Search

First‐principles calculations were performed to reveal an effect of Ca vacancies on the stability of substitutional divalent cations M2+ (M = Mg, Zn, Sr) in Ca‐deficient hydroxyapatite (dHAp). M2+ concentrations up to 20 mol% in dHAp were considered, and the most stable substitutional sites and their lowest energy configurations in the dHAp lattice were examined with the aid of a generic algorithm method. It was found that defect formation energies of substitutional M2+ are lower in dHAp than in stoichiometric HAp (sHAp) at all M2+ concentrations. This indicates that these M2+ ions are more favorably involved in dHAp than in sHAp, which is in reasonable agreement with experiment. Detailed analyses on atomic structures in dHAp show that the presence of a Ca vacancy varies its surrounding Ca–O bond lengths over a wide area so that Ca–O polyhedrons with various sizes are produced. As a result, M2+ ions can predominantly occupy Ca sites at which M2+ fits better, depending on the ionic radii of M2+. For Zn2+ substitution in dHAp, its defect formation energy decreases more with the increasing concentrations and has the minimum value at 15 mol%. Such a trend can be understood from changes in effective coordination numbers of Zn in dHAp. [ABSTRACT FROM AUTHOR]

Rapid densification of ceramics has been realized and its merits were demonstrated through multiple approaches out of which UHS and flash sintering attract recent attention. So far, however, scalability remains difficult. A rise in throughput and scalability is enabled by the introduction of blacklight sintering powered by novel light source technology. Intense illumination with photon energy above the bandgap (blacklight) allows high absorption efficiency and, hence, very rapid, contactless heating for all ceramics. While heating the ceramic directly with light without any furnace promises scalability, it simultaneously offers highly accurate process control. For the technology transfer to industry, attainable material quality needs to be assured. Here, we demonstrate the excellent microstructure quality of blacklight‐sintered ceramics observed with ultrahigh voltage electron microscopy revealing an option to tune nanoporosity. Moreover, we confirm that electronic, electron, oxygen, and lithium‐ion conductivities are equal to conventionally sintered ceramics. This gives the prospect of transmitting the merits of rapid densification to the scale of industrial kilns. [ABSTRACT FROM AUTHOR]

Alumina bicrystals with low-angle and near-Σ3 <0001> tilt grain boundaries were fabricated using diffusion bonding to study the dislocation structures in alumina grain boundaries. The resulting grain-boundary structures were investigated using high-resolution transmission electron microscopy, and the grain-boundary energies were analyzed using theoretical calculations. It was found that partial dislocations with Burg-vectors of the type 1/3<10&1macr;0> were periodically located in ers the boundaries and that a stacking fault between pairs of partials was formed in such boundaries. The length of the stacking fault decreased with increased misorientation angles, which was reasonably predicted by the theoretical calculation. In the case of a near-Σ3 grain boundary, an array of displacement shift complete dislocations with the Burgers vector of 1/3 was periodically formed along the boundaries. These boundaries did not have stacking faults. The spacing between the dislocations decreased with increased deviation angle from the exact-Σ3 boundary with the tilt angle of 60°. [ABSTRACT FROM AUTHOR]

Rapid densification of ceramics has been realized and its merits were demonstrated through multiple approaches out of which UHS and flash sintering attract recent attention. So far, however, scalability remains difficult. A rise in throughput and scalability is enabled by the introduction of blacklight sintering powered by novel light source technology. Intense illumination with photon energy above the bandgap (blacklight) allows high absorption efficiency and, hence, very rapid, contactless heating for all ceramics. While heating the ceramic directly with light without any furnace promises scalability, it simultaneously offers highly accurate process control. For the technology transfer to industry, attainable material quality needs to be assured. Here, we demonstrate the excellent microstructure quality of blacklight‐sintered ceramics observed with ultrahigh voltage electron microscopy revealing an option to tune nanoporosity. Moreover, we confirm that electronic, electron, oxygen, and lithium‐ion conductivities are equal to conventionally sintered ceramics. This gives the prospect of transmitting the merits of rapid densification to the scale of industrial kilns. [ABSTRACT FROM AUTHOR]