Search

The advancement in plastic and plastic based products in last two decades has imposed a serious threat to the environment. This has led to an increase in the demand for sustainable and biobased products. Paper and paper products are good alternatives to their plastic counterparts. A key element of paper industry is the raw material (wood, bamboo and nonwood agricultural residues such as bagasse, straws etc.) from which pulp is produced. The pulp is then utilized for production of paper. There are many pulping processes to prepare pulp of various qualities. For fine grade pulp, chemical pulping is used. The chemical pulp is produced by soda, kraft and sulphite pulping processes. However, for newsprint grade pulp, stone ground wood (SW), thermomechanical (TMP), chemi-thermomechanical (CTMP), chemi-mechanical (CMP) or refiner mechanical (RMP) corresponding pulping processes are employed. The method of pulp preparation (pulping process) consumes large amount of energy and chemicals. A new pulping process with electron irradiation using biowaste (bagasse) as a raw material is discussed in this work. Bagasse pulping process is found to reduce about 50% of energy consumption during pulping process. The process is referred to as ‘ECTMP’ (Energy Efficient Chemi-Thermo Mechanical Pulping). The paper produced from aforesaid method also reflected no loss of strength properties with respect of TMP reference pulps. Henceforth, preliminary calculation based on experimental results shows that the proposed bagasse ECTMP process explored the scope of energy savings of the order of 50%.

Unprinting of paper can reduce multiple life-cycle stages in the recycling of paper to yield significant environmental impact. Laser-unprinting has been demonstrated for uncoated paper but causes significant damage to coated paper. This work explores a scalable optical (non-laser) process for unprinting coated paper. Printed coated paper is exposed to pulsed broad-spectrum Intense Pulsed Light (IPL) from a xenon lamp and the toner is then removed by dabbing gently with an ethanol wipe. While black toner is easily unprinted, unprinting of colored prints (red, blue, green) is best realized by incorporating an initial overprint of black toner. An unprinting throughput on the order of mm2/s is achieved. Three distinct regimes of unprinting are identified based on the extent of toner removal and damage of the paper. The optical properties of the unprinted paper, characterized via UV–Visible spectrophotometry, are correlated to these regimes to understand the potential for in-situ optical process monitoring. Scanning Electron Micrography and Fourier-Transform Infrared Spectroscopy are performed to understand the underlying mechanisms that govern the occurrence of the different unprinting regimes. Further, the potential impact of the developed approach on recycling of paper is discussed in the context of the capabilities of current optical unprinting approaches and the potential elimination of life-cycle stages in conventional paper recycling.

Microbial fuel cell is a promising technology to harvest energy from wastewater, and effective anode catalysts are essential for its applications. In this study, zero-dimension nitrogen-doped carbon dots, as biocompatible efficient modifiers, were synthesized and decorated onto the carbon paper surface to prepare microbial fuel cell anode. The as-fabricated nitrogen-doped carbon dots decorated carbon paper anode was able to enhance electricity generation and efficient wastewater treatment. It was found that the as-fabricated electrode had a high hydrophilicity, which was favorable for the microbial immobilization. Compared with the carbon paper anode, the biofilm on the as-prepared anode was almost twice of thickness. After introducing nitrogen-doped carbon dots, the extracellular electron transfer process from the microorganisms to the anode was enhanced. The microbial fuel cell with the as-developed anode generated a remarkable power output of 0.32 mW, 1.1 times higher than that of the raw carbon paper anode with same measurement area. Moreover, 16 sRNA pyrosequencing analysis shows that the quantity of Pseudomonas on the electrode increased by ∼40%, which also promoted the electron transfer rate by excreting mediators like phenazines or phenazine derivatives. This work developed a new approach to design microbial fuel cell anode material and fabricate a high-efficiency and environmentally friendly anode for electricity generation from wastewater.

The industrial solid waste generation and its stockpile disposal have major environmental consequences. These consequences could be minimized through the solid waste application as a raw material in other industries. The current study focusses on the utilization of lime sludge with boiler ash synthesized nanosilica for production of belite based clinker at relatively lower temperature. Lime sludge was also used in combination with fly ash and boiler ash to check the synthesis of compounds at varying temperatures. Nanosilica was synthesized from pretreated boiler ash through alkali treatment and acid precipitation. The synthesized nanosilica has been characterized for specific surface area, crystallinity, surface functional groups and size. Three different mixtures, containing lime sludge with nanosilica, fly ash, and boiler ash are fired at temperatures ranging from 900 °C to 1200 °C and characterized for the synthesis of belite. Conventionally, belite is synthesized above 1200 °C, whereas the combined application of lime sludge and nanosilica reduces the temperature of belite synthesis to 900 °C without pre calcination or addition of any chemical stabilizer. In the case of lime sludge and boiler ash blend, belite formation takes place at the higher temperature (1100–1200 °C). Anorthite synthesis takes place in case of lime sludge and fly ash blend, due to high percentage of alumina present in fly ash. Lime sludge and nanosilica based belite clinker are used to develop newer cementitious binder. Hydration and strength properties of developed binder proved worthy as building materials. This study will present alternatives for sustainable utilization of lime sludge, fly ash and boiler ash in construction.

Industrialization and urbanization are the key drivers to threaten the environmental quality and natural resources. Traditionally, pulp and paper industry has been highly reliant on forest based resources for its escalation. Shortage of forest based raw materials, strict environmental regulations and policies have compelled the industry to seek for alternate raw materials for its production. Mills are now focusing on exploring the potential of different agro wastes such as cereal straws and bagasse etc. In present research, sugarcane trash, one of the most abundant agro residues in India, was investigated for its capability in pulping and bleaching. Chemical characterization of sugarcane trash showed that it contains 40.4% cellulose, 33.2% hemicelluloses, 17.4% lignin and 6.45% ash content with 2.76% silica. To cook sugarcane trash with soda pulping method, 14% alkali charge, 15 min time and 162 °C temperature was found to be optimum and pulp of kappa no. 19.8 was prepared that exhibited good strength properties. Bleaching of pulp was carried out using elemental chlorine (Cl2), hypochlorite and chlorine dioxide (ClO2) based sequences. Replacement of Cl2 with ClO2 has significant impact on strength properties and effluent characteristics. Oxygen delignification stage was incorporated prior to ClO2 that resulted in improved optical properties of pulp with noticeable reduction in wastewater load. This paper elaborates the need of using sugarcane trash in paper mills with environment friendly pulping and bleaching processes to combat with the problem of waste management, wastewater load reduction during bleaching and substitute for wood based raw materials in papermaking.

This paper examines the mechanical properties and durability of recycled aggregate concrete (RAC) containing 100% coarse recycled concrete aggregate (RCA) and industrial by-products. The by-products, including waste paper sludge ash (PSA), fly ash (FA), silica fume (SF), and metakaolin (MK) of different proportions (5%, 10%, 15%) in RAC, were used in two methods: replacement and addition methods. The use of by-products (mineral admixtures) to mitigate the low quality of RAC was demonstrated through experimental outcomes in this study. The addition of industrial by-products was presented as a promising alternative for the addition of more Portland cement in RAC to enhance RAC's quality. The results showed that the strength and durability of RAC containing mineral admixtures in the addition method were higher than the addition of more cement or the replacement method. Notably, PSA considerably improved the mechanical properties of RAC at an early age, and it substantially improved the resistance of RAC to acid and sulfate attacks. At 90 days, FA and MK improved mechanical properties of RAC greater than SF and PSA did. Among combinations, the proportions of by-products in RAC of 5% PSA, 10% SF, 15% MK and 15% FA can produce the highest performance of RAC with 100% coarse recycled concrete aggregate (RCA).

Pulp and paper industry is one of the high priority sectors that generates large amount of solid (sludge) and liquid (paper mill effluent) wastes. Making use of this huge quantity of paper mill sludge (PMS) in an environment friendly manner is challenging and cost involving. Similarly the present wastewater treatment strategies based on physical and chemical methods encounter certain serious setbacks including secondary pollution generation with expensive mode of abatement processes. The present study aims at a “waste treats waste” strategy for the bioremediation of paper mill effluent in fluidized bed reactor (FBR) using another waste of the same industry, PMS as immobilizing matrix for Planococcus sp. TRC1, a wastewater bacterial isolate. This study simultaneously explores this isolate for the yellowish orange pigment it produces (2.3 ± 0.2 mg/gm of dry bacterial biomass) and characterizes it as a member of the pharmacologically important carotenoid pigment family via UV-Vis spectrophotometry, TLC, FT-IR and 13C NMR. The antioxidant potential of this pigment was studied by DPPH assay (IC50 = 33 ± 0.4 μg/ml) and H2O2 assay (IC50 = 147.4 ± 2.2 μg/ml). In FBR, the PMS immobilized bacteria showed removal of phenol, lignin, colour and COD from the effluent by 96%, 74%, 81% and 85% respectively after 60hr of treatment. The experimental data on immobilization fitted well with pseudo second-order (R2 = 0.955) and Freundlich adsorption isotherm (R2 = 0.996) models. The alterations in PMS before and after bacterial immobilization, as revealed by SEM and FT-IR, depicted the success of PMS as immobilization matrix. Phytotoxicity (90% seed germination) and mutagenicity studies confirmed that the treated effluent was substantially less toxic than its raw state. This study highlights a novel utilization possibility of PMS in an eco-friendly and economic way as immobilization matrix for Planococcus sp.TRC1 for paper pulp mill effluent treatment along with production of carotenoid pigment from this potential bacterial isolate as value added product.

The biological deinking method using microbial enzymes is quite promising and rather eco-friendly. In this paper, we discuss about the impact of enzymatic deinking of newspaper pulp using ligno-cellulosic (cellulase, xylanase and laccase) and lipolytic enzymes. The individual treatment of paper pulp with enzymes (cellulase/xylanase) could enhance the paper brightness to about 32.86% whereas combinational effect could enhance only about 28.67%. There was a release of chromophores from phenolic and hydrophobic compounds released during the deinking process. Physico-chemical parameters of effluents were also found to be within the standard limits and the metals like iron, lead and zinc were not detected in the enzyme assisted deinking effluent sample. The heavy metals in the paper pulp was found to be reduced after enzyme treatment. The obtained effluent was found have low phytotoxicity and was safe for agricultural applications. Hence, the present report was found to be a suitable enzymatic deinking process which was eco-friendly that results in non-toxic effluents. The method also provides an avenue in water resource recycling within industries.

To evaluate the effect of brown-rot fungi Oligoporus placenta and earthworm Eisenia fetida on decomposition of paper mill sludge, the paper mill sludge was mixed with cow dung in 0, 25, 50, 75, and 100% proportions and changes in physicochemical quality of waste mixtures was carried out for 28 days. All waste mixtures were treated with: Setup-I (E. fetida), Setup-II (O. placenta) and, Setup-III (E. fetida + O. placenta). A decrease in total organic carbon, C/N ratio and cellulose but an increase in total kjeldhal nitrogen, total phosphorus, total potassium and pH was recorded. The paper mill sludge in 50–75% proportion in feedstock showed the better results and rate of mineralisation were in order: Setup-III > Setup-I > Setup-II. The proportion of CD has direct role in waste mineralisation. The microbial population (bacterial, fungal and actinomycetes) and earthworm biomass were also high in Setup-III, suggesting the influence of brown-rot fungi on paper mill sludge humification. Results indicate that fungal inoculate in vermicomposting was effective in decomposing cellulose-rich industrial sludge.

Black liquor, an industrial waste, also generally called spent liquor is a promising feedstock for production of bio-carbon due to its high lignin and energy contents. Mild processing conditions and sustainable resource utilization can drive commercial utilization of this industrial waste. A novel oxidative procedure using hydrogen peroxide as a green liquid oxidant at room temperature for processing of paper recycling neutral sulphite semi-chemical spent liquor was established and evaluations were carried out for its efficiency. Standard hydrothermal carbonization was carried out for comparing bio-carbon production qualitatively and quantitatively using the same spent liquor. The oxidation procedure was performed at room temperature using 5% of H2O2 followed by washing in diluted sulfuric acid (0.15 N) while hydrothermal carbonization was performed at 250 °C. The bio-carbon produced were similar in terms of ash percentage and ranged from 1.25 ± 0.05 to 1.48 ± 0.05% for oxidation method and from 1.11 ± 0.03 to 1.45 ± 0.04% for hydrothermal carbonization. The carbon contents for the oxidation method ranged from 60.54 to 61.50% and 66.81–67.31% for hydrothermal carbonization while higher heating values ranged from 25.32 to 26.11 MJ/kg and from 28.68 to 29.34 MJ/kg respectively. The mass yield ranged from 29.98 to 31.88% by the oxidation, while it was 15.02–16.08% by hydrothermal carbonization.

The global demand for bio-plastic particularly polyhydroxyalkanoate (PHA) have been increased in the last few decades as a substitute of petrochemical-based plastic. Utilization of waste paper, the primary constituent of municipal solid waste (MSW), as a carbon source for polyhydroxybutyrate (PHB) production is not only an alternative, environmental friendly route of waste management but also helps to valorize the waste. In this study, hydrogen peroxide pretreated waste paper saccharification has been optimized using central composite design (CCD). The maximum hydrolysis (88.18%) occurred at paper loading 5.0 g/L, agitation 242 rpm, working volume 20%, cellulase 49.82 U/g, β-glucosidase 20.9 U/g and hemicellulase 29.5 U/g. PHB synthesis and biomass accumulation by xylose-utilizing Burkholderia sacchari using waste paper hydrolysate were studied using different nitrogen sources and carbon to nitrogen (C/N) ratios. Maximum PHB and dry cell weight (DCW) occurred with ammonium sulfate and a C/N ratio of 20. The highest biomass (3.63 g/L), the maximum PHB accumulation (44.2%) and the maximum reducing sugar utilization (92.1%) were observed after 48 h of cultivation using diluted hydrolysate. The physicochemical properties of the extracted PHB were compatible with the standard PHB. Hence, the waste paper could be exploited as a renewable feedstock for the sustainable production of PHB.

Building bricks were produced by utilizing deinking paper mill sludge (DPMS) and alluvial soil by varying percentage of sludge at different firing temperatures. Different mix proportions were prepared with 0%, 5%, 10%, 15%, 20%, 25% and 30% of DPMS incorporation in alluvial soil by weight. Three firing temperatures of 900 °C, 950 °C and 1000 °C were investigated to simulate the typical condition of kiln. The density, firing shrinkage, water absorption, efflorescence, apparent porosity, compressive strength and thermal conductivity of the bricks were determined. The XRD and microstructural analysis of brick specimens were also studied. The optimum firing temperature was 950 °C. The thermal conductivity decreases with increase in percentage of deinking paper mill sludge. It was found that 15% deinking paper mill sludge gives optimum strength at firing temperature of 950 °C. Developed bricks satisfy the requirements of class 10 of Bureau of Indian Standards (BIS), in terms of efflorescence, compressive strength and water absorption. Thermal conductivity results show that the developed brick was thermally more insulated than the conventional bricks and can be used as alternative to conventional bricks. This will address the issue of waste management through cleaner production and show the ways towards sustainable, economical and energy efficient construction.

The paper and cellulose manufacturing industry generates significant quantities of waste, including an extremely humid sludge, which is considered to be an effluent with high environmental liability for the manufacturer. Studies have shown that this waste sludge may be utilized in construction material, such as mortar for fixing blocks, as well as for ceiling and wall coatings that use ceramic masonry as a sealant. The recycling of pulp and paper industry waste sludge has important environmental benefits, by preventing soil and water pollution caused by inadequate disposal and by reducing the depletion of natural resources, such as lime, used in cementitious materials. This study analyzed the sustainability of incorporating such waste into cement-based mortars. Tests were conducted replacing lime, one of the most expensive mortar components with high environmental impact, with waste sludge in contents of 5%, 10%, 15%, and 20%. Analysis was then performed on the samples to assess the primary technical characteristics of these incorporated mortars, such as the consistency index, heat of hydration, content of incorporated air, water retention, mechanical strength and the capillarity coefficient. The results were compared with the results of the characterization tests that were performed on the waste material. The results showed that for use in wall and ceiling mortar coatings, the level of incorporation should not exceed 10%, because higher levels yield lower values of mechanical strength resistance, incompatible with market requirements. This result is probably due to the low heat of hydration of the waste material which generates slower reactions. On the other hand, higher levels of waste material content, above 10%, are appropriate convenient for mortar used to fill small repairs in masonry that do not require control of properties.

The increasing presence of e-books (electronic books) has become a major focus in countries around the world. In the United States, e-books represented 28% of the total book sales for 2012. In Japan, the conversion from paper books to e-books is expected to accelerate by the prevalent use of smartphones and tablet PCs. It is therefore important to quantitatively evaluate the environmental load of paper books and e-books for a sustainable society. In this study, paper books are compared to e-books read on different electronic devices (e-ink tablets, tablets, cell phones, smartphones, laptop computers, desktop computers and portable music players) through a case study on a 224-page book. The study is based on key primary data such as use time and reading speed for each device and aims to minimize assumptions made in other studies. GHG emissions for paper books are 1.24 kg-CO2e/book, and are reduced to 1.11 kg-CO2e/book when the effect of paper recycling is taken into consideration. The results for e-books under average use-time conditions range from 0.25 to 0.91 kg-CO2e/book with the e-ink tablet having the lowest emissions. When the average use time of each e-book device is applied, the paper book has a higher impact than all the e-books. However, sensitivity analysis shows that the impact of paper books can be lower than that of e-books for larger screen devices such as tablets, laptops and desktops when the reuse of books is considered or the e-book reading device is hardly used during its life cycle.

The aim of this study was to explore the potential of crude xylano-pectinolytic enzymes in bio-pulping of rice straw, in order to reduce environmental pollution. In this study, the effect of integration of bio-pulping strategy before chemical pulping of rice straw has been investigated. The bio-pulping efficiency was found to be maximum at xylanase:pectinase dose of 400:120 IU/g rice straw, temperature 55 °C, treatment time 3 h, Tween 80 (1%), pH 8.5 and pulping consistency 1:10 (g/mL). Bio-pulping enhanced the permeability of pulping chemicals, generated pulp with higher yield, brightness, along with higher residual active alkali content of black liquor in comparison to the pulp obtained after chemical pulping. Bio-pulping also resulted in 10% reduction of alkali dose and improved paper quality, with increase in breaking length (13.9%), burst index (27.0%), double fold (39.3%), gurley porosity (18.75%) and viscosity (8.77%) of unbleached bio-pulp. Bio-pulping also improved the bleachability by removing the D2 step of bleaching and produced pulp with higher physical strength properties, breaking length (15.92%), burst index (20.47%), tear index (3.87%), double fold (36.0%), gurley porosity (25.0%) and viscosity (28.36%). Hence, this environmentally sustainable bio-pulping approach can decrease the chemical load and ultimately pollution, along with enhance the yield and quality of paper. This is the first report demonstrating cleaner pulping of rice straw using crude xylano-pectinolytic enzymes, produced by a bacterial isolate.

In this study, a mathematical model has been developed for sustainable inventory, in which the effects of environmental factors on social factors, have been investigated. To this end, first, we revised Economic Order Quantity (EOQ) model by adding income from waste sales to this model. Next, considering the emission of sulfur oxides (SOx), nitrogen oxides (NOx) gases, Biochemical Oxygen Demand (BOD) and chemical oxygen demand (COD) indicators in waste water as a measure of water organic pollutants, we proposed a Green Economic Order Quantity (GEOQ) model. Then in order to examine interdependency between environmental aspects and social aspects, we introduced the sustainable model by adding environmental ergonomics in the terms of the effect of SO2 emission on human health. Since the structure of the model consists of nonlinear objective function and linear constraints, the model could be solved based on an exact nonlinear constrained solution method. Finally, we examined the effectiveness of the proposed model demonstrated in a real case study of pulp and paper mill. Validation of the model was done by comparing the cost function of the proposed model with the pure economic model and the actual data. The results of study showed that proposed sustainable model plays a significant role in determining the order quantity and reduction of cost function, sulfur oxides (SOx) and nitrogen oxides (NOx) emissions, and Biochemical Oxygen Demand (BOD) and chemical oxygen demand (COD) in waste water.

Waste paper, one of the major components of municipal and industrial wastes, has considerable potential as a low-cost inductive feedstock for enzyme production. In this study, four kinds of waste papers were used for simultaneous production of cellulase and xylanase by Trichoderma longiflorum. The highest FPase activities (3.21 IU/mL and 2.97 IU/mL) were achieved using waste office paper (WOP) and corrugated board (CB), respectively, followed by magazine paper (MP, 2.51 IU/mL) and tissue paper (TP, 2.34 IU/mL). The maximum β-glucosidase activities (0.51 IU/mL) and xylanase activities (382.59 IU/mL) were obtained from CB substrates, which were higher than that in the reported literature using waste paper. Correspondingly, the soluble protein concentrations and SDS-PAGE profiles from CB fermentation revealed that more enzymes were secreted during fermentation compared with other waste paper. Moreover, the structural features of different waste paper were characterized by using SEM and XRD technique and revealed that the structural variations were mainly caused by the raw wood sources and papermaking processes, and further affected the fermentation capacity. In addition, a higher β-glucosidase activity of 0.80 IU/mL were obtained from the mixed carbon source of CB and wheat bran (WB), which were significantly improved and increased by 56.86% when compared with the CB as single carbon source. This study confirmed that the waste paper without pretreatment could be efficiently utilized as an inductive feedstock for simultaneous production of cellulase and xylanase by T. longiflorum. Therefore, these findings obtained from this study will provide a more widely insight into investigating the low-cost inductive feedstock for enzyme production, which were of great benefit both for the economy and environment.

The need to view innovation policy through the lens of policy mixes has gained momentum given the growing complexity, the dynamics of real-world policy and the wide array of difficulties to address the current great societal challenges, notably the increasing pressure on the ecosystems that support our society. One of the main challenges concerning the transition towards bioeconomy, is to gain a more in-depth understanding on the policy mix to stimulate innovation in sustainability transitions. Our paper aims at enriching the portfolio of empirical case studies on policy mixes for innovation and sustainable transitions, by investigating the development of the policy mix underpinning the sustainability transition of the pulp and paper industry in Sweden. We apply a case study approach which draws on event history analysis, semi-structured interviews with industry and policy makers, literature reviews, a participative workshop with stakeholders from the pulp and paper industry, as well as on the IEA databases on climate change and energy efficiency policies and measures. Our analysis emphasises coordination, timing and scale in policy mixes as important elements to understand how instruments interact to accelerate sustainability transitions. The mapping of the policy mix shows that destabilising policies were crucial for accelerating the transition process of the industry. Prior to novelty creation policies, destabilising policies (e.g. environmental policies) were needed for 'innovation policy instruments' to be effective. More specific instruments (e.g. carbon tax), targeting particular functions of the innovation systems, require 'on-the-ground' policy intelligence and benefit from close interaction with industry.

Aeration, as a process in pulp and paper wastewater treatment, uses the greatest share of the energy. Therefore, if the energy efficiency of the treatment has to be improved, the focus must be on aeration. A key finding from the trials conducted for this paper, with effluent from a paper and pulp mill, was that the oxygen transfer coefficient could be doubled and the chemical oxygen demand could be decreased by 25%, if the effluent was pre-treated with 30 mg/l of aluminium coagulant (equivalent to 9.4 tonnes per day of AVR to 20000 cubic metres of effluent). Decrease in oxygen requirement implies decreases in aeration energy use. Pulp and paper mill effluents are not as biodegradable as municipal sewage, and the improvement in oxygen transfer properties of the effluent will have a positive influence over a longer period of time in the biological treatment. If the sludge is digested anaerobically, pre-treatment will also result in doubling the potential for methane generation. A holistic analysis of modifications to processes entails a study of the economic and environmental consequences as well. While the economic aspect is beyond the scope of this paper, only the net global warming as an environmental impact category has been studied, by taking recourse to specific emission coefficients. Of the four dosages of ferric aluminium sulphate considered in this analysis, the net greenhouse gas emissions are the least – 426 kg carbon dioxide equivalent per day when the daily consumption is 9.4 tonnes.

Reducing waste materials through reuse has in the recent past contributed to sustainable manufacturing in many industries. With the development of large-scale poultry farming, the treatment of large amounts of chicken feathers has become a problem and threatened its use as a renewable resource. This paper examines the use of chicken feathers in the paper making process; a process which would traditionally use wood as the raw material. The effects of combining feather fibre and wood pulp on paper performance were studied and compared to the properties of handsheets made with 100% wood pulp. With the increase of feather content, properties such as tightness, tensile index and bursting index decreased, whilst air permeability improved. There was no significant difference in water absorbency between various chicken feather/wood pulp handsheet samples however, the water absorbency started to decrease above 80% of chicken feather content. This could potentially open up a new avenue for the use of chicken feathers in applications that are meant to tolerate high humidity conditions, e.g., packaging products.

Utilization of the quality-upgraded waste paper in the manufacture of paper and board will reduce the wood consumption and pulping energy. While the optical property of the fibers from recycled old newspaper is very poor, in-situ calcium carbonate formation on those fibers by injecting carbon dioxide to the mixed slurry of those pulp and calcium oxide improved their brightness. Upgrading recycled old newspaper to substitute more expensive wood furnish, such as recycled old magazine, was successfully demonstrated in the present study. This study showed that the in-situ calcium carbonate formation process improved the optical quality of the recycled old newspaper by covering colored impurities with newly formed calcium carbonate, and improved calcium carbonate retention in papermaking process by attaching them to fibers. The strength reduction by the presence of newly formed calcium carbonate in the paper was recovered by adding strength agent. High ash retention at high ash content under the strong turbulence in the modern paper mill was achieved by the application of the in-situ calcium carbonate formation method. The quality-upgrade of recycled fibers and cost saving in the manufacture of duplex paperboard were demonstrated in the mill trial.

IntroductionHospitals in the Netherlands generate approximately 1.3 million kg of waste from the polypropylene (PP) wrapping paper (WP) used to wrap surgical instruments each year. The aim of this study was to develop a method to recycle WP waste into new medical devices.MethodsWP was recovered from Maasstad Hospital, Netherlands. The WP was melted into bars, granulated, and mixed with virgin material at different ratios and temperatures. Dog bones were injection-molded from volume (v.%) virgin, mixed (%R), and recycled (100%R) granulate, and a tensile testing machine was used to compare the material properties before and after ten disinfection cycles at the sterilization department. Then, 25 instrument openers were made from the 50%R material and circulated for four weeks.ResultsThe data indicated no significant differences in the mechanical properties at different melting temperatures. For dog bones made from the 100%R, 50%R, and virgin granulate, the Young's moduli were 1021 (SD13), 879 (SD13), and 795 (SD14) MPa, and the strains were 8%, 12%, and 14%. Ten disinfection cycles did not significantly change the material properties. After one month, the openers did not show any deterioration or damage other than surface scratches.DiscussionThe results indicated that the initial WP melting temperature did not influence the mechanical properties. Although devices could be produced directly from the recycled WP granulate, increasing the recycled granulate in the mix ratio increased the strength and brittleness.ConclusionsIt is feasible to recycle WP waste into a high-quality raw material for the injection molding of medical devices without using additives. This would allow hospitals to become more compliant with the circular economy enabling economically viable and circular processes that positively contribute to cleaner technical processes, sustainable products, and the reduction of medical waste.

Guiding industries to produce in an effective and environmentally sustainable manner has become a key issue for governments around the world. Over the past 15 years, series of regional and industrial development policies have been introduced by the Chinese government. This has influenced the geographical distribution and energy efficiency performance of China’s industries. This paper quantifies the influence of enterprises geographical distribution on energy efficiency improvement in the paper industry and aims at providing some helpful suggestions on industrial development to policy makers. The main results show that, firstly, the paper industry in eastern China shows obvious characteristic of agglomeration. The average location quotient is 1.2278. However, following the industrial and regional development policies, the characteristic of agglomeration is weakening. Secondly, only when agglomeration reaches a certain level (location quotient is above 0.5447) will industrial agglomeration positively impact on industrial energy efficiency improvement (a 1% increase in agglomeration will increase dynamic energy efficiency by at least 0.23%). Thirdly, the regional development policies carried out by the government slow the pace of energy efficiency improvement in China’s paper industry. The empirical results indicate that the government needs to consider regional characteristics and consciously guide industrial enterprises to concentrate in the dominant area.

Different heating processes were applied to pretreat the pulp and paper mill sludge to enhance the hydrolysis stage. Hot air oven, autoclave, microwave and water bath were used for comparison. Chemical analyses exposed that all the pretreatment methods have shown improvement in solubilisation of organic matter. Among the pretreatments studied, heat transfer through hot air (80 °C for 90 min) mode had the highest impact on sludge solubilisation. There was an increase in cellulose (P = 0.0096), acid soluble (P = 0.0053) and insoluble lignin (P = 0.0012), but decrease in hemicellulose (P = 0.0009) content after pretreatment. The XRD and FT-IR spectroscopic characterisation shows the development of aliphatic, unsaturated and carbonyl carbon functionalities in the pretreated samples at higher severities. FESEM picture also confirms the change in structure after pretreatment. Thus, pretreatments contribute to disruption of the lignocellulosic structure making the cellulose easily accessible to acidogenic microorganisms.

China’s paper industry consumes a lot of energy and emits huge amounts of pollutions. The Chinese government over the past decades has done a lot to promote energy efficiency of the industry. This paper studies the impact of industrial polices to improve energy efficiency. The energy efficiency change is firstly studied under a framework of total factor efficiency. On this basis, different econometric models are built to discuss the detailed energy efficiency characteristics of the paper industry. The main results are as follow: (i) ownership structure did influence the energy efficiency, but the influence is different in different conditions; (ii) energy efficiency of the paper industry can be improved by economies of scale; (iii) market competition can to some extent overcome the motivation and supervision problem that often occur in state-owned companies; (iv) energy price cannot play the role of resource allocation well in China. Finally, based on our findings, some suggestions are provided.

This work assesses six different agricultural residues with the aim of finding alternative raw materials for a soda semichemical pulping process: stems of bell and chili pepper ( Capsicum annuum ), broad bean ( Vicia faba ), asparagus ( Asparagus officinalis ), pea ( Pisum sativum ), and okra ( Abelmoschus esculentus ). Pulping yields higher than 60% (m/m) were obtained, except for pea stems (43%). The drainability of all the pulps, expressed as the Schopper-Riegler index (oSR), had values of over 70 oSR. The Kajaani analyses of the fibers showed acceptable fiber lengths in all cases (0.64–0.92 mm), but on average shorter than the lengths of pulps from a commercial fluting paper (Old corrugated Container, OCC), that was found to be 1.27 mm. Handsheets of paper were produced both with the pulps under study and with mixtures of these pulps with OCC pulp. Several properties were measured to assess the use of the new fibers in a paper for cardboard production. The property showing the greatest differences was the Gurley porosity, ranging from 25 mL/min (asparagus) to 1300 mL/min (broad bean). Of the six residues tested, the okra residue fiber showed better properties than the commercial paper fiber (Concora Medium Test indexes: 1.5 N m 2 /g and 1.1 N m 2 /g respectively, Burst Indexes: 2.3 kPa m 2 /g and 1.7 kPa m 2 /g, respectively), yielding similar mechanical properties to those of high quality fibers obtained from miscanthus ( Miscanthus giganteus ). Broad bean residue could also be a promising raw material, though its properties are not as good as okra’s.

Pulp and paper is considered to be the fourth most energy-intensive industry (EII) worldwide. However, as most of the CO2 emissions are of biomass origin, this sector has the potential to become a carbon-negative industry. This study proposes a new concept for conversion of the pulp and paper industry to carbon negative that relies on the inherent CO2 capture capability of the Kraft process. The techno-economic performance of the proposed carbon-negative system, based on calcium looping (CaL) retrofitted to a pulp and paper plant, was evaluated. The effect of CaL design specifications and cost assumptions on the thermodynamic and economic performance were evaluated. Under the initial design assumptions, the reference pulp and paper plant was shown to turn from electricity importer to electricity exporter with the cost of CO2 avoided equal to 39.0 €/tCO2. The parametric study showed that an increase in the fresh limestone make-up rate resulted in a linear increase of the specific primary energy consumption for CO2 avoided (SPECCA) and a reduction in the amount of electricity exported to the electric grid. This translates into an increase in the price of pulp and newsprint, and the cost of CO2 avoided. This study has also demonstrated that the pulp and paper industry has high potential to become carbon negative. It has been shown that carbon capture and storage would become economically viable in this industry if the negative CO2 emissions are recognised and a negative CO2 emissions credit of at least 41.8 €/tCO2 is implemented.

Paper production generates pulp and paper wastewater (PPW), and it is difficult to remove the high-level pollutants in PPW efficiently. Herein, an efficient industrial-scale pulp and paper wastewater treatment plant (PP-WWTP) that integrated physicochemical and biological processes is investigated and reported. This PP-WWTP treated 2.3 Mt of wastewater with 17,388 ± 1436 mg/L chemical oxygen demand (COD) annually. The PP-WWTP can effectively remove over 99.81% of the COD. In detail, the physical, anaerobic, aerobic and chemical steps accounted for 41.6%, 40.0%, 11.9%, and 6.5% of COD removal, respectively. The microbial communities of the bioreactors removed the pollutants efficiently and contained diverse microbes. Further metagenomic analyses of the bioreactors identified more than 90,000 genes/gene fragments encoding for carbohydrate-active enzymes (CAZys), demonstrating high lignocellulose degradation ability of the bioreactors at molecular level. The xylanase activity assay showed some lignocellulase in the bioreactors were functional. Recycling the residual heat from the PPW along with energy recovered from biological treatment of the PPW, in the form of biogas (20,000 m³/d), could generate more than 1.5 M USD benefits/y. The results of this study demonstrated that the integrated physicochemical and biological process for PPWW treatment could effectively remove pollutants while generating revenue.

To reduce energy use and achieve a low carbon production in pulp and paper industry (PPI), it is essential to improve energy efficiency in pulp and paper production. In this study, the energy savings from the PPI were estimated based on a techno-economic analysis by EAGER tool for PPI at the factory level. The structure and implement procedure were introduced initially. Two typical pulp and paper mills from China were determined to estimate the impact of selected energy efficiency technologies (EETs) on energy savings as the cases in the base year. One Factory (A) only produced paper products (i.e. corrugated paper and Kraft linerboard) while the other Factory (B) also produced market pulp besides sack paper. In totally 22 selected EETs were applied to assess their saving potential in Factory A, and 29 measures were applied in Factory B. The results show that 2290 TJ and 1179 TJ of final energy could be saved annually in Factory A and B, corresponding to reduction of 29.4% and 13.6% total energy consumption respectively for the case factories. The CO2 reduction potential was 32.3% for Factory A compared with that of 16.6% in Factory B. It suggests that the pulp and paper mills should encouraged to use this method estimating energy saving potential, and improve their energy efficiency with suggested measures in order to reduce energy consumption and related carbon emissions further in the coming years.

In recent years, the pulp and paper industry has changed a lot and products have been constructed in quite different methods using new technologies. It can be due to the emergence of challenges and constraints such as shortage of raw materials, energy consumption (fossil fuels, electric, etc.), management of the resulting pollutants, environmental issues, ongoing legal requirements and cleaner production strategies. In Iran, the pulp and paper industry's technological development is not keeping pace with global growth. Iran's pulp and paper mills supply a small fraction of domestic market. The reasons can be due to old technologies being used in factories, aging machinery, low productivity of production systems and lack of coordination with modern technologies. It leads to low-quality of paper products and willingness to buy local products. The aim of this study is to select the most appropriate technologies in the pulp section, due to high impact of pulp quality on the quality of final paper. Using a 2-filterd fuzzy decision-making, hierarchical structure of research is designed to assess technological alternatives according to the selected criteria. Findings show that after passing through two filters, Kraft method was chosen as the most appropriate method. The Kraft process has still many advantages like the high quality of the produced pulp and self-sufficiency in energy supply. This framework offers an appropriate procedure for identifying and selecting technologies that has not been used in past researches. Using this framework facilitates using a clear procedure for evaluating and selecting technology and prevents future losses for organizations.

Paper-based electronics offer a simple and cost-effective means to fabricate flexible devices. Here, we report an efficient pen-on-paper approach to construct metasurfaces on paper with silver units. Further, paper-based metasurfaces are employed to shield the electromagnetic interference which create new opportunities in turning waste paper into a solution for eliminating electromagnetic pollution. Experimental measurements and simulations show that waste paper-based metasurface manufactured in this way exhibits remarkable electromagnetic shielding properties with small thickness (thickness reduced more than 90% compared with that of traditional shielding materials), which makes it an ideal candidate for specific frequency electromagnetic filters. In addition, it can be readily extended to other regions of the electromagnetic spectrum, widened the shielding band by simply scaling the silver units' sizes and utilizing appropriate three-dimensional structures. Having taken performance into consideration, production is also taken into account. Paper-based shields offer both economic and energy benefits when considered on electronic printing, in addition, environment friendly nature and pliability of paper as well as simple fabrication procedure make paper-based metasurfaces promising candidates for the future ‘green’ electronics.

China has become the world largest paper and paperboard producer. However, pulp and paper industry has involved high resource consumption and severe pollution especially for water. This research has assessed the eco-efficiency of China's pulp and paper industry at the national level and provincial level. An overview regarding the cleaner production of China's pulp and paper industry was presented to reveal the measures for reducing environmental impact in the last two decades. Slacks-based measure was used to analyze the efficiency levels of 16 provinces' pulp and paper industries. To uncover the underlying causes of eco-efficiency performance, Malmquist–Luenberger index was calculated to discover the drivers of productivity growth of pulp and paper industries. Our results showed that the pollution treatment of China's pulp and paper industry has made progress in terms of water consumption and water pollution, although the absolute amount of pollution discharge is still large. Chemical oxygen demand emissions are still the first critical influencing factor of pulp and paper industry's inefficiency. Furthermore, efficiency progress was the dominating contribution of the industry's productivity growth between 2010 and 2013. The policies for adjusting the industrial structure of pulp and paper industry have resulted in the scale effects through eliminating backward production capacity and accelerating merger and acquisitions. Moreover, the productivity of pulp and paper industry was underestimated when the undesirable outputs were ignored. It indicates that the stricter environmental regulations have positive effects on paper companies to internalize environmental pressures in the production activities through environmental management. In the future, pulp and paper companies should further internalize the cost of pollution treatment through scale effects and technology improvement.

Sunflower stalk was evaluated as a potential fiber source to make fluting paper using neutral sulfite semi-chemical pulping process, in comparison with Mazandaran wood and paper industry mill made hardwood-based neutral sulfite semi-chemical (NSSC) pulp. Sunflower stalk consists of two distinct fractions including inner bulky pith and outer woody wall. The stalk has to be de-pithed for the purpose of papermaking because of lower cellulose, and higher ash content in pith-containing stalk. The results of pulping showed that the rate of delignification in NSSC cooking of de-pithed sunflower stalk with 20% lignin was surprisingly very low, despite of being a non-wood fiber source. However, sunflower stalk NSSC pulp showed very good response to refining and produced denser sheet due to lower digester yield and higher fiber flexibility coefficient, in comparison with Mazandaran wood and paper industry pulp sample. In addition, sunflower stalk pulp has been demonstrated to be an appropriate fiber source for making fluting paper at higher or comparable tensile-loaded strength properties such as tensile and burst, and higher compression-loaded strength properties including corrugated medium test and ring crush test.

The study investigates for the first time the possibility of using carbon rich paper recovery sludge, and nitrogen rich meat processing industry waste as cultivation medium for the production of high value enzymes needed in the respective industries. The complex cellulose rich deinking sludge was able to support the growth of many industrially relevant enzyme producing microorganisms (Bacillus licheniformis, Candida cylindracea, Aspergillus oryzae, Trichoderma reesei) and of recombinant enzyme producers (Escherichia coli and Pichia pastoris). Further detailed studies with Trichoderma reesei as model organism demonstrated that the organism was able to grow optimally in the presence of 40gL-1 paper sludge as carbon source and 67.5 gL-1 pasteurised blood as nitrogen source substituted in Mandels medium. Under these conditions cellulase activities up to 28.1 nkat FPU were achieved. Anyhow, to achieve these results pretreatment of both waste streams is inevitable. In summary, this study provides the practical basis for a valorisation systems of paper industry waste to produce valuable enzymes to be used on-site in paper processing or for other purposes.

International audience; An energy audit is a primary step toward improving energy efficiency at the facility level and ensuring a clean production. The pulp and paper sector is one of the most energy-intensive industries in Morocco. This article aimed at identifying energy conservation opportunities at a Small and Medium-sized paper industry. The audit results together with their financial viability are presented regarding the analysis of energy consumption and electrical quality issues. The paper introduces an action plan for a more efficient energy use of some specific applications such as furnaces and compressed-air installations as well. The recommended energy efficiency measures have the potential of saving about 347.85 MWh of electrical energy and 101.78 MWh of thermal energy corresponding to reductions of 11.48% and 2.22%, respectively. The total investments related to the application of the action plan is approximately 290.53 kMAD and the global payback period does not exceed one year. It was also shown that a total quantity of 283.39 t of CO2 emissions can be saved annually.

China's paper industry accounts for a larger proportion of the global paper industry and consumes large amounts of energy. Energy conservation and pollution reduction of the industry have become the focus of China's national development strategy. Energy efficiency is an important index which directly determines the amounts of energy consumption and pollution emissions. To understand the energy efficiency evolution of China's paper industry, this paper establishes an input-output data of the paper industry for 29 provinces in China and applies DEA method and econometric models to estimate and comprehensively discuss the energy efficiency issues based on the framework of total factor efficiency. Our results indicate that China's paper industry has a large energy saving potential even though its energy efficiency has improved during the period 1990–2013. The saving potential is about 65% under the meta-frontier and 44% under the group-frontier. Moreover, there are significant differences between different regions in production technology and energy efficiency. The performance of eastern China is better than other regions. But the technology gaps between the different regions are shrinking and converging over time. Finally, some policy recommendations are proposed to improve the energy efficiency of the industry.

Worldwide pulp and paper industry is recognized as a serious threat due to the discharge of various toxic contents present in its effluent to the surrounding environment. To combat this challenge, the role of oleaginous yeast to utilize the pulp and paper industry effluent for the integrated toxic contents removal and sustainable biodiesel production were undertaken. Oleaginous yeast Rhodosporidium kratochvilovae HIMPA1 was used as a model organism for its unique ability to utilize pulp and paper industry effluent as a culture medium and accumulate high quantity of triacylglycerol or neutral lipids as large size lipid droplets of 4.56 ± 0.24 μm within its cellular compartment. The maximum cell dry weight (13.87 g/L) with total lipid yield of 8.56 g/L was obtained after 144 h of cultivation. Data showed significant reduction in effluent toxic components i.e. color, 89%; lignin, 94.27%; phenol, 99.60%; biochemical oxygen demand, 77.36%; total dissolved solids, 84.59%; and chemical oxygen demand, 94.22%. Fatty acid methyl esters profile revealed high quantity of long chain monounsaturated fatty acids (45.43%) and polyunsaturated fatty acids (15.91%) that improves biodiesel quality under low temperature condition in terms of low cold filter plugging point along with good oxidative stability and cetane number as per American Society for Testing and Materials D6751-02 and European Committee for Standardization - EN14214 guidelines.

Recycling of waste paper was investigated with the aim of boosting the use of recycled materials and reducing the impact of waste paper on environment. Commercially important cyanoethyl cellulose product from waste paper was synthesized successfully through a cycle of chemical treatments. Waste paper was functionalized to cyanoethyl cellulose in an alkaline heterogeneous reaction environment with acrylonitrile under different reaction conditions with respect to degree of substitution. The variables studied were: Sodium Hydroxide and acrylonitrile concentration, reaction time and temperature for alkalization and cyanoethylation. All the cyanoethyl cellulose products were assessed for solubility, degree of polymerization and degree of crystallinity. The optimum conditions for cyanoethyl cellulose synthesis comprised of 8.34 M/anhydro glucose unit aqueous sodium hydroxide concentration, 30 °C alkalization temperature, 60 min alkalization time, 70 M/anhydro glucose unit acrylonitrile concentration, 60 min reaction time for cyanoethylation and 50 °C cyanoethylation reaction temperature. The optimized cyanoethyl cellulose product was characterized with fourier transform infrared spectroscopy, proton magnetic resonance spectroscopy, X-ray diffraction and scanning electron microscopy. This investigation helped to find the proper cleaner production approach towards sustainable environment management by synthesizing valuable cyanoethyl cellulose product and demonstrated that waste paper have the capacity to produce upgraded and high quality cyanoethyl cellulose for variety of applications.

An enzyme cocktail (xylanase-15U, pectinase-2U, α-amylase-2.5U, protease-2U and lipase- 1.8U) from Bacillus halodurans was applied for the biobleaching of unbleached and ODL (oxygen delignification) agro based pulp in the R&D set up of Shreyans Paper Mills Ludhiana, India, upscaling from 5 g (at lab scale) to 100 g odp (oven dried pulp). Enzyme pre-treatment was carried out at temperature and pH optima of 65 °C and 9–9.5 for 90 min followed by reduced chemical treatment. In case of unbleached agro pulp, as compared to the total chemical bleaching in mill, enzyme cocktail pre-treatment reduced the chemical usage by 50% without compromising brightness and rather with increased tensile strength (23.55%), burst factor (20.3%) and tear factor (3.17%) and reduced kappa number (19.5%). In case of ODL pulp, enzyme cocktail pre-treatment reduced the chemical usage by 40%, yet increasing brightness (2.24%), tensile strength (20.96%), burst factor (5.1%) and tear factor (8.2%) with reduction in kappa number (4.54%). The enzyme cocktail thus can make the paper manufacturing process greener, safer, economical and eco-friendly and may replace big budget ODL technologies.

In accordance with global estimations, approx. 15 million tons of residues are yearly generated from paper and pulp industry, which are traditionally used as biofuels or just disposed in landfills. However, residues composition and laws in force urge producers to search for new waste management strategies. From another point of view, the construction industry uses more than 33% of total natural resources, worldwide which has led several governments to limit the use of natural raw materials for building. In particular, fired brick industry produces yearly approx. 1600 billion bricks which represents millions of tons of natural resources consumption. Therefore, the goal is to contribute to reduce the amount of used clay. Thus, this paper explores the mineral and technological properties of brick made by using different percentages of paper pulp residues and fired at 900 °C. Results indicate that by increasing the replacement ratio, blend requires larger amounts of water which leads to a proportional increasing of shrinkage during drying. In spite of mineral transformations are not influenced by paper pulp residue, the porosity is linearly increased which leads to reduce compressive strength and thermal conductivity up to 30% for 20% of replacement ratio, in both cases. Thus, it is concluded that series made by replacing up to 10% show compressive strength above 5 MPa, water absorption beyond 20% and toxicity indexes meet the mandatory requirements.

Fly ash and waste lime are solid wastes generated in pulp and paper mills. Due to high CaO contents, these secondary lime materials can be potentially utilized in the steelmaking process to partially replace primary lime. In this study, fly ash and waste lime from Swedish pulp and paper mills were made into briquettes and for the first time utilized as slag formers to replace primary lime in a pilot-scale Argon Oxygen Decarburization (AOD) stainless steelmaking process. The purpose was to evaluate how these CaO-containing materials could affect the AOD process and the steel quality. The results show that the S, P and CaO contents in the fly ash and waste lime are important concerns for metallurgical application. Firstly, due to lower CaO contents (61.5% CaO in fly ash and 90.6% CaO in waste lime versus 95.2% CaO in primary lime), utilization of these secondary lime materials could lead to higher slag amounts in the AOD converter. Secondly, due to higher S and P contents (0.40% S and 0.26% P2O5 in fly ash, 0.11% S and 0.75% P2O5 in waste lime versus 0.08% S and 0.01% P2O5 in primary lime), utilization of these secondary lime materials could increase the S and P contents in the steel. The S content in the steel can be controlled during the reduction and desulfurization stages; however, the P content in the steel increases with an increased use of these secondary lime materials. Thirdly, the metallurgical performance of fly ash and waste lime is as good as primary lime when considering the aspects that: (a) utilization of fly ash and waste lime doesn’t have negative effects on the decarburization stage nor on the reduction stage during the AOD process; and (b) fly ash and waste lime are as efficient desulfurization agents as primary lime. In future industrial applications, the alkali content and the variations of chemical compositions (especially with respect to S, P and CaO) of these secondary lime materials need to be carefully controlled to ensure a sound metallurgical operation.

Each day a large amount of toilet paper (TP) is flushed into sewers. Recovering the disintegrated fibers from wastewater can reduce the treatment cost and the recovered fibers have some value-added applications. However, typical preliminary treatment units are inefficient at capturing these small-sized fibers. Although sieving can recover them effectively, it is rarely used due to high costs. Results from this study suggested that redesigning TP to disintegrate less in water can be a more cost-effective approach. Here, we evaluated the disintegration of TP in sewers and fiber recovery through screening, sieving, and sedimentation. We found that the highly disintegrated TP are significantly more challenging to retrieve using conventional approaches. Fine screens with an opening size of 3 mm recovered only 45.7% of the TP fibers. Sieves with 0.1–1 mm openings retrieved up to 94.5% of the TP fibers but were very prone to clogging. Further, the fiber recovery by preliminary treatment was heavily impacted by the TP disintegration degree, which was found to be predominantly affected by the flow motion, wetting time, and inherent stability of TP. A life-cycle cost (LCC) analysis showed that redesigning TP (i.e., designing it to disintegrate into fragments rather than separated fibers) could significantly promote fiber recovery with the existing infrastructures. The 15-y operational costs could be reduced by up to 46% by using redesigned TP. This work presents a promising way to facilitate TP fiber recovery from wastewater at lower cost; pilot and full-scale surveys must be conducted to evaluate feasibility.