Search

We have developed, manufactured, and tested a new feed design for interferometric radio telescopes with "large-N, small-D" designs. Such arrays require low-cost and low-complexity feeds for mass production on reasonable timescales and budgets, and also require those feeds to be compact to minimize obstruction of the dishes, along with having ultra-wide frequency bands of operation for most current and future science goals. The feed presented in this paper modifies the exponentially tapered slot antenna (Vivaldi) and quad-ridged flared horn antenna designs by having an oversized backshort, a novel method of maintaining a small size that is well-suited for deeper dishes (f ∕ D ≤ 0. 2 5). It is made of laser cut aluminum and printed circuit boards, such that it is inexpensive (≲ 7 5 USD per feed in large-scale production) and quick to build; it has a 5:1 frequency ratio, and its size is approximately a third of its longest operating wavelength. We present the science and engineering constraints that went into design decisions, the development and optimization process, and the simulated performance. A version of this feed design was optimized and fabricated for the Canadian Hydrogen Observatory and Radio-transient Detector (CHORD) prototypes. When simulated on CHORD's very deep dishes (f ∕ D = 0. 2 1) and with CHORD's custom first-stage amplifiers, the on-sky system temperature T sys of the complete receiving system from dish to digitizer remains below 30 K over most of the 0.3–1.5 GHz band, and maintains an aperture efficiency η A between 0.4 and 0.6. The entire receiving chain operates at ambient temperature. The feed is designed to slightly under-illuminate the CHORD dishes, in order to minimize coupling between array elements and spillover. [ABSTRACT FROM AUTHOR]

Foreground mitigation is critical to all next-generation radio interferometers that target cosmology using the redshifted neutral hydrogen 21 cm emission line. Attempts to remove this foreground emission have led to new analysis techniques as well as new developments in hardware specifically dedicated to instrument beam and gain calibration, including stabilized signal injection into the interferometric array and drone-based platforms for beam mapping. The radio calibration sources currently used in the literature are broad-band incoherent sources that can only be detected as excess power and with no direct sensitivity to phase information. In this paper, we describe a digital radio source which uses Global Positioning Satellite (GPS) derived time stamps to form a deterministic signal that can be broadcast from an aerial platform. A copy of this source can be deployed locally at the instrument correlator such that the received signal from the aerial platform can be correlated with the local copy, and the resulting correlation can be measured in both amplitude and phase for each interferometric element. We define the requirements for such a source, describe an initial implementation and verification of this source using commercial Software Defined Radio boards, and present beam map slices from antenna range measurements using the commercial boards. We found that the commercial board did not meet all requirements, so we also suggest future directions using a more sophisticated chipset. [ABSTRACT FROM AUTHOR]

This paper is about the Data Processing Center (DPC) working within the RadioAstron project. Since the launch of the space radio telescope to orbit in July 2011, the DPC underwent significant quantitative and qualitative changes as the project developed. This paper describes the schemes, structure, stages of the processing center development, current upgrades and new technologies introduced in the DPC throughout the entire period of its operation. For technical reasons, the scheduled observations in the project were terminated in January 2019. However, still the work of the DPC continued. Today, the most valuable thing we have is information. There is now a unique archive of service and scientific data of the project in our possession, and a data bank of the RadioAstron project is underway, which will ensure a proper access to scientific and service information for all interested experts, as well as provide an opportunity for an additional data analysis. [ABSTRACT FROM AUTHOR]

Since the fall of the Arecibo 305 m telescope platform on 2020 December 1, there has been much discussion of building a new Arecibo telescope or rebuilding the facility that was destroyed. In the collapse, the top of the three platform support towers was sheared off, and the feed arm fell free from the swinging platform and destroyed 25% of the dish. Fortunately, the Control Building, the home of the computers, spectrometers, masers, atomic clocks, 430 MHz Klystrons, etc., was spared. By replacing the main dish support cables and resurfacing with coarse mesh, the main dish can be repaired as a reflector for < HF operation. By replacing the damaged aluminum panels to make the dish whole again, RF operations at up to 500 MHz can be resumed. In this paper, we outline the steps that can be taken to restore High Frequency (HF, 3–30 MHz) ionospheric heating, 430 MHz ionospheric incoherent scattering radar, passive radio observations of satellite arcing and pulsars, and to extend the field of regard to 47∘ from the zenith. This would restore and improve much of the utility of the Arecibo dish. Part of this plan involves supporting, positioning and pointing novel point feeds from lightweight football-camera-like cables, strung from the rebuilt tower tops. It is believed that the dish may thus become broadly useful long before replacement facilities can be engineered and constructed. [ABSTRACT FROM AUTHOR]

The Mexican Array Radio Telescope (MEXART), located in the state of Michoacan in Mexico, has been operating in an analog fashion, utilizing a Butler Matrix to generate fixed beams on the sky, since its inception. Calibrating this instrument has proved difficult, leading to loss in sensitivity. It was also a rigid setup, requiring manual intervention and tuning for different observation requirements. The Radio Frequency (RF) system has now been replaced with a digital one. This digital backend is a hybrid system utilizing both FPGA-based technology and GPU acceleration, and is capable of automatically calibrating the different rows of the array, as well as generating a configurable number of frequency-domain synthesized beams to towards selected locations on the sky. A monitoring and control system, together with a full-featured web-based front-end, has also been developed, greatly simplifying the interaction with the instrument. This paper presents the design, implementation and deployment of the new digital backend, including preliminary analysis of system performance and stability. [ABSTRACT FROM AUTHOR]

With the ongoing growth in radio communications, there is an increased contamination of radio astronomical source data, which hinders the study of celestial radio sources. In many cases, fast mitigation of strong radio frequency interference (RFI) is valuable for studying short lived radio transients so that the astronomers can perform detailed observations of celestial radio sources. The standard method to manually excise contaminated blocks in time and frequency makes the removed data useless for radio astronomy analyses. This motivates the need for better RFI mitigation techniques for array of size M antennas. Although many solutions for mitigating strong RFI improves the quality of the final celestial source signal, many standard approaches require all the eigenvalues of the spatial covariance matrix (R ∈ ℂ M × M ) of the received signal, which has O (M 3) computation complexity for removing RFI of size d where d ≪ M. In this work, we investigate two approaches for RFI mitigation, (1) the computationally efficient Lanczos method based on the Quadratic Mean to Arithmetic Mean (QMAM) approach using information from previously-collected data under similar radio-sky-conditions, and (2) an approach using a celestial source as a reference for RFI mitigation. QMAM uses the Lanczos method for finding the Rayleigh–Ritz values of the covariance matrix R , thus, reducing the computational complexity of the overall approach to O (d M 2). Our numerical results, using data from the radio observatory Long Wavelength Array (LWA-1), demonstrate the effectiveness of both proposed approaches to remove strong RFI, with the QMAM-based approach still being computationally efficient. [ABSTRACT FROM AUTHOR]

Electromagnetic radiation from human activities, known as man-made Radio Frequency Interference (RFI), adversely affects radio astronomy observations. In the vicinity of the Upgraded Giant Metrewave Radio Telescope (uGMRT) array, the sparking on power lines is the major cause of interference at observing frequencies less than 800 MHz. A real-time broadband RFI detection and filtering system is implemented as part of the uGMRT wideband signal processing backend to mitigate the effect of broadband RFI. Performance analysis techniques used for testing and commissioning the system for observations in the beamformer and correlator modes of the uGMRT are presented. The concept and implementation of recording simultaneous unfiltered and filtered data along with data analysis and interpretation is illustrated using an example. For the beamformer mode, spectrogram, single spectral channel, and its Fourier transform is used for performance analysis whereas, in the correlator mode, the cross-correlation function, closure phase, and visibilities from the simultaneously recorded unfiltered and filtered is carried out. These techniques are used for testing the performance of the broadband RFI filter and releasing it for uGMRT users. [ABSTRACT FROM AUTHOR]