Search

The May 2024 issue of the Journal of Materials Science features a cover paper titled "Role of stacking fault energy in confined layer slip in nanolaminated Cu" by Ji et al. The paper explores the deformation of metallic nanolaminates and acknowledges the contribution of Professor Hussein Zbib. The issue is dedicated to honoring Professor Zbib's memory and was conceived by Guest Editors Tariq Khraishi, Georges Ayoub, Sinisa Mesarovic, and Mutasem Shehadeh. The paper includes references to previous work but does not mention any measurements of the intrinsic stacking fault energy. The corresponding author is Professor Shuozhi Xu from the University of Oklahoma, and the last author is Professor I.J. Beyerlein, who has a background in research and was born in Los Alamos. The paper is freely accessible through the SharedIt link provided. [Extracted from the article]

The regulation of hydrogen content in the continuous casting process is conducive to the reduction of pore defects in the casting billet. In this paper, the influence of negative pressure (NP) and continuous casting speed (CCS) on hydrogen content in copper rod billet prepared by negative pressure continuous casting (NPCC) technique was analyzed, and the mechanism of the coordinated coupling of NP and melt flow on hydrogen removal was revealed. It is clarified that with the CCS of 20 mm min−1 and an increase in the NP value from − 20 to − 80 kPa, the hydrogen content is reduced from 1.0 to 0.3 ppm. The coordinated action of NP and melt flow induced by CCS can minimize the hydrogen content. When the NP value is − 80 kPa and the CCS is 10 mm min−1, the hydrogen content is as low as 0.2 ppm, and the hydrogen removal rate is 85.7%. The larger the NP, the smaller the critical nucleation radius of the hydrogen bubble, and the larger the growth rate of the hydrogen bubble. The coupling of the NP field and flow field can make the melt which is difficult to nucleate and grow of the hydrogen bubble flow to the position which is easy to nucleate and grow. The effect of the vortex fields in the purification chamber on the removal of hydrogen is not affected by the CCS, but the CCS affects the floating of hydrogen at the solidification front, which leads to a small increase in the hydrogen content with the increase of the CCS. Our study provides a theoretical basis for the preparation of high-quality metal billets. [ABSTRACT FROM AUTHOR]

In this paper, high-density (60−x)Fe−Cr−Co−xCu (x: 0–6 wt.%) permanent magnet alloys were fabricated by laser powder bed fusion (LPBF) in-situ alloying technique, and the effects of Cu content on the microstructure, magnetic, and mechanical properties of the alloy were systematically investigated. The addition of 2 wt.% Cu enhanced the coercivity H c and the energy product (B H) max of the alloy in the isotropic state by 19.4 and 27.9%, respectively, compared to the alloy without Cu. The impacts of Cu content on the magnetic properties were investigated by combining experimental results and first-principles calculations. Furthermore, the addition of Cu improved the yield strength of the alloy, and the strengthening mechanism was analyzed in detail. The yield strength of the alloy with 2 wt.% Cu reached 908 MPa, representing a notable 7% increase relative to the Cu-free alloy. [ABSTRACT FROM AUTHOR]

With the continuous downsizing of solder joints, the influence of the grain characteristics of the under bump metallization (UBMs) on the interfacial reaction is exposed. In this paper, the effect of grain characteristics of Cu UBM on the growth of interfacial intermetallic compounds and the formation of Kirkendall voids in Cu/Sn/Cu micro solder joints during isothermal aging at 150 °C was investigated. Electroplated polycrystalline Cu (EP-Cu), (111) single crystal Cu ((111) Cu), and (111) nano-twinned Cu ((111) nt-Cu) were selected as UBMs. After reflow soldering, the Cu6Sn5 grains formed on (111) nt-Cu were near to the orientation (2 1 - 1 - 3) , while those were randomly formed on both EP-Cu and (111) Cu. During isothermal aging, the Cu6Sn5 grains exhibited the highest growth rate on (111) nt-Cu UBM, and the slowest growth rate on (111) Cu UBM, due to the differing number of diffusion routes among the three Cu UBMs with distinct grain characteristics. Furthermore, no Kirkendall voids were detected on the (111) Cu UBM, however, a significant number of Kirkendall voids were identified on the (111) nt-Cu UBM, which can be attributed to the diffusion path and impurities present in the three Cu UBMs. The results will offer theoretical and practical recommendations for the selection of Cu UBMs for micro solder joints in 3D packaging interconnection technology. [ABSTRACT FROM AUTHOR]

Solar-driven interfacial evaporation is a sustainable and green desalination method with great prospects for development in today's severe water shortage problem. In this paper, a novel composite aerogel was prepared by hydrothermal method with sodium alginate (SA) and Cu2+ in the preparation process using reduced graphene oxide as photothermal material and cellulose nanofibers as substrate. The good hydrophilicity of nanocellulose makes the composite aerogel have strong capillary action and continuous water transport. The gel formed by ion exchange between SA and Cu2+ greatly improves dry and wet mechanical strength of the composite aerogel and ensures the stability of the evaporator for multiple recycling. Copper is doped by reduction of copper ion complexes and reduced graphene oxide have a synergistic effect to increase the photothermal response rate of the composite aerogel of 1.446 kg m−2 h−1 with evaporation efficiency of 84.87% under one standard solar irradiation. In addition, the purification of heavy metal ions, dye wastewater as well as acid and alkali solutions also has excellent results. It is expected that this study will provide some new ideas for the fields of seawater desalination and wastewater treatment. [ABSTRACT FROM AUTHOR]

The demolding process of electroforming technology in fabricating microstructured optical-functional thin films produces the problem of excessive bonding between the metal substrate and the metal replica, which triggers the deformation of the microstructure and the reduction of precision, and the deposition of Cr–O–C discrete nuclei at the interface can play a good role in assisting the demolding effect. In this paper, the tensile deformation of polycrystalline Cu/Ni and Cu/Cr–O–C/Ni composites is investigated using molecular dynamics methods. The results show that the Cu/Ni model produces a large number of HCP structures during stretching, with holes at the interface and a large number of Cu atoms transferring to the Ni layer. The addition of the Cr–O–C layer reduces the yield strength of the Cu/Cr–O–C/Ni model by 26.41%, and at the same time, the dislocation proliferation at the interface is reduced, and the fracture is at the centralized interface, and the fracture time is reduced by 90.8%. The higher number of Cr–O–C atoms at the interface decreases the transfer of Cu atoms to the Ni layer. The results provide a possible explanation for the Cr–O–C layer-assisted precision electrodeposition debonding. [ABSTRACT FROM AUTHOR]

A novel microstructured catalyst that consists of Cu/ZnO catalyst powders and ceramic fibers was successfully prepared using pulp fibers as a tentative matrix by a papermaking technique. As-prepared material, called a paper-structured catalyst, possessed porous microstructure with layered ceramic fiber networks (average pore size ca. 20 μm, porosity ca. 50%). In the process of methanol autothermal reforming (ATR) to produce hydrogen, paper-structured catalysts demonstrated both high methanol conversion and low concentration of undesirable carbon monoxide as compared with catalyst powders and pellets. The catalytic performance of paper-structured catalysts depended on the use of pulp fibers, which were added in the paper-forming process and finally removed by thermal treatment before ATR performance tests. Confocal laser scanning microscopy and mercury intrusion analysis suggested that the tentative pulp fiber matrix played a significant role in regulating the fiber-network microstructure inside paper composites. Various metallic filters with different average pore sizes, used as supports for Cu/ZnO catalysts, were subjected to ATR performance tests for elucidating the pore effects. The tests indicated that the pore sizes of catalyst support had critical effects on the catalytic efficiency: the maximum hydrogen production was achieved by metallic filters with an average pore size of 20 μm. These results suggested that the paper-specific microstructures contributed to form a suitable catalytic reaction environment, possibly by promoting efficient diffusion of heat and reactants. The paper-structured catalyst with a regular pore microstructure is expected to be a promising catalytic material to provide both practical utility and high efficiency in the catalytic gas-reforming process. [ABSTRACT FROM AUTHOR]

The dielectric loss of Cu with high thermal conductivity is large at high frequency, which cannot meet the performance requirements in high-integrated circuits. There is an urgent need for materials to reduce its dielectric loss. In this paper, the thermal conductivity and dielectric properties of the AlN coating-Cu substrate system were controlled by changing the N2 pressure. The results showed that the crystallinity of hcp-AlN in AlN coating increased significantly when the proportion of N2 pressure was increased. With the increase of the N2 pressure, the particle size on the surface and the roughness of the coating improved. The AlN coating prepared at high N2 pressure had high dielectric constant and low dielectric loss at high frequency compared to those of the coatings prepared at low N2 pressure. At the same time, the AlN coating prepared under high N2 pressure on the Cu substrate did not decrease the thermal conductivity of Cu substrate. The AlN-Cu system prepared in this paper had high thermal conductivity and good dielectric properties, providing theoretical guidance for integrated circuit packaging and capacitor applications. [ABSTRACT FROM AUTHOR]

Understanding the mechanisms behind sintering Cu-Ag core–shell nanoparticles can help us optimize the sintering process parameters and design the core–shell structure to achieve the desired sintering structure. In this paper, we employed molecular dynamics simulations to investigate the sintering behaviors and mechanisms of CS NPs, taking into account the effects of shell thickness, particle size, and temperature. Our results revealed that dislocation loops in Cu-Ag CS NPs played a crucial role in sintering by emitting dislocations that facilitated crystal evolution, thereby reducing the number of amorphous structures. The state of dislocation loops could be controlled by shell thickness and NP size. As the shell thickness decreased to 0.5 nm, the structure of the dislocation loops could not be generated due to the extremely chaotic and thin Ag atoms. Furthermore, for NPs of the same size, the CS NP with a 0.5-nm shell thickness was the most active. Despite the neck not consisting of a Cu core, the Cu core, particularly its interface, could still participate in the sintering process. At 900 K, limited interface diffusion could be activated. [ABSTRACT FROM AUTHOR]

The impact of solute Al on the penetration of Cu atoms into the Fe grain boundary (GB) in the Fe–Cu embrittlement system was investigated by performing molecular dynamics simulations. Furthermore, the first principle density functional theory calculation was also employed to determine the binding properties and the electronic structure of GBs doped with solute atoms. The inhibition mechanism of liquid metal embrittlement (LME) cracks in the Fe–Cu system by Al was analyzed at the atomic scale by conducting simulations and calculations. The results show that the diffusion rate of Al along with the GB direction was much higher than that of Cu, and the preferential penetration and segregation of Al atoms acted as a barrier layer. Moreover, the addition of Al reduced the potential energy of Cu atoms, thus stabilizing their motion. These factors significantly inhibited the diffusion of Cu atoms along with the GB direction. The binding property of Fe GB doped with a high concentration of Cu was severely deteriorated, while the Al doping improved the atomic bonding. GBs with higher binding properties are less susceptible to fracture and groove under the application of tensile stress. This paper presents a novel perspective on the inhibition mechanism of LME cracks by doping a third component to inhibit the penetration of embrittlement atoms. [ABSTRACT FROM AUTHOR]

Copper/steel composite is a kind of composite with excellent performance and broad application prospects. In this paper, the micro-morphology and structure of the interface of copper/steel composite prepared by the hot-dip casting were observed by scanning electron microscope and transmission electron microscope, and the formation mechanism of the interface area was explored. The results show that the hot-dip casting temperature has a great influence on the micro-structure and morphology of the copper/steel interface area. When the hot-dip casting temperature is lower than 1125 °C, the copper/steel interface area is basically in a straight line. Even if the hot-dip casting time is extended, the interface characteristics change little. At 1100 °C, the copper-rich phase precipitated at the interface area is the coherent precipitates of Cu and BCC-Fe, with the crystal orientation <110> and the diameter about 10 nm ~ 30 nm. When the hot-dip casting temperature reaches 1150 °C, the copper/steel interface area begins to appear new micro-morphology, and the range of new micro-morphology becomes larger and larger with the increase in the hot-dip casting temperature and the extension of the hot-dip casting time. At 1200 °C, the copper-rich phase precipitated at the interface is the coherent precipitates of FCC-Cu and FCC-Fe, with the crystal orientation <100> and the size similar to that at 1100 °C. In the process of the hot-dip casting, the formation of the copper/steel interface area experienced three stages: the co-temperature of copper/steel and the wetting of copper liquid on solid steel, the formation and transformation of the solid–liquid mixed layer between steel and copper liquid and the evolution stage of the liquid–solid mixed layer during cooling and solidification. This kind of interface zone with gradual structure tightly connects the steel matrix and solidified copper together, to form a copper/steel composite with strong bonding. [ABSTRACT FROM AUTHOR]

Due to the excellent thermoelectric properties and low sintering temperature, nano-Ag paste is a promising die-attach material for high power electronic device. Unfortunately, it is difficult to resolve the critical issues including poor interfacial wettability, high porosity and poor high-temperature reliability of sintered nano-Ag joint. In this study, a novel bonding method was proposed to solve these problems by introducing Sn into the nano-Ag joint through the transient-liquid-phase (TLP) bonding technology. The Ag-Sn joint reported in this paper maintained excellent mechanical properties after high temperature aging and thermal shock test. The addition of Sn reduced the porosity of nano-Ag joint and improved the wettability of bonded interface. After aging at 200 °C for 2000 h, the shear strength still remains higher than 50 MPa. Besides, this bonding approach resolves the oxidization problem of Cu substrate at high temperature. The molecular dynamics (MD) simulation results indicate the addition of Sn could effectively inhibit the permeation of oxygen into the interface. [ABSTRACT FROM AUTHOR]

In this paper, we proposed rapid laser-induced synthesis of copper micropatterns on the surface of oxide glass from deep eutectic solvents (DESs) consisting of choline chloride, citric or tartaric acid, and copper acetate as the copper plating solutions. It was shown that upon the 532-nm continuos wave laser irradiation, it is possible to increase the deposition rate of copper and create micropatterns with a resistance close to the value of pure metal together with high adhesion to the substrate surface. This metallization method is favorable for the practical use of copper patterns, including in the production of new printable microelectronic devices. Thus, we demonstrated the possibility of copper deposition on arbitrary three-dimensional surfaces. Moreover, the resulting copper micropatterns were tested as working electrodes for non-enzymatic glucose. Finally, the proposed technology can be successfully used for the design and development of sensor platforms for the electrochemical analysis and microelectronic devices. [ABSTRACT FROM AUTHOR]

The effect of Ni in Ag–Cu filler on the wetting and brazing characterization of stainless steel was studied by means of wetting test and brazing test under high vacuum condition. The wettability of filler metal and the joint strength were improved after adding Ni in Ag–Cu filler. The filler penetrates into stainless steel and the topmost steel grains separate from the substrate, exposing the metal surface without oxide film after adding Ni, which leads to the reduction in contact angle. The interdiffusion between FM and SS is enhanced after adding Ni, which leads to further reduction in contact angle. At wetting temperature, large amount of Ni in liquid enriched at solid–liquid interface, increasing the Cu content in liquid near the interface to form Cu-rich liquid, which caused the penetration of liquid filler. Cu first penetrates into steel grain boundary, which provides a path for Ni diffusion into stainless steel. After the oxide film was removed, a large number of Ni directly diffused into stainless steel to form (γ-Fe, Ni) layer on stainless steel surface. Cu in liquid can directly diffuse into (γ-Fe, Ni). Stainless steel can dissolve in Cu-rich liquid with high Ni content. In the absence of Ni, FM/SS interface is the weakest location of the joint. After adding Ni in filler, the formation of Cu solid solution at FM/SS interface and the enhancement of interdiffusion between FM and SS strengthen the FM/SS interface, leading to the increase in joint strength. The results in this paper suggest Ni is beneficial for brazing stainless steel by Ag–Cu alloy. [ABSTRACT FROM AUTHOR]

In this paper, the mechanical damage behavior is investigated based on the characteristic roughness on the surface and the orientation of superficial structures. The main goal is to explore the surface roughness on mechanically loaded copper conductors as a lifetime indicator. For this purpose, copper conductors are mechanically stressed in accordance with EN 50,396 and then examined metallographically and microscopically. The microstructure examination shows that the roughness is caused by material extrusion and cracks due to work hardening in the surface area. Using confocal microscopy, it is shown for the first time that significant formation of surface roughness takes place over the service life of copper conductors. The roughness increases monotonically, but not linearly with number of cycles, due to internal microstructural processes and can be divided into three sections. First inspections of the conductor surface over lifetime show a correlation between the intensity of structures orientated 45° to the loading direction and the roughness. This phenomenon, already known from microscopic slip lines, is thus also evident in macroscopic roughness formation and is well founded by the research theory on material extrusion along dislocation lines. In summary, a lifetime determination is possible based on its developing roughness which enables the utilization as a sensor element. [ABSTRACT FROM AUTHOR]

In this paper, 50 ... 680 nm thick AlN-Al2O3 coatings are deposited by magnetron sputtering on the surface of a steel substrate and a piece of copper is melted on top of the ceramic. Upon heating the ceramic layer is cracked, and the phase inversion of the two top phases from steel/ceramic/copper configuration to the steel/copper/ceramic configuration takes place within 30 s of liquid time of copper. This phase inversion process is accompanied by a Gibbs energy change of about − 1.78 J/m2, due to good wettability of solid deoxidized steel by liquid copper in contrary to poor wettability of the ceramic by the copper. When copper is melted on AlN-Al2O3 coating with its thicknesses smaller than a critical value of about 170 ± 60 nm, liquid copper droplets hanging down into the cracks within the ceramic reach the solid steel surface at the bottom of the cracks, thus the flow of Cu down along the cracks is enabled. However, when copper is melted on AlN-Al2O3 with its thickness larger than the critical value of 170 ± 60 nm, Cu first forms a non-wetting droplet on top of the ceramics, and only after a certain incubation time it starts flowing down the cracks. This incubation time was found to depend linearly on the thickness of the ceramic, as cracks are filled from the bottom upwards by liquid copper via the evaporation–condensation mechanism. By the end of the process, the steel/copper/ceramic configuration is further stabilized by gravity. [ABSTRACT FROM AUTHOR]

Copper/diamond composites have drawn lots of attention in the last few decades, due to its potential high thermal conductivity and promising applications in high-power electronic devices. However, the bottlenecks for their practical application are high manufacturing/machining cost and uncontrollable thermal performance affected by the interface characteristics, and the interface thermal conductance mechanisms are still unclear. In this paper, we reviewed the recent research works carried out on this topic, and this primarily includes (1) evaluating the commonly acknowledged principles for acquiring high thermal conductivity of copper/diamond composites that are produced by different processing methods; (2) addressing the factors that influence the thermal conductivity of copper/diamond composites; and (3) elaborating the interface thermal conductance problem to increase the understanding of thermal transferring mechanisms in the boundary area and provide necessary guidance for future designing the composite interface structure. The links between the composite's interface thermal conductance and thermal conductivity, which are built quantitatively via the developed models, were also reviewed in the last part. [ABSTRACT FROM AUTHOR]

With the microelectronics technology going toward its physical limits and the emergence of three-dimensional chip stack architectures, now more than ever there are both needs and opportunities for novel materials to help address some of these pressing thermal management challenges. In this paper, a high-thermal-conductivity insulative SiO2-coated nano-Cu particle is prepared for new-type underfill materials of high-performance microelectronics packaging. It was found that nano-Cu can be successfully coated with SiO2 by using the surface modification between cetyltrimethyl ammonium bromide and silane coupling agent although nano-Cu particles have silicon-disordered property during the coating process of tetraethyl orthosilicate hydrolysis. Moreover, the thermal conductivity of epoxy mixed with nano-Cu@SiO2 as the packaging underfill is dramatically increased from 0.15 W/m K of the pure-EP and 0.60 W/m K of the EP/SiO2 to 2.9 W/m K due to electronic heat transfer, heat network and fast heat transfer center. It effectively releases the heat generated by the IC device, and the service life of the device is significantly improved from 63 min of pure-EP and 350 min of the EP/nano-SiO2 to 1039 min. The new material creates a challenging environment for keeping modern electronic devices cool, a critical factor in determining their speed, efficiency and reliability. [ABSTRACT FROM AUTHOR]

InGaN/GaN multi-quantum well light-emitting diodes (LEDs) are conventionally grown on a sapphire substrate due to a lack of compatible substrates with a high compressive strain. This is a result of the relatively large lattice, and thermal expansion coefficient mismatches between GaN and sapphire. The compressive strain is considered to be a major obstacle to further improve next-generation high-performance GaN-based LEDs. In this paper, we have designed, electroplated, and tested an efficient substrate using a patterned copper (Cu) layer on the backside of sapphire to relax the compressive strain in a GaN epilayer. The patterned Cu layer has a significant function in that it supports the GaN/sapphire LEDs with an external tensile stress. The external tensile stress is capable of compensating for the compressive strain in the GaN/sapphire LEDs by controlling the curvature of the wafer bowing. This patterned Cu layer, when applied to the GaN/sapphire LEDs, suppresses the compressive strain by up to 0.28 GPa. The GaN-based LEDs on this innovative and effective sapphire/Cu substrate offer improved optical and electrical performance. [ABSTRACT FROM AUTHOR]

Femtosecond laser surface processing (FLSP) is a technique that can be used to modify surfaces imparting many desirable properties, such as an improved wettability, heat transfer, and drag reduction. The morphology of the FLSP surface along with surface chemistry is critical factors that strongly influences the wetting behavior of surfaces produced. Reproducing the FLSP original surface over a large area in an economic manner is a challenge. In this paper, imprinting the FLSP surface on oxygen-free copper is investigated. Based on the topology of an FLSP titanium surface, a model has been established to investigate the topology of the mounds, which is defined by the roughness and period between the self-organized structures. This topology affects the imprint quality indicated by the plastic deformation in the blank and is defined as the target material specimen. Both oxygen-free copper and stainless steel 304 were used as blank target material in this study and represent both soft and hard material specimens. The stress-displacement relationship was used to determine the sensitivity of imprint parameters. The imprint model was verified by comparing an equivalent imprint model with nanoindentation experimental results. The model results showed that the die's morphology, in particular the die roughness-to-period ratio (referring to the peak-to-valley height and the peak-to-peak distance), had greater influence than the blank material itself. [ABSTRACT FROM AUTHOR]

The novel Mn-N alloyed lean duplex stainless steels with different addition of Cu were fabricated and studied in this paper. The effects of Cu addition, solid solution treatments and second phase precipitation on resistance to pitting corrosion were discussed in detail. The addition of 0.5% Cu can significantly improve the resistance to pitting corrosion due to that Cu can increase the activity of alloying Cr and facilitate the diffusion of Cr into ferrite phase, leading to the concentration of alloying Cr in ferrite phase. The corrosion resistance of present steels was decreased with the increase in solid solution treatment temperature from 1000 to 1150 °C due to the increasing difference of pitting corrosion resistivity between ferrite and austenite. The second phase precipitation of CrN can consume the beneficial elements of Cr and N in ferrite, leading to a dramatic decrease in corrosion resistance. The pitting potential of the present steel was sensitive to the aging treatments, and it was continuously decreased with the increase in aging time. [ABSTRACT FROM AUTHOR]

The paper focuses on thermal and electrical properties of copper-graphite composites. Copper-graphite composites in the range of 0-50 vol% of graphite were prepared from the mixture of copper and graphite powder by the powder metallurgy method. Such composites combine high thermal and electrical conductivities provided by copper matrix and low thermal expansion coefficient and lubricating properties due to the graphite phase. We model thermal and electrical conductivities and thermal expansion coefficient using methods of micromechanics in connection with the material microstructure and measure these quantities experimentally to compare with the results of modeling. Cross-property connections between thermal and electrical properties of the composites are established and experimentally verified. [ABSTRACT FROM AUTHOR]

In this paper, copper coated carbon nanotubes (CNTs) was synthesized by decomposition of Cu(II) acetylacetonate (Cu(acac)2) in hydrogen atmosphere at 300 °C. The thickness of the copper coating was in nanoscale according to scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images, and Raman spectra indicated that certain intermediate bonds were formed between copper and the template CNTs. The crystalline structure of copper and its growth orientation were determined by X-ray diffraction (XRD) and selected area electron diffraction (SAED). The copper coating on CNTs had a face-centered cubic structure and its growth orientation was parallel to $$ (\bar 111) $$ planes. The method developed in this paper had the advantages of simplicity in both process control and experiment equipments, so that it might provide a possibility of large-scale production. [ABSTRACT FROM AUTHOR]

In this paper, (3-mercaptopropyl)trimethoxysilane (MPTS)- and copper-coated carbon fiber (M-Cu-CF) was obtained by electroless plating method. The M-Cu-CF was evaluated by FTIR, XRD, TGA, and SEM. It was found that the MPTS and Cu were coated on the fiber surface successfully. The M-Cu-CF was utilized as a conductive filler in silicone rubber (SR) for thermal and electrical conductivity applications and exhibited good dispersion and compatibility with the matrix. The effect of M-Cu-CF content on the thermal conductivity and volume resistivity of silicone rubber composites was investigated. The results showed that the thermal conductivity of the M-Cu-CF/SR composites reached 1.99 W (m K) with only 4.0 wt% filler loading, approximately 2.10 times higher than that of raw-CF/SR composites at the same loading. And with the increase of M-Cu-CF loading, the least volume resistivity of M-Cu-CF/SR composites was 3.5 × 10 Ω cm. [ABSTRACT FROM AUTHOR]

The paper presents proof of concept of a viable multilayer technology to enhance the performance of multifilar helix, receive-only satellite antennas. Approximately, 30-μm layers of polyether ether ketone (PEEK) were deposited onto the Cu filars of a single layer dielectrically loaded multifilar helix antenna using aqueous electrophoretic deposition (EPD). The PEEK coating was densified at ~400-420 °C in flowing N to prevent oxidation of the Cu filars. A second Cu metallisation was deposited onto the surface of the PEEK and the resulting antenna characterised. The multilayer antenna revealed a dual band response with peak radiation efficiencies >25 % and ~50 % increase in bandwidth. Multilayered surface architectures fabricated from PEEK using EPD, therefore, show great potential for the development of a broad range of high-performance multiband dielectrically loaded antennas whose peak frequencies may, in principle, be tuned by modifying the thickness of the PEEK layer. [ABSTRACT FROM AUTHOR]

In this study, microfibrillated cellulose (MFC) and dendritic copper were used as binder and conductive phase for the elaboration of self-standing conductive films and coatings. A filtration technique was used to prepare MFC/Cu films from particle dispersions in water and ethanol. In aqueous slurries copper oxidized and an additional corona treatment or the use of zinc particles as sacrificial anode were necessary to obtain films with conductivities ranging from 70 to 2500 S m-1, respectively. In ethanol-based MFC/Cu slurries, copper was subjected to limited oxidation. However, the low packing density of conductive particles (below the percolation threshold) led to resistive films which, after densification by calendering, displayed extremely high conductivities, up to 70000 S m-1. Aqueous MFC/Cu slurries were successfully used for the deposition of conductive coatings on copy paper by Mayer rod coating and screen printing, which were subsequently treated by corona discharge and calendering. The obtained coatings displayed intermediate conductivity (i.e. 95 and 570 S m-1 for rod coating and screen printing, respectively), which can be further increased using zinc particles or ethanol-based formulations. [ABSTRACT FROM AUTHOR]

CuO/CuFeO thin films were obtained on glass substrate by ex situ oxidation in air at 450 °C for 12 h from various starting metal/oxide nanocomposites by radio-frequency sputtering technique. The structure and microstructure of the films were examined using grazing incidence X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopies, X-ray photoelectron spectroscopy, and electron probe microanalysis. These studies reveal that a self-organized bi-layered microstructure with CuO (surface layer) and CuFeO (heart layer) was systematically obtained. Due to the porosity of the upper layer formed during annealing, an increase in total thickness of the film was observed and is directly correlated to the oxidation of the metallic copper content initially present in the as-deposited sample. A self-organization in two stacked layers CuO/CuFeO with various void fractions ranging from 0 to 41 % can be obtained by controlling the as-deposited elaboration step described in the part I of this paper. The highest porosities were observed for films deposited at low argon pressure and low target-to-substrate distance. Due to their specific self-organization in p- and n-type layers associated with their high porosity, such structured films exhibited the best electrical sensitivity to CO gas sensing. The obtained results demonstrated the importance of microstructure control to improve the response of sensing layers. [ABSTRACT FROM AUTHOR]

The aim of this paper is to synthesize a copper/chromium oxide composite material. The use of a chemical processing method like the Pechini method is the best approach to control the chemistry and the microstructure. Nevertheless, the standard Pechini method has to be modified to obtain this specific type of composite. In this work, we have adapted two steps. Firstly we have eliminated the step involving ethylene glycol and secondly a reduction step has been added at the end. The new method is now capable of obtaining a Cu/CrO composite with specific stoichiometric ratios and a grain size ranging from 0.1 to 1 μm. We have used chemical and microstructural analyses to validate this work. [ABSTRACT FROM AUTHOR]

In this paper, large-scale uniform silver and copper nano/microtubes with high length diameter ratios have been successfully synthesized by a facile approach, using low-cost nano-scale glass fibers as templates. The tubular structures can be obtained by reducing of Ag and Cu ions on the surface of the fibers, along with removing the templates. The samples are characterized by SEM and XRD. Results show the tubular structures are very uniform and the tubular walls are composed of densely coalesced crystalline nanoparticles of 30–50 nm. [ABSTRACT FROM AUTHOR]

Since the exact analytical solutions for rapid solidification process are available only for special boundary conditions, numerical techniques have to be applied for more general boundary conditions. In this paper we will describe a finite difference method for simulation of rapid solidification that is based on control volume methodology and interface-tracking technique. Heat transfer computer study will be realized for solidification with and without melt undercooling at the interface. Such numerical method will be applied for thermal history analysis of solidifying nickel on copper substrate. [ABSTRACT FROM AUTHOR]

The development of strongly cube textured Cu based substrates is important in the cost effective production of long lengths of high temperature superconducting cables. The present paper reports textures (deformation and recrystallisation) development in pure Cu, Cu–Al, Cu–Mn (with a solute content of 1–3 at.%) and Cu–35 at.% Ni alloys. [ABSTRACT FROM AUTHOR]

Gd3+ was chosen as a substitute for Bi3+ in BiNbO4 ceramics, and the substitution effects on the sintering performance and microwave dielectric properties were studied in this paper. The high temperature triclinic phase was observed only in the Bi0.98Gd0.02NbO4 ceramics when sintered at 920 °C. Both bulk densities and dielectric constant (εr) increased with the sintering temperature, while decreased with the Gd content. The quality factor ( Q) exhibited a correlation to the Gd content and the microstructures of Bi1− x Gd x NbO4 ceramics. At the sintering temperature of 900 °C, Bi0.992Gd0.008NbO4 ceramics exhibited microwave dielectric properties of εr ∼ 43.87, Q × f ∼ 16,852 GHz (at 4.3 GHz), and its temperature coefficient of resonant frequency (τf) was found to be near-to-zero. [ABSTRACT FROM AUTHOR]

The widespread use of titanium aluminide alloys will require effective joining techniques for primary fabrication and repair. One such technique is Transient Liquid Phase (TLP) bonding, which has been used to join titanium aluminide alloys. A successful TLP bonding process uses a copper-containing composite interlayer and thus introduces a small amount of copper into the alloy. Although even relatively small alloying additions can be detrimental to the oxidation resistance of titanium aluminide alloys, the amount of copper added to the alloy during the TLP bonding process has previously been shown to be neutral or beneficial to the isothermal oxidation resistance of the alloy. In this paper, a small amount of copper introduced during TLP bonding is shown to have no detrimental effect on the cyclic oxidation of Ti-48 at% Al-2 at% Cr-2 at% Nb. [ABSTRACT FROM AUTHOR]

The present paper describes a new direct chemical plating method of copper, called Dynamic Chemical Plating. This low cost technology is based on spraying separate aqueous solutions containing copper metallic ions and Borohydride reducing agent. It is able to plate chemical copper at 30 μm/h at room temperature and may be used as an industrial process for metallizing polymers and non-conductors in general. The copper plating dynamic parameters were studied as well as the substrate characteristics in order to be metallized. The wettability of the plastics surfaces and the use of a coupling agent plate, as an under-coat metallic layer, are major important parameters to start plating and increase the adhesion of metallic copper layer to the substrate. Effects of pre-treatment conditions such as corona discharge, the plating kinetics and electrical properties of the copper film are also investigated. [ABSTRACT FROM AUTHOR]

A correction to this paper has been published: https://doi.org/10.1007/s10853-021-06031-9 [ABSTRACT FROM AUTHOR]

Cuprous oxide (Cu2O) nano- and microstructures possess unique properties that may find a variety of applications. Environmentally benign synthesis of Cu2O with well-controlled morphology is highly desirable. In this study, Cu2O crystals with tunable shapes are synthesized using cellulose nanofibrils (CNFs) as a shape regulator and the sole reducing agent in aqueous environment. By simply increasing Cu2O precursor concentration, the Cu2O crystals evolved from octahedra to cuboctahedra, and finally cubes, accompanied with increasing size from nano- to microscale. The selection of Cu chelating agent (sodium tartrate or potassium sodium tartrate) affected the crystal growth rate. Transition in the relative intensities of the (111) and the (200) crystalline peaks in their XRD patterns was consistent with the morphology change. During the growth of crystals, CNFs were preferably bound to the {111} crystalline facet. The introduction of KBr to the reaction system produced short hexapods. The resultant CNF-Cu2O hybrids were incorporated into waterborne polyurethane (WPU) films. Even with 0.5 wt% CNF-Cu2O, the WPU film showed significant enhancement in modulus, strength and elongation at break. This work proves the possibility of controlled growth of Cu2O particles aided by CNFs and provides a new strategy for improving the performance of eco-friendly WPU films. [ABSTRACT FROM AUTHOR]