Search

Statement of Problem: Polymer-based computer-aided design and computer-aided manufacturing (CAD-CAM) materials have either a high content of ceramic filler particles or a ceramic network structure. Proper etching of these materials is challenging. Therefore, it is relevant to assess different surface etching strategies and morphological alterations as a result of these techniques., Purpose: The purpose of this 2-part in vitro study was to evaluate different etching strategies on the surface roughness and its relationship to the surface contact angle with a subsequent morphological characterization of different CAD-CAM materials., Material and Methods: Two CAD-CAM polymer-based materials and 1 CAD-CAM ceramic material were selected for this study. The materials were treated with different strategies, including a combination of airborne-particle abrasion and an application of 9% hydrofluoric acid etching. After the surface treatment, roughness measurements (Sa) were assessed by using an optical profilometer on an area of 1.47 mm 2 . Subsequently, the contact angle on the surface was examined by means of the sessile drop technique and an optical contact angle meter. The data were analyzed by using a 2-way analysis of variance, the post hoc Tukey test (α=.05), and the Pearson correlation coefficient., Results: The 3 materials tested showed an increase in surface roughness when treated with surface airborne-particle abrasion. However, the materials with polymer in their composition concomitantly increased the contact angle. More hydrophilic surfaces were observed when hydrofluoric acid was applied, regardless of the composition of the materials. The surface roughness presented a strong positive linear tendency in the surface treatments used., Conclusions: The application of airborne-particle abrasion on the surface of the polymer-based CAD-CAM materials increased the roughness and contact angle. However, the application of acid etching after the airborne-particle abrasion decreased the contact angle for polymer-based CAD-CAM materials, resulting in considerable enhancement of the surface quality for proper bonding., (Copyright © 2021 Editorial Council for The Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Statement of Problem: Bonding to recently launched polymer-based computer-aided design and computer-aided manufacturing (CAD-CAM) materials has been challenging. Evidence regarding etching strategies for dual-phase CAD-CAM materials is sparse, but adequate bonding is crucial for the clinical success and longevity of a restoration., Purpose: The purpose of this 2-part in vitro study was to evaluate and compare the effect of surface treatment strategies on the microshear bond strength and work of adhesion of polymer-based and ceramic materials. In addition, chemical elements present on the surface and the interface morphology after using those strategies were also assessed., Materials and Methods: Two CAD-CAM polymer and 1 CAD-CAM ceramic materials were selected for this in vitro study. The materials were subjected to different surface treatment strategies, including airborne-particle abrasion and the application of 9% hydrofluoric acid. Specimens were submitted to microshear bond strength before and after thermocycling, and the failure mode was classified. The work of adhesion was calculated based on the water-to-air surface tension of 72.8 mN.m -1 and the Young- Dupré equation. The surfaces were submitted to energy-dispersive X-ray spectroscopy, and the interfaces were analyzed using a scanning electron microscope. Data were subjected to 2-way ANOVA and the Tukey post hoc test (α=.05)., Results: The highest microshear bond strength means were observed for the polymer-based materials when hydrofluoric acid or airborne-particle abrasion was applied. The 3 materials tested showed a decrease in microshear bond strength after thermocycling, except for applying airborne-particle abrasion to 1 of the polymer-based material tested. The ceramic material tested showed a high microshear bond strength with the application of airborne-particle abrasion and hydrofluoric acid combined. The work of adhesion varied across the materials and presented high means when hydrofluoric acid was used., Conclusions: A combination of airborne-particle abrasion plus hydrofluoric acid should be considered for polymer-based or feldspathic ceramic CAD-CAM materials. In this in vitro study, both etching procedures combined produced higher bonding values for all materials tested., (Copyright © 2021 Editorial Council for The Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Statement of Problem: The influence of different glaze firing protocols and cooling on the behavior of computer-aided design and computer-aided manufacturing (CAD-CAM) ceramics is unclear., Purpose: The purpose of this in vitro study was to investigate the influence of different glaze firing protocols on the abrasion resistance, surface roughness, microhardness, and brittleness index of CAD-CAM ceramics., Material and Methods: Rectangular specimens of IPS e.max CAD (MAX), IPS Empress CAD (PRE), and CEREC Blocs (CER) were obtained and divided into 5 groups according to the glaze firing protocol (n=8): control (CO), 1 conventional glaze firing (GF), 2 conventional glaze firings (GF 2 ), 1 extended glaze firing (EG), and 2 extended glaze firings (EG 2 ). The coefficient of friction (μ) was determined with the pin-on-disk test, and specimens were analyzed with an optical interferometer to calculate volume loss and roughness. Vickers microhardness and the brittleness index were obtained with a microdurometer. Microhardness data were evaluated by 2-way ANOVA and the Sidak tests (α=.05). Data from other tests were assessed with nonparametric ANOVA and Bonferroni tests (α=.05)., Results: Groups GF 2 , EG, and EG 2 of MAX and PRE and all groups of CER presented higher levels of coefficient of friction. Groups EG and EG 2 of MAX and CER showed high volume loss and surface roughness. Groups EG and EG 2 of MAX and PRE showed lower hardness, as did all groups of CER. MAX-CO and groups GF and EG of PRE showed a lower brittleness index (P<.05), while CER groups showed no significant differences (P>.05)., Conclusions: Ceramic specimens with conventional glaze firing presented less surface wear than those with extended glaze firing. The number of firings did not have a statistically significant influence., (Copyright © 2022 Editorial Council for The Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Statement of Problem: The post space must be prepared with techniques that do not interfere with the bond strength. These techniques are related to the availability of opened dentinal tubules and incidence of residue among the dentin, the adhesive, and the cement. Nevertheless, the effect of different irrigants during endodontic instrumentation is unclear., Purpose: The purpose of this in vitro study was to assess the incidence of residue, the number of opened dentinal tubules, and the bond strength of the cementation system to root dentin of post space after 3 different irrigation protocols., Material and Methods: The roots of bovine incisors were obturated, prepared to receive a fiber post, and divided into 3 groups as per the irrigation protocol: without irrigation, with alternating irrigation, and with continuous irrigation. Thirty roots (n=10) were evaluated by using scanning electron microscopy to assess the incidence of residue (×100 magnification) and the number of opened dentinal tubules (×2000 magnification). The fiber posts were cemented, and the remaining specimens (n=10) were subjected to pushout testing and failure mode evaluation., Results: All protocols presented a similar incidence of residue, regardless of the post space third (P>.05). The irrigation protocol without irrigation had the lowest number of opened dentinal tubules in the cervical and middle thirds (P<.05). The number of opened dentinal tubules was similar in all protocols in the apical third of the post space (P>.05). The irrigation protocol without irrigation had the lowest bond strength values in the cervical and middle thirds (P<.05). The irrigation protocol with continuous irrigation had the highest bond strength values in the apical third (P<.05)., Conclusions: Post space preparation without irrigation negatively affected the bond strength of the resin cementation system to root dentin., (Copyright © 2020 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)