Search

This paper presents the experimental investigation of the effect of Nb2O5 content on the phase composition, microstructure, and physical and mechanical performance of the zirconia-toughened alumina (ZTA) ceramics, aimed to optimize the additional amount of Nb2O5, refine the ceramic grains, and improve the densification, hardness and fracture toughness. ZTA ceramics with various Nb2O5 contents were prepared using the spark plasma sintering method. The addition of trace amounts of Nb2O5 did not produce a new Nb-rich phase; the Nb atoms were dissolved in the ZrO2 grains. The addition of trace amounts of Nb2O5 led to grain refinement and an increase in density, but the addition of excessive Nb2O5 resulted in grain growth and a decrease in relative density. Furthermore, the addition of Nb2O5 promoted uniformity of the microstructure. The sample with 0.25 wt.% Nb2O5 had the maximum Vickers hardness and indentation fracture toughness, which were 1228.40 HV and 9.17 MPa √m, respectively. Mechanical properties of the composite mainly depended on the grain size, which was influenced to some extent by the relative density. [ABSTRACT FROM AUTHOR]

The paper reviews the wear behaviour of oxide ceramics. Wear maps are considered and consequently mild and severe wear are defined. Since the use of ceramics in engineering applications require operation in the mild wear regime, the paper concentrates on mild wear mechanisms, but also considers factors which control the transition to severe wear. Within the mild wear regime, the formation of tribofilms are discussed and the manner in which dislocation activity leads to the wear transition is considered. The wear of so-called ceramic nanocomposites, for which no time dependent wear transition has yet been observed, is considered and the reasons for enhanced performance discussed. The role of transformation toughening in zirconia ceramics is considered in detail, and reasons for the generally poor wear response of these materials defined. [ABSTRACT FROM AUTHOR]

Designing tissue engineering scaffolds with the required mechanical properties and favourable microstructure to promote cell attachment, growth and new tissue formation is one of the key challenges facing the tissue engineering field. An important class of scaffolds for bone tissue engineering is based on bioceramics and bioactive glasses, including: hydroxyapatite, bioactive glass (e.g. Bioglass®), alumina, TiO2 and calcium phosphates. The primary disadvantage of these materials is their low resistance to fracture under loads and their high brittleness. These drawbacks are exacerbated by the fact that optimal scaffolds must be highly porous (>90% porosity). Several approaches are being explored to enhance the structural integrity, fracture strength and toughness of bioceramic scaffolds. This paper reviews recent proposed approaches based on developing bioactive composites by introducing polymer coatings or by forming interpenetrating polymer-bioceramic microstructures which mimic the composite structure of bone. Several systems are analysed and scaffold fabrication processes, microstructure development and mechanical properties are discussed. The analysis of the literature suggests that the scaffolds reviewed here might represent the optimal solution and be the scaffolds of choice for bone regeneration strategies. [ABSTRACT FROM AUTHOR]

A study of the structural characteristics of the composites [Pb(Fe0.5Nb0.5)O3(PFN)] x -[Cr0.75Fe1.25O3(CRFO)]100− x ( x = 0 (CRFO100), 10, 50, 90, 100) was performed in this work. The compounds PFN100 and CRFO100 were prepared by conventional solid-state method and investigated by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and 57Fe Mössbauer Spectroscopy techniques. The X-ray analysis shows that PFN100 is tetragonal and the CRFO100 phase has a trigonal symmetry. The refinement of all the composites was also performed and discussed in this paper. The Mössbauer spectrum for the composite samples shows a paramagnetic doublet and a sextet probably assigned to a magnetic phase associated to Fe+3. For the sample PFN100, only a magnetic field of 49.5 T (isomer shift (δ) = 0.21 mm/s) was detected. For the composite sample, the δ and Δ are typical of Fe ions at sites of octahedral coordination. [ABSTRACT FROM AUTHOR]

Gd3+ was chosen as a substitute for Bi3+ in BiNbO4 ceramics, and the substitution effects on the sintering performance and microwave dielectric properties were studied in this paper. The high temperature triclinic phase was observed only in the Bi0.98Gd0.02NbO4 ceramics when sintered at 920 °C. Both bulk densities and dielectric constant (εr) increased with the sintering temperature, while decreased with the Gd content. The quality factor ( Q) exhibited a correlation to the Gd content and the microstructures of Bi1− x Gd x NbO4 ceramics. At the sintering temperature of 900 °C, Bi0.992Gd0.008NbO4 ceramics exhibited microwave dielectric properties of εr ∼ 43.87, Q × f ∼ 16,852 GHz (at 4.3 GHz), and its temperature coefficient of resonant frequency (τf) was found to be near-to-zero. [ABSTRACT FROM AUTHOR]

This paper deals with the effects of preparation methods on the texture development and densification in textured SrBi4Ti4O15 (SBT) ceramics. The specimens were prepared by the oriented consolidation of anisotropic particles (OCAP), templated grain growth (TGG) and reactive templated grain growth (RTGG) methods. The specimens with extensive texture were obtained by all methods except for TGG with small template and large matrix particles. The origin of extensive texture development was the growth of aligned platelike particles. A characteristic of microstructure was the formation of colonies, in which platelike grains contacted face-to-face. The size of colonies was dependent on the preparation method, and determined the size of pores between colonies, which had a large effect on the sintered density. The OCAP and RTGG methods gave the green compacts composed of only platelike particles and large colonies and pores formed during sintering. The TGG method gave the green compacts composed of platelike and equiaxed particles and prevented the formation of large colonies and pores during sintering. Thus, the dense, highly-textured SBT ceramics were obtained by the TGG method. [ABSTRACT FROM AUTHOR]