Search

Introduction: Short stem prostheses were originally designed for younger and more active patients. In recent years, they have been increasingly offered to older patients. This study evaluates the mid-to long-term survival of a short stem prosthesis and the changes in periprosthetic bone density following implantation of a cementless short hip stem in patients over 60 years of age., Methods: 118 patients aged over 60 received short stem prostheses. Clinical examination included Harris Hip Score (HHS) and Hip Disability and Osteoarthritis Outcome Score (HOOS). 93 patients were followed clinically for at least five years. 53 patients underwent dual-energy x-ray absorptiometry (DXA) and radiographic evaluation. Follow-up intervals were preoperative and postoperative (t 0 ), at approximately six months (t 1 ), at approximately two years (t 2 ), and at approximately five years or later (t 3 )., Results: Over a mean 6.7-year observation period for all 118 patients, one stem revision occurred due to a traumatic periprosthetic stem fracture. The five-year survival rate for the endpoint survival of the Metha® stem in 95 at-risk patients is 99.2%. HHS improved significantly from t 0 55.3 ± 11.5 (range 30-79) to t 3 95.3 ± 8.6 (range 57-100) at a mean of 8.0 years (p < 0.001). HOOS improved significantly in each subscale (p < 0.001). Bone mineral density (BMD) was available for review in 53 patients after a mean of 7.1 years. BMD increased from t 0 to t 3 in region of interest (ROI) 3 (+0.4%) and ROI 6 (+2.9%) and decreased in ROI 1 (-10.3%), ROI 2 (-9.8%), ROI 4 (-5.3%), ROI 5 (-3.4%) and ROI 7 (-23.1%)., Conclusions: The evaluated short stem prosthesis shows a remarkably high survival rate in elderly patients, accompanied by excellent clinical results. Load transfer measurements show a metaphyseal-diaphyseal pattern with a trend towards increased diaphyseal transfer over the period observed., Competing Interests: None., (© 2024 The Authors.)

Introduction: In order to improve the anchorage behavior of short hip stems, this development project aims at designing a short hip stem concept that preserves the femoral neck and minimizes interference with the physiological stress distribution of the femur. The new design will be evaluated according to ISO 7206-4 which is the standard for testing Implants for surgery., Methods: Basic CAD models based on an established short stem prosthesis were created and evaluated using finite element analysis. The best design was further developed to achieve a more deformable stem while maintaining stability. The model was validated through in vitro testing., Results: The "H-Beam" short stem showed a higher degree of deformation of approximately 142-144% compared to the established short stem. The FE model had a relative error of 0.98% and 1.07% compared to the in vitro tests. An operating procedure was outlined for this new short stem design., Discussion: The FE model is deemed valid due to small differences in comparison to in vitro testing. The short-stem prosthesis is more flexible and can be easily adapted to individual anatomy during surgery. The prosthesis length is similar to conventional prostheses, but the new stem design could allow better and faster osteointegration while preserving the cancellous bone structure., Competing Interests: The authors declare that there are no conflicts of interest., (© 2023 Professor P K Surendran Memorial Education Foundation. Published by Elsevier B.V. All rights reserved.)

Background: Currently, the influence of muscle traction on the postoperative stability of humeral prostheses is not adequately researched. This study analyzed the prosthesis' stability in vitro during muscle traction considering different bone defect sizes., Methods: The reverse humeral prosthesis "AEQUALIS™ ADJUSTABLE REVERSED" (Stryker) was implanted using press-fit into ten bones with a length of 200 mm and 160 mm. Subsequently, the models were torqued in 30 cycles using a universal testing machine (2 Nm - 6 Nm) and loaded axially to simulate muscle traction. The axial weight increased from 7.7 kg (pure muscle traction) over 40 kg (45-degree abduction) to 69.3 kg (90-degree abduction). The prosthesis' relative micromotion was simultaneously measured at three different measurement heights using high-sensitivity displacement transducers and compared to the relative micromotion without axial load., Results: It was found that a larger torsional moment was associated with a larger relative micromotion in both bone defects studied. However, the influence became significant ( P  < 0.014) in bone models with predominantly larger defect.Furthermore, no significant influence of muscle traction on relative micromotion could be detected for the larger bone models at any of the measurement levels ( P  = 1.000). In contrast, smaller bones showed no significant differences in muscle traction until a torsional moment of 6 Nm ( P  < 0.028)., Conclusion: In conclusion, a larger torsional moment is associated with a higher relative micromotion and muscle traction, conclusively, has no effect on the primary stability of the reverse prosthesis for a 200 mm bone in vitro ., (© 2023 Professor P K Surendran Memorial Education Foundation. Published by Elsevier B.V. All rights reserved.)

Introduction: The worldwide rising number of joint replacements results in increasing revision surgery including a relevant portion of septic loosening accompanied by bone deficiencies. Loading of allogeneic bone with antibiotics provides high local antibiotic concentrations and might eradicate bacteria which appear resistant to systemic antibiotic application. Hydrophobic palmitic acid was shown to be a suitable carrier for antibiotics and prevents biofilm., Methods: Cancellous bone derived from 6 to 7 months old piglets was used for a standardized in vitro impaction bone grafting model according to previous studies. The specimens were either thermodisinfected or remained native and palmitic acid with one third and two third partial weight were added and compared with control. Shear force at the interface prosthesis to cement and between cement and bone was measured. The relative micromovements were measured with 6 inductive sensors with a resolution of 0.1 μm at three different measuring heights up to a maximum movement of 150 μm between cement and bone. Taking into account the corresponding applied torque the measured values were normalized in μm/Nm. Statistical analysis was done with SPSS Statistics® Version 26.0 IBM., Results: Smallest movement was measured for thermodisinfected cancellous bone and a not significant decrease of shear force resistance with addition of palmitic acid was found since supplementing native cancellous bone reduced shear force resistance significantly depending on the weight percentage of palmitic acid., Conclusion: Supplementation of porcine cancellous bone with palmitic acid did not significantly reduce shear force resistance of thermodisinfected bone since adding palmitic acid to native bone decreased it significantly depending on the volume added. Palmitic acid seems to be a suitable coating for allogeneic cancellous bone to deliver high local antibiotic concentrations and thermodisinfected cancellous bone might be able to store larger volumes of palmitic acid than native bone without relevant influence on shear force resistance., Competing Interests: None., (© 2022 Published by Elsevier B.V. on behalf of Professor P K Surendran Memorial Education Foundation.)

Background: Evaluation of the mechanical behavior of the microstructure of cancellous bone seems important for the understanding of the mechanical behavior of bone. Prevention and treatment of fragility fractures due to osteoporosis is a major challenge according to ageing population. A bone model might help to assess fracture risk. Measurement of single trabeculae of bone should give further information compared with bone densitometry alone. This study measures the mechanical properties of single cancellous trabeculae derived from human proximal humerus., Methods: 34 single trabeculae dissected from human humeral heads were measured and evaluated mechanically. Trabeculae were fixed on microscope slides and geometrical data were reported during axial rotation of the specimens to measure the transverse section using computer aided design (CAD). The samples were subjected to a two-point bending test and were loaded with a measure-stamp at a defined distance. Force and deflection were measured by high-resolution sensors. The E-modulus was then calculated in combination with finite elements method simulation (FEM), using the previously obtained CAD-Data., Results: The average E-modulus from 34 valid measurements of human humeral trabeculae was 1678 MPa with a range from 829 to 3396 MPa, which is consistent with existing literature. The planned additional validation of the measurement method using manufactured three-dimensional synthetic trabeculae with known mechanical properties showed an average elastic modulus of single trabeculae of 51.5 MPa, being two dimensions lower than the value reported in the datasheet of the plastic., Conclusion: This newly developed, time and cost-efficient procedure allows the measurement of E-modulus in single trabeculae. Measurement of mechanic parameters of single trabeculae might give insights on mechanic behavior of bone and be relevant for the research of systemic bone diseases, complementing the existing data on bone-mineral-density. Further examination of single trabeculae of human cancellous bone should give an insight on the mechanical behavior of bone also considering systemic bone diseases., Competing Interests: None., (© 2022 Professor P K Surendran Memorial Education Foundation. Published by Elsevier B.V. All rights reserved.)

Introduction: Good osteointegration of implants requires sufficient primary stability. Aim of this study was to examine the influence of screw fixation on the primary stability of press-fit cups., Methods: Two press-fit acetabular cups were tested with regard to the influence and number of screws and their primary stability., Results: For the relatively thin-walled Allofit®-S cup, an influence of the number of screws on the different forms of movement could be demonstrated., Conclusions: We see a clear influence of the cup wall thickness on the elastic deformability and accordingly on the primary stability of the examined cups., Competing Interests: The authors declare that they have no conflict of interest., (© 2020 Professor P K Surendran Memorial Education Foundation. Published by Elsevier B.V. All rights reserved.)