Search

Fluoro-functionalized paper was prepared and applied in solid phase extraction (SPE) for the analysis of trace-level perfluorinated compounds (PFCs). The proposed fluoro-functionalized paper-based solid-phase extraction (Fp-SPE) exhibits significant advantages for sample preparation, such as the biodegradability of paper-based adsorbent, simple manipulation and low cost. Owing to the fluorous affinity, the Fp-SPE technique with high sensitivity and high selectivity is more suitable for the selective enrichment of fluorine-containing molecules from the background of non-fluorinated organic compounds in a real water sample. Combined with high-performance liquid chromatography coupled with electrospray ionization-tandem mass spectrometry analysis (HPLC-MS/MS), the linear range of the PFCs, including perfluorobutyric acid (PFBA), perfluorooctanic acid (PFOA), perfluorooctane sulfonic acid (PFOS), and perfluorodecanoic acid (PFDA), was 0.20–5.0 ng/L with the limits of detection (LOD) ranging from 0.04–0.05 ng/L and the limits of quantification (LOQ) ranging from 0.15-0.20 ng/L. The method was then applied to the analysis of tap water, river water and waste water samples. The results of the actual sample analysis are consistent with that by reverse phase SPE (RP-SPE).

The adsorption of hydrocarbons present in gasoline residues on household materials was investigated via inverse gas chromatography (IGC). A series of hydrocarbons (n-heptane, n-octane, n-nonane, toluene, p-xylene, and 1,2,4-trimethylbenzene) and three household materials (carpet fibers, cotton fabric, and cardboard) were selected in this work. IGC measurements using columns packed with these household materials were conducted to obtain molar enthalpies of adsorption of the selected hydrocarbons over the temperature range of 40 to 70 °C. Adsorption isotherms and Henry’s law solubility coefficients (S) were also determined at 40 °C. Results from our IGC measurements revealed that molar enthalpies of adsorption, adsorption isotherms, and solubility coefficients were largely dependent upon the structures and size of hydrocarbons and the choice of solid substrates. Measured molar enthalpies of adsorption became more exothermic with increasing size of hydrocarbons, ranging from −23.4 to −40.9 kJ/mol for carpet fibers, −36.2 to −48.2 kJ/mol for cotton fabric, and −30.1 to −52.5 kJ/mol for cardboard. From the adsorption isotherms and the measured retention times as a function of the injection amount, the adsorption affinity of hydrocarbons to the carpet fibers was found to be weaker than the affinity between hydrocarbon molecules, producing relatively lower solubility coefficients for all hydrocarbons than those measured on cotton fabric and cardboard. However, the adsorption affinities of hydrocarbons to both cotton fabric and cardboard were much stronger with increased solubility coefficients presumably due to the diffusion and dispersion of hydrocarbons through solid substrates. In particular, solubility coefficients of three aromatics on cardboard were significantly larger than those measured on carpet fibers and cotton fabric. This might be responsible for previously reported enhanced persistence of gasoline residues spiked on cardboard.

An extraction and determination method is shown for the analysis of dyes and solvents present in two types of ballpoint pen inks that are deposited onto paper. Ink extracts are analysed using a combination of gas chromatography with mass spectrometry (GC-MS), and high-pressure liquid chromatography with photodiode array detection (HPLC-DAD), within a single sample extraction procedure. Seventeen solvents and thirteen dyes contained in two Montblanc® inks (black and blue) were monitored for 45 months at monthly intervals, in order to determine variations in the concentrations of the compounds over time. We also studied the relative variations between different compounds and the generation of degradation products such as phenol. The concentration data obtained from these compounds during their exposure have been analysed and a multiple regression model is developed for each ink type that allows an estimate of the exposure time of the ink on paper with a maximum error of between 4 and 7 months.

A sensitive, rapid and efficient ionic liquid-based vortex assisted liquid-liquid microextraction (IL-VALLME) with Liquid Chromatography Mass spectrometry (LC-MS/MS) method is proposed for the determination of bisphenols in thermal paper. Extraction factors were systematically optimized by response surface methodology. Experimental factors showing significant effects on the analytical responses were evaluated using design of experiment. The limit of detection for Bisphenol-A (BPA) and Bisphenol-S (BPS) in thermal paper were 1.25 and 0.93μgkg-1 respectively. The dynamic linearity range for BPA was between 4 and 100μgkg-1 and the determination of coefficient (R2) was 0.996. The values of the same parameters were 3-100μgkg-1 and 0.998 for BPS. The extraction recoveries of BPA and BPS in thermal paper were 101% and 99%. Percent relative standard deviation (% RSD) for matrix effect and matrix match effects were not more than 10%, for both bisphenols. The proposed method uses a statistical approach for the analysis of bisphenols in environmental samples, and is easy, rapid, requires minimum organic solvents and efficient.

This manuscript describes the development of a capillary electrophoresis (CE) method for the detection of acid and basic dyes and its application to real samples, blue-pen-ink strokes on office paper. First, a capillary zone electrophoresis (CZE) method was developed for the separation of basic and acid dyes, by studying the separation medium (buffer nature, pH and relative amount of additive) and instrumental parameters (temperature, voltage and capillary dimensions). The method performance was evaluated in terms of selectivity, resolution (above 5 and 2 for acid dyes and basic dyes, respectively, except for two basic dye standards), LOD (lower than 0.4 mg/L) and precision as intraday and interday RSD values of peak migration times (lower than 0.6%). The developed method was then applied to 34 blue pens from different technologies (rollerball, ballpoint, markers) and with different ink composition (gel, water-based, oil-based). A microdestructive sample treatment using a scalpel to scratch 0.3 mg of ink stroke was performed. The entire electropherogram profile allowed the visual discrimination between different types of ink and brands, being not necessary a statistical treatment. A 100% of discrimination was achieved between pen technologies, brands, and models, although non-reproducible zones in the electropherograms were found for blue gel pen samples. The two different batches of blue oil-based pens were also differentiated. Thus, this method provides a simple, microdestructive, and rapid analysis of different blue pen technologies which may complement the current analysis of questioned documents performed by forensic laboratories.

This study reports on a rapid method for the determination of methanol in paper-based materials by alkaline extraction, coupled with headspace analysis. Methanol partition equilibria between solid–liquid phases and vapor–liquid phases were conducted in two separate containers, from which an equation for calculating the total methanol content in the original paper sample was derived. It was found that the extraction equilibrium of methanol from solid sample could be achieved within 5 min at room temperature using a high-speed disintegrator, and a subsequent neutralization step is an effective way to prevent methanol from being regenerated at high temperature during headspace equilibration. The results showed that the relative standard deviations for reproducibility tests were in the range of 1.86–6.03%, and the recoveries were in the range of 92.3–107%. The present method is simple and practical; it can be an efficient tool for quantifying the methanol content in paper-based materials and thus play an important role in the investigation of methanol migration behavior in food and beverage packaging.

In this paper, chemically modified cellulose paper was introduced as a novel extracting phase for thin film microextraction (TFME). Different reagents (Octadecyltrichlorosilane, diphenyldichlorosilane, cyclohexyl isocyanate and phenyl isocyanate) were used to modify the cellulose papers. The modified papers were evaluated as a sorbent for the extraction of some synthetic and natural estrogenic hormones (17α-ethynylestradiol, estriol and estradiol) from aqueous samples. Liquid chromatography–fluorescence detection was used for the quantification of the extracted compounds. The cellulose paper modified with phenyl isocyanate showed the best affinity to the target compounds. TEME parameters such as desorption condition, shaking rate, sample ionic strength and extraction time were investigated and optimized. Limit of detections were between 0.05 and 0.23 μg L −1 and relative standard deviations were less than 11.1% under the optimized condition. The calibration curves were obtained in the range of 0.2–100 μg L −1 with a good linearity ( r 2 > 0.9935). Wastewater, human urine, pool and river water samples were studied as real samples for the evaluation of the method. Relative recoveries were found to be between 75% and 101%.

So far the majority of the measurements of mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH) were obtained from on-line high performance liquid chromatography-gas chromatography-flame ionization detection (on-line HPLC-GC-FID). Since this technique is not available in many laboratories, an alternative method with more easily available tools has been developed. Preseparation on a small conventional liquid chromatographic column was optimized to achieve robust separation between the MOSH and the MOAH, but also to keep out the wax esters from the MOAH fraction. This was achieved by mixing a small portion of silica gel with silver nitrate into highly activated silica gel and by adding toluene into the eluent for the MOAH. Toluene was also added to the MOSH fraction to facilitate reconcentration and to serve as a keeper preventing loss of volatiles during solvent evaporation. A 50 μl volume was injected on-column into GC-FID to achieve a detection limit for MOSH and MOAH below 1 mg/kg in most foods.

We developed a convenient method by coupling frontal elution paper chromatography with desorption corona beam ionization mass spectrometry (DCBI-MS) for rapid determination of chlorphenamine added in herbal medicines or dietary supplements. In this method, the ethanol extract of the herbal products was spotted directly onto an isosceles triangular filter paper sheet, and then the paper sheet was developed under strong elution condition with the sample zone migrating at the solvent front. The analyte was finally condensed at the V-shaped tip which could then be placed under the visible plasma beam of DCBI for ionization. The overall procedure took less than 5 min. The frontal elution paper chromatography on a triangular plate used in this work improved the signal intensity of chlorphenamine by 30-fold due to the analyte condensing at the tip and the reduction of the background suppression. Furthermore, the paper sheet also functioned as a filter in the analysis of solid or powder samples, which can increase the analytical throughput by omitting the step of centrifugation. The proposed method in current study was successfully applied in the determination of chlorphenamine in herbal medicines. Chlorphenamine was detected in four of the twelve types of herbal medicines examined in this study. The limit of detection was 200 ng/mL (2.0 ng absolute) in full-scan positive-ion mode and the linear range was from 5.0 μg/mL to 50 μg/mL with satisfactory linear coefficient (R(2) (the square of the correlation coefficient)=0.895). Good reproducibility was achieved with relative standard deviations (RSDs) less than 15.0% and the recoveries of chlorphenamine ranged from 84.3 to 90.6%.

The paper deals with the application of size exclusion chromatography (SEC) for the studies of paper degradation phenomena. The goal is to solve some of the technical problems connected with the calibration of multi-detector SEC system and to find the correlation between SEC and viscometric results of degree of polymerization of cellulose. The results gathered for the paper samples degraded by acidic air pollutant (NO(2)) are used as an example of SEC-MALLS application. From the correlation between intrinsic viscosities and absolute value of molecular masses obtained with SEC/MALLS (Multi Angle Laser Light Scattering) technique, Mark-Houwink coefficients for cellulose in cupri-ethylenediamine solution were determined. Thus obtained coefficients were used for the determination of viscometric degree of polymerization (molecular mass) of the aged samples. An excellent correlation was found between the chromatographic values of molecular masses obtained with SEC-UV/VIS detection and the viscometric ones utilizing the improved values of Mark-Houwink coefficients.

An innovative green column-switching high-performance liquid chromatographic (HPLC) technique was developed by coupling traditional and Pb(2+) ion-exclusion columns to study enzyme hydrolysis components of waste cellulosic biomass. Pure water was used as the mobile phase to separate neutral polar analytes in high salt content solution. The column-switching HPLC-RI was connected on-line to the immobilized enzyme reactor for successive on-line desalting and simultaneous analysis of six carbohydrates (cellobiose, glucose, xylose, galactose, mannose, and arabinose) in the hydrolysate of waste paper and waste tree branch by incorporating the heart-cut and the elution-time-difference techniques. Six internal standard calibration curves in the linear concentration range of 0-2,000 microg mL(-1) were prepared. Xylitol was used as the internal standard to give excellent linear correlation coefficients (0.9984-0.9999). The limits of detection and quantification for cellobiose, glucose, xylose, galactose, mannose, and arabinose varied between 0.12-4.88 and 0.40-16.3 microg mL(-1), respectively, with an accuracy of 90-102% and a precision of 0.1-7.8%. Cellulose and hemicellulose contents were higher in waste paper than in waste tree branch.

The determination of perfluorooctanoate (PFO) in articles of commerce has become increasingly important to understand if treated products are a possible source of PFO. An LC–MS/MS method for the determination of PFO in paper and textile using a dual labeled 13C-PFOA internal standard was successfully developed and validated. Residues of PFO were determined using an isocratic, reversed-phase high-performance liquid chromatography (HPLC) method with an ammonium acetate/methanol buffer. Ions monitored were 413 (parent) and 369 (daughter) for PFO and 415 (parent) and 370 (daughter) for dual labeled 13C-PFOA internal standard. As a precaution against ubiquitous PFO that occasionally occurs in mobile phase or instrument components, two Hypercarb™ cartridges (4 mm) were placed before the HPLC injector. Any PFO that was captured by the cartridges was removed before each injection by flushing the system with 100% methanol prior to equilibration with the isocratic mobile phase. Overall recovery and standard deviation over a 3 day validation regimen for samples (n = 54–55) fortified with PFOA at 5, 50, and 200 ng g−1 were 114 ± 4.9% for textile and 110 ± 7.6% for paper. The results also established a limit of detection (LOD) of 1 ng g−1 in textile and 2 ng g−1 in paper based upon S/N of the 5.0 ng g−1 fortification versus the untreated paper and textile.

A solid-phase microextraction (SPME) method has been developed for the determination of pentachlorophenol (PCP) in paper and board samples. The analytical procedure involves direct extraction of PCP from paper and board samples and determination by gas chromatography with electron capture detection (GC-ECD). Two kinds of commercially available fibres; 100 microm polydimethylsiloxane (PDMS), apolar, and 85 microm polyacrylate (PA), quite polar, were evaluated to determine the extraction efficiency of pentachlorophenol. Parameters affecting the extraction process, such as temperature and time, were studied. Moreover, time of desorption and the effect of addition of salt were also investigated. The optimized procedure was applied to the analysis of pentachlorophenol (PCP) in five samples of virgin and recycled paper and board. The PCP content was determined by GC-ECD. To evaluate the effectiveness of the proposed method, it was compared with conventional extraction method with liquid-liquid extraction and derivatization. Detection limit of 0.015 microg/g for PCP in paper was achieved with a RSD of 14%.

Two low-volume solvent continuous extraction methods are applied to the extraction of paper matrices. In the methods reported here, a complex mixture of fluorescent whitening agents (FWAs) and azo dyes (AZOs) used in paper materials intended to come into contact with foodstuffs was extracted by using subcritical water extraction (SWE) and dynamic sonication-assisted solvent extraction (DSASE). Rationale for the work is based upon migration concerns of these groups of analytes from the packaging to the packaged items, thus compromising their subjective and/or objective quality. In SWE, sample was extracted in 21 min with 0.5 mL of water, whereas the DSASE method required 11 min and used 7 mL of water. DSASE was further developed by incorporating an organic modifier in order to change water polarity, thus improving extraction of moderately polar analytes. This way, modified-DSASE used a total organic volume of 0.9 mL which represents a reduction of 200 times in organic solvent consumption (200 mL versus approximately 1.0 mL) and 11 times in extraction time (2 h versus 11 min) compared to the existing methods. SWE was able to extract only 9 out of 12 test analytes with average recoveries between 10 and 25% whereas modified-DSASE succeed in extracting all the target analytes with an average recovery of 89%. Complete discussion and explanation concerning these differences are provided in the text.

The surface energies of various inorganic fillers including kaolin clay, titanium dioxide, and talc were examined using inverse gas chromatography (IGC). In an earlier investigation that examined calcium carbonate fillers, dehydration by heating under a dry nitrogen purge had a substantial influence on the apolar (gammaS(LW)) and polar (gammaS(AB)) components of surface energy as measured using IGC. Using the same approach, the influence of such conditioning on several inorganic fillers used in papermaking were determined using preconditioning IGC from 100 to 300 degrees C, and sequential isothermal analysis at 100 degrees C. Results from IGC analysis of titanium dioxides (rutile and anatase) were similar to precipitated calcium carbonate (PCC) for temperatures up to 200 degrees C. PCC was significantly more energetic after preconditioning at 300 degrees C, which may indicate the onset of significant thermal decomposition that titanium dioxides will not exhibit. Kaolin clay samples had relatively high apolar surface energy similar to that of the chalk samples. Calcination gave lower gammaS(LW) values that could not be accounted for by changes in the microporous structure. More likely the differences resulted from contamination of highly energetic surface sites with adsorbates other than water. Talc samples exhibited relatively high apolar surface energies that increased with preconditioning temperature. The results provided insight into the significance of water on the final adhesion properties of fillers in the sheet structure or coating layer.

Paper fiber was treated in a heterogeneous esterification reaction with four different fatty acids. This fiber was used to strengthen polyethylene (PE) composites. Modified and unmodified cellulose fiber was characterized with inverse gas chromatography. In previous work, characterization was also carried with X-ray photoelectron spectroscopy (XPS), solid-state NMR, differential scanning calorimetry and thermogravimetry. Individual fibers were found to be covered with the corresponding esters (cellulose undecylenate, undecanoate, oleate, stearate) with partial degrees of substitution of the cellulose. Comparison of XPS and NMR results showed that the surface degree of substitution of the cellulose fiber was higher than for the bulk, showing that the esterification reaction was a surface phenomenon. The aim of this work was to acquire information on the surface characteristics of the fiber and to see whether it could be correlated to PE composite mechanical strength results. The conclusions are that polar probes seem to diffuse more into the fibers than the non-polar probes, as the non-polar component of the surface tension of the modified fiber is much lowered towards that of PE, while donor–acceptor characteristics are hardly changed by esterification. The ester with the lowest non-polar component of the surface energy, the oleate, also gives the composite with the best mechanical properties.

Selected organic compounds commonly occurring in plant and animal tissues have been chromatographed on glass fiber, paraffin-coated and untreated cellulose paper in a number of different solvent systems. The RF values of these compounds represent new additions to the literature in the solvent systems studied.

A wide range of Δ 4 - and Δ 1 , 4 -3-ketosteroids, from weakly polar to strongly polar, may be chromatographed and detected on cellulose triaacetate paper, with benzene—methanol—water mixtures as developing solvents. Three systems have been worked out. In the first a one-phase mixture of benzene, methanol and water is used as the mobile phase and the paper is not accommodated. A “reversed phase” type of chromatogram is obtained, i.e. the more polar compounds have higher R F values than the less polar ones, as is usual for chromatography on acetylated paper. If, howerver, two-phase mixtures of benzene, methanol and water are used, as was the case in the other two methods, “reversed phases”, as well as “convetional” type chomatograms may be obtained. This depeds upon whether the lower or the upper layer is used as the mobile phase, the other layer being used for accommodation of the paper. Perhaps the first-mentioned method should, in contrast to the other two, be regarded as adsorption chromatography, rather than as partition chromatography. Well-reproducible R F values are obtained and, especially with the two-phase mixtures, compact spots are found. Detection methods and R F dta are given for various Δ 4 - and Δ 1 , 4 -3- ketosteroids, ranging from C 18 to C 27 compounds and including sex hormones and adrenoccortical hormones.