Search

Cold-formed steel (CFS) is a popular form of construction in New Zealand and the developed world because it can be cost-effective, durable, sustainable, resilient to extreme environmental and seismic loads and easy to install. When used in domestic and medium-rise buildings, T-Stub connection between CFS channel sections is formed by using self-drilling screws which connect the flanges. In the literature, no prior investigation on the tension capacity of such connection has been reported. Therefore, this paper describes a novel test procedure for determining the tension capacity of such CFS T-Stub connection and the associated mechanism of failure. An experimental test program that comprises thirty experimental tests is reported in this paper. Three channel section thicknesses were examined: 0.55 mm, 0.75 mm, and 0.95 mm. All specimens failed as a result of tilting of the screws and bearing failure. Non-linear elasto-plastic finite element (FE) models were developed, and the predictions were validated against the experimental test results. It was adjudged that there was reasonable agreement in terms of connection strength and failure mode prediction. Finally, the design strengths derived from current design standards were compared with the experimental failure loads. It was found that the American Iron and Steel Institute (AISI 2016) and Australian and New Zealand Standard (AS/NZS 2018) are conservative by 6% and unconservative by 10% for the initial and final failure loads of T-Stub CFS connections, respectively. • A novel cold-formed steel T-stub connection was studied experimentally and numerically. • The results of a total of 30 new experimental tests were reported. • Finite element analysis was conducted and validated against the test results. • The prediction accuracy of current design standards was evaluated. [ABSTRACT FROM AUTHOR]

Built-up box sections are becoming increasingly popular for column members in cold-formed steel (CFS) construction; uses of such sections include CFS trusses, space frames, and portal frames. In this article, the built-up box sections are formed through two identical lipped channels connected at their flanges with self-drilling screws. In such an arrangement, independent buckling of the individual channels is prevented by the screws. This paper presents an experimental investigation on axial capacity of built-up CFS box sections. Tests were conducted for different values of slenderness from short to slender columns. In total, the results from 16 experimental tests are reported. Of these, 8 tests were conducted on built-up CFS box sections and the remaining 8 tests were conducted on single channel sections. Load-axial shortening relationship, and failure modes are discussed for built-up columns. Nonlinear finite element (FE) models were developed for built-up CFS box sections and single channels. FE models considered material nonlinearities, initial imperfections and modeling of intermediate fasteners. FE results showed good agreement against the test results. A parametric study was conducted which comprises 148 models to investigate the effect of fastener spacing on axial capacity of built-up CFS box sections. Both FE and test results were compared against the design strengths calculated in accordance with the American Iron and Steel Institute (AISI) and Australian and New Zealand Standards (AS/NZS). From the comparison, it was observed that the AISI & AS/NZS are conservative by around 17% while determining the axial capacity of such built-up CFS box columns. • Experimental tests were conducted on CFS built-up box sections under axial compression. • Results from an experimental regime and elasto-plastic finite element are reported. • Local and overall imperfections are considered in FE models • The validated FE model was used for a parametric study to investigate the effect of screw spacing. • The design strengths in accordance with the AISI & AS/NZS are conservative by around 17% for CFS built-up box columns [ABSTRACT FROM AUTHOR]

Cold-formed steel (CFS) back-to-back channels are becoming a popular choice for use in load-carrying members in building structures. These built-up channels often include web holes for installation of services. Traditional web holes are un-stiffened, which can restrict the size and spacing of holes. Recently, a new generation of CFS channels with edge-stiffened holes has been developed and used widely in New Zealand. No research has been reported in the literature to investigate the axial strength of back-to-back channels with edge-stiffened holes. Experiments are required on back-to-back channels with edge-stiffened holes so to understand the effects of composite actions between the back-to-back channels on the axial strength of such channels. This paper presents a total of 162 new results comprising 27 axial compression tests and 135 finite element analysis (FEA) results on the axial strength of back-to-back channels with edge-stiffened holes, un-stiffened holes and plain webs. Prior to compression tests, initial geometric imperfections were measured using a laser scanner. Tensile coupon tests were also conducted to determine the material properties of both the flat and corner portions of the channels. The test results show that for the case of back-to-back channels with edge-stiffened holes, the axial strength increased by 6.6% on average, compared to a back-to-back plain channel. For comparison, the same section with un-stiffened holes had a 12.4% reduction on average in axial strength, compared to a back-to-back plain channel. A nonlinear elasto-plastic finite element (FE) model was then developed, and the results showed good agreement with the test results. The validated FE model was used to conduct a parametric study involving 135 FE models to investigate the effects of column slenderness, diameter of hole, screw spacing, stiffener lengths and stiffener fillet radius on the axial strength of such channels. Finally, the tests and parametric study results were compared against the design strengths calculated in accordance with the American Iron and Steel Institute (AISI) (2016) and Australian and New Zealand Standards (AS/NZS) (2018) for back-to-back plain channels and against the design equations of Moen and Schafer (2011) for back-to-back channels with un-stiffened holes. It was found that the AISI (2016) and AS/NZS (2018) are only 3% conservative to the test results. The Moen and Schafer equations (2008, 2009, 2011) are conservative by 21% on average for back-to-back channels with un-stiffened holes. Deformed shapes at failure from experiments and FEA. Unlabelled Image • A new generation of back-to-back CFS channels with edge-stiffened holes is examined. • Results from an experimental regime and elasto-plastic finite element are reported. • A parametric study involving 135 FE models was conducted. • Variables included column slenderness, hole size, screw spacing, stiffener lengths and stiffener fillet radius. • Edge stiffened hole-channels can outperform plain channels in terms of axial strength. [ABSTRACT FROM AUTHOR]