Search

Although the study of quasi-2D magnetism is well-established in bulk materials, the study of literal 2D magnets - consisting of a single layer of magnetic ions - is quite limited. Four of the contributed papers report experimental work on nanostructures: three of these involve superconductivity and one is on magnetism. Proximity effects in superconductors have been known for nearly 90 years,[13] but until recently proximity effects in magnets have been harder to study due to the much smaller range of the proximity effect in magnets compared to superconductors. One of the most exciting recent developments in quantum materials is the discovery and characterization of magnetism and superconductivity in exfoliated single-layer materials. [Extracted from the article]

This paper proposes a piezoelectric energy harvester that concentrates force on the piezoelectric element by parallel springs. When vibrating, the force exerted by the mass is released at three equal points on the surface of the brass substrate through three parallel springs. This concentrated release of energy through the spring amplification effect facilitates large deformation of the piezoelectric ceramic sheet, resulting in a higher charge output. The results show that under the combined action of a 14 g annular hollow mass and a 0.3 mm wire diameter stainless steel spring, the energy harvester based on the lead zirconate titanate ceramic exhibited an outstanding output power of 1.0–32.1 mW at a low resonance frequency with acceleration amplitudes of 0.5–3 g (1 g = 9.8 m/s2). More importantly, to match the vibration frequency of the actual environment, this paper optimized the structure of the harvester and proposed that the harvester can be designed by selecting the weight of the mass block, the parameters and number of springs, and the shape of the brass substrate. The energy harvester designed in this study is expected to capture energy from low-frequency natural environments and exhibit outstanding output performance, which can provide guidelines for future efforts in this direction. [ABSTRACT FROM AUTHOR]

This paper describes the design and optimization of a 10 ml cartridge for patient sample processing using a 3.5 GHz (empty resonant frequency) TM010 cylindrical microwave cavity. The cartridge has been designed to augment a novel approach for the rapid diagnosis of M. tuberculosis (the causative agent of Ttuberculosis), which uses the direct application of microwaves to a bacteria-containing sample to release pathogen-specific DNA. The target bacterial DNA is then captured and recovered using magnetic nanoparticles coated with pathogen-specific DNA probes. Excitation parameters were optimized using three surrogates for M. tuberculosis, namely, M. smegmatis, M. abscessus, and M. bovis suspended in water and simulated sputum. The paper also explores the mechanism of microwave-mediated DNA release from bacteria using scanning electron microscopy. Examination of bacteria exposed to microwaves at power levels known to mediate the release of DNA reveals no obvious signs of permanent cell disruption, suggesting that a more subtle interaction is taking place. Finally, the presence of microwave-liberated M. bovis DNA was able to be detected at a level of sensitivity comparable to that achieved using microscopy. [ABSTRACT FROM AUTHOR]

As one of the promising room temperature nuclear radiation detection materials, the all-inorganic perovskite CsPbBr3 single crystal has been receiving much attention in recent years. Even though the performance of the CsPbBr3 detector is improving continuously, the disadvantages of detection instability have not been solved fundamentally, and this instability is mainly caused by ionic migration in the CsPbBr3 single crystal itself. In this paper, a reasonable ionic migration model is proposed based on an in-depth study of the current hysteresis phenomenon and ionic migration mechanism in the Ti/CsPbBr3/Ti detector. The model shows that the ions migrate to the anode or cathode under an external electric field, and the accumulated ions subsequently form an inverted internal electric field inside the crystal and carrier transport barriers at the metal–semiconductor interface simultaneously. The photoelectric characteristic and ionic migration activation energy (E a i o n) fitting results also prove the rationality of the ionic migration model. Furthermore, the ionic migration model can also be used to explain the left-shift of the energy response peak and the decrease in the normalized charge collection efficiency in the Ti/CsPbBr3/Ti detector. This paper systematically investigates the intrinsic origin of migrated ions and the influence of ionic migration on detection stability, which will provide a potential solution to improve detection stability by suppressing ionic migration in the near future. [ABSTRACT FROM AUTHOR]

In this paper, the super-cavitating phenomenon under the effect of two vehicles' encounter motion processes is numerically studied. Particular attention is given to the influence of the vertical gaps between the vehicle, the cavitation number, and the slenderness ratio on the cavity profile and radial force of the object. Several numerical models are built to study the cavity evolution process and the force acting on the vehicle to explore the influence mechanism of two vehicles' encounter motion on supercavitating flow. The study shows that the cavity around the vehicle is primarily affected by the vertical gaps and cavitation number, but is relatively weakly affected by the slenderness ratio. Several impact laws are acquired in the paper. The relationship between cavity fracture time and vertical gaps is approximately a power function and obeys the law of t = 5.433h0.3688. The concept of the time of the maximum radial force occurrence and the cavitation number follows the formula of t = 4.86e0.3688σ. The relationship between the maximum radial force occurrence position and the cavitation number is a function of Ln and consistent with the law n = −0.799ln(σ) + 8.427. [ABSTRACT FROM AUTHOR]

Dynamic shockless compression experiments provide the ability to explore material behavior at extreme pressures but relatively low temperatures. Typically, the data from these types of experiments are interpreted through an analytic method called Lagrangian analysis. In this work, alternative analysis methods are explored using modern statistical methods. Specifically, Bayesian model calibration is applied to a new set of platinum data shocklessly compressed to 570 GPa. Several platinum equation-of-state models are evaluated, including traditional parametric forms as well as a novel non-parametric model concept. The results are compared to those in Paper I obtained by inverse Lagrangian analysis. The comparisons suggest that Bayesian calibration is not only a viable framework for precise quantification of the compression path, but also reveals insights pertaining to trade-offs surrounding model form selection, sensitivities of the relevant experimental uncertainties, and assumptions and limitations within Lagrangian analysis. The non-parametric model method, in particular, is found to give precise unbiased results and is expected to be useful over a wide range of applications. The calibration results in estimates of the platinum principal isentrope over the full range of experimental pressures to a standard error of 1.6%, which extends the results from Paper I while maintaining the high precision required for the platinum pressure standard. [ABSTRACT FROM AUTHOR]

This paper presents a self-consistent multi-dimensional mathematical model and a numerical approach for simulating the low-temperature plasma induced by the femtosecond laser filament. Addressing limitations in current models, we analyze key aspects of the laser plasma behavior, including plasma generation, detailed chemical kinetics, energy exchange channels, total energy balance, and hydrodynamics. The developed model and LOTASFOAM code are applied to study the temporal and spatial decay of the plasma produced by a femtosecond laser pulse in pure nitrogen at atmospheric pressure. The paper also includes a discussion on the spatial and temporal dynamics of electronically excited states of nitrogen in the decaying laser plasma. [ABSTRACT FROM AUTHOR]

In this paper, an ultra-thin absorber with a total thickness of 9.2 mm is designed and verified at the frequency band of 1–5.34 GHz. The absorber is composed of a layer of metasurface, multi-layered magnetic substrate, a layer of fragmented magnetic structure obtained by improved MOEA/D-GO (Multi-Objective Evolutionary Algorithm based on Decomposition combined with Enhanced Genetic Operators), and a copper back plate. The absorber is achieved by two steps. First, we designed and measured an ultra-thin absorber at 0.78–2.04 GHz by adding a layer metasurface onto the top of a basic multi-layer absorber composed of magnetic materials. The fractional bandwidth (FBW) of the absorber is 89.4%, and the electrical thickness is only 0.024 λ 0 at the lowest operating frequency. Second, to broaden the bandwidth, we use an improved MOEA/D-GO to optimize one magnetic layer of the absorber. The working frequency band of the optimized absorber is 1–5.34 GHz, covering L- (1–2 GHz), S- (2–4 GHz), and partial C-bands (4–8 GHz). Furthermore, we modified the structure of the metasurface to make the absorber polarization-independent. The FBW of the final absorber is 136.4%, and the electrical thickness is 0.031 λ 0 at the lowest operating frequency. The prototype of the absorber is measured, and the experimental results agree well with the simulated performance. The results show that the improved MOEA/D-GO can be used to design and optimize sophisticated electromagnetic (EM) structures with the predesigned properties, and the absorber with ultrathin thickness and light weight verified in this paper have great application potentials in EM compatibility, EM shielding, and radar cross section reduction at the low bands of the microwave spectrum. [ABSTRACT FROM AUTHOR]

In this paper, a Zr–5W alloy was fabricated via casting. In order to obtain the mechanical properties of the material, quasi-static compression tests at room temperature and split Hopkinson pressure bar tests at various temperatures were carried out. The x-ray diffraction result showed that the main components of the alloy were αZr and W2Zr, where αZr is the matrix and W2Zr is the reinforcement. The metallographic characterization results showed that there were two main forms of W2Zr in the material, namely, large particle boundary and small diffuse submicrometer precipitates. The reinforcements of both distributions have the effect of increasing the strength of the material, but the small submicrometer W2Zr precipitates would cause microcrack nucleation during the late plastic deformation stage, resulting in damage softening. In order to make theoretical calculations of the mechanical properties of materials, the Johnson–Cook (JC) constitutive model and Zerilli–Armstrong (ZAM) constitutive model of the material were obtained. It was found that the JC constitutive model had poor consistency in describing material properties. Although the consistency of the ZAM constitutive model was higher than that of the JC constitutive model, it still had obvious shortcomings. Combined with the deformation mechanism of the alloy, a modified constitutive relation was established by adding damage softening terms based on the hexagonal close-packed metal constitutive model inferred by the kinetics of heat-activated dislocations. The relative error results of all working conditions show that the correlation consistency of the improved constitutive model in this paper is significantly better than that of JC constitutive and ZAM constitutive. [ABSTRACT FROM AUTHOR]

Digital fringe projection profilometry based on phase-shifting technology is a reliable method for complex shape measurement, and the phase is one of the most important factors affecting measurement accuracy. The calculation of the absolute phase depends on the calculation of the wrapped phase and encoding technology. In this paper, a technique of obtaining the absolute phase of multi-frequency heterodyne fringe images using the Hilbert transform is presented. Since the wrapped phase can be calculated from only one fringe image of each frequency, the method does not need phase-shifting. The absolute phase can be obtained from the wrapped phase by applying the heterodyne method. The measurement time and computational complexity are dramatically reduced, the measurement efficiency is greatly improved, and this benefit from the number of images is greatly reduced. The experimental results show that the method presented in this paper performs well in the application, and the accuracy is no different from that of the phase-shifting method while the efficiency is greatly improved. [ABSTRACT FROM AUTHOR]

In alloy solidification, the transport processes of heat and solute result in morphological instability of the interface, forming different patterns of the solidification structure and determining the mechanical properties of components. As the first observable phenomenon of morphological instabilities, planar instability influences the subsequent stages significantly, deserving in-depth investigations. In this paper, the planar instability in alloy solidification under varying conditions is studied. First, the dynamical evolution of the planar instability is performed by the theoretical model and the phase-field model, respectively. Second, to represent the history-dependence of solidification, varying parameters are adopted in the simulations. Then, the criterion of planar instability under varying conditions is discussed. This paper considers that the critical parameters of planar instability are the excess free energy at the interface and the corresponding interfacial energy. Finally, to validate the criterion, comparisons between the phase-field and theoretical models are carried out, showing good consistency. Moreover, solidification processes with different preferred crystallographic orientations are performed, demonstrating the effect mechanism of the excess free energy and interfacial energy on planar instability. The idea of the interfacial energy influencing the planar instability could be applied to investigating other patterns induced by interfacial instability. [ABSTRACT FROM AUTHOR]

This paper proposed a two-dimensional composite square lattice structure containing two kinds of inclusions (polymethylmethacrylate and T2 copper). To maximize the relative widths of the gaps between the adjacent energy bands of the phononic crystals (PnCs), an improved multi-parameter genetic algorithm was adopted in this paper. The material distribution and ligament sizes were considered simultaneously by ternary encoding and binary encoding. The propagation wave behaviors of the composite lattice structures were studied by the finite element method. The effects of different lattice shapes and other relevant influencing parameters on the bandgaps were discussed. The results showed that the lattice shape, ligament width, and material density affect the width and the location of the bandgaps, and the effectiveness of the proposed method was demonstrated by a transmission spectrum experiment. [ABSTRACT FROM AUTHOR]

The efficiency of quantum computing has recently been extended to machine learning, which has made a significant impact on quantum machine learning. The hybrid structure of quantum and classical ones has developed into the most successful application mode currently due to noisy intermediate scale quantum limitations. In this paper, an improved hybrid quantum-classic convolutional neural network (HQC-CNN) with fast training speed, lightweight, and high performance is proposed. Its convolution layer realizes feature mapping through parameterized quantum circuit, while other layers keep classic operation and finally complete the task of four classifications of brain tumors. The experiment in this paper is based on kaggle brain tumor magnetic resonance imaging public dataset. The final experimental results show that HQC-CNN can effectively classify meningioma, glioma, pituitary, and no tumor with a classification accuracy of 97.8%. When compared to numerous well-known landmark models, HQC-CNN has obvious advantages. [ABSTRACT FROM AUTHOR]

In spite of the flexoelectric effect being a universal phenomenon in the ferroelectric perovskites, the current understanding of flexoelectric aging in ferroelectrics is, actually, rather incomplete. In this paper, we have fabricated a series of Mn-doped BaTiO3 perovskite ceramics (BaTi1–xMnxO3, x = 0.1% and 1%, BTMO) to systematically investigate the corresponding flexoelectric aging behavior by controlling the concentration of Mn. We found that the variation of Mn dopant significantly effects the Curie temperature, dielectric constant, flexoelectric aging, and flexoelectric coefficient of the BTMO ceramics. Especially for the BTMO (0.1%) ceramics, obvious ferroelectric aging and flexoelectric aging phenomenon are observed at room temperature. The main reason for aging of BTMO ceramics is that the doping of Mn introduces oxygen vacancies, which tend to be stable under the action of strain gradient and electric field. Therefore, the results presented in this paper verify that the flexoelectric aging in Mn-doped BTO ceramics is closely related to ferroelectric fatigue. [ABSTRACT FROM AUTHOR]

An optical shutter based on charged particles is presented. The output light intensity of the proposed device has an intrinsic dependence on the interparticle spacing between charged particles, which can be controlled by varying voltages applied to the control electrodes. The interparticle spacing between charged particles can be varied continuously and this opens up the possibility of particle based displays with continuous grayscale. [ABSTRACT FROM AUTHOR]

Thin films deposited on wafers show, in some cases, large variations in stress. The local curvature is often used in the Stoney equation [G. G. Stoney, Proc. R. Soc. London, Ser. A 82, 172 (1909)] to calculate the local stress. This practice leads to false stress results. A general method for the calculation of the film stress, for films with isotropic stress, is presented here. The stress is calculated from both the local and overall shape of the substrate. Simple examples of isotropic stress were simulated and the substrate deformation calculated. The film stress was calculated back from the substrate shape with good agreement with the initial stress distribution. The substrate shape under films with centrosymmetric stress distribution can be analytically calculated. The current method successfully calculates the stress distribution from the substrate shape. Some guidelines for the deviation of the calculated stress from that of Stoney’s are given. Finally, the case of nonisotropic stressed film cannot be generally solved since there is no unique stress distribution for any given substrate shape. [ABSTRACT FROM AUTHOR]

The article announces that the "Journal of Applied Physics" will present the special topic section "Invited Papers From the 27th International Conference on Defects in Semiconductors, July 2013."

Understanding the properties of N-implanted β-Ga2O3 is fundamental for the optimization of doping and isolation structures based on gallium oxide. This paper reports an extensive analysis of the impact of thermal annealing on the concentration and properties of deep levels in N-implanted β-Ga2O3 Schottky barrier diodes by means of capacitance isothermal transient spectroscopy. Samples with annealing temperatures from 800 to 1200 °C were considered. The original results presented in this paper demonstrate the following: (a) The instability of current–voltage characteristics detected for all the samples under test can be attributed to the presence of three electron traps with activation energies of 0.6, 0.7, and 1 eV, consistent with previous reports in β-Ga2O3. (b) The detected traps are not the nitrogen level but intrinsic defects whose concentration is increased by the implantation process. (c) The concentration of deep levels decreases as the annealing temperature increases, demonstrating that the annealing process can effectively restore the quality of the material while keeping the conductivity decrease related to the presence of the nitrogen. Finally, (d) we demonstrate that the residual leakage and the turn-on voltage shift are correlated with the Arrhenius signature of the detected deep levels. An interpretation is proposed to explain the measurement results. [ABSTRACT FROM AUTHOR]

This paper studies the magnetization mechanism of a hybrid high temperature superconducting (HTS) trapped field magnet. To address the size limitation of traditional HTS bulk materials, hybridization between HTS-stacked ring magnets and HTS bulks is proposed here. A jointless HTS-stacked ring magnet is used to increase the trapped field area for HTS bulks. A hybrid HTS magnet with 90 mm in length and 60 mm in width was tested to provide a trapped field of 7.35 T in a field cooling magnetization. The paper focuses mainly on understanding the novel magnetization mechanism of this hybrid HTS trapped field magnet. A numerical model based on homogenized H formulation was used to compare with experimental results, and a good match was found. Our experimental and numerical study of the electromagnetic interaction between the HTS-stacked ring magnet and the HTS bulks reveals that there are two magnetization stages, and the magnetization speed differs in these two stages by a sing criterion: whether the HTS-stacked ring magnet is fully penetrated or not. This study confirms that hybridization helps to build large HTS trapped field magnets. [ABSTRACT FROM AUTHOR]

Accurate calculation of the tunneling currents in a scanning tunneling microscope (STM) is needed for developing image processing algorithms that convert raw data of the STM into surface topographic images. In this paper, an accurate calculation of the tunneling current for several tip–sample distances, bias voltages, and tips of a hyperboloidal shape with several radii of curvature is carried out. The main features of this calculation are the following. Non-WKB exact solutions to the trapezoidal (linear) potential in the barrier region are used to calculate the tunneling probabilities. Pauli blocking effects on both forward and reverse current densities are introduced. Finite temperature (viz. 300 K) calculation in which electrons belonging to a narrow band of energy about the Fermi level contribute to tunneling is carried out. Integration over a field line method is used to obtain tunneling currents for the nonplanar hyperboloidal shaped tips, using the expressions obtained in the paper, for planar model current densities. An estimate of the lateral resolution is introduced. Earlier works do not consider all these aspects together in a single calculation. Tunneling currents are found to increase rapidly with increasing bias voltage and decrease exponentially with increasing tip–sample distances. Airy function determined currents are a more accurate function of a tip–sample distance than the WKB determined currents. Pauli effects are found to not always reduce currents from their non-Pauli values. The lateral resolution is found to be degraded for blunter tips, larger bias voltages, and larger tip–sample distances. [ABSTRACT FROM AUTHOR]

Carbon nanotube (CNT) cathodes have attracted much attention in recent years due to the advantages of large field enhancement factor and low emission threshold. However, the severe ablation under intense emission makes the lifetime short and therefore limits the application in the field such as high power microwave generation. To resolve this problem, this paper proposes to mix CNTs with metals, and a novel CNT/Cu composite cathode is manufactured. The lifetime experiments under voltage of 940 kV and repetition frequency of 20 Hz demonstrate that the lifetime of the CNT/Cu composite cathode is over 3 × 105 pulses, which is much longer than that of the normal copper cathode by at least one order of magnitude. The microscopic morphology analysis reveals that the CNT micro-protrusions and whiskers should be vital for the good emission property of the new cathode. [ABSTRACT FROM AUTHOR]

The mode manipulation of Lamb waves plays an important role in damage detection and identification of damage types, location, and size. In this paper, we propose a composite phononic crystal (PC) plate with antisymmetric and symmetric PCs for realizing mode conversion from A0 to S0 mode of Lamb waves. The theoretical analysis, numerical simulations, and experimental validation are introduced and the mode conversion mechanism of the composite PC plate is systematically investigated. The effect of geometrical parameters on band structures of antisymmetric and symmetric PCs is first discussed. Then multi-physics field simulation models are developed and in-plane displacement fields are obtained in numerical simulations, which shows that the mode conversion is enhanced when the period number of the antisymmetric PC decreases and that of symmetric the PC increases. The composite PC plate specimens are fabricated with precision wire cutting technology for experimental measurements and the self-designed polyvinylidene fluoride (PVDF) comb transducer is used to stimulate the Lamb waves. The experimental results are consistent with the numerical simulations, which demonstrate that the proposed composite PC plate can achieve the mode conversion from A0 to S0 mode of Lamb waves. Our proposed structures have applicable values for the mode manipulation of Lamb waves in damage detection. [ABSTRACT FROM AUTHOR]

Excitations that may appear in cavity magnonics experiments are examined with numerical micromagnetics using a recently developed semi-classical cavity magnonics theory. The theory is generally applicable to linear and nonlinear dynamic systems. In this paper, example applications of the theory for magnetic systems are presented where the dynamics is described using numerical micromagnetics for field driven ferromagnets. Examples of large amplitude driving are studied as a function of drive field amplitude and frequency. We comment also on large amplitude dynamics under elliptically polarized driving fields. The main conclusion is that when implemented together with micromagnetics, the theory can be used to describe cavity photon–magnon coupling for a wide variety of linear and nonlinear magnetic dynamics, thereby providing a useful technique for cavity magnonics. [ABSTRACT FROM AUTHOR]

Understanding the mechanisms of unidirectional magnetoresistance (UMR) has become an important topic for its potential application of a two-terminal spin–orbit torque device. Field sweep DC measurements have been proposed and adopted to measure the value of UMR instead of second harmonic measurements. In this paper, potential measurement errors in conventional DC measurements are investigated. Oersted field and field-like torque usually do not influence the measurement, but a large field-like torque was found to lead to an anisotropic magnetoresistance difference when the sample is not perfectly aligned with the external field. The existence of ordinary magnetoresistance was also found to contribute to a large background. In this paper, an alternative measurement method for UMR was proposed and demonstrated to address those issues related to previous DC measurements. Our work may broaden the understanding of the error sources of UMR measurements and provide a reliable DC measurement method for the characterization of UMR. [ABSTRACT FROM AUTHOR]

Electrodynamic suspension (EDS) with a linear permanent magnet Halbach array, which can be used in ultrahigh-speed maglev systems, has gained increasing attention in recent years. However, inefficient calculation methods of electromagnetic forces restrict the stability research of EDS systems. Hence, an efficient 3D analytical model of the electromagnetic force is established in the paper based on an improved analytical model of the source magnetic field excited by the Halbach array, and then the application conditions of the model are studied. Finally, the analytical results are compared with the experimental results, which are provided by the experiments carried out on a high-speed rotating experiment platform with a flywheel. The results show that the proposed model can shorten the computation time of electromagnetic force to less than 10 ms and the relative errors of analytical results are around 5% under the conditions ① w p / τ ≥ 2.5 , w d / w p ≥ 1.5 or ② w p / τ ≥ 4 , w d / w p ≥ 1 (τ is the pole pitch of the Halbach array, w p is the width of the permanent magnet, w d is the width of the conducting plate). The analytical model meets the engineering requirements and can provide a reference for further stability research and experiments on EDS systems. [ABSTRACT FROM AUTHOR]

The study of insulation degradation processes is crucial for the reliable operation of power equipment and electronic devices. The phase field method has been widely used in recent years to simulate the degradation process of insulation materials. However, the effect of space charge was ignored. In this paper, a novel phase field method based on the bipolar carrier transfer model is suggested. This model can simulate degradation under different temperatures and DC or combined AC/DC voltage. The cases under AC and combined AC/DC voltage at different temperatures are simulated by COMSOL. Methods to ensure model convergence are proposed. The results show that the field strength distribution under a combined AC/DC field is more uniform, especially for negative polarity. For the same voltage form, temperature and breakdown time show an exponential relationship. The results are consistent with those of previous experimental studies, proving the usability of the model. In addition, the processes of initiation, growth, and breakdown stage of the dielectric degradation process, as well as the stagnation period, are explored theoretically. The stagnation time at low temperatures under combined AC/negative DC voltage is long. The research in this paper is useful for insulation optimization design, condition assessment, and longevity prediction. [ABSTRACT FROM AUTHOR]

Wrinkling, creasing, and folding are frequent phenomena encountered in biological and man-made bilayers made by thin films bonded to thicker and softer substrates often containing fibers. Paradigmatic examples of the latter are the skin, the brain, and arterial walls, for which wiggly cross sections are detected. Although experimental investigations on corrugation of these and analog bilayers would greatly benefit from scaling laws for prompt comparison of the wrinkling features, neither are they available nor have systematic approaches yielding to such laws ever been provided before. This gap is filled in this paper, where a uniaxially compressed bilayer formed by a thin elastic film bonded on a hyperelastic fiber-reinforced substrate is considered. The force balance at the film–substrate interface is here analytically and numerically investigated for highly mismatched film–substrates. The onset of wrinkling is then characterized in terms of both the critical strain and its corresponding wavenumber. Inspired by the asymptotic laws available for neo-Hookean bilayers, the paper then provides a systematic way to achieve novel scaling laws for the wrinkling features for fiber-reinforced highly mismatched hyperelastic bilayers. Such novel scaling laws shed light on the key contributions defining the response of the bilayer, as it is characterized by a fiber-induced complex anisotropy. Results are compared with finite element analyses and also with outcomes of both existing linear models and available ad hoc scalings. Furthermore, the amplitude, the global maximum and minimum of ruga occurring under increasing compression spanning the wrinkling, period doubling, and folding regimes are also obtained. [ABSTRACT FROM AUTHOR]

This Perspective paper deals with an overview of particle-in-cell/Monte Carlo collision models applied to different plasma-propulsion configurations and scenarios, from electrostatic (E × B and pulsed arc) devices to electromagnetic (RF inductive, helicon, electron cyclotron resonance) thrusters, as well as plasma plumes and their interaction with the satellite. The most important items related to the modeling of plasma–wall interaction are also presented. Finally, the paper reports new progress in the particle-in-cell computational methodology, in particular, regarding accelerating computational techniques for multi-dimensional simulations and plasma chemistry Monte Carlo modules for molecular and alternative propellants. [ABSTRACT FROM AUTHOR]

This paper proposes a layer-by-layer acoustic travel time approximation method based on ray theory for total focusing method (TFM) imaging in carbon fiber reinforced polymer (CFRP) laminates. The method considers the anisotropy in every monolayer and heterogeneity of CFRP, which approximates the path of propagation as straight in the whole material. The application of this method to TFM imaging is called TravelTimeAppro-TFM. In comparison to isotropic-TFM and Dijkstra-TFM, the experimental results indicated that TravelTimeAppro-TFM outperforms isotropic-TFM in terms of imaging amplitude gain with a maximum gain of 4.67 dB. On the other hand, this approach reduces the computational work compared to Dijkstra-TFM. The proposed method demonstrates significant improvements in both focusing performance and the speed of calculation. This paper also investigates the effective angular range of the layer-by-layer acoustic travel time approximation method through experimental and finite element simulation analysis. [ABSTRACT FROM AUTHOR]

As we known waves contain important information, however, to realizing high-precision quantification for ocean exploitation and utilization is challenging. In this paper, we proposed a neural network for wave height detection by training the voltage waveform of a triboelectric nanogenerator (TENG). First, we analyzed the voltage signal obtained using a TENG. Second, we proposed a lightweight artificial neural network model that achieves a minimal monitoring error of 0.049% at low amplitudes and yields better monitoring results than the linear model. The findings presented in this paper enable the measurement of water surface waves and eliminate the influence of external factors on sensor performance. Wave parameters can be obtained using neural networks, and this work provides a new strategy for computational and intelligent applications by using wave data. [ABSTRACT FROM AUTHOR]

Second harmonic generation (SHG) is used to characterize the interfaces of centrosymmetric materials typically used in microelectronic/optoelectronic devices. For such applications, the materials are actually multi-layer stacks, and in this case, the SHG can be difficult to interpret and model. This paper presents the theory of the second harmonic light generated from multilayer structures. The focus is on describing the nonlinear boundary conditions at the interfaces between two different materials, taking into account the distinct contributions of bulk and interface regions. Using these conditions, it is possible to calculate the second harmonic signal from any stack of materials. In this paper, we address stacks containing silicon (100) because it is a material with numerous applications. The nonlinear polarization expressions of the surface and bulk of Si(100), according to Sipe et al. [Phys. Rev. B 35, 1129 (1987)], were integrated into nonlinear boundary conditions in order to determine transmitted and reflected second harmonic waves. An analytical validation was performed on the simple case of an air–silicon interface. For multilayered stacks, the model was compared with experimental results obtained on samples corresponding to pragmatic substrates widely used in microelectronic and optoelectronic applications. [ABSTRACT FROM AUTHOR]

The fluid description is widely used for the multi-dimensional modeling of low temperature plasmas with complex chemistries due to their relative low computational cost. It relies, however, on a series of simplifying assumptions and some truncation of the moment equations for describing the non-equilibrium between the electrons, positive ions, negative ions, and the neutrals. In this paper, the classical assumption of isothermal negative ions is revisited for electronegative plasmas and, more particularly, for the fluid modeling of the transition between the plasma and its sheath. To do so, and in contrast to previous studies, the energy balance equation for the negative ions is also computed, and it allows us to derive the polytropic coefficient γ of the negative ions in addition to one of the positive ions. Strong variations in the sheath and presheath of the negative ions temperature and their polytropic coefficient are observed. The polytropic coefficient is shown to be a strongly varying function of space having for consequence that the negative ions are isothermal only in a very narrow extension of the presheath. For the case considered in this paper, both positive and negative ion flows are nearly adiabatic at the sheath-edge and become adiabatic inside the sheath. This paper shows that classical fluid modeling assumptions need to be verified for each system under consideration, most particularly while modeling the transition from plasma to a wall. [ABSTRACT FROM AUTHOR]

We recently rigorously described using finite element analysis a cylindrical cavity resonator, with a cylindrical post inserted along the central axis. Such a cavity has a well known reentrant mode where an Ez field exists in the gap between the lid and the post. In McAllister et al., J. App. Phys. 122, 144501 (2017), we rigorously analysed higher order modes with similar characteristics to the well known reentrant mode, which we dubbed “higher order re-entrant post modes.” The author claims in S. Belomestnykh, J. Appl. Phys. 123, 226101 (2018) that these modes have been described before as foreshortened quarter-wave resonators. We discuss the differences between the results of rigorous finite element modelling and the model proposed in the comment and show that the proposed description is a crude non-Maxwellian model, only approximately valid in a finite region of the cavity tuning range with on average ∼9.6% agreement with experimental frequencies for the first higher order mode. The model assumes simple electromagnetic field patterns which do not satisfy Maxwell's equations, and we show that they vary significantly from the rigorous analysis based on Maxwell's equations. The foreshortened quarter-wave resonator model cannot be used to accurately calculate geometry factors or other factors that require precise knowledge of the fields, such as those computed in the design of cavities for axion experiments. We conclude that the reentrant mode description in the paper is favourable. [ABSTRACT FROM AUTHOR]

The article discusses the highlights of the 11th International Surface X-ray and Neutron Scattering (SXNS-11) Conference that took place at the Northwestern University (NU) campus in Evanston, Illinois from July 13-17, 2010. The conference, which was hosted by the NU Materials Research Science and Engineering Center, has gathered 164 delegates from 16 countries. Information on papers presented at the conference are presented.

In this paper, a frequency domain simulation method of magneto-acousto-electrical tomography (MAET) was proposed. This method is based on discrete Fourier transform. With this approach, the solving degrees of freedom of the simulation model can be significantly reduced. It can greatly reduce the requirements of computer hardware and improve efficiency. At the same time, the interaction between fluid and biological tissues was considered, which makes the simulation model closer to the real model. In this paper, an MAET simulation model of acoustic–solid–electromagnetic multi-physical field coupling corresponding to the actual physical world was established. It is more reasonable to adopt the fully coupled method. However, the fully coupled method needs more computational memory. To further study the memory and time required for calculation, the segregated method was used to calculate the simulation model without affecting the accuracy and tolerance in this paper. The results show that using the segregated method can significantly reduce the memory requirement of the MAET model, but the solution time will increase accordingly. Therefore, the appropriate solution method can be selected according to the simulation computer configuration and the desired solution time. We, finally, built an experimental platform to conduct MAET experiments and verified the theoretical and simulation analyses. [ABSTRACT FROM AUTHOR]