradiation produced uneven removal of smear layer, in efficient cleanliness especially in the apical third. There was no sign of melting and carbonization. Within the studied parameters, root canal irradiation with dual wavelength laser increased dentin permeability. [ABSTRACT FROM AUTHOR]

The study aimed to evaluate the effect of various final irrigant activation protocols on push-out bond strength of fiber post. Thirty-two single-rooted human maxillar central teeth were sectioned below the cementoenamel junction, instrumented and obturated. Post-space preparation was performed, and roots were randomly divided into eight groups (n = 4) according to the final irrigant activation protocols; distilled water was used as an irrigant in group 1. The other groups were treated with 2.5% NaOCl and 17% EDTA. Conventional syringe irrigation (CSI, no activation) was used in group 2. Irrigation solutions were activated using passive ultrasonic irrigation (PUI, group 3), EndoVac apical negative pressure (ANP, group 4), diode laser (group 5), neodymium:yttrium-aluminum-garnet (Nd:YAG) laser (group 6), erbium:yttrium-aluminum-garnet (Er:YAG) laser (group 7), and Er:YAG laser using with photon-induced photoacoustic streaming (PIPS™) technique (group 8). In all groups, fiber posts (White Post DC, FGM) were luted using Panavia F 2.0 (Kuraray, Osaka, Japan). The specimens were transversally sectioned, and all slices from coronal and apical regions were subjected to push-out tests. The data were calculated as megapascals and analyzed by using two-way analysis of variance followed by post hoc Tukey honestly significant difference (HSD) tests. Removing the smear layer increased the bond strength to dentine when compared with the control group (p < 0.05). The highest bond strength was obtained in the PIPS laser-activated irrigation group (p < 0.05). Coronal root region presented significantly higher bond strength than the apical region (p < 0.05). PIPS laser-activated irrigation showed higher efficiency as a final irrigant activation protocol on push-out bond strength of fiber post. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the effect of two different laser systems on the mineral content of root canal dentin. Thirty-six single canal-extracted mandibular premolars were used in this study. The teeth were randomly divided into two groups of 18 teeth each and prepared with a master apical file #50. Dentin chips were obtained by Gates-Glidden burs and saved in Eppendorf tubes to serve as a control. Then, root canals were treated with a erbium:yttrium-aluminum-garnet or neodymium:yttrium-aluminum-garnet laser. Dentin chips were again obtained using Gates-Glidden. The levels of calcium (Ca), phosphorus (P), magnesium (Mg), sodium (Na), and potassium (K) in each specimen were measured by inductively coupled plasma-atomic emission spectrometry. Data were statistically analyzed by a Mann-Whitney U test. The changes in Ca, P, Mg, Ca, and K levels and the Ca/P ratio after laser irradiations were minimal and statistically not significant ( p > 0.05). It was determined that the laser systems used in this study did not affect the mineral content of root canal dentin. [ABSTRACT FROM AUTHOR]

The purpose of this study was to evaluate the surface and intrapulpal temperatures after treatments with different bleaching gels subjected to different types of light activation. A K-type thermocouple and infrared thermometer were used to measure the temperature increase during the 15- or 30-min treatment period. Light-emitting diode with a center wavelength of 405 nm (LED405), organic light-emitting diode (OLED), and femtosecond laser were tested and compared to ZOOM2. The tooth surface was treated with five bleaching agents and Vaseline which served as a control.The generalized estimating equation (GEE) model was applied for testing the differences in temperature increase. The ZOOM2 light source led to the largest increase in mean pulpal and tooth surface temperatures of 21.1 and 22.8 °C, followed by focused femtosecond laser which increased the pulpal and surface temperatures by up to 15.7 and 16.8 °C. Treatments with unfocused femtosecond laser, LED405, and OLED induced significantly lower mean temperature increases ( p < 0.001 for each comparison with ZOOM2 and focused femtosecond laser), both in the pulp chamber (up to 2.7, 2.5, and 1.4 °C) and at the tooth surface (up to 3.2, 3.4, and 1.8 °C). Significant differences between pulp chamber and tooth surface measurements were obtained for all types of bleaching gel, during treatments with ZOOM2 ( p < 0.001), LED405 ( p < 0.001), and unfocused ( p < 0.001) and focused femtosecond laser ( p ≤ 0.002). Different bleaching agents or Vaseline can serve as an isolating layer. Focused femtosecond laser and ZOOM2 produced large temperature increases in the pulp chamber and at the tooth surface. Caution is advised when using these types of light activation, while LED405, OLED, and unfocused femtosecond laser could be safely used. [ABSTRACT FROM AUTHOR]

Cleaning and disinfection of the root canal system are some of the most important goals in endodontic therapy. The aim of this preliminary study is to assess the effectiveness of Er:YAG laser fiber in removing the smear layer produced during root canal walls instrumentation. Forty-eight single-rooted teeth were prepared with manual and rotary Ni-Ti instruments, in addition to 2.5 % NaOCl irrigation. Samples were randomly subdivided into groups and treated with: three irradiations of 5 s each, with 300-μm Er:YAG endodontic fiber, 1 W and 2.5 % NaOCl solution (A Group); two laser irradiations with 17 % EDTA solution and 2.5 % NaOCl solution (B Group); laser irradiation plus 17 % EDTA solution and 2.5 % NaOCl (C Group); only in the final wash of 17 % EDTA (control group D). During laser treatment, temperature variations were analyzed by using thermocouple and thermal camera devices in order to test both deep and superficial temperatures. Each sample was finally observed by scanning electron microscope (SEM) at the coronal, medium, and apical thirds at ×500 magnification and blindly scored depending on the amount of smear layer. Statistical analysis of the results was conducted using the Kruskal-Wallis and Mann-Whitney test to determine the eventual significant differences between the quantity of smear layer in each group and between the groups at coronal, medium, and apical third: a p value <0.05 was considered significant. The thermal analysis realized by thermocouple with the used parameters demonstrated that laser endodontic fiber produces an average deep temperature increase of 3.5 ± 0.4 °C; analysis performed with a thermal camera showed an average superficial temperature increase of 1.3 ± 0.2 °C produced by laser endodontic fiber use. Deep and superficial temperatures fall immediately after irradiation possibly without causing structural damage or anatomical alteration inside the root canal and neither on periodontal tissues. SEM analysis showed that specimens of group B had the highest level of cleaning in every third, with a significant difference with groups D and A; group C samples showed a good percentage of cleaned tubules in apical and middle thirds, while group D teeth showed open dentinal tubules in coronal third, with a statistical difference with group A samples which were the worst cleaned. The Er:YAG fiber double irradiation with EDTA 17 % and NaOCl 2.5 % has been demonstrated to be effective in removing smear layer, even in the apical third which is described as the hardest area to clean during endodontic treatment. [ABSTRACT FROM AUTHOR]

The effects of Nd:YAG laser irradiations at different power settings on several oral pathogens were evaluated. A total of 252 dentin samples were divided into seven groups consisting of 36 dentin specimens each. In each group, 9 of the 36 specimens were used as controls, thereby including a control in every group. The remaining 27 specimens were divided into three subgroups consisting of nine specimens according to different Nd:YAG laser settings (1.5, 1.8, and 2 W). Each group was inoculated on the nonpulpal side with one of the following microorganisms: Candida glabrata, Candida tropicalis, Candida krusei, Candida sake, Candida lusitaniae, Candida kefyr, and Rhodotorula mucilaginosa. The following irradiation procedure was used: the specimens were irradiated on the bacteria-free side (the side consisting of the pulpal wall) using contact mode under the constant scanning movement of the optical fiber at an angle of 10°. One lasing cycle consisted of four irradiation cycles of 10 s each, with 15-s intervals in between each irradiation cycle. The remainder of the controls and the lased specimens of each group were prepared for the microbiological investigation. After incubation for 24 h at 37 °C, the colonies were counted, and the total number of surviving microorganisms was statistically assessed. Microorganisms irradiated with Nd:YAG laser at power settings 2 W, 15 pps did not survive. Although there was a significant reduction of microorganisms at 1.5 and 1.8 W, when comparing Nd:YAG laser irradiation with the control group, sterilization did not occur. [ABSTRACT FROM AUTHOR]

This study aimed to assess in vitro thermal alterations taking place during the Er:YAG laser cavity preparation of primary tooth enamel at different energies and pulse repetition rates. Forty healthy human primary molars were bisected in a mesio-distal direction, thus providing 80 fragments. Two small orifices were made on the dentin surface to which type K thermocouples were attached. The fragments were individually fixed with wax in a cylindrical Plexiglass® abutment and randomly assigned to eight groups, according to the laser parameters ( n = 10): G1 - 250 mJ/ 3 Hz, G2 - 250 mJ/ 4 Hz, G3 - 250 mJ/ 6 Hz, G4 - 250 mJ/10 Hz, G5 - 250 mJ/ 15 Hz, G6 - 300 mJ/ 3 Hz, G7 - 300 mJ/ 4 Hz and G8 - 300 mJ/ 6 Hz. An area of 4 mm was delimited. Cavities were done (2 mm long × 2 mm wide × 1 mm thick) using non-contact (12 mm) and focused mode. Temperature values were registered from the start of laser irradiation until the end of cavity preparation. Data were analyzed by one-way ANOVA and Tukey test ( p ≤ 0.05). Groups G1, G2, G6, and G7 were statistically similar and furnished the lowest mean values of temperature rise. The set 250 mJ/10 and 15 Hz yielded the highest temperature values. The sets 250 and 300 mJ and 6 Hz provided temperatures with mean values below the acceptable critical value, suggesting that these parameters ablate the primary tooth enamel. Moreover, the temperature elevation was directly related to the increase in the employed pulse repetition rates. In addition, there was no direct correlation between temperature rise and energy density. Therefore, it is important to use a lower pulse frequency, such as 300 mJ and 6 Hz, during cavity preparation in pediatric patients. [ABSTRACT FROM AUTHOR]

Although some studies claim to the increase of composite resin adhesion to Er:YAG-laser-treated dentin, there are still no reports on the adhesion of composite resin cements to the irradiated surface. This in vitro study evaluated the tensile bond strength (TBS) of a composite resin cement to dentin treated with the Er:YAG laser. Sixty human dentin samples were divided into four groups (n = 15): G1 (Control)-no treatment; G2-Er:YAG laser 60 mJ, 2 Hz, with water cooling, non-contact (19 J/cm(2)); G3-Er:YAG laser 60 mJ, 10 Hz, 50/10 fiber, contact, without water cooling (40 J/cm(2)); G4-Er:YAG laser 60 mJ, 10 Hz, 50/10 fiber, contact, with water cooling (40 J/cm(2)). After the surface treatment, each sample was submitted to bonding procedures. The analysis of variance (ANOVA) and Tukey tests revealed no statistical significant difference on TBS values for groups G1 (13.73 +/- 3.05 MPa), G2 (12.60 +/- 2.09 MPa) and G4 (11.17 +/- 4.04 MPa). G4 was not statistically different from G3 (8.64 +/- 2.06 MPa). Er:YAG laser irradiation with different settings can constitute an alternative tool to the use of composite resin-luting cements. [ABSTRACT FROM AUTHOR]