Search

Terbium aluminum garnet (Tb3Al5O12, TAG) ceramics have become a promising magneto‐optical material owing to the outstanding comprehensive performance, including the magneto‐optical, thermal, and mechanical properties. Fine‐grained TAG ceramics with high optical quality and mechanical properties have attracted much attention. In this study, TAG ceramics with fine grains and high optical quality are fabricated successfully by a two‐step sintering method from co‐precipitated nano‐powders. After pre‐sintered at 1525°C in vacuum and hot isostatic pressed at 1600°C, the in‐line transmittance of TAG ceramics reaches 81.8% at 1064 nm, and the average grain size is 7.1 μm. The Verdet constant of TAG ceramics is −179.6 ± 4.8 rad T−1 m−1 at 633 nm and −52.1 ± 1.9 rad T−1 m−1 at 1064 nm, higher than that of commercial Tb3Ga5O12 crystals. The thermal conductivity of TAG ceramics is determined from 25 to 450°C, and the result is 5.12 W m−1 K−1 at 25°C and 3.61 W m−1 K−1 at 450°C. A comparison of mechanical properties between large‐ and fine‐grained TAG ceramics fabricated under different conditions is conducted. The fine‐grained TAG ceramics possess a bending strength of 226.3 ± 16.4 MPa, which is 9.7% higher than that of the large‐grained ceramics. These results indicate that reducing the grain size on the premise of high optical quality helps improve the comprehensive performance of TAG ceramics. [ABSTRACT FROM AUTHOR]

In order to fully pump and smoothen the temperature gradient of the gain medium, multistage gradient doping Yb:YAG laser ceramics were designed. The composite green bodies were fabricated by tape casting, and multistage gradient doping Yb:YAG ceramics with high optical quality were prepared by vacuum sintering and hot isostatic pressing. For samples pre‐sintered at 1740°C for 30 h and then HIP‐ed at 1700°C for 3 h in argon at 200 MPa, the in‐line transmission values at 1100 nm of YAG, 0.6 at.%Yb:YAG, and 1.5 at.%Yb:YAG ceramics were found to be 83.9%, 84.1%, and 83.3%, respectively. Finally, the 940 nm laser diode was used as the pump source to realize the 1030 nm laser output of multistage gradient doping Yb:YAG ceramic slab with a total energy of 3.43 J. The corresponding optical‐to‐optical conversion and slope efficiencies were 30% and 45%. [ABSTRACT FROM AUTHOR]

0.5 at.% Cr:ZnGa2O4 precursor was synthesized by the co‐precipitation method with nitrates as raw materials, using ammonium carbonate as the precipitant. Low‐agglomerated Cr:ZnGa2O4 powders with an average particle size of 43 nm were obtained by calcining the precursor at 900℃ for 4 h. Using the powders as starting materials, 0.5 at.% Cr:ZnGa2O4 ceramics with an average grain size of about 515 nm were prepared by presintering at 1150℃ for 5 h in air and HIP post‐treatment at 1100℃ for 3 h under 200 MPa Ar. The in‐line transmittance of 0.5 at.% Cr:ZnGa2O4 ceramics with a thickness of 1.3 mm reaches 59.5% at the wavelength of 700 nm. The Cr:ZnGa2O4 ceramics can be effectively excited by visible light and produce persistent luminescence at 700 nm. For Cr:ZnGa2O4 transparent ceramics, the brightness of afterglow was larger than 0.32 mcd/m2 after 30 min, which is far superior to that of Cr:ZnGa2O4 persistent luminescence powders. [ABSTRACT FROM AUTHOR]

Transparent terbium aluminum garnet (TAG) ceramics were achieved by the vacuum sintering plus HIP post‐treating from the coprecipitated TAG nanoparticles. The influences of vacuum sintering temperature and sintering aid TEOS on the optical quality of the TAG ceramics were studied. The results show that with the increase of sintering temperature, the optical quality of TAG ceramics is improved gradually, and the in‐line transmittance of the TAG ceramics treated at 1720°C for 20 hours under vacuum and then HIP post‐treated at 1700°C for 3 hours under 200 MPa argon gas is 81.6% at 1064 nm. The sintering additive TEOS can improve the optical quality of TAG ceramics and inhibit the valence state change of Tb3+ ions to Tb4+ during the annealing process. The Verdet constant of the TAG ceramics at 632.8 nm is about −178 rad·T−1·m−1 at room temperature, which is 1.3 times that of the commercial TGG crystals (−134 rad·T−1·m−1). [ABSTRACT FROM AUTHOR]

In this article, 5 at.% Yb:Lu2O3 transparent ceramics were fabricated by vacuum sintering combined with hot isostatic pressing (HIP) posttreatment using co‐precipitated nano‐powders. The influence of precipitant molar ratio, ammonium hydrogen carbonate, to metal ions (AHC/M3+, R value) on the properties of Yb:Lu2O3 precursors and calcined powders was investigated systematically. It was found that the powders with different R value calcined at 1100°C for 4 hours were pure cubic Lu2O3 but the morphologies of precursors and powders behaved differently. The opaque samples pre‐sintered at 1500°C for 2 hours grew into transparent ceramics after HIP posttreatment at 1750°C for 1 hour. The final ceramic with R = 4.8 showed the best optical quality with the in‐line transmittance of 79.7% at 1100 nm. The quasi‐CW laser operation was performed at 1034 nm and 1080 nm with a maximum output power up to 8.15 W as well as a corresponding slope efficiency of 58.4%. [ABSTRACT FROM AUTHOR]

The 0.05 at.% Co:MgAl2O4 precursor was synthesized by the coprecipitation method from a mixed solution of magnesium, aluminum, and cobalt nitrates using ammonium carbonate as the precipitant. 0.05 at.% Co:MgAl2O4 transparent ceramics were successfully obtained via vacuum sintering and hot isostatic pressing (HIP) of 0.05 at.% Co:MgAl2O4 nanopowder calcined at 1100°C for 4 hours. The properties of powder and ceramics were comprehensively investigated. X‐ray diffraction (XRD) results showed that Co:MgAl2O4 nanopowder had a pure spinel phase. Also, the in‐line transmittances of the HIP posttreated Co:MgAl2O4 ceramics with the thickness of 1.2 mm were 82% at 400 nm and 84.7% at 900 nm. The average grain sizes of 0.05 at.% Co:MgAl2O4 ceramics before and after the HIP posttreatment were 11 and 28 μm, respectively. The calculated ground state absorption cross section of 0.05 at.% Co:MgAl2O4 ceramics was 2.9 × 10−19 cm2, indicating that this ceramics is a promising material applied as a saturable absorber for passive laser Q‐switches in the 1.3‐1.7 μm domain. [ABSTRACT FROM AUTHOR]

Using the tape casting method combined with vacuum sintering and hot isostatic pressing, high‐quality planar waveguide YAG/10 at.%Yb:YAG/YAG ceramics were successfully prepared. For the sample presintered at 1750°C for 30 hours and then HIPed at 1700°C for 3 hours in 200 MPa argon, the in‐line transmittance reached 82.5% at 400 nm and the average grain size was ~17.1 μm. The diffusion behaviors of Yb ions across the contact boundary between the cladding YAG layer and the core Yb:YAG layer were determined by Fick's second law. Then, a 1030 nm continuous‐wave (CW) Yb:YAG planar waveguide ceramic laser based on the structure of master oscillator power amplification (MOPA) was realized. After a single‐pass amplification, the maximum output of the ceramic slab (60 × 10 × 1 mm3) reached 1251 W and the corresponding optical‐to‐optical efficiency was 30.0%, which is the highest output power of a Yb:YAG planar waveguide ceramic laser to the best of our knowledge. [ABSTRACT FROM AUTHOR]

Ho:Lu3Al5O12(Lu AG) transparent ceramics are potential 2 μm eye-safe laser materials. Polycrystalline 0.8 at.% Ho:Lu AG ceramics with high optical quality were successfully fabricated by solid-state reactive sintering of high-purity oxide powders. The microstructure, the optical transmission, the spectrum characteristic, and the laser performance were investigated in this paper. The average grain size of Ho:Lu AG ceramics vacuum sintered at 1830°C for 30 hour is about 14 μm. The in-line transmittance of the sample is measured to be 81.7% and 82.0% at 1000 and 2250 nm, respectively. The absorption and the emission cross sections are calculated to be 0.88 × 10−20 cm2 at 1906 nm and 1.26 × 10−20 cm2 at 2094 nm. Using a thulium-doped yttrium-lithium-fluoride (Tm: YLF) laser with the central wavelength of 1907.5 nm as the pump source, 2.67 W continuous wave ( CW) laser operation at 2100.74 nm was obtained with a slope efficiency of 26.5%. The beam quality factor M2 was calculated to be 1.1, which indicated nearly diffraction-limited beam propagation and the laser was the fundamental TEM00 Gaussian mode. [ABSTRACT FROM AUTHOR]