Search

This paper present product design and development of waste paper plastering mortars machine. This waste paper plastering mortar is manual machine system. The main element to make mortar is cement, sand, water and waste paper. These machines have two separate tanks, which is the first tank is to produce a pulp and second tank is to mix up the entire ingredient. The objectives of this research are to design a Waste paper plastering machine, to develop a functional prototype of Waste Paper Plastering Machine and also to test the machine by compare the best method by with machine and without machine to make plastering mortar. The testing has been done between preparation and procedure how to make plastering mortar with machine and without machine. This machine can be used in every household. This can save environment and reduce pollution.

Paper and plant extracts are materials that are cheap and easy to find everywhere, have great potential to be used as a portable, low-cost and biodegradable label for the application of chemical compounds detection. In this paper, we have explored potential methods for the label to detect ammonia gas, an indicator of meat spoilage, with the colorimetric principle. By immersing paper with plant extracts that are sensitive to ammonia, in this case, is anthocyanin from Ruellia simplex flower extract, the detection of ammonia at various concentrations can be achieved. Ammonia concentration used is 0; 0.005%; 0.025%; 0.1%, 0.25% and 0.5%. Color change images on the label when detection is scanned by a flatbed scanner. ImageJ software is used to quantify the color changes. Ammonia detection at various concentrations results in a color change from red to yellow on the paper label. Paper-based labels with discoloration that can be captured visually by the consumer’s eyes are considered as promising approaches to determine the freshness of meat.

Kidney failure is a degenerative disease that has a prevalence of nearly 12 to 15% of the total population in the world. Renal scans are one of many diagnostic means which refers to several examinations using radiopharmaceuticals that evaluate the function and anatomy of the kidneys. Technetium-99m-diethylenetriaminepetaacetic acid ([99Tc]Tc-DTPA) is a commonly used radiopharmaceutical for kidney scans. Since the half-life of technetium-99m radioisotope, one component of this radiopharmaceutical, is only about 6.0 hours, so an efficient and effective quality control techniques is a necessity. Up to now, two-systems thin layer chromatography (TLC) is a common method used for radiochemical purity (RCP) test of [99mTc]Tc-DTPA. Recently one-system TLC has been successfully developed for this purpose. Therefore prior to its application, it is necessary to validate as well to compare this method with an established method (WHO Pharmacopoeia). These methods were two-system used Whatman-1 paper as static phase and methyl ethyl ketone (two-system-A) and 0.9% sodium chloride (two-system-B) as mobile phases and one-system used Whatman-1 paper as static phase and acetone: 0.9% sodium chloride (11:9) as a mobile phase. RCP of [99mTc]Tc-DTPA was then tested using these methods. The retrieved data were processed and validated with some variables like accuracy, precision, and compared using t-test to see whether the above-mentioned TLC systems show a significant difference or not. The analysis results of RCP test of [99mTc]Tc-DTPA using two-system method was 99.37± 0.48% while using one-system method was 99.20 ± 0.41%. The percentage accuracy of the data between two methods was 99.83%. The t-stat value for both methods was 0.84 so it can be concluded that the results of measurement using one-system method are not significantly different from two-system method.

When partial discharge occurs in the power transformer, the arc can further develop on the oil-paper interface between high and low potentials, and then form a path, resulting in large-area flashover. This will lead to a wide range of insulation damage, insulation failure, equipment shutdown and even large-scale economic losses. For the insulation damage caused by surface discharge of oil paper insulation, relevant scientific research institutions have carried out a large number of experimental studies. However, limited by the test conditions, the research focuses on the small-size model below 50mm, and mostly adopts the test device of uneven electric field. The research on the “large-size“ of the same scale inside the transformer is still blank. In this study, an oil-paper insulation surface discharge test platform with a large size of 50-150mm is built, the electric field conditions at the oil paper interface during the operation of transformers in engineering are simulated, and the surface discharge test of insulating paperboard is carried out by taking the same sample processing means as the engineering. Combined with the test results, a typical design optimization case of setting along surface corner ring to improve the allowable value of along surface discharge field and enhance along surface insulation margin is proposed. It lays a foundation for enriching the transformer oil-paper insulation design parameter system and improving the transformer oil paper insulation performance and operation reliability.

A tapered glass capillary MeV-ion microbeam setup, previously home-developed, was recently upgraded. To check the upgraded microbeam system quality and accuracy, microbeam particle induced X-ray emission (PIXE) mapping of potassium permanganate (KMnO4) solution diffusion in filter paper was carried out to study how the measured solvent diffusion followed the diffusion laws. Two initial boundary conditions and diffusion situations were applied: (1) the paper vertically placed in air with one end soaked in the solution for ten minutes, and (2) the paper horizontally placed on water with the solution dropped at a side of the paper for three minutes. 2-MeV-proton microbeam PIXE analyzed the paper pixel by pixel and the GUPIXWIN software was used to calculate the elemental concentrations in the pixels to map the concentration changes in the pixels as a function of the distance between the pixel position and the origin of the solution. The resulting maps demonstrated the solution diffusions in two cases indeed well following the diffusion laws, a steady-state diffusion dominated process where the elemental concentration was a linear function with the distance but joined by other non-diffusion factors for case 1, and a pure diffusion process where the elemental concentration was an error function with the distance for case 2.

The algorithm and the experience of implementing automated systems for monitoring the quality of waste in the pulp and paper industry in the framework of a unified system of industrial environmental control are being considered. The required list of wastewater parameters subject to automated control is determined. The main technical and operational characteristics of automated wastewater quality control instruments included in the unified state register of measuring instruments are being considered. The problems of introduction of automated wastewater quality control systems in the Russian Federation are being considered.

A method for detecting paper’s surface defects is proposed, which is based on mathematical morphology algorithm and computer vision technique. Firstly, the mean filtering and wavelet denoising in image pre-processing are used to eliminate the image noise, and wavelet analysis can achieve image enhancement and increase the contrast between the target area and the background. And then, an improved threshold Canny operator is used to segment the image to extract the complete scratch line and other defect edges. Finally, the target region features are coloured by mathematical morphology processing. The method’s stimulating result is verified in the Matlab software, from which we can conclude that the method’s detecting effect is very effective.

Sensors with accurate detection of various liquids have attracted increasing research interests in environmental protection and organic solvents transporation. In this paper, liquid sensor based on laser induced graphene paper (LIGP) was proposed, and successfully used for the rapid detection of micro volume liquid. The processing-structure-property relationship was systemically studied. LIGPs with different morphologies exhibited various sensitivities and showed good reproducibility and fast response. The response mechanism related to contact resistance between some adjacent graphene flakes/fibers was proposed. With the key findings, LIGP liquid sensors can be used as the detector for accurate identification of different solvents and have great potential in monitoring organic solvent leakages of pipelines and fabrication of smart anti-corrosion composite structures.

Kojic acid is an antioxidant used by the cosmetics industry but the excessive usage of kojic acid may cause harm to human health. Therefore, it is important to detect the content of kojic acid in cosmetic products. In this work, the low-cost and simple paper-based analytical devices (μPADs) based on double-sided adhesive tape were developed for the colorimetric detection of kojic acid. The μPADs were fabricated by dissolving double-sided adhesive tape in toluene and then making the patterned adhesive tape penetrate into the filer paper. Ferric nitrate was used as the reagent to react with kojic acid, and the product of their chelating reaction caused the color change from colorless to orange-red. The ImageJ software was used to analyze the color intensity and the corresponding correction curve was determined. The μPADs for the detection of kojic acid exhibited a wide linear range (0.05 - 4 mM) and the detectable limit was 0.05 mM. The good selectivity and reproducibility were also demonstrated.

Most papers are made from virgin wood-based pulp of hardwood sources but recently, softwood have received enormous attention as alternative to hard wood because the hardwood takes a significant number of years to mature enough for use in the pulp and paper industry unlike softwood which are majorly annual plants. The annual crop in focus in this work is the yellow open-pollinated variety of corn which generates tons of waste at harvest. A novel attempt is made to ascertain the viability of corn sheaths as raw material for the pulp and paper industry by carrying out a comprehensive analysis on the pulp and paper made from the pulp. The sheaths were dried, shred and cut into pieces suitable for the digester and the pulps obtained were analysed for physico-chemical properties. Hand sheets were also made using the generated pulp and its physico-mechanical properties were analysed. Results obtained were compared with pulp from corn husks from other parts of the country, three Nigerian fibre sources – silk cotton, bagasse and rice straw and other foreign non-wood sources and found to be of competitive properties. Pulp properties of Lignin content, ash content, cellulose, hot and cold water solubility of the fibres were 13.72 ± 1.21%, 1.27 ± 0.23%, 53.26 ± 1.11%, 15.20 ± 2.11 and 6.14 ± 2.43 respectively while the mechanical properties of paper from the pulp were Bursting strength (282.163 KPa m2/g), Tear strength (146.119), Tensile strength (257.6N/m) and Tensile Index (3.9Nm/g). It was found that in all properties, the corn sheath was better than the rice straw fibers but not as good as the silk cotton and bagasse fibers. However, the corn sheath has been identified, as a viable raw material for the pulp and paper industry in Nigeria.

Paper is the final product resulted from compression of fiber suspension of cellulose pulp, which is derived from wood or non-woody material. In this study, paper was made from mixture of pineapple leaves and sugarcane bagasse pulp (P:S, 100:0%, 80:20%, 60:40%, 40:60%, 20:80%, and 0:100%) at varying cooking liquor or NaOH concentration (1.5% and 3%) using semi-mechanical soda pulping method. Pulp characterisation (kappa number, tensile and tearing strength) was further carried out to ensure a stable pulp and paper quality. Results showed that the highest tensile strength of 6,709 kN was obtained at pineapple leaves and sugarcane bagasse pulp composition of 100:0% and NaOH 3%, whereas the highest tearing strength (1730,13 mN) was observed at the P:S of 40:60% with similar concentration of NaOH. The lowest kappa number (6,182) was also obtained at P:S of 0:100% and 3% NaOH. The pulp characterisation values have fullfil SNI No. 6519:2016 quality standard for plastic laminated paper.

Utilization of agro-based fibre for paper making has been the subject of interest in order to expand the usage of renewable resources as well as reduced the dependence on wood pulp. As one of the major countries in palm oil production, some of the waste from the oil palm plantation like the oil palm fronds, empty fruit bunches, and its leaf is a potential source of non-wood industry which can be used as raw material in the paper industry manufacture. This study was done to examine the potential of palm leaves to be used as a raw material of non-wood resources in the papermaking industry. In this study, sodium hydroxide (NaOH) pulping and process was employed to investigate the effectiveness of lignin removal for good fibre production. The concentration of the pulping agent was fixed at 7% at treatment of 1-7 hours to investigate the best condition for defibrillation of the cellulose fibre. Based on this study, it was found that the soda pulping produces fibre that can be molded into paper sheet without any binding agent. The morphology of the fibre observed under Scanning Electron Microscopy (SEM) shows that, soda pulping fiber consist of individual micro fibrils that are well separated. Both tensile strength and tear index gives highest value at 1.93 kg/cm2 and 37 Nm2/kg respectively at 7 hours treatment time. his reflects that lignin removal effectively occurred in soda pulping. Tensile strength found to increases with treatment time and both tensile strength and tear index of the paper falls within the value comparable to commerical non-wood paper. The paper produced has rough surface and has the potential to be develop for craft paper.

The focus of this study is to analyze whether there are differences in the difficulty index of items if the same items are displayed with the Paper Based Test (PBT) model and the Computer-Based Testing (CBT) model. The PBT and CBT models have the same paradigm of measuring estimated abilities but have differences in the context and feel aspects. These differences include the number of items in the range of eyesight, use of tools, how to work on items, basic knowledge needs about computer operations, and habit factors. These differences can affect the results of estimating the ability of test participants. This study uses development methods and quantitative methods. Development methods are used to develop package items and CBT software. Two groups of respondents were used with equal ability to work on the same question package. One group uses the PBT model, and the other group uses CBT so that the response choices are obtained in each test model. The results of the respondent’s answer choices were then analyzed by the ITEMAN software to get the item difficulty index. The item difficulty index of each model was tested statistically using SPSS software, whether there was a significant average difference between the two test models. From the results of the study and analysis in classical theory, it can be concluded that statistically there are differences in the average difficulty index of the items if the same item is displayed with the PBT and CBT models. It was found that the items displayed with the PBT model had a more difficult tendency than when displayed with the CBT model.

Thermal paper is a special type of paper that is coated with chemicals on the paper layer to change color when exposed to heat. When discovering fingerprints by using chemical reagents such as ninhydrin solution with thermal paper, it shows black staining background on the heat-sensitive front side. Thus, the latent fingerprints cannot be discovered. In this study, we have reported the first utilization of ninhydrin with water glue in different ratios for the development of latent fingerprints on the thermal papers. The results showed that at 0.020-0.060 g/mL of water glue in ninhydrin solution reduced the black strain after tested with thermal paper and made the appearance of the fingerprint more clearly. So, the detectable minutiae can be used for visualization and identification of latent prints. Using an Automated Fingerprint Identification System (AFIS), it is showed between 59-87 points of minutiae. As the results, this method could be used as an alternative method to developing latent fingerprints with non-hazardous materials, reduce costs and easy to find.

This paper is devoted to study a structure of SiC-based materials using ultrasonic tomography method. The SiC-based materials were fabricated from preceramic paper using spark plasma sintering (SPS) method. Also as part of the study the Young's modulus and density of sintered materials were determined and the effect of sintering pressure changing to this parameters value was investigated. The preceramic paper is a composite material including a matrix of organic cellulose fibers and inorganic powder filler (SiC). The sintering temperature and pressure were 2373 K and 20-40 MPa, respectively. The holding time for the sintering process was 10 min. The density of sintered materials was investigated by the hydrostatic weighing method. Ultrasonic tomography was implemented using of single-channel sensor at 10 MHz frequency. © Published under licence by IOP Publishing Ltd. Russian Science Foundation, RSF: 19-19-00192 The research was supported by the Russian Science Foundation (grant No. 19-19-00192) as well as by

The electrophysical characteristics of experimental types of electrical insulating paper modified by bacterial cellulose made of nano-gel film Komagataeibacter xylinus, disintegrated in various ways, were studied. The advantage of composites over traditional electrical insulating paper made of pine cellulose is shown in terms of electrical and mechanical strength, sorption activity and heat resistance. The efficiency of using an industrial blender to grind bacterial cellulose has been confirmed, which significantly reduces the time of its high-quality grinding.

H1 NMR relaxometry is a method that is extremely sensitive to the presence of magnetic nanoparticles, which significantly affect the transverse relaxation time of the water proton. Accordingly, the use of magnetic nanoparticles as labels allows detection of even extremely small amounts of the test substance. This paper analyzes the prospects for applying the method of solid-phase NMR-relaxometric determination of biologically active molecules. The nitrocellulose membranes are chosen as a solid phase and nanoparticles based on iron core with a carbon shell are used as magnetic labels. The possibility of detecting small concentrations of magnetic particles in porous medium is demonstrated. Finally, the ability to detect extremely low concentrations of an analyte, in this case, streptavidin protein (0.5 ng/ml to 100 ng/ml), which is actively used in various fields of biology and medicine, is demonstrated. © Published under licence by IOP Publishing Ltd. Russian Science Foundation, RSF: 17-15-01116 The work was carried out within the Russian Science Foundation project 17-15-01116. equipment of the Ural Center for Shared Use Modern nanotechnology UrFU was used.

The waste Tetra pack impose a great pressure on environment. In this paper, we use hydrothermal liquefaction technique to convert it into valuable crude oil. The paper fibre and LDPE were studied in supercritical water at 420 °C, 25 MPa and residence time of 30 min. Effect of paper fibre: LDPE on the crude oil yield, components distribution and high heat value were investigated in depth. Results showed that maximum crude oil yield of 27.33 wt% was obtained at paper fibre to LDPE of 8:2, minimum O/C of 0.094 was obtained at paper fibre to LDPE of 5:5, which reflect that HTL of paper fibre and LDPE had a synergetic effect. And the highest high heat value of the crude oil reach 37.7 MJ/kg at the ratio of 5:5• The CH radicals produced from LDPE chain can promote the hydrogenation reaction that then decrease the production of oxygen-containing groups, and also the broken of C-C bond in lignin will be accelerate, which increased the diesel (C16-C47) compound.