Search

A study on the neutron production from single and double gas puff Z-pinches on the CESZAR linear transformer driver with ∼0.45 MA current and 170 ns rise time is presented. Total neutron yield measurements made with a LaBr activation detector are compared for three configurations, using a double nozzle setup. When a single, hollow, deuterium gas shell was used, reliable implosions could only be attained at higher load mass than the optimal value to match implosion time with the driver rise time, with neutron yields of ∼106 per pulse. The use of a double gas puff configuration with a deuterium center jet allowed a reduction in the shell density and operation closer to machine-matched conditions, recording up to (4.1 ± 0.3) × 107 neutrons/pulse when either Kr or D2 was used in the shell. For a comparable mass and implosion time, using a higher atomic-number gas in the outer shell results in more unstable plasma surface and smaller plasma radius at the location of instability bubbles, which, however, do not seem to consistently correlate with a higher neutron yield. Comparing implosion dynamics with models and neutron yields with literature scaling suggests that the machine current is not well coupled to the plasma during the final stages of compression. Optimizing current and energy coupling to the pinched plasma is critical to improving performance, particularly in low-impedance drivers. [ABSTRACT FROM AUTHOR]

The ion emission properties of laser-produced plasmas as a function of laser intensities between 4–50 GW cm − 2 and varying angles with respect to the target normal were investigated. The plasmas were produced by focusing 1064 nm, 6 ns pulses from an Nd:YAG laser on various metal targets. The targets used for this study include Ti, Mo, and Gd (Z = 22 , 42 , 64). It is noted that all ion profiles are composed of multiple peaks—a prompt emission peak trailed by three ion peaks (ultrafast, fast, and thermal). Experimentally, it is shown that each of these ion peaks follows a unique trend as a function of laser intensity, angle, and distance away from the target. Theoretically, it is shown that simple analytical models can be used to explain the properties of the ions. The variations in the ion velocity and density as a function of laser intensity are found to be in good agreement with theoretical models of sheath acceleration, isothermal self-similar expansion, and ablative plasma flow for various ion peaks. [ABSTRACT FROM AUTHOR]

Gas puff Z-pinch experiments with annular Ar and Ne gas shells have been conducted on the Compact Experimental System for Z-pinch and Ablation Research (CESZAR) linear transformer driver (LTD) with 500 kA current and 160 ns rise time. Here, we present results from the first systematic gas puff Z-pinch experiments using a fast (≤ 200 ns) LTD as a driver, in which we show that 7% of the stored energy in the capacitors is coupled to plasma kinetic energy as estimated via self-emission and laser schlieren images. 0D and 1D simulations—which do not allow instability growth and thus reach greater maximum average velocities—using initial conditions inferred from experimental implosion trajectories predict coupling in excess of 10% of the stored energy. The Ar and Ne implosions were comparably massed and thus achieved similar maximum kinetic energies, though the Ne pinches were more stable and the x-ray pulses were longer and produced higher yield: 2–5 ns and 0.21–0.52 J (0.15–0.37 J/cm) of Ar K-shell and 12–25 ns and 2.2–3.9 J (1.6–2.6 J/cm) of Ne K-shell, respectively. The difference in stability is most likely attributed to variations in initial conditions such as density distribution and gas breakdown initiation. [ABSTRACT FROM AUTHOR]

The dense plasma focus (DPF) can be an intense source of x rays, wherein the insulator sleeve strongly dictates the electrical breakdown, which subsequently affects the formation of a plasma sheath and a collapse phase. Experiments on a 25 kJ DPF (operated at 4.4 kJ) are carried out to demonstrate the influence of insulator surface morphology on the pinch structure, dynamics, and x-ray yield using a Ne fill. Two borosilicate insulators are directly compared, one with a smooth finish and the other machined with four circumferential grooves traversing the perimeter of the exterior insulator surface. Comparisons are made through same-shot imaging diagnostics of the evolving plasma sheath during breakdown, rundown, and at the pinch in addition to the time-resolved measurements of emitted x rays via filtered photodiodes. The presence of structures on the insulator sleeve reduces x-ray production across all fill pressures by a factor of 2.8 ± 2.4 on average and reduces the highest x ray producing shots by a factor of 5.5 ± 1.8. Observations of sheath asymmetry and inhomogeneity at lift-off are observed and correlated with subsequent observations of off-axis radial collapse. Taken together, this suggests that local variations in the insulator surface decrease the spatial uniformity of the sheath, leading to an azimuthally asymmetric focus, reduced electron densities, and, ultimately, degraded x-ray production. [ABSTRACT FROM AUTHOR]

Wire X-pinches (WXPs) have been studied comprehensively as fast (∼ 1 ns pulse width), small (∼ 1 μ m) x-ray sources, created by twisting two or more fine wires into an "X" to produce a localized region of extreme magnetic pressure at the cross-point. Recently, two alternatives to the traditional WXP have arisen: the hybrid X-pinch (HXP), composed of two conical electrodes bridged by a thin wire or capillary, and the laser-cut foil X-pinch (LCXP), cut from a thin foil using a laser. We present a comparison of copper wire, hybrid, and laser-cut foil X-pinches on a single experimental platform: UC San Diego's ∼ 200 kA, 150 ns rise time GenASIS driver. All configurations produced 1–2 ns pulse width, ≤ 5 μ m soft x-ray (Cu L-shell, ∼ 1 keV) sources (resolutions diagnostically limited) with comparable fluxes. WXP results varied with linear mass and wire count, but consistently showed separate pinch and electron-beam-driven sources. LCXPs produced the brightest (∼ 1 MW), smallest (≤ 5 μ m) Cu K-shell sources, and spectroscopic data showed both H-like Cu K α lines indicative of source temperatures ≥ 2 keV, and cold K α (∼ 8050 eV) characteristic of electron beam generated sources, which were not separately resolved on other diagnostics (within 1–2 ns and ≤ 200 μ m). HXPs produced minimal K-shell emission and reliably single, bright, and small L-shell sources after modifications to shape the early current pulse through them. Benefits and drawbacks for each configuration are discussed to provide potential X-pinch users with the information required to choose the configuration best suited to their needs. [ABSTRACT FROM AUTHOR]

Experiments on a MA-class Dense Plasma Focus (DPF) device have been carried out to investigate changes in neutron production by adding moderate amounts of krypton to a deuterium fill gas. The neutron yield from Z-pinch devices, including DPFs, conventionally scales as the peak current to the fourth power. However, a dramatic drop-off from ∼I4 scaling occurs above 3 MA, which recent modeling [D. T. Offermann et al., Phys. Rev. Lett. 116, 195001 (2016)] attributed to the transition in the predominant neutron production mechanism from beam-target fusion to thermonuclear fusion. Previously, the addition of Kr (and other high-Z) dopants has been shown to enhance beam-target fusion yields at currents below 300 kA, with optimal concentrations at 1%–2% Kr, whereas here we show that the optimal concentration of Kr at the MA level is near 0.1% by volume—elucidating a trend in the optimal Kr doping concentration as a function of the device scale. The neutron time-of-flight data reveal that Kr doping creates shorter and more intense neutron bursts, likely due a tighter but unstable pinch, highlighting a key trade-off for Kr doping. [ABSTRACT FROM AUTHOR]

A theoretical study complemented with published experimental data of proton acceleration from sub-micron (thickness < 1 µm) foils irradiated by ultra-high contrast (>1010) short pulse lasers is presented. The underlying physics issues pertinent to proton acceleration are addressed using two-dimensional particle-in-cell simulations. For laser energy ε ≤ 4 J (intensity I ≤ 5 x 1020 W/cm²), simulation predictions agree with experimental data, both exhibiting scaling superior to Target Normal Sheath Acceleration's model. Anomalous behavior was observed for ε > 4 J (I > 5 x 1020 W/cm²), for which the measured maximum proton energies were much lower than predicted by scaling and these simulations. This unexpected behavior could not be explained within the frame of the model, and we conjecture that pre-pulses preceding the main pulse by picoseconds may be responsible. If technological issues can be resolved, energetic proton beams could be generated for a wide range of applications such as nuclear physics, radiography, and medical science. [ABSTRACT FROM AUTHOR]

Studies a two kJ, 200 kA, table top plasma focus device as an intense x-ray source. Measurement of the x-ray yield from gases as a function of filling pressure and in neon as a function of anode length; Temperature estimated from spectroscopic observations.