Search

In the process of hydraulic fracturing of shale gas horizontal wells in the Weiyuan area of Sichuan, China, casing deformation (CD) is a frequent problem that has seriously affected the benefits of shale gas development and remains to be solved for many years. In this paper, based on the analyses of Multi-finger Imaging Tool-24 (MIT-24) data, microseismic data, and the relationship between CD and engineering parameters, we confirm that the wellbore morphology in all CD sections in the Weiyuan area is consistent with shear deformation characteristics and clarify the cause of all CD: hydraulic fracturing leads to increased fluid pressure in well-intersecting faults and large fractures (F-Fs), inducing their shear slip, and eventually leads to asymmetric compression on the casing by strata on both sides of F-Fs, i.e., CD. On this basis, we propose a set of methods to control (or moderate) the shear slip of F-Fs by reducing the additional fluid pressure in target F-Fs during hydraulic fracturing to prevent CD, including multi-cluster perforations, temporary plugging F-Fs and fracturing fluid flowback. We also analyze the theoretical basis, feasibility and workflow of these methods. These methods have been tested in 44 horizontal wells in the Weiyuan area, of which the result is a radical decrease in the CD rate of the single well (from 54% to 9.1%), indicating that the slip of F-Fs and the resulting CD during hydraulic fracturing can be controlled and providing a reference for the prevention of hydraulic fracturing-induced earthquakes. • All CD during hydraulic fracturing of shale gas in the Weiyuan area is caused by induced shear slip of F-Fs. • Temporary plugging can reduce the additional fluid pressure in target F-Fs so as to prevent CD. • The integrated technical methods have been proved to be effective in preventing CD in field application. [ABSTRACT FROM AUTHOR]

Deep shale gas reservoirs, compared to shallow and intermediate shale gas reservoirs, usually exhibit lower fracture complexity, smaller stimulated volume, poorer conductivity, and faster production decline when the same injection scheme and construction parameters are used. As a result, specific injection scenarios for deep shale reservoirs must be investigated. In this paper, a series of laboratory fracturing tests were conducted to investigate the influence of injection scenarios on deep shale hydraulic fracture initiation and propagation. The black shale of the Lower Silurian Longmaxi formation in the Sichuan Basin was adopted, and four different injection schemes (constant fluid rate injection, cyclic injection, shut-in intermittent injection, and low-frequency pulse pressurization injection) were utilized in these experiments. The energy evolution during hydraulic fracturing with different injection schemes was analyzed by an array of acoustic emission (AE) sensors. Furthermore, the internal fracture geometry of the shale specimens after failure was determined using high-resolution CT scanning. Two parameters, fracture bulk density and fractal dimension were defined to quantitatively characterize the post-pressure fracture complexity. The results indicate that the rock breakdown pressure rises rapidly as the injection rate increases, for conventional monotonic rate injection. Although increasing the injection rate can serve the purpose of increasing the net pressure in the seam and enhancing the fracture complexity, it makes it easier to approach the equipment pressure limit. Unlike conventional hydraulic fracturing, which mainly induces tensile fractures near the wellbore, cyclic fracturing is more likely to cause fatigue damage to the rock, resulting in the formation of subcritical microcracks, which gradually grow into macroscale fractures. In addition, the cyclic injection method can reduce the rock breakdown pressure by approximately 24% compared with the conventional continuous injection method. The shut-in intermittent injection method can also reduce the breakdown pressure of shale by 22%, but this method is not conducive to enhancing the fracture complexity. Pulse fracturing creates the most complex fracture morphology among the four injection schemes tested. The rapid changes in wellbore pressure over a short time can easily result in the formation of multiple fractures around the borehole. Our experimental results and theoretical analysis can provide theoretical support for the optimization of injection schemes for deep shale hydraulic fracturing. • Laboratory tests were conducted to investigate the influence of injection scenarios on deep shale hydraulic fracturing. • All the experiments were monitored by an array of AE sensors. • The internal fractures geometry of the shale specimens after failure was determined by high-resolution CT scanning. • The cyclic fracturing can reduce the breakdown pressure by about 24% compared with the conventional continuous injection method. [ABSTRACT FROM AUTHOR]

The propagation characteristics and influencing factors of hydraulic fractures can be analyzed through fracturing experiments. However, there are almost no fracturing experiments in which acid fluids were considered, for the acid resistance of the equipment is always imperfect. In this paper, a physical modeling experimental equipment for acid fracturing was designed and introduced, in which corrosion protection and alternate injection were realized. The carbonate rock for acid fracturing experiment was collected from Sichuan Basin, China, which was tight with a little cavity developed. Acid fracturing experiments, in which HCL, guanidine gum and guanidine gum with an acid fluid were used as the fracturing fluids, were conducted to analyze the characteristic of acid-etched fractures. The results showed that: Acid fluid etched the fracture surface, especially in the near-wellbore area; Acid fluid would open microfractures and pores easily, and leaked into these spaces, which decreased the propagation distance of the primary acid-etched fracture; High viscosity guanidine gum was first injected and then with low viscosity acid fluid, then the latter one was transported to distal area by viscous fingering, which would lead to a better fracturing effect; Due to the acid-rock reaction, the morphology of acid-etched fracture was obviously different from hydraulic fracture, and two kinds of acid-etched fracture morphology were proposed according to the sequence of acid fluid and guanidine gum. In this paper, the characteristics of acid-etched fractures were investigated by four groups of acid fracturing experiments, which could provide a reference to optimize acid fracturing effect. • An improved acid fracturing physical modeling experimental equipment in which acid injection is allowed is developed. • Peculiar mechanical characteristics in acid fracturing are investigated and compared with hydraulic fracturing. [ABSTRACT FROM AUTHOR]

The initial water saturation of shale reservoirs is in general lower than the irreducible water saturation. However, the hydraulic fracture network region is highly saturated by fracturing fluid, which results in a two-phase flow inside fractured region. A long-time two-phase flow period is always observed in the fields even after a high flowback rate, which cannot be explained by existing models. In this paper, we develop a 2D gas-water flow model coupling multi-scale discrete fractures and continuum framework to describe the flowback process of a multi-stage fractured horizontal well in shale gas reservoirs. The model considers the non-linear flow mechanism of free gas, desorption of adsorbed gas and the co-existence of single gas flow and gas-water flow. The capillary pressure model and relative permeability model are both employed with different parameter values for matrix and fractures, respectively. The permeability of naturally fractured shale is described using a fractal model. To overcome non-convergence problem of finite element method for solving two-phase flow in cross fractures, the model is solved by finite element method and finite volume method. The model is verified through a simple two-phase flow simulation and a single gas phase simulation with some simplifications. Then the model is used for history matching as well as production prediction of a well in Changning block, Sichuan, China. The simulation results show that the high water saturation induced "skin factor" in the vicinity of hydraulic fractures significantly delays the gas production for a long time because some of the fracturing fluids become irreducible water and lower the gas phase permeability. Due to the great influence of fracture interference on water flow, the fracturing fluids concentrate on regions near hydraulic fractures and their junctions. The long-term gas production of the complex fracture network is slightly higher than that of the simple fracture network, which is different with the simulation results of single gas flow model. • A physical model where the gas-water coexists with single gas flow is built. • The viscous flow, Knudsen diffusion and adsorption / desorption phenomenon are considered of the gas flow in shale matrix. • The finite element method (FEM) and the finite volume method (FVM) are employed to solve the mathematical model. • The flowback and production process can be simulated continuously. [ABSTRACT FROM AUTHOR]