Search

One of the most important properties of membranes is their permeability to water and other small molecules. A targeted change in permeability allows the passage of molecules to be controlled. Vesicles made of membranes with low water permeability are preferable for drug delivery, for example, because they are more stable and maintain the drug concentration inside. This study reports on the very low water permeability of pure protein membranes composed of a bilayer of the amphiphilic protein hydrophobin HFBI. Using a droplet interface bilayer setup, we demonstrate that HFBI bilayers are essentially impermeable to water. HFBI bilayers withstand far larger osmotic pressures than lipid membranes. Only by disturbing the packing of the proteins in the HFBI bilayer is a measurable water permeability induced. To investigate possible molecular mechanisms causing the near-zero permeability, we used all-atom molecular dynamics simulations of various HFBI bilayer models. The simulations suggest that the experimental HFBI bilayer permeability is compatible neither with a lateral honeycomb structure, as found for HFBI monolayers, nor with a residual oil layer within the bilayer or with a disordered lateral packing similar to the packing in lipid bilayers. These results suggest that the low permeabilities of HFBI and lipid bilayers rely on different mechanisms. With their extremely low but adaptable permeability and high stability, HFBI membranes could be used as an osmotic pressure-insensitive barrier in situations where lipid membranes fail such as desalination membranes.

Class II hydrophobins are amphiphilic proteins produced by filamentous fungi. One of their typical features is the tendency to accumulate at the interface between an aqueous phase and a hydrophobic phase, such as the air–water interface. The kinetics of the interfacial self-assembly of wild-type hydrophobins HFBI and HFBII and some of their engineered variants at the air–water interface were measured by monitoring the accumulated mass at the interface via nondestructive ellipsometry measurements. The resulting mass vs time curves revealed unusual kinetics for a monolayer formation that did not follow a typical Langmuir-type of behavior but had a rather coverage-independent rate instead. Typically, the full surface coverage was obtained at masses corresponding to a monolayer. The formation of multilayers was not observed. Atomic force microscopy revealed formation and growth of non-fusing protein clusters at the interface. The mechanism of the adsorption was studied by varying the structure or charges of the protein or the ionic strength of the subphase, revealing that the lateral interactions between the hydrophobins play a role in their interfacial assembly. Additionally, a theoretical model was introduced to identify the underlying mechanism of the unconventional adsorption kinetics.

Hydrophobins are a family of small-sized proteins featuring a distinct hydrophobic patch on the protein’s surface, rendering them amphiphilic. This particularity allows hydrophobins to self-assemble into monolayers at any hydrophilic/hydrophobic interface. Moreover, stable pure protein bilayers can be created from two interfacial hydrophobin monolayers by contacting either their hydrophobic or their hydrophilic sides. In this study, this is achieved via a microfluidic approach, in which also the bilayers’ adhesion energy can be determined. This enables us to study the origin of the adhesion of hydrophobic and hydrophilic core bilayers made from the class II hydrophobins HFBI and HFBII. Using different fluid media in this setup and introducing genetically modified variants of the HFBI molecule, the different force contributions to the adhesion of the bilayer sheets are studied. It was found that in the hydrophilic contact situation, the adhesive interaction was higher than that in the hydrophobic contact situation and could be even enhanced by reducing the contributions of electrostatic interactions. This effect indicates that the van der Waals interaction is the dominant contribution that explains the stability of the observed bilayers.

Mesoporous γ-alumina is used as an adsorbent in the decontamination of water from heavy metals (e.g., nickel and cobalt) and as a support for heterogeneous catalysts prepared by impregnation. In these cases, alumina extrudates are in contact with aqueous solutions containing precursors of the active metal phase to be deposited. The proton concentration (or pH) in the metal solution in contact with alumina can impact the adsorption efficiency of decontamination processes and the activities of catalysts. Yet, it is difficult to quantify the effect of the pH inside the pores since protons are not detected by classical imaging techniques. In this article, the effect of protons on nickel adsorption on alumina is evaluated using a novel technique coupling liquid analysis (pH, conductivity, and UV/vis) and laser-induced breakdown spectroscopy (or LIBS) analysis of concentration gradients inside the solid. Both methods are in excellent agreement. The results show a slow diffusion of protons inside alumina pores (diffusion continues even after 940 min), yielding high proton concentration gradients. On the other hand, the nickel species penetrate the extrudates faster but are slowly displaced by protons under certain operating conditions. As a result, different metal concentration profiles are obtained, depending on the initial pH and contact time. These findings are interesting in catalysis since they prove the possibility of controlling the deposition of the active metal on catalysts by regulating the operating conditions of impregnation. For typical industrial impregnation times (a few minutes to 1 to 2 h), protons do not have enough time to deeply penetrate inside extrudates, so the initial pH of the metal solution will have nearly no effect on the metal distribution. Conversely, decontamination processes have much longer contact times; therefore, lower initial pH values should have negative impacts on the adsorption efficiency due to the protons displacing the adsorbed nickel.