Search

Deep shale gas reservoirs, compared to shallow and intermediate shale gas reservoirs, usually exhibit lower fracture complexity, smaller stimulated volume, poorer conductivity, and faster production decline when the same injection scheme and construction parameters are used. As a result, specific injection scenarios for deep shale reservoirs must be investigated. In this paper, a series of laboratory fracturing tests were conducted to investigate the influence of injection scenarios on deep shale hydraulic fracture initiation and propagation. The black shale of the Lower Silurian Longmaxi formation in the Sichuan Basin was adopted, and four different injection schemes (constant fluid rate injection, cyclic injection, shut-in intermittent injection, and low-frequency pulse pressurization injection) were utilized in these experiments. The energy evolution during hydraulic fracturing with different injection schemes was analyzed by an array of acoustic emission (AE) sensors. Furthermore, the internal fracture geometry of the shale specimens after failure was determined using high-resolution CT scanning. Two parameters, fracture bulk density and fractal dimension were defined to quantitatively characterize the post-pressure fracture complexity. The results indicate that the rock breakdown pressure rises rapidly as the injection rate increases, for conventional monotonic rate injection. Although increasing the injection rate can serve the purpose of increasing the net pressure in the seam and enhancing the fracture complexity, it makes it easier to approach the equipment pressure limit. Unlike conventional hydraulic fracturing, which mainly induces tensile fractures near the wellbore, cyclic fracturing is more likely to cause fatigue damage to the rock, resulting in the formation of subcritical microcracks, which gradually grow into macroscale fractures. In addition, the cyclic injection method can reduce the rock breakdown pressure by approximately 24% compared with the conventional continuous injection method. The shut-in intermittent injection method can also reduce the breakdown pressure of shale by 22%, but this method is not conducive to enhancing the fracture complexity. Pulse fracturing creates the most complex fracture morphology among the four injection schemes tested. The rapid changes in wellbore pressure over a short time can easily result in the formation of multiple fractures around the borehole. Our experimental results and theoretical analysis can provide theoretical support for the optimization of injection schemes for deep shale hydraulic fracturing. • Laboratory tests were conducted to investigate the influence of injection scenarios on deep shale hydraulic fracturing. • All the experiments were monitored by an array of AE sensors. • The internal fractures geometry of the shale specimens after failure was determined by high-resolution CT scanning. • The cyclic fracturing can reduce the breakdown pressure by about 24% compared with the conventional continuous injection method. [ABSTRACT FROM AUTHOR]

The Longmaxi Formation has abundant shale gas resources. High-yield wells have been obtained in medium-shallow and deep areas in the Sichuan Basin. Quantitative research on the brittle-ductile change in rocks is a basic geological component for caprock evaluation, and it can also be applied to shale gas exploration. This paper fully considers the difference between the lower shale (N1) and upper shale (N2) of the Longmaxi gas-bearing shale. Through total organic carbon (TOC), mineral components, field emission scanning electron microscopy (FE-SEM), and triaxial mechanics experiments, the two groups of shale samples, N1 and N2, were compared and analyzed, and the brittle-ductile transition was quantitatively studied. Based on previous work, a method for the fast calculation of the key over consolidation ratio (OCR) was proposed. The results show that N1 is mainly organic-rich siliceous shale, N2 is primarily organic-poor clay shale and mixed shale, and N1 is generally more brittle than N2. The key OCRs of N1 and N2 are 2.16 and 2.60, respectively. The key confining pressures at which N1 and N2 become fully ductile are 87.87 MPa and 70.28 MPa, respectively. Therefore, the key depths of the brittle zones of N1 and N2 (H b1 and H b2) and the key depths of the ductile zones of N1 and N2 (H d1 and H d2) are obtained. On this basis, a comprehensive model for the Longmaxi shale gas' brittle-ductile transition exploration zone in the Sichuan Basin and H b1 and H b2 maps of the Longmaxi gas-bearing shale have been established. Through comprehensive vertical and horizontal analysis, Longmaxi shale gas exploration risks in different blocks of the Sichuan Basin have been clarified. Therefore, this study of the variation in the brittle-ductile transition has an important guiding role in refining the exploration of Longmaxi shale gas in the Sichuan Basin. • There are obvious differences between the lower shale and the upper shale. • Difference of brittle-ductile transition makes shale gas exploration more complicated. • The new method can quickly calculate the threshold value of over consolidation ratio. • The new model provides more comprehensive guidance for shale gas exploration. [ABSTRACT FROM AUTHOR]

The upper Permian Longtan Formation (LTF) shale is a new shale gas exploration and development focus in China, which was formed in a transitional depositional environment. Because of the difference in the sedimentary environment between marine-continental transitional shale and marine shale, the enrichment characteristics and mechanism of organic matter (OM) are very different. Because of a weak research foundation, the enrichment mechanism of OM in the LTF shale in the Sichuan Basin is still unclear. In this paper, shale samples of the upper Permian LTF from the Well F5 were collected, and the abundance, source and sedimentary environment of organic matter were studied by using paleoclimate, detrital input, redox, paleoproductivity and sedimentation rate parameters. The results show that the TOC content of the LTF shale is high (average = 3.04%) and reaches the high to overmature stage (average = 2.46%), indicating a favorable source rock. The LTF shale was deposited in a humid and hot climate, which was conducive to the growth and prosperity of a large number of plants. The source of organic matter was mainly terrestrial plant fragments. The sedimentary environment of the LTF shale was oxic, it had a high sedimentation rate, which reduced the oxidation rate of OM, promoted the rapid deposition of OM, and ensured the preservation of organic matter. In summary, the enrichment of OM of LTF shale in the Sichuan Basin was affected by the sedimentary environment, which was complicated. The main controlling factors were detrital input, redox conditions and sedimentation rate. • The geochemical characteristics of Permian Longtan Formation (PLTF) shale in eastern Sichuan are analyzed. • The sedimentary paleoenvironment of PLTF shale in eastern Sichuan is reconstructed. • The main controlling factors of organic matter enrichment of PLTF in eastern Sichuan are studied for the first time. [ABSTRACT FROM AUTHOR]

The lamellation fractures in marine shales are important to the accumulation and preservation of shale gas, whose characteristics and controlling factors are still unclear. This paper focus on the characteristics descriptions and controlling factor analyses based on core observations, thin sections, and scanning electron microscope (SEM) experiments. The marine shales of Paleozoic Wufeng Formation and Longmaxi Formation in the Fuling Area of Eastern Sichuan Basin are taken as an instance. The lamellation fractures are occurring along the direction of the lamellations, partially of them curved, bifurcated, and converged. The apertures of fractures typically range from 1 to 500 μm. Only a few (<1%) lamellation fractures are filled with quartz, calcite, pyrite, and bitumen. After a series of analyses, developments of lamellation fractures are controlled by total organic carbon (TOC), brittle minerals, laminae, and pyrite. (1) The organic matters control the formation and evolution of lamellation fractures by generating gas and resulting in overpressure. An increase in the TOC content of 1% can increase the lamellation fracture density by 0.26 cm-1. (2) Brittle minerals, especially authigenic quartz, is also an important controlling factor to the development of lamellation fractures. When BI increases by 10%, the lamellation fracture density increases by 19%. (3) Besides, siliceous and carbonate laminae in the shale are more suitable for lamellation fractures to develop. When the laminae density is smaller than 4 cm−1, it is easier to develop lamellation fractures with higher laminae density. However, too densely-distributed laminae will suppress the formation of lamellation fractures. (4) Higher pyrite content is good for the development of lamellation fractures. Lamellation fracture density will increase by 9%, with pyrite content increased by 1%. For the shale at the bottom of the Wufeng Formation - Longmaxi Formation, lamellation fractures develop extensively due to the high TOC and pyrite content, great brittleness, and moderate laminae density. The density of lamellation fractures decreases from the bottom to the top. • Quantitative characterize about development characteristics of the lamellation fractures. • The lamellation fractures is controlled by brittle mineral, TOC, laminae and pyrite. • TOC is the main one that affects the development of lamellation fractures. • Clarify vertical distribution characteristic of lamellation fractures in the Wufeng-longmaxi Fm. [ABSTRACT FROM AUTHOR]

The current fluid imbibition models used in shale usually assume a pore shape to be circular, whereas the pore shapes significantly deviate from that. One approach to correct this deviation is to introduce a pore shape factor into the models although it is challenging. This paper provides a way to calculate the specific shape factors of irregular inorganic and organic pores in shale based on SEM images analyses. Then, combining with the percentages of the organic and inorganic pores, a group of weighted-average pore shape factors of Longmaxi shale samples was calculated (0.587～0.667). Another group of pore shape factors (0.359～0.615) was also matched from the shale fluid imbibition curves, close to the previous values, which confirmed the validity of the proposed method. This work may provide an effective support in exploring the fluid imbibition or flow mechanisms in shale, especially considering the strong pore wall effects under nano-scale. • A method is provided to calculate the shape factors of irregular inorganic and organic pores. • The pore shape factor of organic pores is commonly higher than that of inorganic pores. • Ignoring the pore shape factor may cause an overestimation in fluid imbibition volume prediction. [ABSTRACT FROM AUTHOR]

The Lower Paleozoic Ordovician Wufeng Formation and the Silurian Longmaxi Formation shale in the southeastern part of Sichuan Basin in China are the key strata for shale gas exploration. In this paper, based on a large number of outcrops, cores and natural gamma spectroscopy logs combined with scanning electron microscopy, geochemical parameter testing and mineral component analysis, the geological conditions and exploration potential of shale gas accumulation were studied in this area, and the relationship between structure and shale gas preservation is discussed. The vertical reduction in the U/Th ratio measured in the outcrop sandstone lenses and core horizontal bedding and observed in the energy spectrum logs indicates that the sedimentary water body transformed from a low-energy anoxic reducing environment to a high-energy oxidizing environment. The TI index and the kerogen carbon isotope indicate that the organic matter type of the shale is mainly type I kerogen. The TOC content of high-quality shale is generally above 2.50%, and the R o value is between 2.00% and 3.08%. High organic matter abundance, moderate thermal evolution and a large thickness of high-quality shale ensure an adequate supply of hydrocarbon resources. Multiple types of inorganic pores, primary organic pores and pores formed during hydrocarbon generation provide abundant reservoir space for the enrichment of shale gas. The tectonics have an important influence on the preservation of shale gas. Moderate fracture development, a late tectonic uplift time, small-scale tectonic uplift, and high formation pressure coefficient are conducive to the preservation of shale gas, and the gas content and productivity will be higher. Overall, a structural stability zone with a high formation pressure coefficient is a favorable area for shale gas exploration. • Comprehensive analysis the sedimentary environment based on three scales: outcrop, core and energy spectrum logging. • Later and small-scale tectonic uplift, moderate fracture development, good roof preservation are conducive to gas enrichment. • A structural stability zone with a high formation pressure coefficient is a favorable area for shale gas exploration. [ABSTRACT FROM AUTHOR]

The initial water saturation of shale reservoirs is in general lower than the irreducible water saturation. However, the hydraulic fracture network region is highly saturated by fracturing fluid, which results in a two-phase flow inside fractured region. A long-time two-phase flow period is always observed in the fields even after a high flowback rate, which cannot be explained by existing models. In this paper, we develop a 2D gas-water flow model coupling multi-scale discrete fractures and continuum framework to describe the flowback process of a multi-stage fractured horizontal well in shale gas reservoirs. The model considers the non-linear flow mechanism of free gas, desorption of adsorbed gas and the co-existence of single gas flow and gas-water flow. The capillary pressure model and relative permeability model are both employed with different parameter values for matrix and fractures, respectively. The permeability of naturally fractured shale is described using a fractal model. To overcome non-convergence problem of finite element method for solving two-phase flow in cross fractures, the model is solved by finite element method and finite volume method. The model is verified through a simple two-phase flow simulation and a single gas phase simulation with some simplifications. Then the model is used for history matching as well as production prediction of a well in Changning block, Sichuan, China. The simulation results show that the high water saturation induced "skin factor" in the vicinity of hydraulic fractures significantly delays the gas production for a long time because some of the fracturing fluids become irreducible water and lower the gas phase permeability. Due to the great influence of fracture interference on water flow, the fracturing fluids concentrate on regions near hydraulic fractures and their junctions. The long-term gas production of the complex fracture network is slightly higher than that of the simple fracture network, which is different with the simulation results of single gas flow model. • A physical model where the gas-water coexists with single gas flow is built. • The viscous flow, Knudsen diffusion and adsorption / desorption phenomenon are considered of the gas flow in shale matrix. • The finite element method (FEM) and the finite volume method (FVM) are employed to solve the mathematical model. • The flowback and production process can be simulated continuously. [ABSTRACT FROM AUTHOR]