Search

As one of the important electronic components, the dielectric capacitors for energy storage applications have been extensively studied in recent years. Among various dielectric materials, the perovskite oxide Bi0.5Na0.5TiO3‐based ceramics have become promising candidates due to their high polarization, dielectric tunability, environment‐friendly composition, and so forth. Herein, the relaxor ferroelectric ceramics of Bi0.5Na0.5TiO3–SrTiO3–Bi(Mg0.5Zr0.5)O3 were prepared via solid‐state reaction method. The sample with optimal composition not only retains the high polarization by introducing Bi3+ ions, but also achieves the reduced remanent polarization by enhancing relaxor behavior and the promoted electric breakdown strength by the grain size refinement. Accordingly, a high recoverable energy density of 8.3 J/cm3 under 450 kV/cm and the superb charge/discharge properties (current density CD = 1200 A/cm2, power density PD = 150 MW/cm3, charge/discharge time t0.9 = 0.15 µs) are achieved, revealing great prospect in energy storage applications. [ABSTRACT FROM AUTHOR]

Achieving comprehensive improvement in both piezoelectric coefficient (d33) and mechanical quality factor (Qm) has become a key issue in the research of high‐power piezoelectric ceramics. Here, we focused on Mn‐doped Pb(In1/2Nb1/2)O3‐Pb(Sc1/2Nb1/2)O3‐PbTiO3 (PIN‐PSN‐PT) relaxor ferroelectric ceramics, where Mn‐doping is employed to enhance Qm. The effects of doping concentration and PT content on phase structure, ferroelectric, dielectric, and electromechanical properties were systematically studied. The well radius matching between Mn ions and B‐site ions facilitates the ion substitution and significantly increases the concentration of oxygen vacancies, thereby enhancing the domain wall pinning effect. A significantly weakened mutual constraint relationship between d33 and Qm is observed in the 2 mol% Mn‐doped PIN‐PSN‐PT ceramics with tetragonal phase, which exhibits Qm exceeding 3000 while maintaining d33 higher than 320 pC/N and Curie temperature higher than 300°C, leading to the vibration velocity over 1.15 m/s. Rayleigh analysis reveals the higher intrinsic piezoelectric response in high PT components compared to that in low PT components, which was thought to be the origin for the weakened mutual constraint relationship between d33 and Qm in tetragonal Mn‐doped PIN‐PSN‐PT ceramics. [ABSTRACT FROM AUTHOR]

Textured piezoelectric ceramics, such as textured Pb(Mg1/3Nb2/3)O3‐PbTiO3 (PMN‐PT) ceramics, have attracted considerable attention from both academia and industry, as they possess crystal‐like piezoelectric properties, high composition homogeneity, and low manufacturing cost. However, the main difficulty with the textured piezoelectric ceramics is the presence of BaTiO3 (BT) templates, which greatly reduces their piezoelectricity and phase transition temperature. Thus, it is highly recommended to fabricate textured piezoelectric ceramics using as few templates as possible. Here, we successfully fabricated high‐quality <001>‐textured PMN‐28PT ceramics (texturing degree of 99%) by using an extremely small amount of BT templates (1 vol.%) with the help of CuO/B2O3 sintering aids. The textured PMN‐28PT ceramic exhibits 80% piezoelectric coefficient (d33 ∼ 1200 pC/N), 96% electromechanical coefficient (k33 ∼ 88%) and the same temperature stability (Trt ∼ 100, Tc ∼ 150°C) when compared to its single crystal counterpart. In addition, by using an alternating current electric field poling (AC‐poling), the piezoelectric coefficient d33 and dielectric permittivity ε33 of the textured PMN‐28PT ceramics were further enhanced around 5–8%. It is believed that the advantages of high electromechanical properties, low cost, and easy mass production of textured PMN‐28PT ceramic will make it a promising candidate for advanced electromechanical devices. [ABSTRACT FROM AUTHOR]

Cold sintered, Li2MoO4‐based ceramics have recently been touted as candidates for electronic packaging and low temperature co‐fired ceramic (LTCC) technology but MoO3 is an expensive and endangered raw material, not suited for large scale commercialization. Here, we present cold sintered temperature‐stable composites based on LiMgPO4 (LMP) in which the Mo (and Li) concentration has been reduced, thereby significantly decreasing raw material costs. Optimum compositions, 0.5LMP‐0.1CaTiO3‐0.4K2MoO4 (LMP‐CTO‐KMO), achieved 97% density at <300°C and 600 MPa for 60 minutes. Raman spectroscopy, X‐ray diffraction, scanning electron microscopy, and energy dispersive X‐ray mapping confirmed the coexistence of end‐members, LMP, CTO, and KMO, with no interdiffusion and parasitic phases. Composites exhibited temperature coefficient of resonant frequency ~ –6 ppm/°C, relative permittivity ~9.1, and Q × f values ~8500 GHz, properties suitable for LTCC technology and competitive with commercial incumbents. [ABSTRACT FROM AUTHOR]

BaTiO3 ( BTO) nanofibers were fabricated by sol-gel combined with electrospinning method. The effects of the concentration of acetic acid and sintering temperatures on the crystal phase and microstructure of the samples were investigated by scanning electron microscopy, X-ray diffraction, and transmission electron microscopy ( TEM). BTO nanofibers with improved surface morphology were obtained as the ethanol to acetic acid ratio (E/A) was 8:3. The fibers calcined at 750°C for 2 h exhibited good morphology and crystallization. TEM studies revealed that the BTO nanofibers were polycrystalline, with diameters being on the order of hundreds nanometer, where the existence of domains offered proof of ferroelectric structure. The ferroelectric domains and piezoresponse of BTO nanofibers were characterized by piezoresponse force microscopy. The calculated d33 was 20 pm/V at maximum strain amplitude. [ABSTRACT FROM AUTHOR]

As one of the important electronic components, the dielectric capacitors for energy storage applications have been extensively studied in recent years. Among various dielectric materials, the perovskite oxide Bi0.5Na0.5TiO3‐based ceramics have become promising candidates due to their high polarization, dielectric tunability, environment‐friendly composition, and so forth. Herein, the relaxor ferroelectric ceramics of Bi0.5Na0.5TiO3–SrTiO3–Bi(Mg0.5Zr0.5)O3 were prepared via solid‐state reaction method. The sample with optimal composition not only retains the high polarization by introducing Bi3+ ions, but also achieves the reduced remanent polarization by enhancing relaxor behavior and the promoted electric breakdown strength by the grain size refinement. Accordingly, a high recoverable energy density of 8.3 J/cm3 under 450 kV/cm and the superb charge/discharge properties (current density CD = 1200 A/cm2, power density PD = 150 MW/cm3, charge/discharge time t0.9 = 0.15 µs) are achieved, revealing great prospect in energy storage applications. [ABSTRACT FROM AUTHOR]