Search

Abstract: High-purity carbon monoxide (CO) gas as a certified reference material (CRM) was analyzed using a micro gas chromatograph (micro-GC) with a micro thermal conductivity detector. The main reason to select the micro-GC was its compact size to provide a safe experimental environment. Thus, both the CO gas cylinder and the micro-GC were placed inside a draft shield with a limited small space. Peaks of several impurities were found in chromatograms of the micro-GC. The main impurities in the CO gas were helium, hydrogen, oxygen, nitrogen and carbon dioxide. It was found that helium was the impurity of the highest concentration. High-accuracy calibration gas mixtures were used to construct calibration lines for the micro-GC. The mixtures were precisely prepared by the gravimetric blending method. Calibration lines had enough linearity and accuracy for quantitative analyses of the impurities. The values of detection limit of the impurities were 0.7–4μmol/mol. The purity of the high-purity CO gas was around 99.996%, which was the value estimated from the sum of the concentrations of the impurities. [Copyright &y& Elsevier]

Abstract: A simple method for establishing calibration curves with sorbent-filled thermal desorption tubes has been demonstrated for nitroaromatic and nitramine vapor samples using a thermal desorption system with a cooled inlet system (TDS–CIS), which was coupled to a gas chromatograph (GC) with an electron capture detector (ECD). The method relies upon the direct liquid deposition of standard solutions onto the glass frit at the head of sorbent-filled thermal desorption tubes. Linear calibration results and ideal system conditions for the TDS–CIS–GC–ECD were established for mixtures containing both cyclotrimethylenetrinitramine, a.k.a. RDX, and 2,4,6-trinitrotoluene (TNT). Because of the chemical characteristics of RDX, a higher TDS–CIS flow rate relative to the optimized approach for TNT was required for efficient RDX desorption. Simultaneous quantitation of TNT and RDX using the direct liquid deposition method with optimized instrumentation parameters for RDX were compared to results from a standard split/splitless GC inlet and a CIS. [Copyright &y& Elsevier]

Abstract: We performed a comprehensive study to assess the fit for purpose of four chromatographic conditions for the determination of six groups of marine lipophilic toxins (okadaic acid and dinophysistoxins, pectenotoxins, azaspiracids, yessotoxins, gymnodimine and spirolides) by LC–MS/MS to select the most suitable conditions as stated by the European Union Reference Laboratory for Marine Biotoxins (EURLMB). For every case, the elution gradient has been optimized to achieve a total run-time cycle of 12min. We performed a single-laboratory validation for the analysis of three relevant matrices for the seafood aquaculture industry (mussels, pacific oysters and clams), and for sea urchins for which no data about lipophilic toxins have been reported before. Moreover, we have compared the method performance under alkaline conditions using two quantification strategies: the external standard calibration (EXS) and the matrix-matched standard calibration (MMS). Alkaline conditions were the only scenario that allowed detection windows with polarity switching in a 3200 QTrap mass spectrometer, thus the analysis of all toxins can be accomplished in a single run, increasing sample throughput. The limits of quantification under alkaline conditions met the validation requirements established by the EURLMB for all toxins and matrices, while the remaining conditions failed in some cases. The accuracy of the method and the matrix effects where generally dependent on the mobile phases and the seafood species. The MMS had a moderate positive impact on method accuracy for crude extracts, but it showed poor trueness for seafood species other than mussels when analyzing hydrolyzed extracts. Alkaline conditions with EXS and recovery correction for OA were selected as the most proper conditions in the context of our laboratory. This comparative study can help other laboratories to choose the best conditions for the implementation of LC–MS/MS according to their own necessities. [Copyright &y& Elsevier]

Abstract: A method is described for characterization of sulfur compounds in unaged and aged whisky. The method is based on full evaporation dynamic headspace (FEDHS) of 100μL of whisky samples followed by selectable one-dimensional (1D) or two-dimensional (2D) retention-time-locked (RTL) gas chromatography (GC)–mass spectrometry (MS) with simultaneous element-specific detection using a sulfur chemiluminescence detector (SCD) and a nitrogen chemiluminescence detector (NCD). Sequential heart-cuts of the 16 sulfur fractions were used to identify each individual sulfur compound in the unaged whisky. Twenty sulfur compounds were positively identified by a MS library search, linear retention indices (LRI), and formula identification using MS calibration software. Additionally eight formulas were also identified for unknown sulfur compounds. Simultaneous heart-cuts of the 16 sulfur fractions were used to produce the 2D RTL GC-SCD chromatograms for principal component analysis. PCA of the 2D RTL GC-SCD data clearly demonstrated the difference between unaged and aged whisky, as well as two different whisky samples. Fourteen sulfur compounds could be characterized as key sulfur compounds responsible for the changes in the aging step and/or the difference between two kinds of whisky samples. The determined values of the key sulfur compounds were in the range of 0.3–210ngmL−1 (RSD: 0.37–12%, n =3). [Copyright &y& Elsevier]

Abstract: Gas and liquid chromatography (GC and LC) coupled to mass spectrometry (MS) serve as the most powerful analytical tools commonly used to monitor pesticide residues in food, among other applications. However, both GC–MS and LC–MS are susceptible to matrix effects which can adversely affect quantification depending on the analyte, matrix, sample preparation, instrumentation, and operating conditions. Among the approaches that reduce matrix effects, the most common in pesticide residue applications is matrix-matched calibration because it is relatively inexpensive and simple. Also, it has been shown to work well during method validation when fortified samples are exactly matched with samples used for calibration. However, the quality of matrix-matched results in real-world analyses depends on the consistency of matrix effects among diverse samples. In this study, the variability of matrix effects was measured for 38 representative pesticides in 20 samples each (including different varieties) of rice, orange, apple, and spinach extracted using the “quick, easy, cheap, effective, rugged, and safe” (QuEChERS) method for analysis by LC–MS/MS and low-pressure GC–MS. Using LC–MS/MS, only oranges gave >20% matrix effects for a few pesticides. GC–MS exhibited larger matrix effects, but as in LC–MS/MS, the differences were reasonably consistent among the 20 samples tested. Main conclusions of this study are that for the conditions utilized: (1) matrix-matching was not needed for most pesticides in the simpler food matrices; and (2) for the more complex orange matrix, acceptably accurate quantitative results were achieved by using matrix-matching even with a different sample of the same type. However, full confidence cannot be extended to matrix-matched results, and for consequential applications such as regulatory enforcement, confirmatory analyses using alternate quantitative determinations should also be conducted. [Copyright &y& Elsevier]

Abstract: A protocol for the analysis of multiple prostaglandins and leukotrienes in cell culture media by using multiple internal standards was validated. A two-factor Doehlert design was used to determine the behaviour of the relationship analyte/internal standard (namely: PGE2/PGE2-d 4, PGE3/PGE2-d 4, LTB4/LTB4-d 4 and LTB5/LTB4-d 4) and to select the optimal amounts of deuterated internal standards for quantifying simultaneously the prostaglandins and leukotrienes in cell culture media by LC–MS/MS. The selection of optimal amounts of internal standards was based on mathematical models that allow visualizing concentration regions where the response factors remain constant over a wide range of analytical concentrations. The linearity of the calibration curves for each analyte at the optimal levels suggested by the mathematical models was statistically confirmed by means of the ratio lack-of-fit to pure error. The validated protocol was successfully applied in the simultaneous quantification of pro- and anti-inflammatory eicosanoids in stimulated cod head kidney cell culture media. The two-factor Doehlert design has permitted to estimate the experimental response as a function of six variables (PGE2, PGE3, LTB4, LTB5, PGE2-d 4 and LTB4-d 4) which represents a substantial reduction of resources, time and experiments of approximately 84% (7×3 experiments) when compared with the full six-factor Doehlert design (43×3 experiments). [Copyright &y& Elsevier]

Abstract: Infrared detection has been shown to be very appropriate for high temperature analysis of polyolefins. After some early reports in which dispersive or single-band filter-based detectors were applied, Fourier transform detectors have been described for this application, in order to improve the method sensitivity. Modern simple filter-based detectors prove, however, comparable sensitivity while providing a number of practical advantages when coupled to chromatographic systems: reduced cell volume, simplified hardware, continuous generation of absorbance chromatograms, as well as simpler data collection and processing. A practical method for calibration, using multiple-band signals obtained with filter-based detectors and a small number of reference materials, is here discussed. Calibration data are used to compare the performance of detectors based on different opto-electronic technologies and filter designs. A procedure for estimation of errors in the slice-by-slice measured methyl frequency, based on signal-to-noise ratio considerations, is described. The good accuracy provided by the filter-based IR detectors was noticeable, considering that it was obtained using a small set of reference materials. A minimal concentration of 0.009mg/mL was estimated to be required at the detector cell, in order to keep the errors below one unit of methyl per one thousand total carbons. This low minimal concentration requirement allows using standard SEC conditions, without compromising the molar mass distribution accuracy and resolution. [Copyright &y& Elsevier]

Abstract: Size exclusion chromatography (SEC) is often applied for characterization of protein–polyethylene glycol (PEG) conjugates regarding the number of attached PEG chains (PEGamers). SEC analysis is advantageous as it is precise, robust, and straightforward to establish. However, most SEC based assays have a maximal throughput of a few samples per hour. We present a strategy to increase analytical throughput based on combining a short column with a fast flow rate, and finally multivariate calibration in order to compensate for the resolution lost in the trade off for speed. Different multivariate approaches were compared and multilinear regression was shown to result in the most precise calibrations. Further, a dynamic calibration approach was developed in order to account for changes in column performance over time. In this way, it was possible to establish a highly precise assay for protein PEGamer quantification with a throughput of 30 samples per hour. [Copyright &y& Elsevier]

Abstract: Various analytical technologies have been developed for quantitative determination of marker compounds in herbal medicines (HMs). One important issue is matrix effects that must be addressed in method validation for different detections. Unlike biological fluids, blank matrix samples for calibration are usually unavailable for HMs. In this work, practical approaches for minimizing matrix effects in HMs analysis were proposed. The matrix effects in quantitative analysis of five saponins from Panax notoginseng were assessed using high-performance liquid chromatography (HPLC). Matrix components were found to interfere with the ionization of target analytes when mass spectrometry (MS) detection were employed. To compensate the matrix signal suppression/enhancement, two matrix-matched methods, standard addition method with the target-knockout extract and standard superposition method with a HM extract were developed and tested in this work. The results showed that the standard superposition method is simple and practical for overcoming matrix effects for quantitative analysis of HMs. Moreover, the interference components were observed to interfere with light scattering of target analytes when evaporative light scattering detection (ELSD) was utilized for quantitative analysis of HMs but was not indicated when Ultraviolet detection (UV) were employed. Thus, the issue of interference effects should be addressed and minimized for quantitative HPLC–ELSD and HPLC–MS methodologies for quality control of HMs. [Copyright &y& Elsevier]

Abstract: Direct determination of hydrodynamic radius from retention time is an advantage of the field-flow fractionation techniques. However, this is not always completely straight forward since non-idealities exist and assumptions have been made in deriving the retention equations. In this study we investigate the effect on accuracy from two factors: (1) level of sophistication of the equations used to determine channel height from a calibration experiment and (2) the influence of secondary relaxation on the accuracy of hydrodynamic radius determination. A new improved technique for estimating the channel height from calibration experiments is suggested. It is concluded that severe systematic error can arise if the most common channel height equations are used and an alternative more rigorous approach is described. For secondary relaxation it is concluded that this effect increases with the cross-flow decay rate. The secondary relaxation effect is quantified for different conditions. This is part one of two. In the second part the determination of hydrodynamic radius are evaluated experimentally under similar conditions. [Copyright &y& Elsevier]

Abstract: The uptake kinetics of 27 emerging pollutants on the polar C18 Chemcatcher have been investigated. This investigation determined the sampling rates of 20 compounds, including 16 endocrine disruptors and 4 pharmaceuticals, which were used as overall pollution indicators. Calibrations were completed in a 50-L flow-through microcosm with continuous renewal of tap water spiked with approximately 3μg/L of each pollutant and with sampling times at 1, 3, 6 and 12h and 1, 3, 7, 14, 21 and 28 days. Exponential regressions for the accumulation kinetics were plotted to confirm the maximum linear uptake times for each molecule using the half time of equilibrium (t 1/2) criteria. Of the compounds tested, 17 were accumulated linearly for up to 14 or 21 days with an R 2 above 0.98 for linear correlations. The evaluation of the release kinetics of a C18 Chemcatcher spiked with 20 deuterated compounds identified 3 potential performance reference compounds (PRCs) with exponential desorption rates showing relatively good isotropic exchange. [Copyright &y& Elsevier]

Abstract: Polycyclic aromatic sulfur heterocyclics (PASHs) consist mainly of thiophene class compounds, and are the most important organosulfur compounds in crude oils and sediment extracts. Dibenzothiophene (DBT) and its methylated homologues were identified on mass chromatograms by comparison with retention indices published in the literature. Some isomers of dimethyldibenzothiophene and trimethyldibenzothiophene that were tentatively identified in previous reports have been determined here by comparison with calculated retention indices and taking the substitution pattern of the methyl groups into account. The response factors relating that of dibenzothiophene to internal standards were obtained by GC–MS analyses of mixture solutions with different concentration ratios. We concluded that DBT-d8 (octadeutero-dibenzothiophene) is the optimal internal standard for quantitative analyses of the thiophene compound class in oils, coal, and sediment extracts. Calibration experiments for each class of compounds are absolutely necessary when quantifying polycyclic aromatic hydrocarbons and other heterocyclics with a stable isotope labeled internal standard. [Copyright &y& Elsevier]

Abstract: This contribution discusses the difference in chromatographic performance when switching from the customary employed constant flow rate gradient elution mode to the recently re-introduced constant pressure gradient elution mode. In this mode, the inlet pressure is maintained at a set value even when the mobile phase viscosity becomes lower than the maximum mobile phase viscosity encountered during the gradient program. This leads to a higher average flow rate compared to the constant flow rate mode and results in a shorter analysis time. When both modes carry out the same mobile phase gradient program in volumetric units, normally identical selectivities are obtained. However, small deviations in selectivity are found due to the differences in pressure and viscous heating effects. These selectivity differences are of the same type as those observed when switching from HPLC to UHPLC and are inevitable when speeding up the analysis by applying a higher pressure. It was also found that, when using concentration-sensitive detectors, the constant pressure elution mode leads to identical peak areas as the constant flow rate mode. Also the linearity is maintained. In addition, the repeatability of the peak area and retention time remains the same when switching between both elution modes. [Copyright &y& Elsevier]

Abstract: The aim of this research was to compare the extraction efficiencies of two modes of three-phase hollow fiber microextraction (HF-LLLME) based on aqueous and organic acceptor phases for analysis of tricyclic antidepressant (TCA) drugs. High-performance liquid chromatography with photodiode array detection (HPLC-DAD) was applied for determination of the drugs. In order to examine the ability of the new concept of HF-LLLME based on organic acceptor solvent in comparison with aqueous acceptor phase to extract the analytes, four TCAs were selected. The effect of different extraction conditions (i.e., type of acceptor phase, hollow fiber length, ionic strength, stirring rate, and extraction time) on the extraction efficiency of the TCAs was investigated and optimized using central composite design (CCD) as a powerful tool. Both methods were characterized by good linearity and high repeatability, but HF-LLLME with organic acceptor provided higher extraction efficiency and thus lower limits of detection (LODs). Calibration curves were linear (r 2 >0.996) in the range of 0.2–200μgL−1. LODs for all the TCAs ranged from 0.08 to 0.2μgL−1 using HPLC-DAD. Also an improvement in sensitivity of several orders of magnitude was achieved using single-ion monitoring GC–MS analyses (0.04μgL−1) due to compatibility of this technique with GC instrument. The applicability of the proposed HF-LLLME/GC–MS and HPLC-DAD methods was demonstrated by analyzing the drugs in spiked urine and plasma samples. The obtained recoveries of the drugs in the range of 87.9–109.2% indicated the excellent capability of the developed method for extraction of TCAs from complex matrices. [Copyright &y& Elsevier]

Abstract: A model commonly used to describe the separation of biomolecules was used to simulate the harsh environment when eluting neodymium, samarium, europium and gadolinium with a hot acid. After calibration, the model was used to optimise the preparative separation of europium, as this is the most valuable of the four elements. A kinetic dispersive model with a Langmuir mobile phase modulator isotherm was used to describe the process. The equilibration constant, the stoichiometric coefficient and the column capacity for the components were calibrated. The model fitted the experimental observations well. Optimisation was achieved using a differential evolution method. As the two objective functions used in optimising the process, productivity and yield, are competing objectives, the result was not a single set point but a Pareto front. [Copyright &y& Elsevier]

Abstract: The selectivity window of size-based separations of macromolecules was tailored by tuning the macropore size of polymer monolithic columns. Monolithic materials with pore sizes ranging between 75nm and 1.2μm were prepared in situ in large I.D. columns. The dominant separation mechanism was hydrodynamic chromatography in the flow-through pores. The calibration curves for synthetic polymers matched with the elution behavior by HDC separations in packed columns with ‘analyte-to-pore’ aspect ratios (λ) up to 0.2. For large-macropore monoliths, a deviation in retention behavior was observed for small polystyrene polymers (M r <20kDa), which may be explained by a combined HDC–SEC mechanism for λ <0.02. The availability of monoliths with very narrow pore sizes allowed investigation of separations at high λ values. For high-molecular weight polymers (M r >300,000Da) confined in narrow channels, the separation strongly depended on flow rate. Flow-rate dependent elution behavior was evaluated by calculation of Deborah numbers and confirmed to be outside the scope of classic shear deformation or slalom chromatography. Shear-induced forces acting on the periphery of coiled polymers in solution may be responsible for flow-rate dependent elution. [Copyright &y& Elsevier]

Abstract: Poly(N-isopropylacrylamide) (PIPAAm) brush grafted silica beads, a thermo-responsive chromatographic stationary phase, were prepared through a surface-initiated atom transfer radical polymerization (ATRP) using 2-propanol, N,N-dimethylformamide (DMF), and water as reaction solvents. The rate of grafting PIPAAm on silica bead surfaces was different and found to be dependent on the reactivity of reaction solvent. Temperature-dependent elution profiles of hydrophobic steroids from the prepared-beads-packed columns were found to be different, although the graft amounts of PIPAAm were similar on silica bead surfaces. Especially, prepared beads using 2-propanol exhibited a higher resolution than those using DMF. Calibration curves using glucose and pullulan suggested that beads prepared using DMF prohibited analytes to diffuse into the pores. On the contrary, beads prepared using 2-propanol allowed analytes to diffuse into the pores. The pore diameter of the prepared beads, measured by N2 adsorption–desorption measurement, suggested that beads using 2-propanol has relatively larger pore diameter than those using DMF. Thus, the reaction solvent in surfaces-initiated ATRP affected the grafting configuration of PIPAAm on porous silica-bead surfaces, leading to the different separation efficiency of stationary phase for bioactive compounds. [Copyright &y& Elsevier]

Abstract: This study was undertaken to explore gel permeation chromatography (GPC) for estimating molecular weights of proanthocyanidin fractions isolated from sainfoin (Onobrychis viciifolia). The results were compared with data obtained by thiolytic degradation of the same fractions. Polystyrene, polyethylene glycol and polymethyl methacrylate standards were not suitable for estimating the molecular weights of underivatized proanthocyanidins. Therefore, a novel HPLC–GPC method was developed based on two serially connected PolarGel-L columns using DMF that contained 5% water, 1% acetic acid and 0.15M LiBr at 0.7ml/min and 50°C. This yielded a single calibration curve for galloyl glucoses (trigalloyl glucose, pentagalloyl glucose), ellagitannins (pedunculagin, vescalagin, punicalagin, oenothein B, gemin A), proanthocyanidins (procyanidin B2, cinnamtannin B1), and several other polyphenols (catechin, epicatechin gallate, epicallocatechin gallate, amentoflavone). These GPC predicted molecular weights represented a considerable advance over previously reported HPLC–GPC methods for underivatized proanthocyanidins. [Copyright &y& Elsevier]

Abstract: Odorous emissions from wastewater collection systems and treatment facilities affecting quality of life have given local populations reasons to complain for decades. In order to characterise the composition of such malodorous emissions, a method based on headspace solid-phase microextraction (HS-SPME) and gas chromatography coupled to mass spectrometry (GC–MS) has been developed to determine a list of compounds belonging to different chemical families, which have been previously described as potentially responsible for odour complaints, in wastewater matrices. Some parameters affecting the chromatographic behaviour of the target compounds were studied (e.g. splitless time). Experimental conditions affecting the extraction process (temperature, time and salt content) were evaluated by applying a factorial design at two levels. Using a DVB/CAR/PDMS fibre and the optimised HS-SPME conditions, calibration curves were constructed with detection limits in the range of 0.003–0.6μgL−1. Recovery values higher than 70% and relative standard deviation values between 5 and 16% (n =5) were obtained for all compounds and found to be satisfactory. In wastewater samples, a decrease in the concentration of the analysed compounds through the different treatments was observed. Most of the target analytes were found in influent samples while only octanal and carvone were detected in samples from the plant effluent. [Copyright &y& Elsevier]

Abstract: An experimental design optimization is reported of an analytical procedure used in the simultaneous determination of seven non-steroidal anti-inflammatory drugs (NSAIDs) in bovine milk by gas chromatography with mass spectrometry detection (GC–MS). This analytical procedure involves a solid-phase microextraction (SPME) step and an aqueous derivatization procedure of the NSAIDs to ethyl esters in bovine milk. The following NSAIDs are studied: ibuprofen (IBP), naproxen (NPX), ketoprofen (KPF), diclofenac (DCF), flufenamic acid (FLF), tolfenamic acid (TLF) and meclofenamic acid (MCL). Three kinds of SPME fibers – polyacrylate (PA), polydimethylsiloxane/divinylbenzene (PDMS/DVB) and polydimethylsiloxane (PDMS) – are compared to identify the most suitable one for the extraction process, on the basis of two steps: to determine the equilibrium time of each fiber and to select the fiber that provides the best figures-of-merit values calculated with three-way PARAFAC-based calibration models at the equilibrium time. The best results were obtained with the PDMS fiber. Subsequently, 8 experimental factors (related to the derivatization reaction and the SPME) were optimized by means of a D-optimal design that involves only 14 rather than 512 experiments in the complete factorial design. The responses used in the design are the sample mode loadings of the PARAFAC decomposition which are related to the quantity of each NSAID that is extracted in the experiment. Owing to the fact that each analyte is unequivocally identified in the PARAFAC decomposition, a calibration model is not needed for each experimental condition. The procedure fulfils the performance requirements for a confirmatory method established in European Commission Decision 2002/657/EC. [Copyright &y& Elsevier]

Abstract: We have developed a method for quantification of a specific monoclonal IgM directed toward embryonic stem cells based on a peptide affinity monolith. A peptide affinity ligand with the sequence C–C–H–Q–R–L–S–Q–R–K was obtained by epitope mapping using peptide SPOT synthesis. The peptide ligand was covalently immobilized by coupling the N-terminal cysteine to a monolithic disk that was previously modified with iodated spacer molecules. The monolithic disc was used for quantification of purified IgM and for IgM present in mammalian cell culture supernatant. We observed 17% unspecific binding of IgM to the monolithic disk and additionally a product loss in the flow through of 20%. Nevertheless, calibration curves had high correlation coefficients and inter/intra-assay variability experiments proved sufficient precision of the method. A limit of quantification of 51.69μg/mL for purified IgM and 48.40μg/mL for IgM in cell culture supernatant could be calculated. The binding capacity was consistent within the period of the study which included more than 200 cycles. The analysis time of less than 2min is an advantage over existing chromatographic methods that rely on pore diffusion. [Copyright &y& Elsevier]

Abstract: Folic acid was separated under aqueous normal phase (ANP) conditions with Diamond Hydride™ columns and quantitated in fortified cereal and juice matrices using high performance liquid chromatography/ultraviolet absorption (HPLC-UV) and liquid chromatography/mass spectrometry (LC–MS) based methodologies. The folic acid was well-resolved from matrix components under the ANP conditions studied and allowed for the direct analyses of the fortified juices and cereals without the sample cleanup that is often required for other reported LC-based approaches. The calibration curve obtained from the LC–MS analyses demonstrated good linearity (R 2 =0.9997) in the studied concentration range of 0.05–0.5mg/L. The spiked flour percent recovery was 90% with HPLC-UV and 91% with LC–MS. Spiked juice percent recovery was 102% with LC–MS. However, analyses of juices were unsatisfactory either in terms of recovery or sensitivity. Therefore, analyses of juices will either need to be performed by LC–MS or, if by HPLC-UV, will require sample cleanup. Three cereals and one juice were analyzed with the methods. [Copyright &y& Elsevier]

Abstract: Volatile organic compounds (VOCs) play an important role in the chemistry of the atmosphere and in biogeochemistry. They contribute to the oxidative capacity of the atmosphere, particle and air pollutants, as well as to the production of greenhouse gasses (for instance ozone). Among analytical techniques for their determination in the atmosphere gas chromatography coupled with mass spectrometry (GC–MS) offers several advantages. However, for an accurate quantification calibration with standard substances is necessary. A quantitative structure–property relationship (QSPR) model for the prediction of MS response factors was developed on basis of our experimental measurements for the quantification of ozone precursors present in the atmosphere. A linear correlation between chemical structures and response factors was established by using a 7-parameter MLR model. The average error in the prediction of response factors was calculated by cross-validation procedure and was below 20%, which is sufficient for the determination of VOCs in the air. The proposed procedure is time consuming so it is more suited for the quantification of tentatively identified organic compounds during the reprocessing of MS chromatograms in cases when the original sample is no longer available. [Copyright &y& Elsevier]

Abstract: The use of internal standards in the determination of volatile organic compounds as described in SW-846 Method 8260C introduces a potential for bias in results once the internal standards (ISTDs) are added to a sample for analysis. The bias is relative to the dissimilarity between the analyte and internal standard physical properties that influence how easily analytes are separated from a matrix and concentrated during analysis. Method 5032 is a vacuum distillation procedure for extracting analytes from a sample for use with Method 8260C. Vacuum distillation is also incorporated within another GC/MS analytical procedure, Method 8261A. Method 8260C/5032 and Method 8261A are experimentally identical, however, Method 8261A uses internal standards differently by relating the recovery of each compound to its boiling point and relative volatility. By processing each analysis (water, soil, and biota) using both Method 8260C and Method 8261A, the two approaches are compared on the basis of analyte bias and the failure rate of the quality controls. Analytes were grouped by how similar their boiling points and natural log of their relative volatilities (lnRVs) were to their Method 8260C recommended ISTDs. For the most similar analytes, the Method 8260C determinations yielded an average bias less than 10% and a failure to meet calibration criteria less than 7%. However, as the difference between analyte and ISTD became greater the bias increased to over 40% (matrix dependent) and its calibration failure rate approached 70%. In comparison, when the Method 8260C data were reprocessed as Method 8261A determinations, this trend for groupings was minimized with biases increasing from 6% to only 20% and the calibration failure rate went from 0% to 15%. [ABSTRACT FROM AUTHOR]

Abstract: The phenomenon known as “matrix-induced enhancement effect” is not only observed in the analysis of pesticides in food, but also in Chinese herbs. Several approaches have been proposed to overcome the matrix-induced effect, but each method has serious limitations. Compared with standard calibration methods, the procedure with adding analyte protectants offers a more convenient and effective route to solve the problem. In the current study, we have analyzed 195 types of pesticides in Chinese herbs by gas chromatography–mass spectrometry (GC–MS), and the compounds that are susceptible to matrix effect were picked up and confirmed. In addition, several analyte protectants were evaluated and the most effective combination was determined. d-Ribonic acid-γ-lactone (2mg/ml) and d-sorbitol (1mg/ml) were shown to be the best analyte protectants for the analysis of most pesticides. [Copyright &y& Elsevier]

Abstract: A simple and cost effective permeation passive sampler equipped with a polydimethylsiloxane (PDMS) membrane was designed for the determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air. Permeation passive samplers have significant advantages over diffusive passive samplers, including insensitivity to moisture and high face velocities of air across the surface of the sampler. Calibration constants of the sampler towards 41 analytes belonging to alkane, aromatic hydrocarbon, chlorinated hydrocarbon, ester and alcohol groups were determined. The calibration constants allowed for the determination of the permeability of PDMS towards the selected analytes. They ranged from 0.026cm2 min−1 for 1,1-dichloroethylene to 0.605cm2 min−1 for n-octanol. Further, the mechanism of analyte transport across PDMS membranes allowed for the calibration constants of the sampler to be estimated from the linear temperature programmed retention indices (LTPRI) of the analytes, determined using GC columns coated with pure PDMS stationary phases. Statistical analysis using Student''s t test indicated that there was no significant difference at the 95% probability level between the experimentally obtained calibration constants and those estimated using LTPRI for most analyte groups studied. This correlation allows the estimation of the calibration constants of compounds not known to be present at the time of sampler deployment, which makes it possible to determine parameters like total petroleum hydrocarbons in the vapor phase. [Copyright &y& Elsevier]

Abstract: A novel ionic liquid (IL) bonded fused-sil-ica fiber for headspace solid-phase microextraction (HS-SPME)/gas chromatography-flame ionization detection (GC-FID) of methyl tert-butyl ether (MTBE) in a gasoline sample was prepared and used. The new proposed chemically bonded fiber has better thermal stability and durability than its corresponding physically coated fiber. Another advantage is that no spacer was used for the purpose of bonding the IL to the surface of the fused-silica. The latter advantage makes the preparation of these fibers easier with lower cost than those prepared using sol–gel method. The ionic liquid 1-methyl-3-(3-trimethoxysilyl propyl) imidazolium bis(trifluoromethylsulfonyl) imide was synthesized and cross linked to the surface of the fused-silica fiber. Then, the chemically IL-modified fibers were applied to the headspace extraction of MTBE. The chemically IL-modified fibers showed improved thermal stability at temperatures up to 220°C relative to the physically IL-modified fibers (180°C). The chemically bonded IL film on the surface of the fused-silica fiber was durable over 16 headspace extractions without any significant loss of the IL film. The calibration graph was linear in a concentration range of 2–240μgL−1 (R 2 =0.996) with the detection limit of 0.1μgL−1 level. The reproducibility (RSD %, n =6) of the new IL bonded fused-silica fiber (8.9%) was better than the physically coated fiber (12%) suggesting that the proposed chemically IL-modified fiber is more robust than the physically IL-modified fiber. The optimum extraction conditions were the followings: 40°C extraction temperature, 12min extraction time, 30s desorption time and sample agitation at 200rpm. [ABSTRACT FROM AUTHOR]

Abstract: In chromatography-based metabonomic research, retention time (RT) alignment of chromatographic peaks poses a challenge for the accurate profiling of biomarkers. Although a number of RT alignment software has been reported, the performance of these software packages have not been comprehensively evaluated. This study aimed to evaluate the RT alignment accuracy of publicly available and commercial RT alignment software. Two gas chromatography/mass spectrometry (GC/MS) datasets acquired from a mixture of standard metabolites and human bladder cancer urine samples, were used to assess three publicly available software packages, MetAlign, MZmine and TagFinder, and two commercial applications comprising the Calibration feature and Statistical Compare of ChromaTOF software. The overall RT alignment accuracies in aligning standard compounds mixture were 93, 92, 74, 73 and 42% for Calibration feature, MZmine, MetAlign, Statistical Compare and TagFinder, respectively. Additionally, unique trends were observed for the individual software with regards to the different experimental conditions related to extent and direction of RT shifts. Conflicting performance was observed for human urine samples suggesting that RT misalignments still occurred despite the use of RT alignment software. While RT alignment remains an inevitable step in data preprocessing, metabonomic researchers are recommended to perform manual check on the RT alignment of important biomarkers as part of their validation process. [ABSTRACT FROM AUTHOR]

Abstract: A novel solid-phase microextraction fiber based on a stainless steel wire coated with Au nanoparticles was prepared and has been applied, coupled with gas chromatography, to the extraction of aromatic hydrophobic organic chemical pollutants in rainwater and soil extract. The solid-phase microextraction fiber exhibited excellent extraction efficiency and selectivity. Effects of extraction time, extraction temperature, ionic strength, stirring rate and desorption conditions were investigated and optimized. Single fiber repeatability and fiber-to-fiber reproducibility were less than 7.90% and 26.40%, respectively. The calibration curves were linear in a wide range for all analytes. Correlation coefficients ranged from 0.9941 to 0.9993. The as-established SPME-GC method was used successfully to two real natural samples. Recovery of analytes spiked at 10μgL−1 and 100μgL−1 ranged from 78.4% to 119.9% and the relative standard deviations were less than 11.3%. [ABSTRACT FROM AUTHOR]

Abstract: The development of a two phase hollow fiber liquid-phase microextraction technique, followed by gas-chromatography-flame ionization detection (GC-FID) for the profiling of the fatty acids (FAs) (lauric, myristic, palmitic, stearic, palmitoleic, oleic, linoleic, linolenic and arachidic) in vegetable oils is described. Heptadecanoic acid methyl ester was used as the internal standard. The FAs were transesterified to their corresponding methyl esters prior to the extraction. Extraction parameters such as type of extracting solvent, temperature, extraction time, stirring speed and salt addition were studied and optimized. Recommended conditions were extraction solvent, n-tridecane; extraction time, 35min; extraction temperature, ambient; without addition of salt. Enrichment factors varying from 37 to 115 were achieved. Calibration curves for the nine FAs were well correlated (r 2 >0.994) within the range of 10–5000μgL−1. The limit of detection (signal:noise, 3) was 4.73–13.21ngL−1. The method was successfully applied to the profiling of the FAs in palm oils (crude, olein, kernel, and carotino cooking oil) and other vegetable oils (soybean, olive, coconut, rice bran and pumpkin). The encouraging enrichments achieved offer an interesting option for the profiling of the minor and major FAs in palm and other vegetable oils. [ABSTRACT FROM AUTHOR]

Abstract: We have analyzed phosphorus in an enzymatically digested DNA molecule using capillary electrophoresis (CE) hyphenated with inductively coupled plasma mass spectrometry (ICP-MS). The DNA concentration was quantified by the phosphorus value obtained in the CE-ICP-MS analysis. The CE-ICP-MS measurement, for which the interface device AIF-01 equipped three layered nebulizer was adopted, was achieved with limited μL/min nebulizing without loss of sample in the vaporizing chamber. The samples of nucleotides and free phosphate were separated well in the CE-ICP-MS measurement, and the calibration curve (0.1–10μg/mL) of the phosphorus showed a linear (R 2 =0.999) increase in intensity. After digestion of the 100-bp double-strand DNA sample to deoxyribonucleotide-5′-monophosphates (dNMPs) by phosphodiesterase-I, phosphorus was detected by CE-ICP-MS without further purification steps. In this study, we applied two calculation schemes of DNA analysis using a dNMP concentration obtained from CE-ICP-MS. Comparative CE-ICP-MS analysis with DNA digested to dNMPs showed that the assay gave an equal value obtained from the total DNA quantification using fluorescence detection. The detection limits of the DNA sample obtained from these species and phosphorus in nucleotides using CE-ICP-MS were 3.1–26ng/mL. These LOD values were equal to the conventional fluorescence determination of DNA. [ABSTRACT FROM AUTHOR]

Abstract: A novel analytical method is reported that combines continuous solid-phase extraction and gas chromatography for the determination of 22 carboxylic acids in water. The highly polar and hydrophilic analytes were preferentially sorbed on a mixture of LiChrolut EN–Supelclean ENVI-18 (1:1) sorbent column and eluted with methanol; this extraction process did not require derivatisation. The extract was analysed by gas chromatography coupled to a flame ionisation detector as well as a mass spectrometer with electron impact (EI) or positive chemical ionisation modes. The highest sensitivity was achieved when using MS-EI, with good linearity in calibration curves and low detection limits (2–40ngL−1) for 50mL of sample. The entire procedure from raw aqueous sample to a ready-to-inject methanol solution of the acids requires less than 15min. Another benefit of this method is the good accuracy (recoveries between 93 and 102%) and precision (relative standard deviation, 3.4–6.2%), which allows the determination of carboxylic acids in environmental water and in real chlorinated and ozonated drinking water. [ABSTRACT FROM AUTHOR]

Abstract: Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–mass spectrometry-selective ion monitoring (GC–MS-SIM) was applied to the determination of methyl tert-butyl ether (MTBE) in water samples. The effect of main parameters affecting the extraction efficiency was studied simultaneously. From selected parameters, volume of extraction solvent, volume of dispersive solvent, and salt concentration were optimized by means of experimental design. The statistical parameters of the derived model were R 2 =0.9987 and F =17.83. The optimal conditions were 42.0μL for extraction solvent, 0.30mL for disperser solvent and 5% (w/v) for sodium chloride. The calibration linear range was 0.001–370μgL−1. The improved detection limit with the aid of chemometrics was 0.3ngL−1. The relative standard deviation (RSD) with n =9 for 0.1mgL−1 MTBE in water with and without internal standard was 2.7% and 3.1%, respectively. Under the optimal conditions, the relative recoveries of spiked MTBE in different water samples were in the range of 100–105%. [ABSTRACT FROM AUTHOR]

Abstract: A novel molecular complex-based dispersive liquid–liquid microextraction (DLLME) method was established via hydrogen bond interaction between the extractant and the analytes. In this approach, tri-n-butylphosphate (TBP), a Lewis base, was directly used, instead of the traditional water-immiscible organic solvents, as the extractant for DLLME. The phenols (p-benzenediol, m-benzenediol, o-benzenediol and phenol), which are typical Lewis acids, were successfully extracted from environmental aqueous samples. In addition, phase separation was achieved in a disposable polyethylene pipet with the open and narrow tip upside, for a collection of the above extractant layer, i.e. TBP. To achieve satisfactory extraction performance, several extraction parameters, such as type of extractant solvents, extractant volume, pH of sample solution, ionic strength of sample solution and extraction time, were optimized. Additionally, the proposed method was applied to environmental water samples. Under the optimized conditions, the limits of detection and limits of quantification for the phenols were 7–29 and 25–98μg/L, respectively. The calibration curves showed good linearity (r 2 ≥0.9961) over the investigated concentration range. The repeatability of the method was investigated by evaluating the intra- and inter-day precisions. The relative standard deviations (RSDs) obtained were lower than 11.2% and 13.9% at different concentration levels. The recoveries ranged from 83.2% to 117.8%, with RSDs less than 13.1%. The developed approach provides a new way to facilitate DLLME of organic polar compounds from aqueous solutions. Moreover, it enables a convenient collection of solvent less dense making use of a cheap and disposable polyethylene pipet. [ABSTRACT FROM AUTHOR]

Abstract: A multi-residue methodology based on a solid phase extraction followed by gas chromatography–tandem mass spectrometry was developed for trace analysis of 32 compounds in water matrices, including estrogens and several pesticides from different chemical families, some of them with endocrine disrupting properties. Matrix standard calibration solutions were prepared by adding known amounts of the analytes to a residue-free sample to compensate matrix-induced chromatographic response enhancement observed for certain pesticides. Validation was done mainly according to the International Conference on Harmonisation recommendations, as well as some European and American validation guidelines with specifications for pesticides analysis and/or GC–MS methodology. As the assumption of homoscedasticity was not met for analytical data, weighted least squares linear regression procedure was applied as a simple and effective way to counteract the greater influence of the greater concentrations on the fitted regression line, improving accuracy at the lower end of the calibration curve. The method was considered validated for 31 compounds after consistent evaluation of the key analytical parameters: specificity, linearity, limit of detection and quantification, range, precision, accuracy, extraction efficiency, stability and robustness. [ABSTRACT FROM AUTHOR]

A robust method for reduction of instrument differences, the vector of calibration ratios, was developed to eliminate differences in unit resolution mass spectra of fatty acid methyl esters (FAME) caused by experimental conditions. Mass spectra of FAMEs were analyzed by two different mass spectrometers and after application of different tune procedures. The proposed method could remove 51–95% of the systematic difference in spectra caused by instrumental conditions. Highly similar spectra, which were incorrectly identified because of the contribution from experimental conditions, could be correctly identified after application of the calibration vector. The proposed method is simple, easy to implement and shows robustness when applied on spectra that is outside the range spanned by the calibration sample. [ABSTRACT FROM AUTHOR]

Abstract: A simple solvent microextraction method termed vortex-assisted liquid–liquid microextraction (VALLME) coupled with gas chromatography micro electron-capture detector (GC-μECD) has been developed and used for the pesticide residue analysis in water samples. In the VALLME method, aliquots of 30μL toluene used as extraction solvent were directly injected into a 25mL volumetric flask containing the water sample. The extraction solvent was dispersed into the water phase under vigorously shaking with the vortex. The parameters affecting the extraction efficiency of the proposed VALLME such as extraction solvent, vortex time, volumes of extraction solvent and salt addition were investigated. Under the optimum condition, enrichment factors (EFs) in a range of 835–1115 and limits of detection below 0.010μgL−1 were obtained for the determination of target pesticides in water. The calculated calibration curves provide high levels of linearity yielding correlation coefficients (r 2) greater than 0.9958 with the concentration level ranged from 0.05 to 2.5μgL−1. Finally, the proposed method has been successfully applied to the determination of pesticides from real water samples and acceptable recoveries over the range of 72–106.3% were obtained. [ABSTRACT FROM AUTHOR]

Abstract: An ionic liquid-based single-drop microextraction (IL-SDME) procedure using IL as an extractant on-line coupled to capillary electrophoresis (CE) is proposed. The method is capable of quantifying trace amounts of phenols in environmental water samples. For the SDME of three phenols, a 2.40nL IL microdrop was exposed for 10min to the aqueous sample and then was directly injected into the capillary column for analysis. Extraction parameters such as the extraction time, the IL single-drop volume, pH of the sample solution, ionic strength, volume of the sample solution and the extraction temperature were systematically investigated. Detection limits to three phenols were less than 0.05μgmL−1, and their calibration curves were all linear (R 2 ≥0.9994) in the range from 0.05 to 50μgmL−1. And enrichment factors for three phenols were 156, 107 and 257 without agitation, respectively. This method was then utilized to analyze two real environmental samples from Yellow River and tap water, obtaining satisfactory results. Compared with the usual SDME for CE, IL-SDME–CE is a simple, low-cost, fast and environmentally friendly preconcentration technique. [Copyright &y& Elsevier]

The increasing occurrence of toxic cyanobacterial blooms has led to a requirement for robust monitoring strategies and whilst several validated procedures have been developed these can be limited by the lack of high quality calibration standards. High quality standards must have confirmation of identity, purity and concentration by multiple methods. One aspect, purity, is rarely addressed but is essential. This is the first evaluation of the charged aerosol detector (CAD) to determine the benefits of incorporating a universal detector for more accurate purity determination of these peptides. Microcystins were detected at 5–10ng on the column using the CAD, providing comparable quantification limits to those obtained using traditional UV detection. Purity determination of test compounds that had been partially purified, had showed that highest purity was at 238nm>UV TIC>ESI TIC>CAD indicating that increased impurities could be detected using the CAD thus providing a more accurate indication of compound quality. Compounds purified by preparative HPLC were shown to have relative purities between 97% and 99%, however, when evaluated by CAD this dropped to 90–94% supporting the multi-detector strategy as essential for production of high quality compounds. [Copyright &y& Elsevier]

Abstract: A new method based on liquid–liquid–liquid microextraction combined with electrospray ionization-ion mobility spectrometry (LLLME-ESI-IMS) was used for the determination of pentazocine in urine and plasma samples. Experimental parameters which control the performance of LLLME, such as selection of composition of donor and acceptor phase, type of organic solvent, ionic strength of the sample, extraction temperature and extraction time were studied. The limit of detection and relative standard deviation of the method were 2ng/mL and 5.3%, respectively. The linear calibration ranged from 10 to 500ng/mL with r 2 =0.998. Pentazocine was successfully determined in urine and plasma samples without any significant matrix effect. [Copyright &y& Elsevier]

Abstract: The goal of the present work is to apply the versatile asymmetrical flow field-flow fractionation (AF4) coupled to UV and light scattering detection for the characterization of hyperbranched poly(ethylene imine) decorated with maltose shell (PEI-Mal) and the polar dye Rose Bengal (RB) in respect to their complexation behaviour. The quantitative determination of the non-complexed dye was carried out using the ultra-filtration effect of AF4 during the focussing phase, whereas the non-bound RB is filtrated and transported out of the channel while the complex of RB and PEI-Mal remains inside. A calibration with UV detector (550nm) was established and different parameters (e.g. membrane material, molecular weight cut-off and stability of both, pure RB and RB@PEI-Mal complexes in solution) were investigated and verified. Successful reproducibility tests were performed. First complexation studies with the developed method were applied successfully with different mixture compositions of RB and PEI-Mal. [Copyright &y& Elsevier]

Abstract: A method aimed to obtain the relative abundances of all molecular species in highly overlapped mass spectra is presented. Its performance is demonstrated with an example of matrix-assisted laser desorption ionization (MALDI) spectra obtained from a polysterene-co-polyisoprene sample, retrieving the full co-polymer architecture. The method is based on a multiple regression operation, applied locally at consecutive regions. The method is designed in such a way that it is not necessary to locate regions in the spectrum that are not influenced by adjacent ones. This increases its applicability, since the method is able to tackle the analysis of highly complex spectra, tending to minimise the need of user intervention. The method allows to correct for non-idealities (such as wrong calibration) or to adjust the variations of spectral resolution with mass. Additionally, the algorithm calculates the precision of the computation in a straightforward way. [Copyright &y& Elsevier]

Abstract: The primary objective of this review is to discuss recent technological developments in the field of solid-phase microextraction that have enhanced the utility of this sample preparation technique in the field of bioanalysis. These developments include introduction of various new biocompatible coating phases suitable for bioanalysis, such as commercial prototype in vivo SPME devices, as well as the development of sampling interfaces that extend the use of this methodology to small animals such as mice. These new devices permit application of in vivo SPME to a variety of analyses, including pharmacokinetics, bioaccumulation and metabolomics studies, with good temporal and spatial resolution. New calibration approaches have also been introduced to facilitate in vivo studies and provide fast and quantitative results without the need to achieve equilibrium. In combination with the drastic improvement in the analytical sensitivity of modern liquid chromatography–tandem mass spectrometry instrumentation, full potential of in vivo SPME as a sample preparation tool in life sciences can finally be explored. From the instrumentation perspective, SPME was successfully automated in 96-well format for the first time. This opens up new opportunities for high-throughput applications (>1000 samples/day) such as for the determination of unbound and total drug concentrations in complex matrices such as whole blood with no need for sample pretreatment, studies of distribution of drugs in various compartments and/or determination of plasma protein binding and other ligand–receptor binding studies, and this review will summarize the progress in this research area to date. [Copyright &y& Elsevier]

Abstract: This paper described a convenient semiquantitative method for colorimetric detection of protein with self-calibration integrated on the test strip. Hydrophilic paper was employed as microfluidic device for running colorimetric assay, tree-shaped design was developed to ensure uniform microfluidic flow for multiple branches. The approach was validated with bovine serum albumin (BSA) colorimetric detection, and colorimetric results observed by naked eyes were consistent with that from apparatus. The device could be coupled with digital transmission of images for remote monitoring system for diagnosis, food control, and environmental analysis. [Copyright &y& Elsevier]

Abstract: An analytical method combining both a simple, fast and efficient solvent microextraction and a sensitive and selective monitoring mode, based on ion isolation ion-trap mass spectrometry (MS), was developed for analysis of perfluorinated compounds (PFCs) in biota. The method involved the vortex-shaking of 0.2g of tissue sample and 800μL of tetrahydrofuran (THF):water (75:25, v/v) for 7min, subsequent centrifugation for 13min and direct quantitation of PFCs in the extract against solvent-based calibration curves. Selection of solvent composition was based on Hildebrand solubility parameters and their components (i.e. dispersion, dipole–dipole and hydrogen bonding forces). Recoveries in samples for PFCs with hydrocarbon chain lengths between C4 and C14 ranged from 85 to 111%, with relative standard deviations between 1 and 11%. The ion isolation monitoring mode, proposed for the first time for ion-trap-MS quantitation, proved to be effective in avoiding space-charge effects caused by co-eluting matrix components while keeping the sensitivity of full scan MS operation. Detection limits of the method were in the range 0.8−6ngg−1 for perfluoroalkyl carboxylates (PFACs) and 0.4–0.8ngg−1 for perfluoroalkyl sulfonates (PFASs) in wet weight samples. The method was validated using a reference material made up of flounder muscle and by comparison with triple quadrupole MS measurements and it was applied to the determination of PFCs in liver and muscle samples from sea birds and fishes. Only PFASs were found in samples at quantifiable levels (2.9 and 13.1ngg−1) while PFACs were below the respective quantitation limits. This method allows quick and simple microextraction of PFCs with minimal solvent consumption, while delivering accurate and precise data. [Copyright &y& Elsevier]

Abstract: A supramolecular solvent made up of reverse micelles of decanoic acid, dispersed in a continuous phase of THF:water, was proposed for the simple, fast and efficient microextraction of OTA in wheat prior to liquid chromatography-fluorescence determination. The method involved the stirring of 300 mg-wheat subsamples (particle size 50μm) and 350μL of supramolecular solvent for 15min, subsequent centrifugation for 15min and the direct quantitation of OTA in the extract, previous 5.7-fold dilution with ethanol/water/acetic acid (49.5/49.5/1), against solvent-based calibration curves. No clean-up of the extracts or solvent evaporation was needed. Interactions between the supramolecular solvent and major matrix components in the wheat (i.e. carbohydrates, lipids and proteins) were investigated. The reverse micelles in the extractant induced gluten flocculation but only in the coacervation region of lower analytical interest (i.e. at percentages of THF above 11%). The quantitation of OTA was interference-free. Representativity of the 300 mg-wheat subsamples was proved by analysing a reference material. OTA recoveries in wheat ranged between 84% and 95% and the precision of the method, expressed as relative standard deviation, was 2%. The quantitation limit of the method was 1.5μgkg−1 and was below the threshold limit established for OTA in raw cereals by EU directives (5.0μgkg−1). The method developed was validated by using a certified reference material and it was successfully applied to the determination of OTA in different wheat varieties from crops harvested in the South of Spain. OTA was not detected in any of the analysed samples. This method allows quick and simple microextraction of OTA with minimal solvent consumption, while delivering accurate and precise data. [Copyright &y& Elsevier]

Abstract: A condensation nucleation light scattering detector (CNLSD) was adapted for use as a detector for supercritical fluid chromatography. The performance of the CNLSD was evaluated and compared to evaporative light-scattering detector (ELSD) using a well-defined equimass mixture of uniform poly(ethylene glycol) oligomers and a certified reference material of poly(ethylene glycol) 1000. The CNLSD was able to detect a 10 times less concentrated solution of uniform oligomers compared to the ELSD. The quantitativeness of CNLSD was high enough to obtain the molecular mass distribution of poly(ethylene glycol) 1000 without any calibrations; on the other hand, the original data measured by ELSD was about 4% smaller than the certified value of poly(ethylene glycol) 1000. The CNLSD was suitable for supercritical fluid chromatography as a mass concentration detector. [Copyright &y& Elsevier]

Abstract: A simple and efficient dual preconcentration method of on-column liquid–liquid–liquid microextraction (LLLME) coupled with base stacking was developed for capillary zone electrophoresis (CZE) in this paper. Four N-methyl carbamates were used as target compounds to evaluate the enrichment means. The carbamates in sample solutions (donor phase) were extracted into a dodecanol phase immobilized on a porous hollow fiber, hydrolyzed and back extracted into 0.20μL running buffer (acceptor phase) of 30mmol/L methylamine hydrochloride (pH 11.6) containing 0.5mmol/L tetradecyltrimethylammonium bromide inside the hollow fiber, stacked further with 0.5mol/L NaOH injected at −10kV for 60s, and separated by CZE. Analytical parameters affecting the LLLME, base stacking and CZE were investigated, including sample solution volume, pH and temperature, extraction time, stirring rate, buffer component, buffer pH, NaOH concentration, stacking time, etc. The enrichment factors of the carbamates were higher than 1100. The relative standard deviation (RSD) of peak height and limits of detection (LODs) were 4.5–5.5% (n =6) and 2–4ng/mL (S/N =3) for standard solutions, respectively. The proposed method was applied to the analysis of vegetable and fruit samples with the RSD less than 6.0% (n =3) and LODs of 6–10ng/g (S/N =3). The calibration solutions were prepared by diluting the stock solutions with blank sample solutions, and the calibration concentrations ranged from 0.012 to 1.0μg/mL (r >0.9951). The analytical results demonstrated that the LLLME coupled with base stacking was a simple, convenient and reliable on-column sample pretreatment method for the analysis of anionic analytes in CZE. [Copyright &y& Elsevier]

Abstract: High-performance monolith affinity chromatography employing protein A resins has been introduced previously for the fast purification of IgG from different sources. Here we describe the design and evaluation of a fast and specific method for quantitation of IgG from purified samples as well as crude supernatant from Chinese hamster ovary (CHO) cells. We used a commercially available affinity monolith with protein A as affinity ligand (CIM protein A HLD disk). Interferences of CHO host cell proteins with the quantitation of IgG from CHO supernatant were eliminated by a careful choice of the equilibration buffer. With this method developed, it is possible to quantify IgG within 5min in a concentration range of 23–250μg/ml. The calibration range of the method could be extended from 4 to 1000μg/ml by adjusting the injection volume. The method was successfully validated by measuring the low limit of detection and quantification, inter- and intra-day precision and selectivity. [Copyright &y& Elsevier]

Abstract: A simple, efficient, innovative and environmentally friendly analytical technique was successfully applied for the first time for the extraction and preconcentration of polybrominated diphenyl ethers (PBDEs) from water samples. The PBDEs selected for this work were those most commonly found in the literature in natural water samples: 2,2′,4,4′-tetraBDE (BDE-47), 2,2′,4,4,5-pentaBDE (BDE-99), 2,2′,4,4,6-pentaBDE (BDE-100) and 2,2,4,4′,5,5′-hexaBDE (BDE-153). The extracted PBDEs were separated and determined by gas chromatography–mass spectrometry (GC–MS). The extraction/preconcentration technique is based on ultrasound-assisted emulsification-microextraction (USAEME) of a water-immiscible solvent in an aqueous medium. Several variables including, solvent type, extraction time, extraction temperature and matrix modifiers were studied and optimized over the relative response the target analytes. Chloroform was used as extraction solvent in the USAEME technique. Under optimum conditions, the target analytes were quantitatively extracted achieving enrichment factors (EF) higher than 319. The detection limits (LODs) of the analytes for the preconcentration of 10mL sample volume were within the range 1–2pgmL−1. The relative standard deviations (RSD) for five replicates at 10pgmL−1 concentration level were <10.3%. The calibration graphs were linear within the concentration range of 5–5000pgmL−1 for BDE-47 and BDE-100; and 5–10,000pgmL−1 for BDE-99 and BDE-153, respectively. The coefficients of estimation were ≥0.9985. Validation of the methodology was performed by standard addition method at two concentration levels (10 and 50pgmL−1). Recovery values were ≥96%, which showed a successful robustness of the analytical methodology for determination of picogram per milliliter of PBDEs in water samples. Significant quantities of PBDEs were not found in the analyzed samples. [Copyright &y& Elsevier]