Search

A Ka-band sheet electron beam (SEB) traveling-wave tube (TWT) based on three-slot staggered-ladder (TSTL) coupled-cavity slow-wave structure (CC-SWS) is proposed. The high-frequency characteristics of TSTL SWS were analyzed in detail. A well-matched input/output coupling system that solves the problem of energy coupling between the SWS and the external circuit was designed. A new method of loading the distributed attenuator for TSTL SWS was investigated for suppressing backward wave oscillation effectively. In addition, a SEB gun which can produce the SEB conveniently was optimized. A small tunable periodic cusped magnet (STPCM) system was designed to focus the low voltage, high-current SEB, which decreases the whole dimension of the TWT sufficiently. Moreover, the special STPCM system is predicted to exhibit 100% beam transmission efficiency. Finally, the beam-wave interaction was studied. The results obtained by CST simulation show that the SEB TWT can produce output power over 5 kW within the bandwidth ranging from 31.5 to 35.5 GHz, and the maximum output power is 10.15 kW at 33 GHz, corresponding electron efficiency of 10.36%. The fabrication of the device is under way. [ABSTRACT FROM PUBLISHER]

A 140-GHz folded-waveguide traveling wave tube (FWG-TWT) with a relatively larger circular electron beam tunnel was designed and developed. Using simulation software, the high frequency characteristics, the transfer characteristics, and the beam-wave interaction of the TWT were studied in detail. The simulation predicted up to 98 W output power and about 43 dB gain of FWG-TWT at the center frequency. The input and output couplers compatible with the FWG-SWS and the periodic permanent magnet focusing structure were designed. The FWG-TWT thus designed was fabricated and tested. The experimental result shows the output power exceeding 1.6 W and the gain exceeding 25 dB at 140 GHz when the input power is 5 mW. The reasons for the departure of the experimental from the simulated results have been explained. [ABSTRACT FROM PUBLISHER]

A new slow wave structure (SWS), named E-plane loaded sine waveguide (EPLSW) SWS is proposed for the development of G-band traveling wave tubes (TWTs). The structure, derived from the sine waveguide (SW) SWS, features staggered rectangular gratings on the two E-planes, intersecting with the sine-shaped gratings. The natural electron beam tunnel lies between these gratings. The EPLSW-SWS offers improved characteristics compared to the conventional SW-SWS. High-frequency simulation studies reveal that the passband of the EPLSW-SWS extends by more than 33 GHz over the SW-SWS under identical dispersion conditions. Additionally, the interaction impedance of EPLSW-SWS surpasses that of the SW-SWS in the frequency range of 195–255 GHz. Further analysis through particle-in-cell (PIC) results presents that when operating at 19.5 kV and 145 mA for the sheet beam current, it attains a maximum saturated power of 132.7W and a 3 dB bandwidth exceeding 50 GHz. [ABSTRACT FROM AUTHOR]

In order to improve the performance of sine waveguide (SW) traveling wave tube (TWT), an elliptical beam-tunnel sine waveguide (EBTSW) slow wave structure (SWS) is proposed. EBTSW-SWS not only has high interaction impedance in a relatively wide frequency band but also has an elliptical beam-tunnel. The simulation results of high-frequency characteristics show that, under the same dispersion, the passband of EBTSW-SWS increases by 30% compared to the SW-SWS, and the average interaction impedance of EBTSW-SWS is higher than that of SW-SWS in almost the whole passband. Moreover, the particle-in-cell (PIC) simulation results reveal that under the operating voltage of 20.8 kV and beam current of 150 mA, EBTSW-TWT can provide more than 70 W of saturated output power in the frequency range of 200-260 GHz, reaching the maximum power of 151 W at 220 GHz with the maximum electronic efficiency of 4.85%. [ABSTRACT FROM AUTHOR]

In order to alleviate the problem of achieving large powers beyond 10 kW at frequencies as high as 220 GHz, a two-stage, two-sheet-beam relativistic TWT (SBRTWT) was proposed. For one-stage SBRTWT, there exists instability phenomenon as the effect of electron noise will become large enough compared with the small input power. To avoid the effect, the gain of the first-stage tube was decreased, and its output power was employed to drive the second-stage tube. A large-width branch-guide energy coupler was proposed, analyzed and designed, which can solve the difficult problem to couple the amplified microwave from a wide waveguide to another wide waveguide. A two-beam SBRTWT of 70 kW output with a gain of 28.5 dB was predicted. The findings establish that the two-stage configuration provides larger output powers than the single-stage configuration of SBRTWT and call for further research in two-stage SBRTWT. [ABSTRACT FROM PUBLISHER]

A dual-beam planar slow wave structure (SWS), named dielectric supported ring-bar SWS is proposed in this paper. The planar SWS is supported by two dielectric rods at the side edges, making it fit for dual sheet beam operation. The high frequency and transmission characteristics of the proposed SWS are investigated. The backward-wave oscillation and higher harmonic waves are effectively suppressed by setting two cathodes in the same plane parallel to the SWS and negative phase-velocity jumping. The hot performance of the proposed SWS is carried out by using particle-in-cell (PIC) simulation, in which two sheet electron beams (9.7 kV, 0.2 A) are employed to provide direct current power. With an input power of 1W, the output power is 180 W at 38 GHz and the corresponding gain is 22.6 dB. Besides, after adding dielectric rods to the output part, the entire structure dissipates heat well by thermal analysis. [ABSTRACT FROM AUTHOR]

In order to further improve the output power of W-band traveling wave tube (TWT), a low gain TWT was proposed as a secondary amplifier. It uses a double staggered grating slow wave structure (DSG-SWS) and a sheet beam. Firstly, the design of DSG-TWT was given. Through simulation, the DSG-TWT could provide a saturation output power of more than 1000 W in the frequency range of 93–97 GHz, and the maximum output power could reach 1200 W at 95 GHz. No oscillation and current interception were found. Then DSG-SWS was fabricated by E-plane partition method using high-precision CNC milling. The SWS was fed with a high-power input-output coupler which consists of a mode converter and an impedance transformer. Simulation and cold-test results were presented, showing that the S11 is less than −10 dB and the voltage standing wave ratio (VSWR) is less than 2.0 in the frequency range of 93–100 GHz. [ABSTRACT FROM AUTHOR]