Search

Ga-rich zones created along macrosteps in n-AlGaN plausibly function as electron pathways of AlGaN-based deep-ultraviolet (DUV) LEDs fabricated on AlN templates using 1.0°-miscut c(0001) sapphire substrates toward the m[1-100] axis. This work was performed to clarify AlN mole fractions (xAl) of Ga-rich zones. xAl ≃ (7/12, 6/12, and 5/12) was observed in Ga-rich zones in AlαGa1−αN (α ≃ 0.63, 0.55, and 0.43, respectively) by the method proposed in our previous article in which we showed that Ga-rich zones of Al8/12Ga4/12N were created in Al0.7Ga0.3N. xAl in the Ga-rich zones obtained from an energy-dispersive x-ray signal by scanning transmission electron microscopy calibrated by Rutherford backscattering well agreed with xAl obtained by cross-sectional cathodoluminescence (CL) spectroscopy using scanning electron microscopy. A weak CL shoulder peak corresponding to Al4/12Ga8/12N was also observed for Al0.43Ga0.57N. In addition, xAl ≃ n/12 (n = 6–9) in Al-rich zones appeared in the rest of the Ga-rich zones. Furthermore, nanobeam electron diffraction patterns of the Ga-rich zones indicated a high possibility of a regular configuration of Ga and Al atoms on the c(0001) plane in our samples. Consequently, xAl values in nonflat AlGaN layers with macrosteps were often determined to be near n/12 (n: integer). Thus, Ga-rich zones (xAl = n/12: n = 4–8) formed in our nonflat AlGaN layers, which originated from the macrosteps along [11–20] edgelines normal to the m[1–100] axis, are suggested to be metastable. The creation of discrete xAl in Ga-rich zones should contribute to the stable production of DUV-LEDs using high-miscut sapphire substrates.

AlGaN-based deep-ultraviolet light-emitting diodes (LEDs) incorporating uneven multiple quantum wells (MQWs) with inclined and terrace zones, which were fabricated on an AlN template with dense macrosteps, have exhibited a high internal quantum efficiency (IQE). To investigate the microscopic structure of uneven MQWs, cathodoluminescence (CL) mapping characterization was carried out, and the maps of the CL intensity at 300 K relative to that at 38 K were obtained for uneven MQWs that targeted 265 and 285 nm LEDs. At an electron beam current of less than 1.0 nA, the signals from inclined and terrace zones of the uneven MQWs were confirmed to satisfy the nonsaturated excitation condition at 300 K. Nonradiative recombination (NR) was insufficiently frozen even at 38 K, specifically on the terraces in the 265 nm MQW, suggesting high concentrations of NR centers due to point defects (PDs). In contrast, NR in the 285 nm MQW at 38 K was closer to freeze-out. The concentration of PDs in the 285 nm MQW was likely to be lower than that in the 265 nm MQW. Finally, the ratios of the CL intensity at 300 K to those at 38 K were mapped, demonstrating an approach to creating an approximate map of IQE. The values in the CL intensity ratio maps are discussed by considering the analytical error factors. The results support the model of localized current injection through Ga-rich stripe zones in the n-AlGaN cladding layer.

The reaction mechanism for electrochemical‐vapor deposition of yttria‐stabilized zirconia was studied. Yttria‐stabilized zirconia films were deposited on porous La(Sr)MnOx using the electrochemical‐vapor‐deposition process. The distribution of yttria concentration through the film was investigated by means of secondary‐ion‐mass spectroscopy and x‐ray microanalysis and found to be nearly constant. The deposition rate was approximately proportional to the minus two‐thirds power of the film thickness, the one‐third power of the partial pressure of ZrCl4/YCl3 mixed gas, and the two‐thirds power of the product of the reaction temperature and the electronic conductivity of yttria‐stabilized zirconia film. These experimental results were explained by a model for electron transport through the YSZ film and reaction between the surface oxygen and the metal chloride on the chloride side of the film, both of which affect the deposition rate. If the film thickness is very small, the deposition rate is thought to be c...

Measurements were made on the Hall effect of SnO2 thin‐film inflammable gas sensors prepared by using the reactive sputtering method. The results revealed that when the electrical conductivity of the sensors changed with a change in the flammable gas concentration in air, the apparent carrier density changed significantly while apparent mobility hardly changed at all. However, detailed analysis revealed that these experimental results could not be explained by using the double Schottky model or the neck model that had been proposed. In order to provide satisfactory explanation of the experimental results, the authors clarified that for SnO2 thin films there exists no distinction between bulk and surface of the grain while the carrier densities of bulk and surface of the grain simultaneously change with a change in oxygen absorption of the SnO2 surface in the presence of flammable gas. This model was in good agreement with the results of transmission electron microscopy observations.