Search

Cold-formed steel (CFS) is a popular form of construction in New Zealand and the developed world because it can be cost-effective, durable, sustainable, resilient to extreme environmental and seismic loads and easy to install. When used in domestic and medium-rise buildings, T-Stub connection between CFS channel sections is formed by using self-drilling screws which connect the flanges. In the literature, no prior investigation on the tension capacity of such connection has been reported. Therefore, this paper describes a novel test procedure for determining the tension capacity of such CFS T-Stub connection and the associated mechanism of failure. An experimental test program that comprises thirty experimental tests is reported in this paper. Three channel section thicknesses were examined: 0.55 mm, 0.75 mm, and 0.95 mm. All specimens failed as a result of tilting of the screws and bearing failure. Non-linear elasto-plastic finite element (FE) models were developed, and the predictions were validated against the experimental test results. It was adjudged that there was reasonable agreement in terms of connection strength and failure mode prediction. Finally, the design strengths derived from current design standards were compared with the experimental failure loads. It was found that the American Iron and Steel Institute (AISI 2016) and Australian and New Zealand Standard (AS/NZS 2018) are conservative by 6% and unconservative by 10% for the initial and final failure loads of T-Stub CFS connections, respectively. • A novel cold-formed steel T-stub connection was studied experimentally and numerically. • The results of a total of 30 new experimental tests were reported. • Finite element analysis was conducted and validated against the test results. • The prediction accuracy of current design standards was evaluated. [ABSTRACT FROM AUTHOR]

This paper reports laboratory testing and numerical modelling on the cross-sectional behaviour and resistances of press-braked S690 high strength steel slender channel section stub columns under combined compression and minor-axis bending. A testing programme, including initial geometric imperfection measurements and ten minor-axis eccentric compression tests, was firstly conducted. This was accompanied by a numerical modelling programme, including a validation study, where finite element models were developed and validated against test results, and a series of parametric studies, where the validated finite element models were used to generate further numerical data. The obtained test and numerical data were then adopted to evaluate the current codified design interaction curves for press-braked S690 high strength steel slender channel section stub columns under combined compression and minor-axis bending, as provided in the European code, North American specification and Australian/New Zealand standard. The evaluation results revealed that the codified design interaction curves led to conservative and scattered resistance predictions, mainly due to the conservative end points (i.e. the cross-section compression and bending resistances). Finally, a new design interaction curve, anchored to more accurate end points, was proposed and shown to result in a higher level of design accuracy and consistency than the codified design interaction curves. • The behaviour of S690 high strength steel slender channel sections under minor-axis combined loading was studied. • Minor-axis eccentric compression tests were carried out. • FE models were developed and validated against the test results and then used to perform parametric studies. • The codified design interaction curves were evaluated, revealing a high level of conservatism. • A new interaction curve, anchored to the CSM end points, was proposed and shown to yield higher design accuracy. [ABSTRACT FROM AUTHOR]

This paper presents an experimental and numerical study of eccentrically loaded circular recycled aggregate concrete-filled stainless steel tube (RACFSST) stub columns. The testing programme was conducted on twelve specimens designed with different stainless steel tube section sizes and recycled coarse aggregate replacement ratios, and included tensile coupon tests, concrete cylinder tests and eccentric compression tests. The test results, including the failure loads and modes, load–mid-height lateral deflection curves and evolution of neutral axis, were reported and discussed. Following the testing programme, a numerical modelling programme was conducted, with finite element models developed and validated against the test results and then employed to perform parametric studies to generate further numerical data. The confinement effects were analysed based on the numerical data. The relevant design interaction curves, as set out in the European code, American specification and Australian/New Zealand standard, were assessed for their applicability to circular RACFSST stub columns under combined compression and bending. On the basis of the quantitative and graphical assessments, it has been found that (i) each set of codified design interaction curve leads to similar assessment results for eccentrically loaded circular RACFSST stub columns with different recycled coarse aggregate replacement ratios and (ii) the failure load predictions from the codified design interaction curves are conservative. • The structural behaviour and resistance of circular RACFSST stub columns under combined loading are investigated. • Twelve eccentric compression tests are conducted. • FE models are developed to validate against the test results and then used to conduct parametric studies. • The confinement effects of different types of RACFSST composite sections are discussed. • The applicability of the relevant codified N–M interaction curves is evaluated. [ABSTRACT FROM AUTHOR]

Cold-formed steel (CFS) back-to-back channels are becoming a popular choice for use in load-carrying members in building structures. These built-up channels often include web holes for installation of services. Traditional web holes are un-stiffened, which can restrict the size and spacing of holes. Recently, a new generation of CFS channels with edge-stiffened holes has been developed and used widely in New Zealand. No research has been reported in the literature to investigate the axial strength of back-to-back channels with edge-stiffened holes. Experiments are required on back-to-back channels with edge-stiffened holes so to understand the effects of composite actions between the back-to-back channels on the axial strength of such channels. This paper presents a total of 162 new results comprising 27 axial compression tests and 135 finite element analysis (FEA) results on the axial strength of back-to-back channels with edge-stiffened holes, un-stiffened holes and plain webs. Prior to compression tests, initial geometric imperfections were measured using a laser scanner. Tensile coupon tests were also conducted to determine the material properties of both the flat and corner portions of the channels. The test results show that for the case of back-to-back channels with edge-stiffened holes, the axial strength increased by 6.6% on average, compared to a back-to-back plain channel. For comparison, the same section with un-stiffened holes had a 12.4% reduction on average in axial strength, compared to a back-to-back plain channel. A nonlinear elasto-plastic finite element (FE) model was then developed, and the results showed good agreement with the test results. The validated FE model was used to conduct a parametric study involving 135 FE models to investigate the effects of column slenderness, diameter of hole, screw spacing, stiffener lengths and stiffener fillet radius on the axial strength of such channels. Finally, the tests and parametric study results were compared against the design strengths calculated in accordance with the American Iron and Steel Institute (AISI) (2016) and Australian and New Zealand Standards (AS/NZS) (2018) for back-to-back plain channels and against the design equations of Moen and Schafer (2011) for back-to-back channels with un-stiffened holes. It was found that the AISI (2016) and AS/NZS (2018) are only 3% conservative to the test results. The Moen and Schafer equations (2008, 2009, 2011) are conservative by 21% on average for back-to-back channels with un-stiffened holes. Deformed shapes at failure from experiments and FEA. Unlabelled Image • A new generation of back-to-back CFS channels with edge-stiffened holes is examined. • Results from an experimental regime and elasto-plastic finite element are reported. • A parametric study involving 135 FE models was conducted. • Variables included column slenderness, hole size, screw spacing, stiffener lengths and stiffener fillet radius. • Edge stiffened hole-channels can outperform plain channels in terms of axial strength. [ABSTRACT FROM AUTHOR]