Search

The Journal of Materials Science awards the annual Robert W. Cahn Prize to recognize the best paper published in the journal each year. The winner of the 2023 Cahn Prize is a research paper titled "Molecular modelling of graphene nanoribbons on the effect of porosity and oxidation on the mechanical and thermal properties." The paper presents molecular simulation models of graphene nanoribbons and examines the impact of porosity and oxidation on their mechanical and thermal conductivity properties. The paper is well-written and provides valuable insights for researchers in this field. Two other papers were selected as runners-up for the prize. All the monthly finalists for the Cahn Prize can be downloaded for free on the journal's website. [Extracted from the article]

In this paper, the effects of biaxial mean stress, mainly contributed by the weld residual stress, and thermal loading conditions on cracking directions and damage in high cycle thermal fatigue crazing subjected to variable amplitude loadings are investigated by a combined analytical and computational approach. The cracking directions are related to the orientation of the critical plane defined by the maximum damage. Analytical solutions of the critical plane orientation under constant amplitude biaxial tension/compression loadings are first derived and then employed to study the effects of biaxial mean stress on the critical plane orientation. The critical plane orientation appears to strongly depend on the dominant direction defined by the larger maximum stress. The developed analytical solution of the critical plane orientation and the analytical solution of the thermal stress from the literature are employed to study the effects of thermal loading conditions on the critical plane orientation. The critical plane orientation does not seem to significantly depend on the frequency, the amplitude and the mean value of the fluid temperature fluctuations, and the heat transfer film coefficient between the fluid and the pipe wall. The critical plane orientation under variable amplitude loadings is also studied, and an approximate solution is proposed for convenient engineering applications. The critical plane orientations are used to partially explain the observed cracking directions in the high cycle thermal fatigue crazing in the old residual heat removal system of a nuclear power plant. Finally, the effects of biaxial mean stress and thermal loading conditions on the fatigue crack initiation life are discussed. [ABSTRACT FROM AUTHOR]

In this paper, the plastic deformation behavior and strain homogeneity of the ZK60 Mg alloy during the multi-pass cyclic extrusion and compression (CEC) was simulated using the finite-element method (FEM) with a view to provide an insight into the mechanics of the process. Physical modeling (PM) experiment with same alloy was carried out to verify the results of the numerical simulations. The results show that two vortex flow regions with opposite flow direction are formed inside the cylindrical workpiece during CEC deformation. Although the deformation is inhomogeneous in both end regions of workpiece, a uniform region of equivalent strain exists, and the extent of uniform deformation increased with the increase in workpiece length. [ABSTRACT FROM AUTHOR]

This paper has clarified the anelasticity of 8Y-FSZ/α-alumina composites wherein the 8Y-FSZ phases are dispersed like islands. The amount of anelastic strain generated and the manner of anelastic deformation were compared to those of monolithic 8Y-FSZ. The anelastic strains of six kinds of 8Y-FSZ/α-alumina, as well as of monolithic 8Y-FSZ and monolithic α-alumina, were measured. The results showed that the anelastic strain was produced even in the composite where 8Y-FSZ phases existed as islands, and that the more the anelastic strain produced, the higher the volume fraction of 8Y-FSZ. In addition, the composition with a fully densified alumina phase had the effect of inhibiting anelastic strain in the 8Y-FSZ phase. [ABSTRACT FROM AUTHOR]

Some basic aspects of electromagnetic radiation (EMR) emission during quasi-static plastic deformation and crack propagation in ASTM B 265 grade 2 titanium sheets are reported in this paper. It has been observed that titanium emits several intermittent EMR signals starting near the yield and continuing up to fracture. The EMR emissions are sensitive to the applied strain rates. The number of EMR emissions shows a parabolic variation with strain rate, exhibiting a maxima. It appears that the temporary pinnings of the dislocations injected from the crack tip, which is essential for the emission of EMR as described in a recent model by the authors, do not adequately occur at high as well as low strain rates. At elevated temperatures, the square of the EMR amplitude is observed to be proportional to $$ \exp {\left( { - {mU} \mathord{\left/ {\vphantom {{mU} {kT}}} \right. \kern-\nulldelimiterspace} {kT}} \right)}, $$ where U is the activation energy for the movement of jogs, k the Boltzmann constant, T the temperature and m ≤ 1.0. [ABSTRACT FROM AUTHOR]

A general approach to simulate the mechanical behaviour of entangled materials submitted to large deformations is described in this paper. The main part of this approach is the automatic creation of contact elements, with appropriate constitutive laws, to take into account the interactions between fibres. The construction of these elements at each increment, is based on the determination of intermediate geometries in each region where two parts of beams are sufficiently close to be likely to enter into contact. Numerical tests simulating a 90% compression of nine randomly generated samples of entangled materials are given. They allow the identification of power laws to represent the evolutions of the compressive load and of the number of contacts. [ABSTRACT FROM AUTHOR]

In recent years, important efforts have been focused on rapid production of tools using Rapid Prototyping and Manufacturing (RP&M) technologies such as the Stereo-Lithography Apparatus (SLA). One of the applications is the development of rapid polymer tooling such as dies for injection molding. For these applications, optimal thermal as well as mechanical properties of final tools are of significance. In order to characterize the mechanical response of materials made by SLA, a standard set of material tests, including uniaxial tension and compression tests under different strain rates and different temperatures, was conducted for both silica filled and non-filled resin. In this paper, the mechanical response of the non-filled SL5170 cured resin is discussed in terms of an elastic-viscoplastic material model. Further, a new model for silica filled SL5170 cured resin was developed to estimate the stress-strain relationship of the composite. This composite model is an extension of the elastic-viscoplastic model for non-filled resin to include the elastic deformation of the silica particles. The stress-strain curves predicted by the models under homogeneous deformation show good agreement with the experimental results. [ABSTRACT FROM AUTHOR]