Search

Haynes 282 is a γ ′ precipitation-strengthened nickel-based superalloy known for its exceptional high-temperature creep resistance and excellent fabricability. Recent advancements in powder-bed fusion-based additive manufacturing (PBF-AM) have enabled the fabrication of Haynes 282 with accurate, site-specific control of the grain orientation and morphology at the microscale. This ability opens up new avenues for microstructure design, to improve the material's fatigue crack resistance and service life. This paper investigates the fatigue crack growth behavior of hybrid microstructure Haynes 282 fabricated via PBF-AM. Previous experiments revealed a higher crack propagation rate in the coarse columnar-grained microstructural regions when compared against fine-grained areas. Here, a strain gradient crystal plasticity model was adapted to study the fracture-related mechanical fields at the crack tip in the two microstructures. The simulation results showed a consistent influence of grain structure and texture on crack propagation, as was seen in the experiment. The model analysis revealed higher crack propagation driving force along crack direction in the coarse-grained sharply textured microstructure and higher driving force for crack kinking in fine-grained more diffusely textured microstructure, which is ascribed to the combined effect of yield stress, hardening rate, texture and grain morphology. The presented modeling approach will facilitate the development of the AM-based accurate microstructure design by deepening the fundamental study in AM-specific microstructure-properties relations. [ABSTRACT FROM AUTHOR]

The tension-tension fatigue behavior and damage mechanism of basalt fiber-reinforced epoxy polymer (BFRP) composites at different stress ratios are studied in this paper. The fatigue experiments were performed under stress ratios, R = σmin/σmax of 0.1 and 0.5, while the lifetime and the stiffness degradation were monitored and analyzed to investigate the effect of stress ratios. The damage propagation during fatigue loading was periodically monitored by using an in situ scanning electron microscope (SEM). The results show that the fatigue life decreases and the fatigue life degradation rate increases with the decrease of stress ratio for examined BFRP composites. The stiffness degradation is also sensitive to different stress ratios, showing a greater stiffness loss before failure at lower stress ratio. From the SEM images, it is indicated that the micro-damage mode shifts from interface debonding and matrix cracking into fiber breaking with decreasing stress ratios. [ABSTRACT FROM AUTHOR]

This paper investigates the fatigue properties and deformation behavior of the T6-treated Mg-2.99Nd-0.18Zn-0.38Zr (NZ30K) and an AZ91D-T6 magnesium alloys with the same grain size. Compared with the AZ91-T6 alloy, the NZ30K-T6 alloy shows significant increases in mechanical properties, achieving 17 MPa in YS, 51 MPa in UTS, 2.4 % in elongation, and 15 MPa in FS, respectively. The NZ30K-T6 alloy also shows higher cyclic stress amplitudes in comparison with the AZ91-T6 alloy. This is attributed to increased matrix strength from the higher precipitate strengthening in the NZ30K-T6 alloy. The cyclic stress amplitude of the AZ91-T6 alloy increases with increasing the number of cycles. For the NZ30K-T6 alloy, the cyclic stress amplitude first increases and then decreases during cyclic deformation. Hysteresis loops were symmetrical at all total strain amplitudes due to the lessened extents of texture in these cast magnesium alloys and the absence of twinning-detwinning during cyclic deformation. For both AZ91-T6 and NZ30K-T6 alloys, the cracked slip bands initiate the fatigue cracks and also assist the crack propagation. The Coffin-Manson law and Basquin equation can be used to evaluate the fatigue parameters and predict the LCF lives of both AZ91-T6 and NZ30K-T6 alloys. The multi-scale fatigue (MSF) life models and the same model parameters were also used to predict the HCF lives of these alloys. [ABSTRACT FROM AUTHOR]

This paper aims to statistically estimate the dynamic fatigue strength in brittle materials under a wide range of stress rates. First, two probabilistic models were derived on the basis of the slow crack growth (SCG) concept in conjunction with two-parameter Weibull distribution. The first model, Model I, is a conventional probabilistic delayed-fracture model based on a concept wherein the length of the critical crack growth due to SCG is enough larger than the initial crack length. For the second model, Model II, a new probabilistic model is derived on the basis of a concept wherein the critical cracks have widely ranging lengths. Next, a four-point bending test using a wide range of stress rates was performed for soda glass and alumina ceramics. We constructed fracture probability-strength-time diagrams (F-S-T diagrams) with the experimental results of both materials using both models. The F-S-T diagrams described using Model II were in good agreement with plots of the fracture strength and the fracture time of both materials more so than Model I. [ABSTRACT FROM AUTHOR]

The paper focuses on modeling the strain fatigue lives of three commonly used cable insulation polymers, namely (1) polyvinyl chloride, (2) crosslinked polyethylene, and (3) polyphenylene ether under selected strain and temperature ranges. On the basis of results obtained from their fatigue tests, Coffin–Manson model, mean/maximum strain fatigue model, and a set of new semi-empirical equations were applied to establish the relationship between fatigue lives and strains. The unified strain model, herein we name it the Wei–Wong model, is developed to predict the fatigue lives of three polymers studied and their prediction capability was examined using our experimental data. It was found that the proposed Wei–Wong model can provide a better life prediction compared to the experimental data and other methods in the literature at selected temperatures, namely −40, 25, and 65 °C. [ABSTRACT FROM AUTHOR]

In this paper, yield and fatigue behavior of a polypropylene nanocomposite and a polyamide-6 nanocomposite has been studied. The Eyring equation was used to model the temperature and strain rate sensitivity of the yield strengths of these two nanocomposites. Both activation volume and activation energy of the polypropylene nanocomposite were higher than those of the polyamide-6 nanocomposite. The fatigue strength of the polyamide-6 nanocomposite was higher than that of the polypropylene nanocomposite. However, the ratio of maximum fatigue stress to yield strength of the polypropylene nanocomposite was higher than that of the polyamide nanocomposite. The fatigue failure in both composites was initiated at agglomerated nanoparticles. [ABSTRACT FROM AUTHOR]